trunk CADILLAC DTS 2010 1.G User Guide
[x] Cancel search | Manufacturer: CADILLAC, Model Year: 2010, Model line: DTS, Model: CADILLAC DTS 2010 1.GPages: 480, PDF Size: 17.56 MB
Page 127 of 480

— (On):Press this side of the button to turn the lockoutfeature on. When the lockout feature is turned on, thetrunk cannot be unlocked with the keyless entrytransmitter or the trunk release button located near theheadlamp switch on the instrument panel.
If the valet lockout feature is on it will also disable theUniversal Home Remote transmitter, if equipped.
Locking the glove box with your key will also help tosecure your vehicle.
SeeRemote Keyless Entry (RKE) System Operation onpage 3-4andTrunk on page 3-12for additionalinformation.
Content Theft-Deterrent
The security light islocated on the instrumentpanel cluster.
To arm the system:
1. Open the door.
2. Lock the door using the power door lock switch withthe door open or the Remote Keyless Entry (RKE)transmitter. The security light will flash.
3. Close all the doors. The security light will come onand stay on for approximately 30 seconds.
If a door or the trunk is opened without a key or aRKE transmitter the horn will sound and the lamps willflash for about 30 seconds.
3-19
Page 128 of 480

The theft-deterrent system will not arm if you lock thedoors with a key or use the manual door lock. Itarms only if you use a power door lock with the dooropen or the RKE transmitter.
To avoid arming the alarm by accident:
•Lock the vehicle with the door key or the manual
door lock.
•Always unlock a door with a key or use the
RKE transmitter system. Pressing the unlock buttonon the RKE transmitter, or unlocking a door withthe key disarms the content theft-deterrent system.Unlocking a door any other way will activate thealarm when a door or the trunk is opened.
If you activate the alarm by accident, unlock the driver’sdoor with your key. You can also turn off the alarmby using the unlock button on the RKE transmittersystem, or by starting the car with a valid key.
Changes or modifications made to this system by otherthan an authorized service facility could voidauthorization to use the theft system.
Testing the Alarm
1. From inside the vehicle, roll down the window, thenget out of the vehicle, keeping the door open.
2. From outside of the vehicle, with the door open,lock the vehicle using the power door lock or theRKE system and close the door. Wait 30 secondsuntil the security lamp goes off.
3. Reach in and unlock the door using the manuallock and open the door. The horn will sound andthe hazard lights will flash.
You can turn off the alarm by unlocking the driver’s doorwith your key, using the unlock button on the RKEtransmitter or by starting the car with a valid key.
If the alarm does not sound when it should, check tosee if the horn works. The horn fuse may be blown. Toreplace the fuse, seeFuses and Circuit Breakers onpage 6-101. If the fuse does not need to be replaced,you may need to have your vehicle serviced.
To reduce the possibility of theft, always arm thetheft-deterrent system when leaving your vehicle.
3-20
Page 149 of 480

The front display is located on top of the instrumentpanel to the right of the driver. The front display will haveeither three or six lights to provide distance andsystem information. With Adaptive Cruise control (ACC),it will have three lights along with the ACC lights.Without ACC, it will have six lights. High-toned beepsfrom the front speakers are for objects detected near thefront bumper.
The rear display is located near the rear window andcan be seen by looking over your right shoulder.The rear display uses three color-coded lights to providedistance and system information. Low-toned beepsfrom the rear speakers are for the rear bumper.
How the System Works
UFRPA comes on automatically when the shift lever ismoved out of P (Park). The system does not work at aforward or reverse speed greater than 5 mph (8 km/h).
To be detected, objects must be at least 25.4 cm (10 in.)off the ground and below hood or trunk level. Objectsmust also be within 1.2 m (4 ft.) in front of thevehicle and 2.5 m (8 ft.) from the rear bumper. Thisdistance may be less during warmer or humid weather.
When backing up, if objects are detected at thesame time near both the front and rear bumpers, bothcolor-coded light displays will notify you of objects closeto each bumper. If there are objects detected nearboth bumpers, the beeps will only be sounded to notifythat objects are close to the rear bumper. However,if while the vehicle is backing up and an object comeswithin 0.3 m (1 ft.) of the front bumper, and at the sametime there is another object further than 0.3 m (1 ft.)from the rear bumper, then the beeps will only besounded to notify you of the closer object that is nearthe front bumper.
The system can be disabled using the Driver InformationCenter (DIC). See “Parking Assist” underDIC Operationand Displays on page 4-62for more information.
Front Parking AssistDisplay
Rear Parking AssistDisplay
3-41
Page 151 of 480

