steering wheel CADILLAC DTS 2010 1.G Owner's Guide

The cruise control buttonsare located on left side ofthe steering wheel.
I(On):Turns on the cruise control system.
+ RES (Resume/Accelerate):Press to make thevehicle accelerate or resume to a previously set speed.
SET– (Set):Press to set the speed.
[(Cancel):Press to cancel cruise control.
Cruise control will not work if the parking brake is set, orif the master cylinder brake fluid level is low.
If the brakes are applied, the cruise control shuts off.
The cruise light on the instrument panel cluster comeson after the cruise control has been set to the desiredspeed.
1. PressI.
2. Get up to the desired speed.
3. Press the SET– button located on the steeringwheel and release it.
4. Take your foot off the accelerator.
Resuming a Set Speed
Suppose the cruise control is set at a desired speedand then the brakes are applied. This shuts off thecruise control. But it does not need to be reset.
Once the vehicle is traveling approximately 40 km/h(25 mph) or more, press the +RES (resume/accelerate)button to return to the desired preset speed. Thecruise light displays again.
The vehicle returns to and stays at the preset speed. Ifyou press and hold the +RES button, the vehicle speedincreases until the button is released or the brake isapplied. Do not hold in the +RES button, if you do notwant the vehicle speed to increase.
4-13

Using Cruise Control on Hills
How well your cruise control works on hills dependsupon the vehicle speed, load, and the steepness of thehills. When going up steep hills, you might have tostep on the accelerator pedal to maintain the vehicle’sspeed. When going downhill, you might have to brake orshift to a lower gear to keep the vehicle’s speeddown. Applying the brake or shifting into a lower gearends cruise control. If you need to apply the brakeor shift to a lower gear due to the grade of the downhillslope, you might not want to attempt to use thecruise control feature.
Ending Cruise Control
To turn off the cruise control, step lightly on the brakepedal, or press the cancel button on the steering wheel.
Erasing Speed Memory
The cruise control set speed memory is erased whenthe cruise control or the ignition is turned off.
Adaptive Cruise Control
For vehicles with this feature, be sure to read this entiresection before using it.
The system operates on a radio frequency subject toFederal Communications Commission (FCC) Rules andwith Industry Canada.
This device complies with Part 15 of the FCC Rules.Operation is subject to the following two conditions:
1. This device may not cause interference.
2. This device must accept any interference received,including interference that may cause undesiredoperation of the device.
This device complies with RSS-210 of Industry Canada.Operation is subject to the following two conditions:
1. This device may not cause interference.
2. This device must accept any interference received,including interference that may cause undesiredoperation of the device.
Changes or modifications to this system by other thanan authorized service facility could void authorization touse this equipment.
Adaptive Cruise Control (ACC) is an enhancement totraditional cruise control. It allows you to keep cruisecontrol engaged in moderate traffic conditions withouthaving to constantly reset your cruise control.ACC uses radar to detect a vehicle directly ahead inyour path, within a distance of 100 m (330 ft), andoperates at speeds above 40 km/h (25 mph). When it isengaged by the driver, the system can apply limitedbraking or acceleration of the vehicle automatically tomaintain a selected follow distance to the vehicle ahead.Braking is limited to 2.45 m/sec2 (0.25 g’s) ofdeceleration, which is comparable to moderate
4-15

WARNING: (Continued)
•When weather limits visibility, such as when in
fog, rain, or snow conditions, Adaptive CruiseControl performance is limited. There may notbe enough distance to adapt to the changingtraffic conditions. Do not use cruise controlwhen visibility is low.
The ACCs are located on the steering wheel.
The cruise control buttons are located on left side of thesteering wheel.
](On):Press to turn the system on.
+ Res (Resume/Accelerate):Press to make thevehicle resume to a previously set speed or to increasethe set speed when ACC is already active.
Set–:Press to set the speed or to decrease the setspeed when ACC is already active.
[(Cancel):Press to cancel ACC.
+GAP (Increase Following Distance):Press toincrease the distance between your vehicle and othervehicles.
!GAP (Decrease Following Distance):Press todecrease the distance between your vehicle and othervehicles.
ACC will not work if the master cylinder brake fluid levelis low.
4-17

Your vehicle will not reach the set speed until thesystem determines there is not a vehicle in front of you.At that point, your vehicle speed will increase to theset speed.
Decreasing Set Speed While Using ACC
Press the SET– button until you reach the lower speeddesired, then release it.
To slow down in very small amounts, briefly press theSET– button. Each time this is done, the set speeddecreases by 1 km/h (1 mph) slower.
Resuming a Set Speed
Suppose the ACC is set at a desired speed and thenthe brakes are applied. This will turn off the ACC. But itdoes not need to be reset.
Once the vehicle speed reaches about 40 km/h (25 mph)or more, press the +RES button. ACC will be engagedwith the previously chosen set speed.
Selecting the Follow Distance (GAP)
When the system detects a slower moving vehicle, it willadjust your vehicle’s speed and maintain the followdistance (gap) you select.
Use the plus and minus buttons on the steering wheelto adjust the follow distance.
Press the plus button to increase the distance or theminus button to decrease the distance. The first buttonpress shows the current follow distance setting onthe DIC. The current follow distance setting willbe maintained until it is changed.
There are six follow distances to choose from. Thefollow distance selection ranges from near to far(one second to two seconds follow time). The distancemaintained for a selected follow distance will varybased on vehicle speed. The faster the vehicle speedthe further back your vehicle will follow. Considertraffic and weather conditions when selecting the followdistance. The range of selectable distances may notbe appropriate for all drivers and driving conditions.If you prefer to travel at a follow distance farther thanACC allows, disengage the system and drive manually.
4-19

