spare tire CADILLAC ESCALADE ESV 2010 Owners Manual

Black plate (14,1)Cadillac Escalade/Escalade ESV Owner Manual - 2010
Before You Go Off-Roading .
Have all necessary maintenance and service
work done. .
Make sure there is enough fuel, that fluid levels are
where they should be, and that the spare tire, if the
vehicle has one, is fully inflated. .
Be sure to read all the information about
all-wheel-drive vehicles in this manual. .
Make sure all underbody shields, if the vehicle has
them, are properly attached. .
Know the local laws that apply to off-roading where
you will be driving or check with law enforcement
people in the area. .
Be sure to get the necessary permission if you will
be on private land. If you think you will need some more ground clearance
at the front of your vehicle, you can remove the front
fascia lower air dam. The air dam is held in place by
two bolts and 10 snaps accessible from underneath the
front fascia.
To remove the air dam:
1. Remove the two outboard air dam bolts.
2. With a flat ‐ blade tool, disengage the snaps.
3. After the bolts are removed and the snaps are
disengaged, push forward on the air dam until it
is free.
Notice: Operating your vehicle for extended periods
without the front fascia lower air dam installed can
cause improper air flow to the engine. Always be
sure to replace the front fascia air dam when you
are finished off-road driving.
After off-roading, be sure to reinstall the air dam:
1. Line up the snaps and push the air dam rearward
to engage the snaps.
2. Install the two outboard bolts.
6-14

Black plate (2,1)Cadillac Escalade/Escalade ESV Owner Manual - 2010
Section 7 Service and Appearance CareWindshield Wiper Blade Replacement . . . . . . . . . . . 7-57
Tires . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-58
Tire Sidewall Labeling . . . . . . . . . . . . . . . . . . . . . . . . . 7-60
Tire Terminology and Definitions . . . . . . . . . . . . . . . 7-62
Inflation - Tire Pressure . . . . . . . . . . . . . . . . . . . . . . . . 7-65
High-Speed Operation . . . . . . . . . . . . . . . . . . . . . . . . . 7-66
Tire Pressure Monitor System . . . . . . . . . . . . . . . . . 7-67
Tire Pressure Monitor Operation . . . . . . . . . . . . . . . 7-68
Tire Inspection and Rotation . . . . . . . . . . . . . . . . . . . 7-71
When It Is Time for New Tires . . . . . . . . . . . . . . . . . 7-73
Buying New Tires . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-73
Different Size Tires and Wheels . . . . . . . . . . . . . . . 7-75
Uniform Tire Quality Grading . . . . . . . . . . . . . . . . . . . 7-76
Wheel Alignment and Tire Balance . . . . . . . . . . . . 7-77
Wheel Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-77
Tire Chains . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-78
If a Tire Goes Flat . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-79
Changing a Flat Tire . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-80
Removing the Spare Tire and Tools . . . . . . . . . . . . 7-81
Removing the Flat Tire and Installing the
Spare Tire . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-86
Secondary Latch System . . . . . . . . . . . . . . . . . . . . . . 7-91
Storing a Flat or Spare Tire and Tools . . . . . . . . . 7-94
Spare Tire . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-98 Appearance Care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-99
Interior Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-99
Fabric/Carpet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-100
Leather . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-101
Instrument Panel, Vinyl, and Other Plastic
Surfaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-102
Wood Panels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-102
Speaker Covers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-102
Care of Safety Belts . . . . . . . . . . . . . . . . . . . . . . . . . . 7-103
Weatherstrips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-103
Washing Your Vehicle . . . . . . . . . . . . . . . . . . . . . . . . 7-103
Cleaning Exterior Lamps/Lenses . . . . . . . . . . . . . 7-104
Finish Care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-104
Windshield, Backglass, and Wiper Blades . . . . 7-105
Aluminum or Chrome-Plated Wheels
and Trim . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-106
Tires . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-107
Sheet Metal Damage . . . . . . . . . . . . . . . . . . . . . . . . . 7-107
Finish Damage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-107
Underbody Maintenance . . . . . . . . . . . . . . . . . . . . . 7-107
Chemical Paint Spotting . . . . . . . . . . . . . . . . . . . . . . 7-108
Vehicle Identification . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-108
Vehicle Identification Number (VIN) . . . . . . . . . . . 7-108
Service Parts Identification Label . . . . . . . . . . . . . 7-109
7-2

