buttons CADILLAC SEVILLE 1995 4.G Owners Manual

Downloaded from www.Manualslib.com manuals search engine HomeLink TM Universal Transmitter (Option) L
This transmitter allows
you to consolidate
to three individual
hand-held transmitters. It will operate garage
doors and gates, or with
the accessory package,
other devices controlled
as home/office lighting
r the functions of up
I
I by radio frequency such
systems and security
systems.
The transmitter will learn and transmit the frequencies
of most current
- transmitters and is powered by your vehicle’s battery and charging system.
This device complies with Part
15 of the FCC Rules. Operation is subject
to the following
two conditions: (1) This device may not cause harmful
including interference that may cause undesired operation.
- interference, and (2) This device must accept any interference received,
Programming the Transmitter
Do not use the HomeLink” Transmitter with any garage door opener
that does not have the “stop and reverse” safety feature. This includes any
garage door opener model manufactured before April
1,1982.
Be sure that people and objects are clear of the garage dooryou are
programming!
-
r
r Your vehicle’s engine should be turned off while programming your
transmitter. Follow these steps
to program up to three channels:
r
1. If you have previously programmed a HomeLink TM channel, proceed to
Step
2. Otherwise, hold down the two outside buttons on the HomeLink TM
Transmitter until the red light begins to flash rapidly (approximately
20 seconds). Then release the buttons. This procedure initializes the
memory and erases any previous settings for all three channels.
2. Hold the end of your hand-held transmitter against the bottom surface
of the HomeLink“ Transmitter so that you can still see the red light.
r
2-69

Downloaded from www.Manualslib.com manuals search engine 3. Decide which one of the three channels you want to program. Using
both hands, press the hand-held transmitter button and the desired
button on the HomeLink
TM Transmitter. Continue to hold both
buttons through Step
4.
4. Hold down both buttons until you see the red light on the HomeLink“ -
Transmitter flash rapidly. The rapid flashing, which could take up to
90 seconds, indicates that the HomeLink” Transmitter has been
programmed. Release both buttons once
the light starts to flash rapidly. -
If you have trouble programming the HomeLink TM Transmitter, make
sure that you have followed the directions exactly as described and that the
batteries in the hand-held transmitter are not dead. If you still cannot
program it, rotate your hand-held transmitter end over end and try again.
The HomeLink TM Transmitter may not work with older garage door
openers that do not meet current Federal Consumer Safety Standards. If
you cannot program the transmitter after repeated attempts, consult your
Cadillac dealer or call
1-800-355-35 15.
Be sure to keep your original hand-held transmitter in case you need to -
erase and reprogram the HomeLink TM transmitter. -1
Note to Canadian Owners: During programming, your hand-held transmitter
may stop transmitting after one or
two seconds. If you are programming -
from one of these transmitters, the HomeLink indicator light may prompt
you to re-activate your hand-held transmitter
with a series of double blinks.
After you re-activate your hand-held transmitter,
the HomeLink TM light
should flash rapidly.
If it flashes slowly, continue to periodically re-activate
your hand-held transmitter
until the light flashes rapidly.
Operating the Transmitter
Press the appropriate button on the HomeLink TM Universal Transmitter.
The red light comes
on while the signal is being transmitted.
Note that the effective transmission range
of the HomeLink” Transmitter
may differ from your hand-held transmitter and from one channel to another.
-
Emsing Channels
To erase all three programmed channels, hold down the two outside
buttons until the red light begins to flash. Individual channels cannot be
erased,
but can be reprogrammed using the procedure for programming
the transmitter explained earlier.
-
2-70

Downloaded from www.Manualslib.com manuals search engine Driver Information Center Control Buttons
AVG
DtSPtAV
WOFF
TRIP
SET
INFORMATION Button
Pressing the INFORMATION button repeatedly will display the
ENGINE RPM (Digital Cluster only), ENGINE COOLANT TEMP,
BATTERY VOLTAGE, AVG MPH, MPG AVG, FUEL USED, OIL
LIFE
LEFT and TIMER.
RESET Button
Pressing the RESET button will reset the AVG MPH, MPG AVG, FUEL
USED, OIL LIFE LEFT and TIMER when each function is displayed.
TIMER Button
The TIMER feature is like a stopwatch, in that you can clock the time it
takes to get from one point to another.
To operate, press either the TIMER button or successively press the
INFORMATION button
until TIMER 0O:OO:OO is displayed on the Driver
Information Center. Each
of the fields for the HOURS, MINUTES and
SECONDS are two numeric digits.
Once
TIMER 0O:OO:OO is displayed, press the TIMER button to start the
timing feature.
Press the TIMER button again to stop it. If you will be
starting and stopping
your Cadillac, during a trip for instance, the TIMER
feature will automatically start timing where it left off when you last
stopped.
To reset it, press and hold the RESET button until the display
(L4
L.
_4
t
c-
2-88