Erasing Set Speed Memory
Press the ACC button or turn the ignition off.
Other Messages
There are three additional messages that may appearon the DIC. They are SERVICE RADAR CRUISE,RADAR CRUISE NOT READY and CLEAN RADAR.These messages will appear to indicate a problem withthe ACC. SeeDIC Warnings and Messages onpage 4-67for more information.
Cleaning the System
The radar can become blocked by snow, ice, or dirt.If so, you may need to turn off the engine and clean thelens. Remember, do not use ACC in icy conditions,or when visibility is low, such as in fog, rain or snow.
The emblem/lens is located in the center of the grille.
To clean the emblem/lens, wipe the surface with asoft cloth. After cleaning the emblem/lens, try to engagethe ACC. If you are unable to do so, see yourdealer/retailer.
Exterior Lamps
The exterior lamps controlis located on the instrumentpanel to the left of thesteering wheel.
It controls the following systems:
•Headlamps
•Taillamps
•Parking Lamps
•License Plate Lamps
•Instrument Panel Lights
•Fog Lamps
The exterior lamps control has four positions:
O(Off):Turns off the exterior lamps except for
Daytime Running Lamps (DRL).
4-25

There is also an interiortemperature sensorlocated next to the steeringwheel that measures thetemperature of the airinside the vehicle.
There is also an exterior temperature sensor locatedbehind the front grille. This sensor reads the outside airtemperature and helps maintain the temperatureinside the vehicle. Any cover on the front of the vehiclecould cause a false reading in the displayedtemperature.
In order to prevent false temperature readings atstartup, the displayed temperature will not change untilthe following occurs:
•Vehicle speed is above 16 km/h (10 mph) for
5 minutes.
•Vehicle speed is above 51 km/h (32 mph) for 2 and
a half minutes.
The climate control system uses the information fromthese sensors to maintain your comfort setting byadjusting the outlet temperature, fan speed, and the airdelivery mode. The system may also supply coolerair to the side of the vehicle facing the sun. Therecirculation mode will also be used as needed tomaintain cool outlet temperatures.
Outlet Adjustment
For the front outlets, use the thumbwheel located beloweach outlet to change the direction of the airflow. Use thethumbwheel located next to the outlets to shut the airflowor to open the outlets and re-direct the air.
For the rear outlets, slide the lever left or right and up ordown to change the direction of the airflow.
Operation Tips
•Clear away any ice, snow or leaves from the air
inlets at the base of the windshield that mayblock the flow of air into your vehicle.
•Use of non-GM approved hood deflectors may
adversely affect the performance of the system.
•Keep the path under the front seats clear of objects
to help circulate the air inside of your vehicle moreeffectively.
4-41

Highbeam On Light
This light comes on whenthe high-beam headlampsare in use.
SeeHeadlamp High/Low-Beam Changer on page 4-6for more information.
Fuel Gage
The fuel gage showsapproximately how muchfuel is in the tank. Itworks only when theengine is on.
An arrow on the fuel gage indicates the side of thevehicle the fuel door is on.
If the fuel supply gets low, the FUEL LEVEL LOWmessage appears in the Driver Information Center anda single chime sounds. SeeDIC Warnings andMessages on page 4-67for more information.
Here are a few situations that may occur with the fuelgage. All of these situations are normal and do notindicate that anything is wrong with the fuel gage:
•At the gas station the gas pump shuts off before the
gage reads full.
•The gage may change when the vehicle is turning,
stops quickly or accelerates quickly.
•It takes a little more or less fuel to fill the tank than
the gage indicated. For example, the gage mayhave indicated that the tank was half full, butit actually took a little more or less than half thetank’s capacity to fill the tank.
Driver Information Center (DIC)
The Driver Information Center (DIC) gives you thestatus of many of your vehicle’s systems. The DIC isalso used to display warning/status messages. Allmessages will appear in the DIC display located at thebottom of the instrument panel cluster, below thetachometer and speedometer. The DIC buttons arelocated on the instrument panel, to the left of thesteering wheel.
4-61

