mirror CADILLAC DEVILLE 2002 8.G Owners Manual

1-5 Memory Seat, Mirrors and Steering Wheel
(If Equipped)
The controls for these
features are located on the
driver's door panel, and are
used to program and recall
memory settings for the
driver's seating positions.
Use the following steps to program each button:
1. Adjust the driver's seat (including the seatback
recliner, lumbar, head restraint and shoulder belt
height adjustments), both outside mirrors and the
steering wheel to a comfortable position.
2. Press the SET button.3. Within five seconds, press button 1. A single beep
will sound through the driver's side front speaker to
let you know that the position has been stored.
A second mirror, seating and steering wheel position can
be programmed by repeating the above steps and
pressing button 2 (for driver 2). Each time a memory
button is pressed, a single beep will sound. Each time
button 1 or 2 is pressed and released while the vehicle
is in PARK (P), the memory positions will be recalled.
If the vehicle is not in PARK (P), the memory buttons
must be pressed and held to recall the stored positions.
If you use the remote keyless entry transmitter to enter
your vehicle, automatic seat and mirror movement will
occur. The numbers on the back of the transmitters,
1 and 2, correspond to the numbers on the buttons on
the door panel.
When the key is placed in the ignition in OFF if you
have entered the vehicle without using the remote
keyless entry transmitter, the seats and mirrors will
automatically adjust to the programmed position of
the last driver.
To stop recall movement of the memory feature at
any time, press one of the power seat controls or
memory buttons.

1-6
Two personalized exit positions can be set by first
recalling the driving position (by pressing 1 or 2), then
positioning the steering wheel and seat in the desired
exit positions and then pressing and releasing the
MEMORY SET button and, within five seconds,
pressing the EXIT button. With the vehicle in
PARK (P), the exit position for the last driver can be
recalled by pressing the EXIT button. The mirrors,
power lumbar and shoulder belt height positions will
not be stored or recalled for the exit positions.
Further programming for automatic seat and mirror
movement can be done using the Driver Information
Center (DIC). You can select or not select the following:

Automatic seat and mirror movement when the
vehicle is unlocked with the remote keyless entry
transmitter, or

automatic seat and mirror movement when a key is
placed in the ignition.
For programming information, see ªVehicle
Programming and Personalization Featuresº in
the Index.Heated Seats (If Equipped)
Your vehicle may have heated front and rear seats.
The buttons are located on the armrests. Press the
buttons to turn the feature on. Press them again to turn
off the heated seats. The feature will also shut off when
the ignition is turned to OFF.

2-
2-1
Section 2 Features and Controls
Here you can learn about the many standard and optional features on your vehicle, and information on starting,
shifting and braking. Also explained are the instrument panel and the warning systems that tell you if everything
is working properly
-- and what to do if you have a problem.
2
-2 Windows
2
-5 Keys
2
-7 Door Locks
2
-10 Remote Keyless Entry System
2
-14 Trunk
2
-17 Theft
2
-18 Theft-Deterrent System
2
-20 PASS-Key
III
2
-22 New Vehicle ªBreak-Inº
2
-23 Ignition Positions
2
-25 Starting Your Engine
2
-26 Engine Coolant Heater (If Equipped)
2
-28 Automatic Transaxle Operation
2
-34 Parking Brake
2
-36 Shifting Into PARK (P)
2
-39 Shifting Out of PARK (P)
2
-39 Parking Over Things That Burn
2
-40 Engine Exhaust
2
-40 Running Your Engine While You're Parked2
-41 Tilt Wheel
2
-43 Turn Signal/Multifunction Lever
2
-50 Exterior Lamps
2
-56 Interior Lamps
2
-59 Mirrors
2
-63 Storage Compartments
2
-67 Rear Power Sunshade (If Equipped)
2
-70 Cellular Telephone (Option)
2
-70 OnStar
System (If Equipped)
2
-74 Sunroof (Option)
2
-75 HomeLink
Transmitter (If Equipped)
2
-78 The Instrument Panel -- Your
Information System
2
-85 Warning Lights, Gages and Indicators
2
-100 Driver Information Center (DIC)
2
-129 Navigation (Option)
2
-130 Night Vision System (Option)
2
-133 Ultrasonic Rear Parking
Assist (URPA) (Option)