Downloaded from www.Manualslib.com manuals search engine Driver Information Center Messages
These messages will appear if there is a problem sensed in one of your
vehicle’s systems. Vehicles that are first sold in Canada will have
a number
after each message. This number helps to identify the message which is
only displayed in English.
APPLY BRAKE TO SHIFT - 46
This message will appear if your vehicle is in PARK (P) for about 15
seconds and the brake is not pressed in. If you do not want this message to
appear, you can cancel it by holding the
OFF and the blue (cooler) button
on the Electronic Climate Control panel for about
five seconds. Hold the
same
two buttons again to have this message displayed again.
A/C OVERHEATED - A/C COMPRESSOR OFF - 15
If the refrigerant system ever reaches an over-pressure condition, this
message will appear to tell
you that the air conditioning compressor has
been turned
off. Air conditioned air will not be delivered to cool your
vehicle. If the pressure returns to a normal operating range, you must
select
AUTO, DEFOG or DEFROST to start the compressor. If this
message continues to appear, have the system repaired as soon
as possible
to avoid compressor damage.
BATTERY NO CHARGE - 07
This message will appear if your battery is not being charged. Have your
electrical system checked by your Cadillac dealership at your earliest
convenience.
BATTERY VOLTS HIGH - 08
This message shows that the electrical charging system is overcharging
(more than
16 volts). To avoid being stranded have the electrical system
checked
by your Cadillac dealership. You can reduce the charging
overload by using the accessories. Turn
on the lamps and radio, set the
climate control on
AUTO and the fan speed on HI, and turn the rear
window defogger on.
You can monitor battery voltage on the Driver
Information Center
by toggling the INFORMATION button. The normal
range is
11.5 to 15.5 volts when the engine is running.
c
2-90
-d

Downloaded from www.Manualslib.com manuals search engine TRACTION DISABLED - 88
e-
This message will be displayed if a problem is noted in the Traction
Control System. Have your vehicle serviced as
soon as possible.
TRANS FLUID RESET - 48
With the engine not running and the ignition ON, press and hold the OFF
and REAR DEFOG buttons until the TRANS FLUID RESET message
appears in the Information Center (between five and
20 seconds).
TURN SIGNAL ON - 20
This message is a reminder, after driving about a mile, that you have your
turn signal
on.
TRUNK OPEN - 24
This message indicates that your trunk is open when the ignition is ON.
VERY LOW REFRIGERANT A/C COMPRESSOR OFF - 12
This message means that the Air Conditioning system detects a
refrigerant level that is low enough to cause damage to the A/C
compressor.
To avoid damage, the A/C compressor automatically turns off
and the Electronic Climate Control will automatically switch from AUTO
to ECON and remain there. Have your A/C system serviced if this
message appears.
Speed Sensitive Steering (SSS)
This system varies the amount of steering effort proportionate to your
vehicle speed. Steering
is easier at a lower speed for increased
maneuverability
and parking ease. As your vehicle speed increases, the
steering effort is
also increased proportionately. At highway speeds the
amount
of steering effort is greatly increased to provide a manual-like
steerin.e feel
for maxirnu.m control and enhanced vehicle stability.
2-95

Downloaded from www.Manualslib.com manuals search engine The Oil Life Indicator may say to change the oil sooner than your
maintenance schedule. This can happen
if driving conditions, such as
short trips in cold weather, cause shorter oil life. Always keep a written
record
of the mileage and date when you last changed your oil. For more
Schedule Booklet.
.r-c
- information on when to change your oil, see the Cadillac Maintenance
11 you see CHANGE OIL SOON, it means that you have less than 10% of
If you see CHANGE ENGINE OIL, it means the oil life is gone and you
should change the oil right away (certainly within 200 more miles
[320 km]).
The system should indicate to change the oil between
3,000 miles
(5 000 km) and 7,500 miles (12 500 km), but it may even indicate to
change
it before 3,000 miles under very severe conditions. It all depends
on your driving patterns. If it’s been 7,500 miles (12 500 km) the system
indicates
to change the oil.
-~ your oil life left and you should consider changing your engine oil.
There are two things the system
doesn’t do:
It can’t sense heavy dust in the places where you drive. If you drive in a
dusty area, you should change your
oil every 3,000 miles (5 000 km) or
three months (whichever comes first) unless the display says to change
it even sooner than that.
-- It doesn’t check how much oil you have, so you’ll still have to check for
that.
To see how, see “Engine Oil” in the Index.
-- When You’ve Changed the Oil
When new oil is put in, you’ll need to reset your system. To do this, display
the
OIL LIFE INDEX by pressing the INFORMATION button. Then
LEFT
-- press and hold the RESET buttons until the display shows 100 OIL LIFE
2-97

