mirror CADILLAC DTS 2011 1.G User Guide

Black plate (5,1)Cadillac DTS Owner Manual - 2011
Q(Lock):Press to lock all the doors. If enabled
through the Driver Information Center (DIC), the parking
lamps may flash once to indicate locking has occurred.
The horn may chirp when
Qis pressed again within
five seconds. See DIC Vehicle Customization
on
page 4‑77for additional information.
Pressing
Qmay arm the content theft-deterrent system.
See Content Theft-Deterrent on page 3‑19.
K(Unlock): Press once to unlock the driver door.
If
Kis pressed again within five seconds, all remaining
doors unlock. The interior lamps come on and stay
on for 20 seconds or until the ignition is turned on.
If enabled through the DIC, the parking lamps flash
twice to indicate unlocking has occurred. See DIC
Vehicle Customization
on page 4‑77. PressingKmay
disarm the content theft-deterrent system. See Content
Theft-Deterrent on page 3‑19.
V(Remote Trunk Release): Press and hold for
about one second to unlock the trunk. The transmission
must be in P (Park).
L(Vehicle Locator/Panic Alarm): Press and release
to locate the vehicle. The turn signal lamps flash and
the horn sounds three times.
Press and hold
Lfor more than two seconds to
activate the panic alarm. The turn signal lamps flash
and the horn sounds repeatedly for 30 seconds.
The alarm turns off when the ignition is moved to
ON/RUN or
Lis pressed again. The ignition must be
in LOCK/OFF for the panic alarm to work.
The vehicle comes with two transmitters. Each
transmitter will have a number on top of it, “1”or“2”.
These numbers correspond to the driver of the vehicle.
For example, the memory seat position for driver 1 will
be recalled when using the transmitter labeled “1”,
if enabled through the DIC. See Memory Seat, Mirrors
and Steering Wheel
on page 2‑6and DIC Vehicle
Customizationon page 4‑77for more information.
3-5

Black plate (17,1)Cadillac DTS Owner Manual - 2011
Programming the Power Windows
If the battery on the vehicle has been recharged,
disconnected, or is not working, you will need to
reprogram each front power window for the express-up
feature to work. Before reprogramming, replace or
recharge the vehicle's battery.
To program each front window, follow these steps:1. With the ignition in ACC/ACCESSORY, ON/RUN, or when Retained Accessory Power (RAP) is
active, close all doors.
2. Press and hold the power window switch until the window is fully open.
3. Pull the power window switch up until the window is fully closed.
4. Continue holding the switch up for approximately two seconds after the window is completely closed.
The window is now reprogrammed. Repeat the process
for the other windows.
Window Lockout
o (Window Lockout): The rear window lockout button
is located on the driver door near the window switches.
Press the right side of the button to disable the rear
window controls. The light on the button will illuminate,
indicating the feature is in use. The rear windows still
can be raised or lowered using the driver window
switches when the lockout feature is active.
To restore power to the rear windows, press the button
again. The light on the button will go out.
Sun Visors
Swing down the visor to block out glare. The visors also
have side-to-side slide capability.
Lighted Visor Vanity Mirror
Pull the visor down and lift the cover to view the mirror.
The light will come on when the cover is opened. It will
go out when you close the cover. If your vehicle has the
adjustable lighting feature, slide the switch up or down
to brighten or dim the light.
3-17

Black plate (35,1)Cadillac DTS Owner Manual - 2011
Mirrors
Automatic Dimming Rearview Mirror
The vehicle has an automatic dimming inside rearview
mirror with a compass display. Automatic dimming
reduces the glare of lights from behind the vehicle.
The dimming feature comes on and the indicator light
illuminates each time the vehicle is started.
O(On/Off):Press and holdOfor about three seconds
to turn the dimming feature and compass display on
or off.
AUTO 3(Vehicles with Intellibeam®):Press
and hold for approximately three seconds to turn the
compass display on or off. See Exterior Lamps
on
page 4‑25for more information.
Cleaning the Mirror
Do not spray glass cleaner directly on the mirror. Use a
soft towel dampened with water.
Compass
Compass Operation
PressOorAUTO 3, depending on the vehicle, to
turn the compass on or off.
When the ignition and the compass feature are on, after
a few seconds, the mirror will display the compass
heading. The compass automatically calibrates as the
vehicle is driven.
Compass Calibration
If after a few seconds, the display does not show the
correct direction, (for example, N for North), there may
be a strong magnetic field interfering with the compass.
Interference can be caused by a magnetic antenna
mount, magnetic note pad holder or a similar
magnetic item.
The compass can be placed in calibration mode
manually by pressing and holding
OorAUTO 3,
depending on the vehicle, until a C is shown in the
compass display.
The compass can be calibrated by driving the vehicle in
circles at 5 mph (8 km/h) or less until the display reads a
direction.
3-35