2-11
Operation
(Lock): When you press
this symbol to lock the
doors, the parking lamps
will flash once and the horn
will sound. This arms the
theft
-deterrent system.
The parking lamps will not flash, however, if the manual
parking lamps are left on. Remote confirmation is not
operational if a door is open.
You can program your vehicle so the parking lamps
will not flash and the horn will not sound. For more
information, see ªLock/Unlock Confirmationº in
the Index.
(Unlock): When you press this symbol to unlock
the driver's door, the parking lamps on your vehicle will
flash twice. The parking lamps will not flash if they
have been turned on manually. Remote confirmation is
not operational if a door is open.Press this button again within one to five seconds
to unlock the other doors. It will also disarm the
theft
-deterrent system and turn on the interior
lamps at night.
You can program your vehicle so the parking lamps will
not flash. For more information, see ªLock/Unlock
Confirmationº in the Index.
(Panic Alarm): The remote keyless entry
transmitter comes equipped with an instant panic alarm.
To use the alarm, press the horn symbol when the
ignition is turned off. The horn will sound and the
exterior lamps will flash for up to 30 seconds. To stop
the instant panic alarm, press the symbol again or turn
the ignition to ON.
(Trunk): Press this button to open the trunk. The
valet lockout switch must be off for this feature to work.
The remote keyless entry transmitter can be used to
recall the memory settings for up to two drivers. For
more information, see ªVehicle Programming and
Personalization Featuresº and ªMemory Seat, Mirrors
and Steering Wheelº in the Index.

2-42
Power Tilt and Telescopic Wheel
(If Equipped)
The power tilt wheel control
is located on the outboard
side of the steering column.
To operate the power tilt feature, push the control up and
the steering wheel will tilt up. Push the control down
and the steering wheel will go down.If the power tilt control is pressed up or down and held
in that position, there will be a slight movement and a
slight pause followed by a continuous movement in the
direction the control is being pressed. This allows very
fine control of the steering wheel position. If the control
is bumped, the steering wheel moves approximately one
degree in the direction commanded.
Push the control forward and the steering wheel moves
toward the front of the vehicle. Push the control rearward
and the steering wheel moves toward the rear of the
vehicle. To set the memory position, see ªVehicle
Programming and Personalization Featuresº and ªMemory
Seat, Mirrors and Steering Wheelº in the Index.

2-45
Be sure to clear ice and snow from the wiper blades
before using them. If they're frozen to the windshield,
carefully loosen or thaw them. If the blades do become
damaged, get new blades or blade inserts.
Heavy snow or ice can overload the wiper motor.
A circuit breaker will stop the motor until it cools.
Clear away snow or ice to prevent an overload.
Rainsense
II Wipers (If Equipped)
If your vehicle has this feature, the moisture sensor is
mounted on the interior side of the windshield behind
the rearview mirror. It is used to automatically operate
the wipers by monitoring the amount of moisture
build
-up on the windshield. Wipes occur as needed to
clear the windshield depending on driving conditions
and the sensitivity setting. In light rain or snow, fewer
wipes will occur. In heavy rain or snow, wipes will
occur more frequently. The Rainsense wipers operate in
a delay mode as well as a continuous low or high speed
as needed. If the system is left on for long periods of
time, occasional wipes may occur without any moisture
on the windshield. This is normal and indicates that the
Rainsense system is activated.The Rainsense system can be activated by turning the
wiper band to one of the five sensitivity levels indicated
on the wiper stalk. The position closest to OFF is the
lowest sensitivity setting, level one. This allows more
rain or snow to collect on the windshield between wipes.
Turning the wiper band away from you to higher
sensitivity levels increases the sensitivity of the system
and frequency of wipes. The highest sensitivity setting,
level five is closest to LO. A single wipe will occur each
time you turn the wiper stalk to a higher sensitivity level
to indicate that the sensitivity level has been increased.NOTICE:
The wipers must be turned off when going
through a car wash to avoid damage.

