seat memory CADILLAC ESCALADE EXT 2002 2.G Owners Manual
[x] Cancel search | Manufacturer: CADILLAC, Model Year: 2002, Model line: ESCALADE EXT, Model: CADILLAC ESCALADE EXT 2002 2.GPages: 427, PDF Size: 3.16 MB
Page 9 of 427
1-3 Memory Seat and Memory Mirrors
The memory function controls are located on the
driver's door trim panel.
For this function to work, it must be enabled/configured
in the Secondary Information Center (SIC).
See ªSecondary Information Centerº in the Index
for more information.These buttons are used to program and recall the
memory settings for the driver's seat and both
the driver's and the passenger's outside mirrors.
The seat and mirror positions can be personalized
for both driver 1 and driver 2. Driver 1 or driver 2
corresponds to the memory buttons labeled 1 and 2
on the control.
The memory function does not store the lumbar or
back support positions.
To set your memory seat and mirrors do the following:
1. Adjust the driver's seat and both outside mirrors to
the desired position.
2. Press and hold the 1 or 2 (driver 1 or 2) button of the
memory control for three seconds. When you hear a
chime ring two times, the memory position is stored.
To do the same thing for a second driver, follow the
preceding steps, but press the other number of the
memory control. The memory feature only works when
the transmission is in PARK (P).
Page 10 of 427
1-4
To recall memory seat and mirror positions, make sure
your vehicle is in PARK (P), then press the 1 or 2 button
of the memory control. You will hear a chime ring one
time to let you know the setting has been selected.
The memory seat and mirror positions can also be
programmed to work with the keyless entry system.
See ªSICº in the Index for more information.
Memory Driver Seat Exit
For this function to work, it must be enabled in the SIC.
See ªSecondary Information Centerº in the Index for
more information.
When this feature is active, it will automatically
(if programmed in the SIC) or manually (when the EXIT
button is pressed) move the driver's seat to a stored exit
position, making it it easier to leave the vehicle.To store the seat exit position for driver 1 or driver 2,
do the following:
1. Select the desired driver number by pressing
the 1 or 2 button.
2. Move the seat to the desired position.
3. Press and hold the EXIT button of the memory
control for three seconds. When you hear a chime
ring two times, the exit position is stored for the
identified driver (driver 1 or 2).
To use the exit feature, do one of the following:
Press the EXIT button on the memory control.
Or, if you have this feature enabled (active) in the
secondary information center, then removing the
key from the ignition will cause the seat to move to
the preset exit position without having to press the
EXIT button.
See ªSecondary Information Centerº in the Index for
more information.
Page 11 of 427
1-5
Memory Seat and Outside Rearview Mirror Recall
You can program your keyless entry transmitter to recall
seat and mirror settings for up to two drivers. Once a
transmitter is programmed, press the UNLOCK button
to recall the seat and mirror settings.
To program a transmitter do the following:
1. Press and hold the desired button 1 or 2 on the
memory controls.
2. Press UNLOCK on the keyless entry transmitter that
corresponds with the specific memory button 1 or 2
pressed in Step 1.
That transmitter will now correspond with the memory
button 1 or 2 and the memory settings that are set for
that number.
Your vehicle comes with two keyless entry transmitters.
The other transmitter may be programmed by following
these steps using the other memory button.Heated Front Seats
The button for the
driver's side heated seat
is located on the driver's
side door panel.
The button for the passenger's side heated seat is located
on the passenger's side door panel. The ignition must be
in RUN for this feature to operate.
To activate the heated seats, press the button once for
the HI (high) heat setting. Press the button again for the
LO (low) heat setting. To turn off the heated seats, press
the button a third time. An indicator light near the button
will illuminate for each heat setting any time the heated
seats are operating.
The heated front seats will be canceled after the ignition
is turned to OFF. If you still want to use the heated front
seat feature after you restart your vehicle, you will need
to press the heated seat button again.