When the System Does Not Seem to
Work Properly
If the URPA system will not activate due to a temporarycondition, the message PARK ASSIST OFF will bedisplayed on the DIC and a red light will be shown onthe rear URPA display when the shift lever is moved intoR (Reverse). This occurs under the following conditions:
•The driver disables the system.
•The ultrasonic sensors are not clean. Keep the
vehicle’s rear bumper free of mud, dirt, snow,ice and slush. For cleaning instructions, seeWashing Your Vehicle on page 6-95.
•A trailer was attached to the vehicle, or a bicycle or
an object was hanging out of the trunk during thelast drive cycle, the red light may illuminate inthe rear display. Once the attached object isremoved, URPA will return to normal operation.
•A tow bar is attached to the vehicle.
•The vehicle’s bumper is damaged. Take the vehicle
to your dealer/retailer to repair the system.
•Other conditions may affect system performance,
such as vibrations from a jackhammer or thecompression of air brakes on a very large truck.
If the system is still disabled after driving forward atleast 25 km/h (15 mph), take the vehicle to yourdealer/retailer.
Side Blind Zone Alert (SBZA)
The vehicle may have a Side Blind Zone Alert (SBZA)system. Read this entire section before using the system.
{WARNING:
SBZA is only a lane changing aid and does not
replace driver vision. SBZA does not detect:
•Vehicles outside the side blind zones which
may be rapidly approaching.
•Pedestrians, bicyclists, or animals.
Failure to use proper care when changing lanesmay result in damage to the vehicle, injury, ordeath. Always check the outside and rearviewmirrors, glance over your shoulder, and use theturn signal before changing lanes.
When the system detects a vehicle in the side blindzone, amber SBZA displays will light up in the sidemirrors. This indicates that it may be unsafe to changelanes. Before making a lane change, always checkthe SBZA display, check the outside and rearviewmirrors, look over your shoulder for vehicles andhazards, and use the turn signal.
3-43
Page 199 of 480

Electric Power Management
The vehicle has Electric Power Management (EPM) thatestimates the battery’s temperature and state ofcharge. It then adjusts the voltage for best performanceand extended life of the battery.
When the battery’s state of charge is low, the voltage israised slightly to quickly bring the charge back up.When the state of charge is high, the voltage is loweredslightly to prevent overcharging. If the vehicle has avoltmeter gage or a voltage display on the DriverInformation Center (DIC), you may see the voltage moveup or down. This is normal. If there is a problem, analert will be displayed.
The battery can be discharged at idle if the electricalloads are very high. This is true for all vehicles. This isbecause the generator (alternator) may not bespinning fast enough at idle to produce all the powerthat is needed for very high electrical loads.
A high electrical load occurs when several of thefollowing are on, such as: headlamps, high beams, foglamps, rear window defogger, climate control fan athigh speed, heated seats, engine cooling fans, trailerloads, and loads plugged into accessory power outlets.
EPM works to prevent excessive discharge of thebattery. It does this by balancing the generator’s outputand the vehicle’s electrical needs. It can increase
engine idle speed to generate more power, wheneverneeded. It can temporarily reduce the power demands ofsome accessories.
Normally, these actions occur in steps or levels, withoutbeing noticeable. In rare cases at the highest levelsof corrective action, this action may be noticeable to thedriver. If so, a Driver Information Center (DIC)message might be displayed, such as BATTERYSAVER ACTIVE, BATTERY VOLTAGE LOW, orLOW BATTERY. If this message is displayed, it isrecommended that the driver reduce the electrical loadsas much as possible. SeeDIC Warnings and Messageson page 4-67.
Inadvertent Power Battery Saver
This feature is designed to protect your vehicle’s batteryagainst drainage from the interior lamps, trunk lamp,glove box lamp, or the garage door opener. When theignition is turned off, the power to these features willautomatically turn off after 10 minutes. Power willbe restored for an additional 10 minutes if any door ortrunk is opened, or the courtesy lamp switch isturned on.
4-33
Page 200 of 480

Battery Run-Down Protection
This feature helps prevent the battery from beingdrained, if the interior courtesy lamps, reading/maplamps, visor vanity lamps or trunk lamp are accidentallyleft on. If any of these lamps are left on, theyautomatically turn off after 10 minutes, if the ignition isoff. The lamps will not come back on again untilone of the following occurs:
•The ignition is turned on.
•The exterior lamps control is turned off, then on
again.
The headlamps will timeout after 10 minutes, if they aremanually turned on with the ignition on or off.
Accessory Power Outlet(s)
The accessory power outlets can be used to plug inelectrical equipment, such as a cellular telephone.
If the vehicle has a center console, the power outlet islocated inside the lower storage area. Some vehiclesmay have an outlet on the right front lower part ofthe driver’s seat and under the climate control systemnext to the ashtray. SeeCenter Console Storageon page 3-55.
There are two accessory power outlets in the rear seatarea located on the door armrests next to theashtrays.
There may be a small cap that must be removed toaccess the accessory power outlet. When not using theoutlet be sure to cover it with the protective cap.
The accessory power outlet can be used at any time.
Notice:Leaving electrical equipment plugged in foran extended period of time while the vehicle is offwill drain the battery. Power is always suppliedto the outlets. Always unplug electrical equipmentwhen not in use and do not plug in equipmentthat exceeds the maximum 20 ampere rating.
Certain accessory power plugs may not be compatibleto the accessory power outlet and could result inblown vehicle or adapter fuses. If you experience aproblem see your dealer/retailer for additionalinformation on the accessory power outlets.
Notice:Adding any electrical equipment to thevehicle can damage it or keep other componentsfrom working as they should. The repairs would notbe covered by the vehicle warranty. Do not useequipment exceeding maximum amperage rating of20 amperes. Check with your dealer/retailer beforeadding electrical equipment.
4-34
Page 245 of 480

