buttons CADILLAC SEVILLE 1996 4.G Owners Manual

Downloaded from www.Manualslib.com manuals search engine L
#--
Memory Seat (Option)
Adjust the driver’s seat to a
comfortable position and
then press the
SET button.
Within five seconds, press
button
“1 .” A second
seating position may be
programmed by repeating
the above steps and pressing
button
“2” instead of
Note that each time a memory button is pressed a single
beep will sound through the radio.
If your vehicle is in PARK (P), you can recall a seating
position by briefly pressing button
1 or 2. This will
adjust
the seat to where you have previously
programmed it.
If you have accidently pressed one
of the memory recall buttons and want to stop seat
movement, press one
of the manual seat control buttons.
This cancels a memory seat recall.
c
c
You can also recall a seat position if your vehicle is not
in PARK
(P). Press and hold either the 1 or 2 button until seat movement
is complete.
Releasing the buttons
will stop seat adjustment.
The
EXIT button can be programmed to allow easy exit
for up to two driver’s. Adjust the seat to a comfortable
“exit” position and press the SET button followed by
the EXIT button. Within five seconds, press button
1.
A second exit position may be programmed by repeating
the above steps and pressing button
2 instead of button
1. Be aware that the exit recall does not remember any
recline positions.
While your vehicle is in PARK
(P), briefly press the
EXIT button followed by either the
1 or 2 button to
recall your programmed exit position. The exit position
may also be recalled
if the vehicle is not in PARK (P) by
briefly pressing the
EXIT button and then pressing and
holding either the
1 or 2 button until seat movement is
complete. Releasing the buttons will stop seat
adjustment.
Automatic seat movement will occur if the Remote
Keyless Entry
(RKE) transmitter is used to enter the
vehicle. The number on the back
of the transmitter
corresponds to the
1 or 2 seat position. After the unlock
button is pressed on the RKE transmitter and the key is
placed in
the ignition and turned on, the seat will
automatically adjust to the appropriate position.
1-3

Downloaded from www.Manualslib.com manuals search engine c
c-
To begin programming, press the INFO and RESET
buttons at the same time. The first prompt
to appear is
AUTOMATIC DOOR LOCK?. You must press the
RESET button when this prompt appears to continue
programming the doors. The next prompt to appear is
ENABLE ALL DOORS FOR LOCK AND UNLOCK?.
This selection locks all doors when shifting
out of
PARK (P) and unlocks all doors when shifting back into
PARK
(P). DISABLE ALL DOORS FOR LOCK AND
UNLOCK?
is used when you do not want any automatic
lock functions. The ENABLE ALL
LOCKS AND
DRIVER DOOR UNLOCK? prompt locks all doors
when shifting out
of PARK (P) and unlocks only the
driver‘s door when shifting back into PARK (P).
ENABLE ALL DOORS FOR
LOCK ONLY? selection
appears next.
This prompt is used to lock all doors when
shifting out
of PARK (P) and keeps the doors locked
when you shift back into
PARK (P).
A yes or no response must be programmed when a
prompt is displayed. A yes response selects the prompt
and a no response displays the next prompt.
When you finish programming the door
locks, the next
prompt
to appear is for the vehicle storage mode. For
more information on vehicle storage, see “Battery Guard
Storage” later in this section.
Rear Door Security Locks
b
Your Cadillac is equipped
with rear door security
locks that help prevent
passengers from opening
the rear doors
of your
vehicle from the inside.
To
use this lock:
1. Move the lever on the door all the way up to the
ENGAGED position.
2. Close the door.
3. Do the same thing to the other rear door lock.
The rear doors
of your vehicle cannot be opened from
the inside when this feature
is in use.
2-5

Downloaded from www.Manualslib.com manuals search engine 8 When you press this symbol to lock the doors, the
parking lamps will blink once. This also
arms the
optional theft-deterrent system.
a Press this symbol to open the trunk.
Press this button to
open the fuel door.
The Keyless Entry transmitter can also be used to recall
the memory seats
for up to two drivers. For more
information, see “Memory Seat” in the Index.
Note that pressing the transmitter buttons numerous times
(approximately
500 times) out of the vehicle’s operating
range may cause the transmitter not to
work. Replacing
the battery and pressing the transmitter buttons
10 or
more times out
of range will also cause the transmitter not to work.
To reset the transmitter, you must be within
the vehicle’s operating range.
Press and hold the trunk
button and within one second press the lock button.
Continue to hold both buttons
for approximately three
seconds. See your Cadillac dealer for service if your
transmitter still doesn’t work properly.
Matching Transmitter(s) To Your Vehicle
Each key chain transmitter is coded to prevent another
transmitter from unlocking your vehicle.
If a transmitter
is lost
or stolen, a replacement can be purchased through
your dealer. Once the new transmitter is coded, the
lost
transmitter will not unlock your vehicle. Each vehicle
can have only two transmitters matched to it.
2-8