Black plate (36,1)Cadillac DTS Owner Manual - 2011
Compass Variance
The compass is set to zone eight. If you do not live
in zone eight or drive out of the area, the compass
variance needs to be changed to the appropriate zone.
To adjust for compass variance:1. Find the current location and variance zone number on the following zone map.
2. Press and holdOorAUTO 3until a zone
number displays. 3. Once the zone number displays, press
Oor
AUTO
3repeatedly until the correct zone
number displays. Stop pressing the button and the
mirror will return to normal operation. If C appears
in the compass window, the compass may need
calibration. See “Compass Calibration” listed
previously.
Outside Power Foldaway Mirrors
Controls for the outside
power mirrors are located
on the driver door
armrest.
Press the selector switch (A) or (B) to choose either the
left or right outside mirror. Then press the control pad to
move the mirror to the desired direction.
3-36

Black plate (37,1)Cadillac DTS Owner Manual - 2011
Mirror Adjustment
1. Press (C) to unfold the mirrors out to the drivingposition.
2. Press (D) to fold the mirrors toward the vehicle.
Resetting the Power Foldaway Mirrors
Reset the power foldaway mirrors if:
.The mirrors are accidentally obstructed while
folding.
.They are accidentally manually folded/unfolded.
.The mirrors do not stay in the unfolded position.
.The mirrors vibrate at normal driving speeds.
Fold and unfold the mirrors one time using the mirror
controls to reset them to their normal position. A noise
may be heard during the resetting of the power
foldaway mirrors. This sound is normal after a manual
folding operation.
Turn Signal Indicator (If Equipped)
The vehicle may have a turn signal indicator lamp that
is built into the mirror. The turn signal lamp flashes with
the use of the vehicle's turn signal and hazard flashers.
Outside Automatic Dimming Mirror
If the vehicle has this feature, the driver side mirror
adjusts for the glare of headlamps behind you. This
feature is controlled by the on and off settings on the
automatic dimming rearview mirror.
Side Blind Zone Alert (SBZA)
If the vehicle has the Side Blind Zone Alert (SBZA)
system, see Side Blind Zone Alert (SBZA)on
page 3‑42for more information.
Park Tilt Mirrors
If your vehicle is equipped with memory mirrors, it is
capable of performing the park tilt mirror feature. This
feature allows the driver and passenger side mirror to
tilt to a factory programmed position when the vehicle is
in R (Reverse). This feature may be useful in allowing
you to view the curb when you are parallel parking.
When the vehicle is shifted out of R (Reverse) and
either a five-second delay has occurred, or the ignition
is turned to LOCK/OFF, the driver and passenger side
mirror will return to its original position.
This feature can be enabled/disabled through the
Driver Information Center (DIC). See DIC Vehicle
Customization
on page 4‑77for more information.
3-37

Black plate (38,1)Cadillac DTS Owner Manual - 2011
Outside Convex Mirror
{WARNING:
A convex mirror can make things, like other
vehicles, look farther away than they really are.
If you cut too sharply into the right lane, you could
hit a vehicle on the right. Check the inside mirror
or glance over your shoulder before changing
lanes.
The passenger side mirror is convex shaped. A convex
mirror's surface is curved so more can be seen from the
driver seat.
Outside Heated Mirrors
=(Rear Window Defogger): Press to heat the
mirrors. See “Rear Window Defogger” underDual
Climate Control System
on page 4‑34for more
information.
Object Detection Systems
Ultrasonic Front and Rear Parking
Assist (UFRPA)
For vehicles with the Ultrasonic Front and Rear Parking
Assist (UFRPA) system, it operates at speeds less than
8 km/h (5mph), and assists the driver with parking and
avoiding objects. It can determine how close objects are
to the front bumper, up to 1.2 m (4 ft.) in front of the
vehicle and the rear bumper, up to 2.5 m (8 ft.) behind
the vehicle. The distance sensors are located on the
front and rear bumper.
3-38

Black plate (39,1)Cadillac DTS Owner Manual - 2011
{WARNING:
The Ultrasonic Front and Rear Park Assist
(UFRPA) system does not replace driver vision.
It cannot detect:
.objects that are below the bumper, underneath
the vehicle, or if they are too close or far from
the vehicle
.children, pedestrians, bicyclists, or pets.
If you do not use proper care before moving
forward and while backing; vehicle damage, injury,
or death could occur. Even with UFRPA, always
check in front of the vehicle before moving
forward and behind the vehicle before backing up.
While moving forward and backing, be sure to
look for objects and check the vehicle's mirrors.
Front Parking Assist Display
Rear Parking AssistDisplay
The front display is located on top of the instrument
panel to the right of the driver. The front display will
have either three or six lights to provide distance and
system information. With Adaptive Cruise control (ACC),
it will have three lights along with the ACC lights.
Without ACC, it will have six lights. High-toned beeps
from the front speakers are for objects detected near
the front bumper.
The rear display is located near the rear window and
can be seen by looking over your right shoulder. The
rear display uses three color-coded lights to provide
distance and system information. Low-toned beeps from
the rear speakers are for the rear bumper.
3-39