The DIC comes on when the ignition is on. After a shortdelay, the DIC will display the information that waslast displayed before the engine was turned off.
The top line of the DIC display shows the vehicle systeminformation and the warning/status messages. Thebottom line of the DIC display shows the odometer onthe left side. The bottom line of the DIC display alsoshows a digital speedometer on the right side.
If a problem is detected, a warning message will appearon the display. Be sure to take any message thatappears on the display seriously and remember thatclearing the message will only make the messagedisappear, not correct the problem.
DIC Operation and Displays
The Driver InformationCenter (DIC) has differentdisplays which can beaccessed by pressing theDIC buttons located onthe instrument panel, to theleft of the steering wheel.
3Trip/Fuel:Press this button to scroll through the
trip and fuel displays. See “Trip/Fuel Display MenuItems” following for more information on these displays.
TVehicle Information:Press this button to scroll
through the vehicle information displays. See “VehicleInformation Display Menu Items” following for moreinformation on these displays.
UCustomization:Press this button to scroll through
each of the customization features. SeeDIC VehicleCustomization on page 4-80for more information on thecustomization features.
VSet/Reset:Press this button to reset certain DIC
features and to acknowledge DIC warning messagesand clear them from the DIC display.
yzMenu Up/Down:Press this button to scroll up
and down the menu items.
4-62

CHIME VOLUME
This feature allows you to select the volume level of thechime.
Press the customization button until CHIME VOLUMEappears on the DIC display. Press the set/reset buttononce to access the settings for this feature. Then pressthe menu up/down button to scroll through the followingsettings:
NORMAL:The chime volume will be set to anormal level.
LOUD:The chime volume will be set to a loud level.
NO CHANGE:No change will be made to this feature.The current setting will remain.
There is no default for chime volume. The volume willstay at the last known setting.
To select a setting, press the set/reset button while thedesired setting is displayed on the DIC.
PARK TILT MIRRORS
If your vehicle has this feature, it allows you to selectwhether or not the outside mirror(s) will automatically tiltdown when the vehicle is shifted into R (Reverse).SeePark Tilt Mirrors on page 3-39for more information.
Press the customization button until PARK TILTMIRRORS appears on the DIC display. Press theset/reset button once to access the settings forthis feature. Then press the menu up/down button toscroll through the following settings:
OFF (default):Neither outside mirror will be tilted downwhen the vehicle is shifted into R (Reverse).
DRIVER MIRROR:The driver’s outside mirror will betilted down when the vehicle is shifted into R (Reverse).
PASSENGER MIRROR:The passenger’s outsidemirror will be tilted down when the vehicle is shifted intoR (Reverse).
BOTH MIRRORS:The driver’s and passenger’s outsidemirrors will be tilted down when the vehicle is shiftedinto R (Reverse).
NO CHANGE:No change will be made to this feature.The current setting will remain.
To select a setting, press the set/reset button while thedesired setting is displayed on the DIC.
EASY EXIT RECALL
If your vehicle has this feature, it allows you to selectyour preference for the automatic easy exit seat feature.SeeMemory Seat, Mirrors and Steering Wheel onpage 2-6for more information.
4-85

Press the customization button until EASY EXITRECALL appears on the DIC display. Press the set/resetbutton once to access the settings for this feature.Then press the menu up/down button to scroll throughthe following settings:
DOOR BUTTON ONLY:No automatic seat exit recallwill occur. The recall will only occur after pressingthe easy exit seat button.
BUTTON AND KEY OUT (default):If the features areenabled through the EASY EXIT SETUP menu, thedriver’s seat will move back, and if the vehicle has thepower tilt wheel and telescopic steering feature, thepower steering column will move up and forward whenthe key is removed from the ignition or after pressingthe easy exit seat button.
The automatic easy exit seat movement will only occurone time after the key is removed from the ignition.If the automatic movement has already occurred, andyou put the key back in the ignition and remove it again,the seat and steering column will stay in the originalexit position, unless a memory recall took place prior toremoving the key again.
NO CHANGE:No change will be made to this feature.The current setting will remain.
To select a setting, press the set/reset button while thedesired setting is displayed on the DIC.
EASY EXIT SETUP
If your vehicle has this feature, it allows you to selectwhich areas will recall with the automatic easy exit seatfeature. It also allows you to turn off the automaticeasy exit feature. SeeMemory Seat, Mirrors andSteering Wheel on page 2-6and “EASY EXIT RECALL”earlier for more information.
Press the customization button until EASY EXIT SETUPappears on the DIC display. Press the set/reset buttononce to access the settings for this feature. Thenpress the menu up/down button to scroll through thefollowing settings:
OFF:No automatic seat exit will recall.
SEAT ONLY:The driver’s seat will recall.
TILT ONLY:The steering wheel tilt feature will recall.
TELESCOPE ONLY:The steering column telescopefeature will recall.
SEAT/TILT:The driver’s seat and the steering wheel tiltfeature will recall.
SEAT/TELESCOPE:The driver’s seat and the steeringcolumn telescope feature will recall.
TILT/TELESCOPE:The steering wheel tilt and steeringcolumn telescope features will recall.
4-86