Black plate (52,1)Cadillac Escalade/Escalade ESV Owner Manual - 2010
Headlamp Aiming The vehicle has a visual optical headlamp aiming
system. The aim of the headlamps have been preset at
the factory and should need no further adjustment.
However, if the vehicle is damaged in a crash, the aim
of the headlamps may be affected and adjustment may
be necessary.
If oncoming vehicles flash their high beams at you, this
may mean the vertical aim of your headlamps needs to
be adjusted.
It is recommended that the vehicle is taken to your
dealer for service if the headlamps need to be adjusted.
It is possible however, to re-aim the headlamps as
described.
The vehicle should: .
Be placed so the headlamps are 25 ft. (7.6 m) from
a light colored wall or other flat surface. .
Have all four tires on a level surface which is level
all the way to the wall or other flat surface. .
Be placed so it is perpendicular to the wall or other
flat surface. .
Not have any snow, ice, or mud on it. .
Be fully assembled and all other work stopped
while headlamp aiming is being performed. .
Be normally loaded with a full tank of fuel and one
person or 160 lbs (75 kg) sitting on the driver seat. .
Have the tires properly inflated. .
Have the spare tire is in its proper location in the
vehicle.
Headlamp aiming is done with the vehicle's low-beam
headlamps. The high-beam headlamps will be correctly
aimed if the low-beam headlamps are aimed properly.
To adjust the vertical aim:
1. Open the hood. See Hood Release
on page 7 ‑ 15
for more information.
2. Locate the center of
the projector lens of
the low ‐ beam
headlamp.
3. Record the distance from the ground to the center
of the projector lens of the low ‐ beam headlamp.
7-52

Black plate (65,1)Cadillac Escalade/Escalade ESV Owner Manual - 2010
Inflation - Tire Pressure If your vehicle is a Two-mode Hybrid, see the
Two-mode Hybrid manual for more information.
Tires need the correct amount of air pressure to
operate effectively. Notice:
Do not let anyone tell you that
under ‐ inflation or over ‐ inflation is all right.
It is not. If your tires do not have enough air
(under ‐ inflation), you can get the following: .
Too much flexing .
Too much heat .
Tire overloading .
Premature or irregular wear .
Poor handling .
Reduced fuel economy
If your tires have too much air (over ‐ inflation),
you can get the following: .
Unusual wear .
Poor handling .
Rough ride .
Needless damage from road hazards A vehicle specific Tire and Loading Information
label is attached to your vehicle. This label shows
your vehicle's original equipment tires and the
correct inflation pressures for your tires when they
are cold. The recommended cold tire inflation
pressure, shown on the label, is the minimum
amount of air pressure needed to support your
vehicle's maximum load carrying capacity.
For additional information regarding how much
weight your vehicle can carry, and an example of
the Tire and Loading Information label, see
Loading the Vehicle
on page 6 ‑ 32 . How you load
your vehicle affects vehicle handling and ride
comfort. Never load your vehicle with more weight
than it was designed to carry.
When to Check Check your tires once a month or more.
Do not forget to check the pressure of the spare
tire. See Spare Tire on page 7 ‑ 98 for additional
information.
7-65

Black plate (67,1)Cadillac Escalade/Escalade ESV Owner Manual - 2010
Tire Pressure Monitor System The Tire Pressure Monitor System (TPMS) uses radio
and sensor technology to check tire pressure levels.
The TPMS sensors monitor the air pressure in your
vehicle's tires and transmit tire pressure readings to a
receiver located in the vehicle.
Each tire, including the spare (if provided), should be
checked monthly when cold and inflated to the inflation
pressure recommended by the vehicle manufacturer
on the vehicle placard or tire inflation pressure label.
(If your vehicle has tires of a different size than the size
indicated on the vehicle placard or tire inflation pressure
label, you should determine the proper tire inflation
pressure for those tires.)
As an added safety feature, your vehicle has been
equipped with a tire pressure monitoring system
(TPMS) that illuminates a low tire pressure telltale when
one or more of your tires is significantly under ‐ inflated.
Accordingly, when the low tire pressure telltale
illuminates, you should stop and check your tires as
soon as possible, and inflate them to the proper
pressure. Driving on a significantly under ‐ inflated tire
causes the tire to overheat and can lead to tire failure.
Under ‐ inflation also reduces fuel efficiency and tire
tread life, and may affect the vehicle's handling and
stopping ability. Please note that the TPMS is not a substitute for proper
tire maintenance, and it is the driver's responsibility to
maintain correct tire pressure, even if under ‐ inflation
has not reached the level to trigger illumination of the
TPMS low tire pressure telltale.
Your vehicle has also been equipped with a TPMS
malfunction indicator to indicate when the system is not
operating properly. The TPMS malfunction indicator is
combined with the low tire pressure telltale. When the
system detects a malfunction, the telltale will flash for
approximately one minute and then remain continuously
illuminated. This sequence will continue upon
subsequent vehicle start ‐ ups as long as the malfunction
exists.
When the malfunction indicator is illuminated, the
system may not be able to detect or signal low tire
pressure as intended. TPMS malfunctions may occur
for a variety of reasons, including the installation of
replacement or alternate tires or wheels on the vehicle
that prevent the TPMS from functioning properly.
Always check the TPMS malfunction telltale after
replacing one or more tires or wheels on your vehicle to
ensure that the replacement or alternate tires and
wheels allow the TPMS to continue to function properly.
See Tire Pressure Monitor Operation on page 7 ‑ 68 for
additional information.
7-67

