garage door opener CADILLAC ELDORADO 2002 10.G Owners Manual
[x] Cancel search | Manufacturer: CADILLAC, Model Year: 2002, Model line: ELDORADO, Model: CADILLAC ELDORADO 2002 10.GPages: 365, PDF Size: 2.5 MB
Page 74 of 365
2-17 Testing the Alarm
1. From inside the vehicle, roll down the window,
then get out of the vehicle, keeping the door open.
2. From outside of the vehicle, with the door open,
lock the vehicle using the power door lock or the
remote keyless entry transmitter and close the door.
Wait 30 seconds until the SECURITY light goes off.
3. Reach in and unlock the door using the manual lock
and open the door. The horn will sound and the
headlamps will flash.
If the alarm does not sound when it should, check to
see if the horn works. The horn fuse may be blown.
To replace the fuse, see ªFuses and Circuit Breakersº
in the Index. If the fuse does not need to be replaced,
you may need to have your vehicle serviced.
To reduce the possibility of theft, always activate the
theft
-deterrent system when leaving your vehicle.
Valet Lockout Button
The VALET lockout
button is located inside
the glove box.
Press the button to disable the use of the power trunk,
fuel door and garage door openers.
Press the button again to restore normal function to
these features. Locking the glove box with the door key
will also help to secure your vehicle.
The remote keyless entry transmitter can't be used to
open the trunk or fuel door if the VALET lockout button
is pressed in.
Page 104 of 365
2-47 Parade Dimming
This feature prohibits the dimming of the instrument
panel lights during daylight while the headlamps
are on. This feature operates with the light sensor for
the Twilight Sentinel and is fully automatic. When the
light sensor reads darkness outside, the instrument
panel lights can be adjusted by turning the exterior
lamp knob counterclockwise to dim and clockwise to
brighten lighting. Backlighting to the instrument panel
will turn on, regardless of light conditions.
Reading Lights
The front reading lights are located either in the
headliner or above the windows if you have a sunroof.
The two rear lights above the rear side windows.
To turn them on, turn the exterior lamp knob all the way
clockwise. These lights and the interior courtesy lights
automatically come on when either door is opened and
it is dark outside.
Press the lens to turn on the lights manually. Press it
again to turn them off.
If the reading lights are left on, they automatically shut
off 10 minutes after the ignition has been turned off.
Inadvertent Power Battery Saver
This feature is designed to protect your vehicle's battery
against drainage from the interior lamps, trunk lamp,
glove box lamp, cigarette lighters or the garage door
opener. When the ignition is turned off, the power to
these features will automatically turn off after 10 minutes
(three minutes if a new car has 15 miles (24 km) or less).
Power will be restored for an additional 10 minutes
if either door is opened, the trunk is opened or the
courtesy lamps are turned on.
Storage Mode Personalization
This feature is for long-term use and must be
programmed through the Driver Information
Center (DIC). This feature protects the battery by
placing your vehicle in a storage mode so that the radio,
amplifiers, instrument panel cluster and remote keyless
entry will not drain the battery over a long period of
time. For programming information, see ªMemory
and Personalization Featuresº in the Index.
Page 115 of 365
2-58
HomeLink Transmitter (Option)
The HomeLink Transmitter buttons are located on the
overhead console.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference,
and (2) this device must accept any interference
received, including interference that may cause
undesired operation.This device complies with RSS
-210 of Industry
Canada. Operation is subject to the following two
conditions: (1) this device may not cause interference,
and (2) this device must accept any interference,
including interference that may cause undesired
operation of the device.
Changes and modifications to this system by other than
an authorized service facility could void authorization to
use this equipment.
Programming the HomeLink Transmitter
Do not use the HomeLink Transmitter with any garage
door opener that does not have the ªstop and reverseº
feature. This includes any garage door opener model
manufactured before April 1, 1982.
Be sure that people and objects are clear of the garage
door you are programming.
It is recommended that a new battery be installed in
your hand
-held transmitter for quicker and more
accurate transmission of the radio frequency.
Page 116 of 365
2-59
Your vehicle's engine should be turned off while
programming the transmitter. Follow these steps to
program up to three channels:
1. Decide which one of the three channels (one of the
HomeLink buttons) you want to program.
2. Press and hold the desired button on HomeLink
through Step 3.
3. When the HomeLink indicator light begins to blink
slowly (this may take up to 30 seconds), hold the
hand
-held transmitter about 1 to 3 inches (3 to 8 cm)
away from HomeLink and then press and hold the
transmit button on the hand
-held transmitter.
Continue to hold both buttons until the indicator
light on HomeLink begins to flash rapidly
(this may take up to 90 seconds).If you have trouble programming HomeLink,
make sure that you have followed the directions
exactly as described and that the battery in the
hand
-held transmitter is not weak. If you still
cannot program it, move the hand
-held transmitter
to the left or right or forward or backward or flip it
upside down. HomeLink may not work with older
garage door openers that do not meet current
Federal Consumer Safety Standards. If you cannot
program the transmitter after repeated attempts,
refer to ªTraining a Garage Door Opener with Rolling
Codesº later in this section or contact the manufacturer
of HomeLink at 1
-800-355-3515, or on the internet
at www.homelink.com.
Be sure to keep the original hand
-held transmitter in
case you need to erase and reprogram HomeLink.
Page 117 of 365
2-60 Training a Garage Door Opener with a
ªRolling Codeº Feature (If Equipped)
If you have not previously programmed the hand-held
transmitter to HomeLink, see ªProgramming the
HomeLink Transmitterº listed previously. If you have
completed this programming already, you now need
to train the garage door opener motor head unit to
recognize HomeLink.
1. Find the ªLearnº or ªSmartº button on the
garage door opener motor head unit. The exact
location and color will vary by garage door opener
brand. If you have difficulty finding the ªLearnº or
ªSmartº button, refer to your garage door opener
owner's manual or contact the manufacturer of
HomeLink at 1
-800-355-3515, or on the internet
at www.homelink.com.
Because of the steps involved, it may be helpful to
have another person assist in programming the
transmitter.2. Press the ªLearnº or ªSmartº button on the garage
door opener motor head unit. An indicator light will
begin to flash when the motor head unit enters the
training mode.
Following this step, you have 30 seconds to
start Step 3.
3. Return to HomeLink in your vehicle and firmly
press and release the programmed HomeLink button
three times.
The rolling
-code garage door opener should now
recognize HomeLink. You may either use HomeLink
or the hand
-held transmitter to open the garage door.
If after following these instructions, you still have
problems training the garage door opener, contact the
manufacturer of HomeLink at 1
-800-355-3515, or on
the internet at www.homelink.com.
Page 323 of 365
6-63
Underhood Fuse Block
The underhood fuse block is located next to the engine
air cleaner/filter in the engine compartment on the
driver's side of the vehicle. Lift the cover to gain access.Fuse Usage
SPARE Spare Fuse
CNR LPS Cornering Lamp Switch,
Right and Left Cornering Lamps
INT LPS Trunk Lamp, Courtesy Lamps,
Front Vanity Lamps, Glove Box
Lamp, Garage Door Opener,
Courtesy Lamp Relay