Downloaded from www.Manualslib.com manuals search engine h
L
Reading Lamps
i
The reading lamps are located in the roof. These lamps
and the interior courtesy lamps come on when any door
is opened and it is dark outside. Press the button to turn
them on. Press it again
to turn them off.
If the reading lamps are left on, they automatically shut
off 10 minutes after the ignition has been turned off.
Inadvertent Power Battery Saver
This feature is designed to protect your vehicle's battery
against drainage from the interior lamps, trunk.lamp,
glove
box lamp, cigarette lighters or the garage door
opener. When
the ignition is turned OFF, the power
to these features will automatically
turn off after
10 minutes (three minutes if a new car has 15 miles
or
Iess). Power will be restored for an additional
10 minutes if any door is opened, the trunk is opened
or the courtesy lamp switch
is turned on.
Battery Guard Storage
This feature is for long term use. and must be
programmed through the
DIC while the ignition is in
the RUN position. Battery guard storage protects the
battery by placing the vehicle
in a storage mode so that
the radio, amplifiers, instrument cluster and Remote
Keyless Entry
(RKE) will not drain the battery over a
long period of time.
To begin programming, press the INFO and RESET
buttons at the same time for approximately two seconds.
Press the
RESET button to answer "yes" and press the
INFO button to indicate a "no" response.
2-45

Downloaded from www.Manualslib.com manuals search engine Your vehicle’s engine should be turned off while
programming the transmitter. Follow these steps to
program up to three channels:
1. If you have not previously programmed a universal
channel, proceed to Step
2. Otherwise, hold down
the two outside buttons on the universal transmitter
until the red light begins to flash rapidly
(approximately
20 seconds). Then release the
buttons. This procedure initializes the memory and
erases any previous settings for
all three channels.
2. Hold the end of the hand-held transmitter against the
bottom surface of the universal transmitter
so that
you can still see the red light.
3. Decide which one of the three channels you want to
program. Using both hands, press the hand-held
transmitter button and the desired button on the
universal transmitter. Continue to hold both buttons
through Step
4.
4. Hold down both buttons until you see the red light
on the universal transmitter flash rapidly and then
stop. The rapid flashing, which could take up to
90 seconds, indicates that the universal transmitter
has been programmed. Release both buttons once the
light starts to flash rapidly.
If you have trouble programming the universal
transmitter, make sure that
you have followed the
directions exactly
as described and that the battery in the
hand-held transmitter is not dead.
If you still cannot
program it, rotate the hand-held transmitter end over end
and
try again. The universal transmitter may not work
with older garage door openers that do
not meet current
Federal Consumer Safety Standards.
If you cannot
program the transmitter after repeated attempts, consult
your Cadillac dealer.
Be sure to keep the original hand-held transmitter in
case
you need to erase and reprogram the universal
transmitter.
Note to Canadian Owners: During programming, the
hand-held transmitter may stop transmitting after one or
two seconds.
If you are programming from one of these
transmitters, you should
press and repress the button on
the hand-held transmitter every two seconds without
ever releasing the button on the universal transmitter.
Release both buttons when the red light
on the universal
transmitter begins to flash rapidly.
2-58
a
I

Downloaded from www.Manualslib.com manuals search engine IL
Operating the Transmitter
Press and hold the appropriate button on the universal
transmitter. The red light comes
on while the signal
is being transmitted.
Note that
the effective transmission range of the
universal transmitter may differ from the hand-held
transmitter and from
one channel to another. Also
note that
the universal transmitter is disabled when
the
VALET button inside of the glove box is activated
for more information, see “Security Override” earlier
in this section.
Erasing Channels
To erase all three programmed channels, hold down the
two outside buttons until the red light begins to
flash.
Individual channels cannot be erased, but can be
reprogrammed using the procedure for programming the
transmitter explained earlier.
Accessories
Accessories for the universal transmitter are available
from the manufacturer
of the unit. If you would like
additional information please call
1-800-355-35 15.

Downloaded from www.Manualslib.com manuals search engine c
The instrument panel is designed to let you know at a
glance how your Cadillac is running. You’ll
know how
fast you’re going, how much fuel you’re using and
many
of the other things you’ll need to know to drive
safely and economically. The main components
of the
instrument panel are:
1. Air Outlets
[Wb
2. Turn Signal/Multifunction Lever
3. Driver Information Center Control Buttons
4. Driver’s Side Air Bag
5. Cluster
6. Steering Column Shift Lever
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
Electronic Climate Controls
Audio System
Passenger’s Side
Air Bag
Lamp Controls Steering Wheel Touch Controls for Climate Control
Hood Release
Horn
Steering Wheel Touch Controls for Audio System
Astray and Cigarette Lighter
Glove
Box
2-61