Black plate (68,1)Cadillac Escalade/Escalade ESV Owner Manual - 2010
Federal Communications Commission
(FCC) and Industry Canada See Radio Frequency Statement on page 9 ‑ 21 for
information regarding Part 15 of the Federal
Communications Commission (FCC) rules and Industry
Canada Standards RSS-210/220/310.
Tire Pressure Monitor Operation If your vehicle is a Two ‐ mode Hybrid, see the
Two ‐ mode Hybrid manual for more information.
This vehicle may have a Tire Pressure Monitor System
(TPMS). The TPMS is designed to warn the driver when
a low tire pressure condition exists. TPMS sensors are
mounted onto each tire and wheel assembly, excluding
the spare tire and wheel assembly. The TPMS sensors
monitor the air pressure in the vehicle's tires and
transmit the tire pressure readings to a receiver located
in the vehicle.
When a low tire pressure
condition is detected, the
TPMS illuminates the low
tire pressure warning light
located on the instrument
panel cluster. At the same time a message to check the pressure in a
specific tire appears on the Driver Information Center
(DIC) display. The low tire pressure warning light and
the DIC warning message come on at each ignition
cycle until the tires are inflated to the correct inflation
pressure. Using the DIC, tire pressure levels can be
viewed by the driver. For additional information and
details about the DIC operation and displays see DIC
Operation and Displays
on page 4 ‑ 42 and DIC
Warnings and Messages on page 4 ‑ 49 .
The low tire pressure warning light may come on in cool
weather when the vehicle is first started, and then turn
off as you start to drive. This could be an early indicator
that the air pressure in the tire(s) are getting low and
need to be inflated to the proper pressure.
A Tire and Loading Information label, attached to your
vehicle, shows the size of your vehicle's original
equipment tires and the correct inflation pressure for
your vehicle's tires when they are cold. See Loading the
Vehicle
on page 6 ‑ 32 , for an example of the Tire and
Loading Information label and its location on your
vehicle. Also see Inflation - Tire Pressure on page 7 ‑ 65 .
Your vehicle's TPMS can warn you about a low tire
pressure condition but it does not replace normal tire
maintenance. See Tire Inspection and Rotation
on
page 7 ‑ 71 and Tires on page 7 ‑ 58 .
7-68

Black plate (69,1)Cadillac Escalade/Escalade ESV Owner Manual - 2010
Notice: Liquid tire sealants could damage the Tire
Pressure Monitor System (TPMS) sensors. Sensor
damage caused by using a tire sealant is not
covered by your warranty. Do not use liquid tire
sealants.
TPMS Malfunction Light and Message The TPMS will not function properly if one or more of
the TPMS sensors are missing or inoperable. When the
system detects a malfunction, the low tire warning light
flashes for about one minute and then stays on for the
remainder of the ignition cycle. A DIC warning message
is also displayed. The low tire warning light and DIC
warning message come on at each ignition cycle until
the problem is corrected. Some of the conditions that
can cause the malfunction light and DIC message to
come on are: .
One of the road tires has been replaced with the
spare tire. The spare tire does not have a TPMS
sensor. The TPMS malfunction light and DIC
message should go off once you re ‐ install the road
tire containing the TPMS sensor. .
The TPMS sensor matching process was started
but not completed or not completed successfully
after rotating the vehicle's tires. The DIC message
and TPMS malfunction light should go off once the
TPMS sensor matching process is performed
successfully. See “ TPMS Sensor Matching
Process ” later in this section. .
One or more TPMS sensors are missing or
damaged. The DIC message and the TPMS
malfunction light should go off when the TPMS
sensors are installed and the sensor matching
process is performed successfully. See your dealer
for service. .
Replacement tires or wheels do not match your
vehicle's original equipment tires or wheels. Tires
and wheels other than those recommended for
your vehicle could prevent the TPMS from
functioning properly. See Buying New Tires
on
page 7 ‑ 73
. .
Operating electronic devices or being near facilities
using radio wave frequencies similar to the TPMS
could cause the TPMS sensors to malfunction.
If the TPMS is not functioning it cannot detect or signal
a low tire condition. See your dealer for service if the
TPMS malfunction light and DIC message comes on
and stays on.
7-69

