lights CADILLAC ELDORADO 2002 10.G Owners Manual

iv
Vehicle Damage Warnings
Also, in this book you will find these notices:
NOTICE:
These mean there is something that could damage
your vehicle.
In the notice area, we tell you about something that can
damage your vehicle. Many times, this damage would
not be covered by your warranty, and it could be costly.
But the notice will tell you what to do to help avoid
the damage.
When you read other manuals, you might see
CAUTION and NOTICE warnings in different
colors or in different words.
You'll also see warning labels on your vehicle.
They use the same words, CAUTION or NOTICE.
Vehicle Symbols
Your vehicle may be equipped with components and
labels that use symbols instead of text. Symbols,
used on your vehicle, are shown along with the text
describing the operation or information relating to a
specific component, control, message, gage or indicator.
If you need help figuring out a specific name of a
component, gage or indicator reference the following
topics in the Index:

ªEngine Compartment Overviewº

ªInstrument Panelº

ªComfort Controlsº

ªAudio Systemsº
Also see ªWarning Lights and Gagesº in the Index.

2-
2-1
Section 2 Features and Controls
Here you can learn about the many standard and optional features on your vehicle, and information on starting,
shifting and braking. Also explained are the instrument panel and the warning systems that tell you if everything is
working properly
-- and what to do if you have a problem.
2
-2 Windows
2
-4 Keys
2
-6 Door Locks
2
-8 Remote Keyless Entry System
2
-12 Trunk
2
-15 Theft
2
-16 Theft-Deterrent System
2
-18 PASS-Key
II
2
-19 New Vehicle ªBreak-Inº
2
-19 Ignition Positions
2
-21 Starting Your Engine
2
-22 Engine Coolant Heater (If Equipped)
2
-24 Automatic Transaxle Operation
2
-27 Parking Brake
2
-29 Shifting Into PARK (P)
2
-31 Shifting Out of PARK (P)
2
-31 Parking Over Things That Burn2
-32 Engine Exhaust
2
-32 Running Your Engine While You're Parked
2
-33 Tilt Wheel
2
-34 Turn Signal/Multifunction Lever
2
-42 Exterior Lamps
2
-46 Interior Lamps
2
-48 Mirrors
2
-51 Storage Compartments
2
-53 Sun Visors
2
-54 OnStar
System (If Equipped)
2
-57 Sunroof (Option)
2
-58 HomeLink
Transmitter (Option)
2
-62 The Instrument Panel -- Your
Information System
2
-66 Warning Lights, Gages and Indicators
2
-78 Driver Information Center (DIC)

2-42
Using Cruise Control on Hills
How well your cruise control will work on hills depends
upon your speed, load and the steepness of the hills.
When going up steep hills, you may have to step on the
accelerator pedal to maintain your speed. When going
downhill, you may have to brake or shift to a lower gear
to keep your speed down. Of course, applying the brakes
or downshifting into FIRST (1) takes you out of cruise
control. Many drivers find this to be too much trouble
and don't use cruise control on steep hills.
Ending Cruise Control
There are two ways to end cruise control:

Step lightly on the brake pedal.

Move the CRUISE switch to OFF.
Erasing Speed Memory
The cruise control set speed memory is erased when you
turn off the cruise control or the ignition.Exterior Lamps
The exterior lamp knob is
located to the left of the
steering wheel on the
instrument panel.
Pull the knob toward you to operate the lamps.
The exterior lamp knob has three positions:
Off: Pushing the knob all the way in turns off all lamps
except the Daytime Running Lamps (DRL).
Parking Lamps: Pulling the knob to the first position
turns on the parking lamps together with the following:

Sidemarker Lamps

Taillamps

License Plate Lamps

Instrument Panel Lights

2-43
Headlamps: Pulling the knob to the second position
turns on the headlamps, together with the previously
listed lamps and lights.
Wiper
-Activated Headlamps
This feature activates the headlamps and parking lamps
after the windshield wipers have been in use for
approximately 20 seconds.
In order to operate the wiper
-activated headlamps, the
Twilight Sentinel
must be turned on. This feature lights
the way in poor weather and it also makes your vehicle
more visible to other drivers. If the wiper
-activated
headlamps are on, and the ignition switch is turned off,
the wiper
-activated headlamps will immediately turn off.
The wiper
-activated headlamps will deactivate if you
turn off the Twilight Sentinel or if the windshield wipers
have been turned off for a period of one or two seconds.
Lamps On Reminder
If the exterior lamp knob is activated, you will hear a
warning chime if you open either door while leaving the
lamps on. An exception to this is when you're using
Twilight Sentinel.
Daytime Running Lamps
Daytime Running Lamps (DRL) can make it easier
for others to see the front of your vehicle during
the day. DRL can be helpful in many different
driving conditions, but they can be especially helpful
in the short periods after dawn and before sunset.
Fully functional daytime running lamps are required
on all vehicles first sold in Canada.
The DRL system will make the high
-beam headlamps
come on at reduced brightness when:

The ignition is on,

the exterior lamp knob is not in the
headlamp position

the transaxle is not in PARK (P).
When DRL are on, only your high
-beam headlamps
(at reduced brightness) will be on. No other exterior
lamps such as the parking lamps, taillamps, etc., will be
on when the DRL are being used. Your instrument panel
won't be lit up either.