2-59
Mirrors
Electrochromic Day/Night Rearview Mirror
with Compass
Your vehicle has an electrochromic inside rearview
mirror with a compass. Your vehicle's mirror also
contains OnStar

controls. For more information about
OnStar, see ªOnStarº in the Index.
(On/Off): This is the on/off button, located on the
lower left side of the mirror for the electrochromic and
compass functions of the rearview mirror.
The mirror also includes an eight
-point compass
display in the upper right corner of the mirror face.
When on, the compass automatically calibrates as the
vehicle is driven.When cleaning the mirror, use a paper towel or similar
material dampened with glass cleaner. Do not spray
glass cleaner directly on the mirror as that may cause the
liquid cleaner to enter the mirror housing.
Mirror Operation
To turn on the automatic dimming feature, press
and hold the on/off button for about three seconds.
To turn off automatic dimming, press and hold the
on/off button for about three seconds again. The
indicator light will illuminate when this feature is active.
The automatic dimming feature is active each time the
vehicle is started.
Compass Operation
Press the on/off button once to turn the compass
on or off.
When the ignition and the compass feature are on, the
compass will show two character boxes for
approximately two seconds. After two seconds, the
mirror will display the compass heading.

2-60
Compass Calibration
If after two seconds, the display does not show a
compass heading (N for North, for example), there may
be a strong magnetic field interfering with the compass.
Such interference may be caused by a magnetic antenna
mount, magnetic note pad holder or a similar magnetic
item. If the letter C should ever appear in the compass
window, the compass may need calibration.
The mirror can be calibrated by driving the vehicle in
circles at 5 mph (8 km/h) or less until the display
reads a direction.
The compass can be placed in calibration mode by
pressing and holding the on/off button until a C is
shown in the compass display.Compass Variance
The mirror is set in zone eight upon leaving the factory.
It will be necessary to adjust the compass to compensate
for compass variance if you live outside zone eight.
Under certain circumstances, as during a long distance
cross
-country trip, it will be necessary to adjust for
compass variance. Compass variance is the difference
between earth's magnetic north and true geographic
north. If not adjusted to account for compass variance,
your compass could give false readings.
To adjust for compass variance, do the following:
1. Find your current location and variance zone number
on the following zone map.
2. Press and hold the on/off button until a zone number
appears in the display.

2-61
3. Once the zone number appears in the display, press
the on/off button quickly until the correct zone
number appears in the display. Stop pressing the
button and the mirror will return to normal
operation. If C appears in the compass window, the
compass may need calibration. See ªCompass
Calibrationº listed previously.
Power Remote Control Mirror
The control on the driver's
door armrest operates both
outside rearview mirrors.
Press (R) on the selector switch to choose the right
mirror or (L) to choose the left mirror. The center
position is off and will not move the mirrors if the
control pad is touched.
To adjust the mirror, press the arrows on the control pad
in the direction you want the mirror to go. Adjust each
mirror so you can see the side of your vehicle and the
area behind your vehicle.

2-62
The mirrors can be manually folded inward to prevent
damage when going through an automatic car wash. To
fold, push the mirror toward the vehicle. To return the
mirror to its original position, push outward. Be sure to
return both mirrors to their original unfolded position
before driving.
The mirrors can also be programmed for personalization
and parallel parking feature if you have the optional
memory package. For more information, see ªMemory
Seat, Mirrors and Steering Wheelº and ªVehicle
Programming and Personalization Featuresº in
the Index.
Driver's Outside Auto-Dimming
Rearview Mirror
The driver's side outside mirror will adjust for the glare
of headlamps behind you. This feature is controlled by
the on and off settings on the electrochromic mirror.
See ªElectrochromic Day/Night Rearview Mirror with
Compassº in the Index.
Curb View Assist Mirror (If Equipped)
If your vehicle is equipped with memory mirrors, it
will also be capable of performing the curb view assist
mirror feature. This feature will cause the passenger's
mirror to tilt to a preselected position when the vehicle
is in REVERSE (R). This feature may be useful
in allowing you to view the curb when you are
parallel parking.
When the vehicle is shifted out of REVERSE (R) and a
five
-second delay has occurred, the passenger's mirror
will return to its original position.
If further adjustment is needed after the mirror is tilted,
the mirror switch may be used.
This feature can be enabled/disabled through the
Driver Information Center. See ªVehicle Programming
and Personalization Featuresº in the Index for
more information.