Downloaded from www.Manualslib.com manuals search engine c
Driver Information Center (DIC)
The DIC display gives you the status of many of your
vehicle’s systems. The
DIC is used to display driver
selectable information and warning/status messages.
If more than one problem is detected, the DIC will
automatically display all current messages.
Digital Control Buttons
,
DISPLAY ON/OFF: Pressing this button will turn off
the DIC, Electronic Climate Control, fuel data center,
the fuel gage, trip odometer and odometer. While the
displays are
off, pressing the INFORMATION button
will only turn
on the DIC. If the TRIP SET button
is pressed
or the fuel level falls below four gallons
(15.2 L), all the displays will come back on.
ENG/MET (EnglishIMetric): You can change the
display from English (miles)
to metric (kilometers) by
pressing this button. The same button also changes other
readings (like temperature, fuel and odometer).
TRIP SET By using this button you can tell how far
you’ve gone since
you last set the TRIP SET back to
zero. To reset, press and hold the button until zeros
appear. If your vehicle is domestic, the trip odometer
will return
to zero after 999.9 miles (1 609 kmj. If your
vehicle
is Canadian, the trip odometer will return to zero
after
1 999.9 km (1,242 miles j.
INFORMATION: Pressing this button repeatedly will
display
the AVG MPG, FUEL USED, AVG MPH, OIL
LIFE LEFT, ENGINE RPM, BATTERY VOLTS and
COOLANT TEMP.
2-77

Downloaded from www.Manualslib.com manuals search engine Analog Control Buttons
INFO RESET Pressing this button will reset the MPG
AVG, FUEL USED, AVG MPH, TIMER, OIL LIFE
LEFT and ENGLISHMETRIC RESET. Pressing INFO
RESET when a non-resettable display appears will
cause a “recall” mode
to occur. When this happens, all
DIC warning messages that have
been displayed since
the ignition key was turned
to RUN will redisplay. If no
messages were displayed,
a MONITORED SYSTEMS
OK message will appear.
MPG AVG (Average Fuel Economy) Reset: Press
the
INFO button to display the MPG AVG, then press
and
hold the INFO RESET button until 0.0 MPG AVG
is displayed.
Fuel Used Reset: Press the INFO button to display the
FUEL USED
on the DIC, then press and hold the INFO
RESET button until FUEL USED 0.0 is displayed.
AVG MPH (Average Speed) Reset: Press the INFO
button
to display the AVG MPH, then press and hold the
INFO RESET button
until 0.0 AVG MPH is displayed.
Timer: This feature is like a stopwatch, in that you can
clock the time it takes
to get from one point to another.
To operate, press the INFO button
to display TIMER.
Each
of the fields for the hours. minutes and seconds are
two numeric digits.
Once TIMER OFF
0O:OO:OO is displayed, press the
INFO RESET button to start the timing feature. Press
the INFO RESET button again to
stop it. If you will be
starting and stopping your Cadillac, during
a trip for
instance,
the TIMER feature will automatically start
timing where it left off when
you last stopped. To reset
it, press and hold the INFO RESET button until the
display reads TIMER
0O:OO:OO. Press the INFO button
to exit from the TIMER function.
2-79

Downloaded from www.Manualslib.com manuals search engine Oil Life Left Reset: Press the INFO button to display
the
OIL LIFE LEFT, then press and hold the INFO
RESET button until
100% OIL LIFE LEFT is displayed.
English/Metric Reset: Press the INFO button to display
ENGLISHMETRIC
RESET, then press the INFO
RESET button to select. The display will change from
English (miles) to metric (kilometers).
TRIP RESET By using this button you can tell how far
you've gone since you last set the TRIP RESET back to
zero. To reset,' press and hold the button until zeros
appear.
If your vehicle is domestic, the trip odometer
will return to zero after 999.9 miles
(1 609 km). If your
vehicle is Canadian, the trip odometer will return to zero
after
1 999.9 km (1,242 L miles).
INFO: Pressing this button repeatedly will display the
RANGE, MPG AVG, MPG INST, FUEL USED, AVG
MPH, TIMER, OIL LIFE LEFT, BATTERY VOLTS
and ENGLISHMETRIC RESET.
FUEL DOOR: Press this button to open the fuel door.
TRUNK: Press this button to open the trunk.
Driver Information Center Messages
These messages will appear if there is a problem sensed
in one
of your vehicle's systems. Vehicles that are first
sold in Canada will have a number after each message.
This number helps to identify the message which is only
displayed in English.
message displays when the engine coolant becomes hotter
than the normal operating temperature.
To avoid added
strain on a hot engine, the air conditioning compressor is
automatically turned off so that air conditioned air is not
delivered.
If the coolant temperature rems to normal, you
must select
AC to return to a normal A/C compressor
operation.
If this message continues to appear, have the
system repaired as soon as possible to avoid compressor
damage.
A/C OFF FOR ENGINE PROTECTION - 16: "his
APPLY BRAKE TO SHIFT - 46: This message will
appear if your vehicle is in PARK (P) for about 15 seconds
and
the brake is not pressed in. Remove the message by
holding the
OFF and the blue (cooler) button on the
Electronic Climate Control panel for about five seconds.
Hold the same two buttons again to redisplay
the message.
2-80