2-46
Light Sensor
The light sensor for the Daytime Running Lamps (DRL)
and the Twilight Sentinel is located in the center of the
front defogger grille. If you cover the sensor, it will read
ªdarkº and the lamps will come on.
Exterior Lighting Battery Saver
If the parking lamps have been left on, the exterior lamps
will turn off approximately 10 minutes after the ignition
is turned to LOCK or ACCESSORY. This protects
against draining the battery in case you have accidentally
left the headlamps or parking lamps on. If you need to
purposely leave the lamps on for more than 10 minutes
with the ignition in LOCK or ACCESSORY, turn the
exterior lamps off and then back on. To delay the lamps
from turning off, see ªTwilight Sentinelº in the Index.
Interior Lamps
Instrument Panel Brightness Control
This feature controls the brightness of the instrument
panel lights.
The knob for this feature is located to the left of the
steering wheel on the instrument panel. This knob is also
used to control the exterior lamps. See ªExterior Lampsº
listed previously in this section for more information.
Turn the knob clockwise to brighten the lights or
counterclockwise to dim them.
Illuminated Entry
The illuminated entry system turns on the courtesy
lamps and the backlighting to the door controls and
to the exterior lamp knob when a door is opened or if
you press a remote keyless entry transmitter button.
Since the illuminated entry system has a photocell,
this means that it must be dark outside in order for the
courtesy lamps or backlighting to turn on. The courtesy
lamps turn off approximately 20 seconds after the last
door is closed or after the ignition is turned to RUN.

2-47 Parade Dimming
This feature prohibits the dimming of the instrument
panel lights during daylight while the headlamps
are on. This feature operates with the light sensor for
the Twilight Sentinel and is fully automatic. When the
light sensor reads darkness outside, the instrument
panel lights can be adjusted by turning the exterior
lamp knob counterclockwise to dim and clockwise to
brighten lighting. Backlighting to the instrument panel
will turn on, regardless of light conditions.
Reading Lights
The front reading lights are located either in the
headliner or above the windows if you have a sunroof.
The two rear lights above the rear side windows.
To turn them on, turn the exterior lamp knob all the way
clockwise. These lights and the interior courtesy lights
automatically come on when either door is opened and
it is dark outside.
Press the lens to turn on the lights manually. Press it
again to turn them off.
If the reading lights are left on, they automatically shut
off 10 minutes after the ignition has been turned off.
Inadvertent Power Battery Saver
This feature is designed to protect your vehicle's battery
against drainage from the interior lamps, trunk lamp,
glove box lamp, cigarette lighters or the garage door
opener. When the ignition is turned off, the power to
these features will automatically turn off after 10 minutes
(three minutes if a new car has 15 miles (24 km) or less).
Power will be restored for an additional 10 minutes
if either door is opened, the trunk is opened or the
courtesy lamps are turned on.
Storage Mode Personalization
This feature is for long-term use and must be
programmed through the Driver Information
Center (DIC). This feature protects the battery by
placing your vehicle in a storage mode so that the radio,
amplifiers, instrument panel cluster and remote keyless
entry will not drain the battery over a long period of
time. For programming information, see ªMemory
and Personalization Featuresº in the Index.

2-66 Tachometer
The tachometer is located in
the instrument panel cluster,
to the left of the speedometer.
NOTICE:
Do not operate the engine with the tachometer in
the shaded area or engine damage may occur.
This gage indicates the engine speed in revolutions
per minute (rpm).Engine Speed Limiter
This feature prevents the engine from operating at too
many revolutions per minute (rpm). When the engine's
rpm is critically high, the fuel supply to the engine
is shut off. When the engine speed slows, the fuel
supply will come on again. This helps prevent damage
to the engine.
Warning Lights, Gages and Indicators
This part describes the warning lights and gages that may
be on your vehicle. The pictures will help you locate them.
Warning lights and gages can signal that something is
wrong before it becomes serious enough to cause an
expensive repair or replacement. Paying attention to
your warning lights and gages could also save you or
others from injury.
Warning lights come on when there may be or is a
problem with one of your vehicle's functions. As you
will see in the details on the next few pages, some
warning lights come on briefly when you start the
engine just to let you know they're working. If you are
familiar with this section, you should not be alarmed
when this happens.

