audio CADILLAC ELDORADO 2002 10.G Owners Manual

iv
Vehicle Damage Warnings
Also, in this book you will find these notices:
NOTICE:
These mean there is something that could damage
your vehicle.
In the notice area, we tell you about something that can
damage your vehicle. Many times, this damage would
not be covered by your warranty, and it could be costly.
But the notice will tell you what to do to help avoid
the damage.
When you read other manuals, you might see
CAUTION and NOTICE warnings in different
colors or in different words.
You'll also see warning labels on your vehicle.
They use the same words, CAUTION or NOTICE.
Vehicle Symbols
Your vehicle may be equipped with components and
labels that use symbols instead of text. Symbols,
used on your vehicle, are shown along with the text
describing the operation or information relating to a
specific component, control, message, gage or indicator.
If you need help figuring out a specific name of a
component, gage or indicator reference the following
topics in the Index:

ªEngine Compartment Overviewº

ªInstrument Panelº

ªComfort Controlsº

ªAudio Systemsº
Also see ªWarning Lights and Gagesº in the Index.

2-20
NOTICE:
If your key seems stuck in LOCK and you can't
turn it, be sure you are using the correct key;
if so, is it all the way in? If it is, then turn the
steering wheel left and right while you turn the
key hard. Turn the key only with your hand.
Using a tool to force it could break the key
or the ignition switch. If none of this works,
then your vehicle needs service.
B (LOCK): Before you put the key in, the ignition
will be in LOCK. This is the only position from
which you can insert or remove the key. This position
locks the ignition, steering wheel and transaxle.
It's a theft
-deterrent feature.
C (OFF): This position lets you turn off the engine
but still turn the steering wheel. It doesn't lock the
steering wheel like LOCK does. Use OFF if you must
have your vehicle in motion while the engine is off
(for example, if your vehicle is being pushed).
D (RUN): This is the position for driving.
E (START): This position starts the engine.
Retained Accessory Power (RAP)
NOTICE:
When using RAP, always leave your key in
LOCK. If you leave your key in any other
position than LOCK, your battery will
discharge prematurely.
The following accessories on your vehicle may be used
for up to 10 minutes after the ignition key is turned
from RUN to OFF, and then to LOCK:

Radio

Power Windows

Audio Steering Wheel Controls

Sunroof (Option)
Power to these accessories stops after 10 minutes or
if either door is opened. If you want power for another
10 minutes, turn the ignition key to RUN, to OFF and
then to LOCK.

2-63
The main components of the instrument panel are the following:
A. Air Outlets
B. Turn Signal/Multifunction Lever
C. Instrument Panel Cluster
D. Radio (Audio System)
E. Driver Information Center Control Buttons
F. Exterior Lamp Controls
G. HVAC Steering Wheel ControlsH. Hood Release
I. Horn
J. Audio Steering Wheel Controls
K. Shift Lever
L. Climate Control System
M. Glove Box

2-77 Security Light
This light works with
the PASS
-Key II system.
See ªPASS
-Key IIº in the
Index for more information.
Fuel Gage
The fuel gage shows
approximately how much
fuel is in the tank. It works
only when the ignition is
in RUN.Here are a few concerns some owners have had about
the fuel gage. All of these situations are normal and do
not indicate that anything is wrong with the fuel gage.

At the gas station the gas pump shuts off before
the gage reads full.

It takes more (or less) gas to fill the tank than the
gage said. For example, the gage read half a tank,
but it took more (or less) than the tank's remaining
capacity to fill it.

The gage may change when you turn, stop or
speed up.
Fuel Data Display
Everything you need to know about the fuel
economy and how far you can travel with your
vehicle's remaining fuel is displayed on the Driver
Information Center (DIC). Fuel data can be
obtained by pressing the SKIP INFO button
located on the instrument panel above the audio
system. See ªDIC Controls and Displaysº later
in this section for more information.