Black plate (42,1)Cadillac DTS Owner Manual - 2011
Side Blind Zone Alert (SBZA)
The vehicle may have a Side Blind Zone Alert (SBZA)
system. Read this entire section before using the
system.
{WARNING:
SBZA is only a lane changing aid and does not
replace driver vision. SBZA does not detect:
.Vehicles outside the side blind zones which
may be rapidly approaching.
.Pedestrians, bicyclists, or animals.
Failure to use proper care when changing lanes
may result in damage to the vehicle, injury,
or death. Always check the outside and rearview
mirrors, glance over your shoulder, and use the
turn signal before changing lanes.
When the system detects a vehicle in the side blind
zone, amber SBZA displays will light up in the side
mirrors. This indicates that it may be unsafe to change
lanes. Before making a lane change, always check the SBZA display, check the outside and rearview mirrors,
look over your shoulder for vehicles and hazards, and
use the turn signal.
SBZA Detection Zones
The SBZA sensor covers a zone of approximately
one lane over from both sides of the vehicle, 3.5 m
(11 ft). This zone starts at each side mirror and goes
back approximately 5 m (16 ft). The height of the zone is
approximately between 0.5 m (1.5 ft) and 2.0 m (6 ft) off
the ground.
3-42

Black plate (43,1)Cadillac DTS Owner Manual - 2011
The SBZA detection zones do not change if the vehicle
is towing a trailer. So be extra careful when changing
lanes while towing a trailer.
How the System Works
Left Side Mirror DisplayRight Side Mirror Display
When the vehicle is started, both outside mirror displays
will briefly come on to indicate that the system is
operating. While driving forward, the left or right side
mirror SBZA display will light up if a vehicle is detected
in that blind zone. If you activate a turn signal and a
vehicle has been detected on the same side, the SBZA
display will flash to give you extra warning not to
change lanes.
SBZA displays do not come on while the vehicle is
approaching or passing other vehicles. At speeds
greater then 20 mph (32 km/h), SBZA displays may
come on when a vehicle you have passed remains in or
drops back into the detection zone. SBZA can be disabled through the Driver Information
Center (DIC). See
Driver Information Center (DIC)
on
page 4‑59for more information. If the SBZA is disabled
by the driver, the SBZA mirror displays will not light up
during normal driving.
When the System Does Not Seem To Work
Properly
Occasional missed alerts can occur under normal
circumstances and will increase in wet conditions.
The system does not need to be serviced due to an
occasional missed alert. The number of missed alerts
will increase with increased rainfall or road spray.
If the SBZA displays do not light up when the system is
on and vehicles are in the blind zone, the system may
need service. Take the vehicle to your dealer.
SBZA is designed to ignore stationary objects; however,
the system may occasionally light up due to guard rails,
signs, trees, shrubs, and other stationary objects. This
is normal system operation, the vehicle does not need
service.
SBZA does not operate when the left or right corners of
the rear bumper are covered with mud, dirt, snow, ice,
slush, or in heavy rainstorms. For cleaning instructions,
see Washing Your Vehicle
on page 6‑98. If the DIC
still displays the SIDE BLIND ZONE SYSTEM
UNAVAILABLE message after cleaning the bumper,
see your dealer.
3-43

Black plate (45,1)Cadillac DTS Owner Manual - 2011
Lane Departure Warning (LDW)
The vehicle may have a Lane Departure Warning
(LDW) system. Read this entire section before using the
system.
{WARNING:
The Lane Departure Warning (LDW) system does
not steer the vehicle and is only an aid to help you
stay in your driving lane. The LDW system
may not:
.Provide you with enough time to avoid a lane
change collision.
.Be loud enough for you to hear the warning
beeps.
.Work properly under bad weather conditions
or if the windshield is not kept clean.
.Detect lane markings and will not detect road
edges.
.Warn you that your vehicle is crossing a lane
marking if the system does not detect the lane
marking.(Continued)
WARNING: (Continued)
LDW will indicate the system is working whenever
it detects either the left or right lane marking. So if
you depart on the side of the lane that LDW is not
detecting, LDW will not warn you.
If you do not carefully maintain your vehicle
position within the lane, vehicle damage, injury,
or death could occur. Even with LDW, always
keep your attention on the road and maintain
proper vehicle position within the lane. Always
keep the windshield clean and do not use LDW in
bad weather conditions.
When the vehicle crosses a detected lane marking, the
LDW symbol will flash and you will hear three beeps.
LDW will not warn you if the turn signal is on or if you
make a sharp maneuver. Before making a lane change,
check the vehicle's mirrors, glance over your shoulder
for vehicles and hazards, and start the turn signal
before changing lanes.
3-45