Page 153 of 427
2-87
Sunroof (If Equipped)
Your vehicle may be equipped with a power sliding
sunroof. To open or close your sunroof, the ignition
needs to be on or RAP must be active. See ªRetained
Accessory Powerº in the Index.
Press and release the rear side of the button located in
the front overhead console to express
-open the glass
panel and sunshade. To close the glass panel, press and
hold the front of the button. The glass will not be fully
seated unless the button is held until the glass stops
moving. With the sunroof closed, press the forward side
of the button to open the sunroof to the vent position.The sunroof is also equipped with a sunshade which you
can pull forward to block sun rays.
If a hand, arm, or other object is blocking the sunroof
glass panel as it is closing, the glass panel will stop at
the obstruction. After the obstruction is removed, the
glass panel can be closed or opened.
Use care not to leave the sunroof open for long periods
of time as debris may collect in the tracks.
If the battery has been recharged, disconnected or is not
working, you may need to reprogram the sunroof. To do
this, start the vehicle and press the forward side of the
sunroof button until the glass panel moves to a fully
closed position. Release, and press again to move to the
vent position which occurs when the sunroof is fully
tilted rearward. This will reset the memory and enable
the sunroof to function properly.
Page 188 of 427
2-122
Seat and Mirror Recall
Remote: When the remote keyless entry transmitters
are programmed for each driver (driver 1 or 2),
pressing the UNLOCK button on the transmitter will
move the seat and mirrors to the stored memory
position for the driver associated with that particular
transmitter (driver 1 or 2). For more information on
seat and mirror recall functions, see ªMemory Seat
and Memory Mirrorsº in the Index.
Key In: Inserting the key into the ignition will cause
the seat and mirrors to move to a stored memory
position for driver 1 or 2.
Disabled: Position recall will not work with the
keyless entry transmitter or when the key is placed in
the ignition. Driver must manually select memory
button 1 or 2 to activate the memory seat recall when
disable is selected.Exit Position of Seat
Enabled: Removing the key from the ignition will
move the seat to the stored driver 1 or 2 exit position.
Disabled: The seat will not move to the exit position
when the key is removed from the ignition. Driver
must manually press the EXIT button to activate the
seat exit position feature when disable is selected.
Reverse Mirror Tilt
Passenger: Mirror on the passenger's side of
the vehicle will tilt to a stored memory position
for driver 1 or 2 when the vehicle is placed
in REVERSE (R).
Driver: Mirror on the driver's side of the vehicle
will tilt to a stored memory position for driver 1 or 2
when the vehicle is placed in REVERSE (R).
All: Both the driver's and passenger's side
mirrors will tilt down to a stored memory position
for driver 1 or 2 when the vehicle is placed
in REVERSE (R).
Disabled: No mirrors will tilt when the vehicle is
placed in REVERSE (R).
Page 190 of 427
2-124
Language and Personalization Reset
1. Press and hold the MENU button. After two seconds,
the display will begin cycling through the languages
at one second intervals. Release the MENU button
when the desired language is displayed.
2. The previous action will also reset the
personalization values to their factory default
settings which are as follows.
Automatic Door Lock: Enabled
Automatic Door Unlock: All
Remote Lock Feedback: Horn
Remote Unlock Feedback: Lamps
Headlamp Delay: 30 seconds
Perimeter Lamps: Enabled
Memory Position Recall: Key In
Exit Position of Seat: Enabled
Mirror Reverse Tilt: Passenger
Alarm Warning: Horn and Lamps
Display Units: EnglishUltrasonic Rear Parking Assist (URPA)
Ultrasonic Rear Parking Assist can help you to
determine how close an object is to your rear bumper
within a given area, making parking easier.
The URPA display is
located inside the vehicle,
above the rear window.
It has three color
-coded
lights that can be seen
through the rearview mirror
or by turning around.
URPA can be disabled by
pressing the on/off button
located near the climate
control system and radio.