Black plate (71,1)Cadillac Escalade/Escalade ESV Owner Manual - 2010
5. Remove the valve cap from the valve cap stem.
Activate the TPMS sensor by increasing or
decreasing the tire's air pressure for five seconds,
or until a horn chirp sounds. The horn chirp, which
may take up to 30 seconds to sound, confirms that
the sensor identification code has been matched to
this tire and wheel position.
6. Proceed to the passenger side front tire, and
repeat the procedure in Step 5.
7. Proceed to the passenger side rear tire, and repeat
the procedure in Step 5.
8. Proceed to the driver side rear tire, and repeat the
procedure in Step 5. The horn sounds two times to
indicate the sensor identification code has been
matched to the driver side rear tire, and the TPMS
sensor matching process is no longer active. The
TIRE LEARNING ACTIVE message on the DIC
display screen goes off. 9. Turn the ignition switch to LOCK/OFF.
10. Set all four tires to the recommended air pressure
level as indicated on the Tire and Loading
Information label.
11. Put the valve caps back on the valve stems.
Tire Inspection and Rotation We recommend that you regularly inspect your
vehicle's tires, including the spare tire, for signs of
wear or damage. See When It Is Time for New
Tires
on page 7 ‑ 73 for more information.
Tires should be rotated every 5,000 to 8,000 miles
(8 000 to 13 000 km). See Scheduled Maintenance
on page 8 ‑ 3 .
The purpose of a regular tire rotation is to achieve
a uniform wear for all tires on the vehicle. This will
ensure that your vehicle continues to perform
most like it did when the tires were new.
7-71

Black plate (72,1)Cadillac Escalade/Escalade ESV Owner Manual - 2010
Any time you notice unusual wear, rotate your
tires as soon as possible and check wheel
alignment. Also check for damaged tires or
wheels. See When It Is Time for New Tires
on
page 7 ‑ 73
and Wheel Replacement on page 7 ‑ 77 .
When rotating your vehicle's tires, always use the
correct rotation pattern shown here.
Do not include the spare tire in the tire rotation.
After the tires have been rotated, adjust the front
and rear inflation pressures as shown on the Tire
and Loading Information label. See Inflation - Tire
Pressure
on page 7 ‑ 65 and Loading the Vehicle on
page 6 ‑ 32
. Reset the Tire Pressure Monitor System. See Tire
Pressure Monitor Operation
on page 7 ‑ 68 .
Make certain that all wheel nuts are properly
tightened. See “ Wheel Nut Torque ” under
Capacities and Specifications
on page 7 ‑ 117 .
{ WARNING: Rust or dirt on a wheel, or on the parts to
which it is fastened, can make wheel nuts
become loose after time. The wheel could
come off and cause an accident. When you
change a wheel, remove any rust or dirt
from places where the wheel attaches to
the vehicle. In an emergency, you can use
a cloth or a paper towel to do this; but be
sure to use a scraper or wire brush later,
if needed, to get all the rust or dirt off. See
Changing a Flat Tire
on page 7 ‑ 80 .
Make sure the spare tire is stored securely. Push,
pull, and then try to rotate or turn the tire. If it
moves, tighten the cable. See Storing a Flat or
Spare Tire and Tools
on page 7 ‑ 94 .
7-72

Black plate (73,1)Cadillac Escalade/Escalade ESV Owner Manual - 2010
When It Is Time for New Tires Various factors, such as maintenance, temperatures,
driving speeds, vehicle loading, and road conditions,
influence when you need new tires.
One way to tell when it is
time for new tires is to
check the treadwear
indicators, which appear
when your tires have only
1/16 inch (1.6 mm) or less
of tread remaining. Some
commercial truck tires
may not have treadwear
indicators.
You need new tires if any of the following statements
are true: .
You can see the indicators at three or more places
around the tire. .
You can see cord or fabric showing through the
tire's rubber. .
The tread or sidewall is cracked, cut, or snagged
deep enough to show cord or fabric. .
The tire has a bump, bulge, or split. .
The tire has a puncture, cut, or other damage that
cannot be repaired well because of the size or
location of the damage.
The rubber in tires degrades over time, even if they are
not being used. This is also true for the spare tire,
if your vehicle has one. Multiple conditions affect how
fast this aging takes place, including temperatures,
loading conditions, and inflation pressure maintenance.
With proper care and maintenance tires will typically
wear out before they degrade due to age. If you are
unsure about the need to replace your tires as they get
older, consult the tire manufacturer for more information.
Buying New Tires GM has developed and matched specific tires for your
vehicle. The original equipment tires installed on your
vehicle, when it was new, were designed to meet
General Motors Tire Performance Criteria Specification
(TPC spec) system rating. If you need replacement
tires, GM strongly recommends that you get tires with
the same TPC Spec rating. This way, your vehicle will
continue to have tires that are designed to give the
same performance and vehicle safety, during normal
use, as the original tires.
7-73