TRACTION CONTROL ON
This message displays when the Traction ControlSystem (TCS) is turned on. SeeTraction Control System(TCS) on page 5-6for more information.
TRANSMISSION HOT IDLE ENGINE
Notice:If you drive your vehicle while thetransmission fluid is overheating and thetransmission temperature warning is displayed onthe instrument panel cluster and/or DIC, youcan damage the transmission. This could lead tocostly repairs that would not be covered byyour warranty. Do not drive your vehicle withoverheated transmission fluid or while thetransmission temperature warning is displayed.
This message displays when the transmission fluid inyour vehicle is too hot. Stop the vehicle and allowit to idle until the transmission cools down or until thismessage is removed.
TRUNK OPEN
This symbol appears withthis message.
This message displays when the trunk is not closedcompletely. Make sure that the trunk is closedcompletely.
TURN SIGNAL ON
This message displays as a reminder to turn off the turnsignal if you drive your vehicle for more than about1 mile (1.6 km) with a turn signal on. A multiple chimesounds when this message is displayed.
4-79
Page 311 of 480

Notice:Overloading the vehicle may causedamage. Repairs would not be covered by thevehicle warranty. Do not overload the vehicle.
If you put things inside your vehicle, likesuitcases, tools, packages, or anything else, theywill go as fast as the vehicle goes. If you haveto stop or turn quickly, or if there is a crash, theywill keep going.
{WARNING:
Things you put inside your vehicle can strikeand injure people in a sudden stop or turn, orin a crash.
•Put things in the trunk of your vehicle. In
a trunk, put them as far forward as youcan. Try to spread the weight evenly.
•Never stack heavier things, like
suitcases, inside the vehicle so that someof them are above the tops of the seats.
•Do not leave an unsecured child restraint
in your vehicle.
•When you carry something inside the
vehicle, secure it whenever you can.
Automatic Level Control
This feature keeps the rear of your vehicle levelas the load changes. It is automatic, you donot need to adjust anything.
This type of level control is fully automatic and willprovide a better leveled riding position as well asbetter handling under a variety of passenger andloading conditions. An air compressor connected tothe rear shocks will raise or lower the rear of thevehicle to maintain proper vehicle height. Thesystem is activated when the ignition key is turnedto ON/RUN and will automatically adjust vehicleheight thereafter. The system may exhaust(lower vehicle height) for up to ten minutes afterthe ignition key has been turned to LOCK/OFF.You may hear the air compressor operating whenthe height is being adjusted.
5-23
Page 330 of 480

Filling a Portable Fuel Container
{WARNING:
Never fill a portable fuel container while it is in the
vehicle. Static electricity discharge from the
container can ignite the fuel vapor. You can be
badly burned and the vehicle damaged if this
occurs. To help avoid injury to you and others:
•Dispense fuel only into approved containers.
•Do not fill a container while it is inside a
vehicle, in a vehicle’s trunk, pickup bed, or onany surface other than the ground.
•Bring the fill nozzle in contact with the inside
of the fill opening before operating the nozzle.Contact should be maintained until the fillingis complete.
•Do not smoke while pumping fuel.
•Do not use a cellular phone while
pumping fuel.
Checking Things Under
the Hood
{WARNING:
An electric fan under the hood can start up and
injure you even when the engine is not running.
Keep hands, clothing, and tools away from any
underhood electric fan.
{WARNING:
Things that burn can get on hot engine parts and
start a fire. These include liquids like fuel, oil,
coolant, brake fluid, windshield washer and other
fluids, and plastic or rubber. You or others could
be burned. Be careful not to drop or spill things
that will burn onto a hot engine.
6-10
Page 399 of 480

Tire Sealant and Compressor
Kit Storage
The tire sealant and compressor kit is located inthe trunk.
1. Open the trunk. SeeTrunk on page 3-12.
2. Lift the cover.
3. Turn the retainer clockwise and remove the tiresealant and compressor kit.
To store the tire sealant and compressor kit, reversethe steps.
6-79