3-
3-1
Section 3 Comfort Controls and Audio Systems
In this section, you'll find out how to operate the comfort control and audio systems offered with your vehicle.
Be sure to read about the particular systems supplied with your vehicle.
3
-2 Comfort Controls
3
-2 Climate Control Panel
3
-6 Electronic Solar Sensor
3
-7 Air Conditioning
3
-7 Heating
3
-7 Defogging and Defrosting
3
-8 Rear Window Defogger
3
-8 Ventilation System
3
-10 HVAC Steering Wheel Controls
3
-10 Climate Control Personalization (If Equipped)
3
-10 Audio Systems
3
-10 Setting the Clock
3
-11 AM-FM Stereo with Cassette Tape Player
3
-15 CD Adapter Kits
3
-16 AM-FM Stereo with Cassette Tape and
Compact Disc Player with Radio Data
Systems (RDS) and Digital Signal
Processing (DPS) (If Equipped)3
-26 Radio Data Systems (RDS) Program
Type (PTY) Selections
3
-27 Trunk Mounted CD Changer (Option)
3
-31 Radio Personalization with Home and
Away Feature (If Equipped)
3
-31 Theft-Deterrent Feature
3
-32 Audio Steering Wheel Controls
3
-32 Understanding Radio Reception
3
-33 Tips About Your Audio System
3
-34 Care of Your Cassette Tape Player
3
-35 Care of Your Compact Discs
3
-35 Care of Your Compact Disc Player
3
-36 Power Antenna Mast Care

3-10 HVAC Steering Wheel Controls
Some heating and cooling
controls can be adjusted at
the steering wheel. Other
touch controls operate some
audio controls. See ªAudio
Steering Wheel Controlsº
in the Index.
(Fan): Press the up arrow lever to increase the fan
speed and the down arrow lever to decrease fan speed.
TEMP: Press the up arrow lever to increase
the temperature and the down arrow lever to
decrease temperature.
Climate Control Personalization (If Equipped)
This feature allows both drivers (driver 1 or 2 depending
on the number on the back of your remote keyless entry
transmitter) to personalize their own climate control
settings. For more information, see ªMemory and
Personalization Featuresº in the Index.
Audio Systems
Your audio system has been designed to operate easily
and give years of listening pleasure. You will get the
most enjoyment out of it if you acquaint yourself with it
first. Find out what your audio system can do and how
to operate all of its controls to be sure you're getting the
most out of the advanced engineering that went into it.
Your vehicle has a feature called Retained Accessory
Power (RAP). With RAP, you can play your audio
system even after the ignition is turned off.
See ªRetained Accessory Powerº in the Index.
Setting the Clock
Press and hold HR or MN until the time display begins
to change. Release the button as you get close to the
correct time. The time may be set anytime the clock is
displayed. There is a two
-second delay before the clock
goes into time
-set mode.

3-16 AM-FM Stereo with Cassette Tape and
Compact Disc Player with Radio Data
Systems (RDS) and Digital Signal
Processing (DSP) (If Equipped)
Playing the Radio
PWR (Power): Press this knob to turn the system on
and off.
VOL (Volume): Turn this knob clockwise to increase
volume. Turn it counterclockwise to decrease volume.
HR (Hour) or MN (Minute): Display the time with
the ignition off by pressing this button.
SOURCE: Press this button to select a source,
either cassette or compact disc. The audio source
must be loaded to play. Available loaded sources are
shown on the display. If a source is being used, it will be
underlined on the display. If none of the audio sources
are loaded, NO SOURCE LOADED will appear on the
display. Press this button again or press BAND to switch
back to the radio.

3-18
Setting the Tone (Bass/Treble)
TONE: Press and release this button until BASS or
TREBLE appears on the display. The radio keeps
separate tone settings for each band, preset
(except weather band presets) and source.
- LEVEL +: After selecting the desired tone control,
press the plus or minus symbol on this button to select
the desired level.
To save the tone settings for your presets, press and hold
the numbered button for the desired preset for more than
two seconds until you hear a beep.
Adjusting the Speakers (Balance/Fade)
TONE: Press and release this button until the desired
control BALANCE or FADE.
- LEVEL +: After selecting the BALANCE or FADE,
press the plus or minus symbol on this button to select
the desired level.
To save the tone settings for your presets, press and hold
the numbered pushbutton for the desired preset for more
than two seconds until you hear a beep.Using DSP
DSP (Digital Signal Processing): DSP is used to
provide a choice of four different listening experiences:
TALK, DRIVER SEAT, LIVE and AUDITORIUM.
DSP can be used while listening to the radio, the cassette
tape player or the CD player. Press this button to turn
DSP on. Press and release this button until the desired
selection appears on the display. To turn DSP off,
press and hold this button until DSP OFF appears on
the display. When DSP OFF is displayed, the system
will provide the best overall Bose