2-67
Gages can indicate when there may be or is a problem
with one of your vehicle's functions. Often gages and
warning lights work together to let you know when
there's a problem with your vehicle.
When one of the warning lights comes on and stays on
when you are driving, or when one of the gages shows
there may be a problem, check the section that tells you
what to do about it. Please follow this manual's advice.
Waiting to do repairs can be costly
-- and even
dangerous. So please get to know your warning lights
and gages. They're a big help.
Your vehicle also has a Driver Information Center (DIC)
that works along with the warning lights and gages.
See ªDriver Information Center (DIC)º in the Index
for more information.
Safety Belt Reminder Light
When the key is turned to RUN or START, a chime will
come on for about eight seconds to remind people to
fasten their safety belts, unless the driver's safety belt is
already buckled.
The safety belt light will
also come on and stay on
for about 20 seconds,
then it will flash for
about 70 seconds.
If the driver's belt is already buckled, neither the chime
nor the light will come on.

2-90
Lock/Unlock Confirmation
This personalization feature allows the driver to program
the parking lamps to flash when the buttons on the
remote keyless entry transmitter are pressed, to program
the horn to sound when the button with the lock symbol
is pressed and/or to program the exterior lamps to turn on
when the button with the unlock symbol is pressed on the
remote keyless entry transmitter.
Programmable Modes
Mode 1 (LGHTS FLSH AT UNLOCK): Parking
lamps flash twice when the button with the unlock
symbol on the remote keyless entry transmitter is pressed.
Mode 2 (LIGHTS FLASH AT LOCK): Parking lamps
flash once when the button with the lock symbol on the
remote keyless entry transmitter is pressed.
Mode 3 (HORN SOUNDS AT LOCK): Horn sounds
when the button with the lock symbol on the remote
keyless entry transmitter is pressed.Mode 4 (EXT LIGHTS AT UNLOCK): Exterior
lamps turn on when the button with the unlock symbol
on the remote keyless entry transmitter is pressed
and it is dark outside. These lamps stay on for about
20 seconds or until the key is turned to OFF.
Before your vehicle was shipped from the factory, it was
programmed to enable Mode 1 and Mode 2. The modes
to which the vehicle was programmed may have been
changed since it left the factory. To determine the modes
to which the vehicle is programmed or to program the
vehicle to different modes, do the following:
1. Enter feature programming following the
instructions listed previously.
2. Press the SKIP INFO button until LOCK/UNLOCK
appears on the display.
3. Press YES TRIP RESET to select this feature for
programming. Mode 1 described previously will
appear on the display once a yes response is made.

4-17
Here are some tips on night driving.

Drive defensively.

Don't drink and drive.

Since you can't see as well, you may need to
slow down and keep more space between you
and other vehicles.

Slow down, especially on higher speed roads.
Your headlamps can light up only so much
road ahead.

In remote areas, watch for animals.

If you're tired, pull off the road in a safe place
and rest.
No one can see as well at night as in the daytime. But as
we get older these differences increase. A 50
-year-old
driver may require at least twice as much light to see the
same thing at night as a 20
-year-old.
What you do in the daytime can also affect your night
vision. For example, if you spend the day in bright
sunshine you are wise to wear sunglasses. Your eyes
will have less trouble adjusting to night. But if you're
driving, don't wear sunglasses at night. They may cut
down on glare from headlamps, but they also make a lot
of things invisible.You can be temporarily blinded by approaching
headlamps. It can take a second or two, or even
several seconds, for your eyes to readjust to the dark.
When you are faced with severe glare (as from a driver
who doesn't lower the high beams, or a vehicle with
misaimed headlamps), slow down a little. Avoid staring
directly into the approaching headlamps.
Keep your windshield and all the glass on your vehicle
clean
-- inside and out. Glare at night is made much
worse by dirt on the glass. Even the inside of the glass
can build up a film caused by dust. Dirty glass makes
lights dazzle and flash more than clean glass would,
making the pupils of your eyes contract repeatedly.
Remember that your headlamps light up far less of a
roadway when you are in a turn or curve. Keep your
eyes moving; that way, it's easier to pick out dimly
lighted objects. Just as your headlamps should be
checked regularly for proper aim, so should your eyes
be examined regularly. Some drivers suffer from night
blindness
-- the inability to see in dim light -- and aren't
even aware of it.