Downloaded from www.Manualslib.com manuals search engine The Lower Knob
Turn the lower knob to choose radio stations. Press the knob to switch
between
AM and FM.
Behind the lower knob is the fade control. It moves the sound between
the front and rear speakers.
Finding a Station
SCAN When you press this button, up or down, the SCAN indicator in
the display will light and the radio will find the next station and stay there
for about five seconds. Then it will go to the next station and pause, and
keep doing that until you press either the
SCAN button again or the
upper knob.
SEEK This button selects stations, but it doesn’t keep moving as SCAN
does. When you press SEEK, up or down, the radio will automatically go
to the next station and stay there.
-
Pushbuttons: You can set the pushbuttons to get up to 10 favorite stations
(five on FM and five more on
AM).
1. Choose either AM or FM.
2. Tune in a desired station.
3. Press the SET button.
4. Press one of the five pushbuttons within five seconds.
5. Repeat these steps for each of the five pushbuttons.
Setting the Tone
BASS: The slide control increases or decreases the bass response tone.
Moving the control to the right increases bass while moving it
to the left
decreases it.
TREB: The slide control increases or decreases the treble response tone.
Moving the control to the right increases treble while moving it to the left
decreases it.
\,
3-12

Downloaded from www.Manualslib.com manuals search engine --
Your Cassette Tape Player
Your cassette tape player works best with tapes that are 30 to 45 minutes
long on each side. Tapes longer than that are
so thin that they may not
work well in this player.
If you look at the tape, or on its label
or box, it should say whether its bias,
or “equalization,” is
70 microseconds (70 p) or 120 microseconds (120 p).
Chrome and metal tapes are 70 p sec and standard iron tapes are 120 p sec.
Your tape player will adjust automatically for either type of cassette tape.
To Play a Cassette Tape
1. Turn the radio on.
2. Insert the cassette through the tape door. (The TAPE indicator in the
display
will light.)
If you hear nothing or hear just a garbled sound, the cassette may not be
in squarely. Press the EJCT button to remove the tape and start over. The
tape equalization
is automatically sensed and set. Inserting the cassette
also activates DOLBY
@ noise reduction.
DNR@ is the Dynamic Noise Reduction. It helps remove background hiss
noise from the radio.
“DNR’ is a registered trademark of National Semiconductor
Corporation.
3. Once the tape is playing, use the upper and lower knobs to adjust the
volume and balance, just as you do for the radio. Press the upper knob
to change tape direction. The arrow in the display shows which
direction the tape is being played.
FWD: Press this button to go forward rapidly to another part of the tape.
The radio will play during fast forward.
To stop the tape, press the same
button and
the tape will start to play.
REV: Press this button to reverse the tape. To stop the tape, press the
same button lightly or any
of the other buttons. The radio will play during
this reverse function.
3-13

Downloaded from www.Manualslib.com manuals search engine ---
I-
The Upper Knob
The upper knob does the following:
It turns the radio on and off.
It controls the volume.
0 It lets you see what station you have. (When the radio is
RCWPROG knob to display the station.) on,
press the
It tells you the time. (When the ignition is off, press the RCWPROG
0 It allows you to hear the other side of tape play. (When a cassette is
knob
to display the time.)
inserted into the player, press the knob to change sides.)
The Lower Knob
Turn the lower knob to choose radio stations. Press the knob to switch
between
AM and FM.
Behind the lower knob is the fade control. It moves the sound between
the front and rear speakers.
Finding a Station
SCAN When you press this button, the SCAN indicator in the display will
light and the radio will find the next station and stay there for about five
seconds. Then it
will go to the next station and pause, and keep doing that
until
you press either the SCAN button again or the upper knob.
SEEK This button selects stations, but it doesn’t keep moving as SCAN
does. When you press SEEK the radio will automatically go to the next
station and stay there.
Pushbuttons: You can set the pushbuttons to get up to 10 favorite stations
(five
on FM and five more on AM.)
1. Choose either AM or FM.
2. Tune in the station.
3. Press the SET button.
4. Press one of the five pushbuttons within five seconds.
5. Repeat these steps for each of the five pushbuttons.
3- 15

Downloaded from www.Manualslib.com manuals search engine FWD: Press this button to go forward rapidly to another part of the tape.
The radio will play during fast forward.
To stop the tape press the same
button and the tape will start to play.
REV: Press this button to reverse the tape. To stop the tape press the same
button lightly or any
of the other buttons. The radio will play during this
reverse function.
PREV: Press this button to go back to the beginning of the last selection.
If the player has played less than
10 seconds into the current selection,
pressing the PREV button will cause the player to find the beginning of
the previous selection and resume play from that point. If the player is
more than
10 seconds into the current selection, pressing the PREV
button will cause the player to find the beginning of the current selection
and resume play from that point.
If PREV is pressed while the first
selection on the tape is being played, the player will return to the
beginning
of that side of the tape.
NEXT: Press this button to advance to the next selection. If the selection
is at the end of the tape, the tape will reverse directions and begin playing
at a normal speed.
ST/PL Press this button to switch back to the radio without ejecting the
tape. Press it
a second time to start playing the tape again.
EJCT Press this button to remove the tape.
To Play a Compact Disc
Before you begin, please note: don’t use the mini-discs that are called
“singles” (even with an adapter). They won’t eject. Use full-size compact
discs only.
1. Turn the radio on.
2. Insert a CD (label side up) partway into the slot. The player will pull it
in.
Wait a few seconds and the CD will play. Then only the time of day
and
CD will display.
If the
CD comes back out, check to see if
0 The disc is upside down.
0 The disc is dirty, scratched or wet.
0 There’s too much moisture in the air. If there is, wait about one hour
and
try it again.