performance.
The radio keeps separate DSP settings for each band
(except weather band, which is always set to TALK),
preset and source.
TALK: This setting is used when listening to
non
-musical material such as news, talk shows,
sports broadcasts and books on tape. TALK makes
spoken words sound very clear.
DRIVER SEAT: This setting adjusts the audio to give
the driver the best possible sound qualities. DRIVER
SEAT can be used at any time for any material. Rear seat
passengers in the vehicle may not get the same effect.
LIVE: This setting is used to enhance the stereo effect.
AUDITORIUM: This setting is used to make the
listening space seem larger.

3-19
Using RDS
Your audio system is equipped with Radio Data Systems
(RDS). RDS mode gives you many useful new features.
With RDS the radio can do the following:

Seek only to stations with the types of programs
you want to listen to,

seek to stations with traffic announcements,

receive announcements concerning local and
national emergencies,

receive and display messages from radio stations and

search for a stronger station when a station is too
weak for listening.
RDS features are only available for use on FM stations
which broadcast RDS information.
(RDS Select): Press this button to use the
alternate RDS functions (RDS, TA, MSG, PTY and
the PTY arrows).HR (Hour) or MN (Minute): Press the RDS select
button, followed by one of these buttons to display the
time of the current station. STATION TIME IS will be
displayed. If a time has not been sent to the radio,
NO STATION TIME will be displayed. If you have
recently tuned to the station, you may need to wait a
minute before the time is available to the radio. To set
the clock to the current displayed station time, press and
hold HR or MN until TIME UPDATED is displayed.
There is a two second delay before the time is updated.
RDS does not have to be on to use this function,
but you must be tuned to an FM RDS station.
REGION: Press the RDS select button, then press
and hold the RDS pushbutton for two seconds.
REGION: ON will appear on the display. When an
RDS station becomes weak, this function searches for
a stronger station within the same network. A network
can span a great distance. One network can have stations
spread across a country or continent. Each network
breaks down into regions. With regions, local news
items like weather and traffic are available to you.
When the region function is on, the radio only searches
for stations in the same network and region. You can
only use the region function when RDS is on. Press the
RDS pushbutton again to turn the region function off.
REGION: OFF will appear on the display.

3-30
SIDE: Press this button to select the next disc in the
changer. If your vehicle is equipped with the AM
-FM
Stereo with Cassette Tape Player, CD and the disc
number will appear on the display each time you press
this button. If your vehicle is equipped with any other
audio system, DISC LOADING will appear on the
display and the disc number on the radio display will
go to that of the next available CD each time you press
this button.
SOURCE: Press this button to select a source.
The audio source must be loaded to play. If none of
the audio sources are loaded, NO SOURCE LOADED
will appear on the display. (CD will be displayed for
a few seconds instead on the AM
-FM Stereo with
Cassette Tape Player, then the radio will play.) Press this
button again or press BAND to switch back to the radio.
Slide the CD changer door all the way open and the disc
holder will automatically eject.Compact Disc Changer Errors
CD CHANGER ERROR could be displayed for one of
the following reasons:

The road is too rough. The disc should play when
the road is smoother.

The disc is dirty, scratched, wet or loaded label
side up.

The air is very humid. If so, wait about an hour
and try again.
CD CHANGER DOOR OPEN is displayed when
the CD changer door is left open. (CHEK DOOR will be
displayed instead on the AM-FM Stereo with Cassette
Tape Player.) Completely close the changer door to
restore normal operation.
If any error occurs repeatedly or if an error cannot be
corrected, contact your dealer.