display CADILLAC SEVILLE 2000 5.G Repair Manual

3-44
The Setup Wizard will guide you through the steps to
create an e
-mail service. You may need to contact your
ISP for the information required to complete the setup.
Receiving and Sending E-Mail
Your radio uses the cellular phone to connect to your
ISP. Make sure the phone is secure and connected.
Begin the modem session by connecting the modem
cable (or serial cable with a null modem) to your
computing device. Press and release the modem door on
the radio near the recessed bumps. Connect the cable to
the radio's 25
-pin connector. Start your e-mail program
and connect to the ISP. The radio will receive the phone
number from your PDA and instruct the phone to dial
the number. While connecting, the audio from your
radio will be briefly muted and you will hear the tones
being generated as the modem establishes a connection.
When the connection is complete, the audio will return.
When you end your e
-mail session your radio will
instruct the phone to hang up.
Cellular Phone Reception
If the reception of the cellular signal weakens the error
rate of the modem will increase. If you are having
difficulty connecting or sending and receiving data the
cellular signal may be too weak. To ensure good signal conditions, the cell phone display should show
a minimum of three to four bars for signal strength.
The volume on the phone handset should be set to
three bars for best results.
Text Based Information Services
Your radio can be used to gather information using
enhanced Radio Data Systems (RDS) while you are out of
the vehicle. The radio can provide text
-based information
such as traffic and weather. This is done through a
nationwide network of FM stations. You do not need to
know which station is providing this service, the radio will
search out the station when not being used. Your dealer
can provide details on how to obtain this service.
You can program the radio to automatically wake up
twice daily, for example, at 7 AM and again at 4:30 PM.
If your vehicle is off, the radio will wake up at these
programmed times to gather the information. Although
the radio is awake and receiving data, it will appear to
be off. There will be no sound or display. It may take
up to 15 minutes for each update. The information
will then be available for review when you enter your
vehicle. If the vehicle is on at the time of the scheduled
update, the update will not be performed. In addition
to the user programmable times, the system will
automatically update the information when you turn
the ignition off and leave the vehicle.

3-45 Programming for News/Information Updates
Your vehicle is delivered with the Communiport
Infotainment radio programmable updates off. You
can program the radio to provide two daily updates.
To program the update times follow these steps:
1. Press and hold the INFO button for approximately
two seconds. This will cause the radio to enter the
programming mode.
2. Press and release the INFO button, UPDATE 1
TIME will appear on the display. Use the HR and
MN buttons to set the time you would like to retrieve
the first news and information update.
3. Press and release the INFO button again, UPDATE
2 TIME will appear on the display. Use the HR and
MN buttons to set the time to retrieve the second
daily news and information update.
The HR button can be used to select OFF if one or both
automatic updates are not required.
If you have not started your vehicle in a couple of days
the radio will switch to a reduced update schedule by
skipping every other update time. After approximately
three days the radio will stop providing information
updates until you restart your vehicle. This is intended
to conserve your vehicle's battery.
Programming for an Immediate
Information Update
To program an immediate news update, press and hold
the INFO button until UPDATE NOW? PRESS RDM
appears on the display. Then press the RDM button while
UPDATE NOW? PRESS RDM is being displayed.
The radio will begin the update by switching to the
FM band, if not already there, and tuning to the service
provider's station. If you are listening to AM, FM or
weather, UPDATING INFO.... will appear on the
display until the update has completed. You can switch
the source to cassette or CD changer or turn the radio
off without interrupting the update.
You can also perform the update while listening to the
cassette player or CD changer. The radio will briefly
display UPDATING INFO...., then return to the
normal display. The radio will beep once to let you
know when the update has completed.
To cancel the update and return to the station you were
listening to, turn the radio off and back on again.

3-46
While performing the information update, the radio will
temporarily disable the RDS buttons. The RDS buttons
will be enabled again once the update is completed.
When the radio begins an update, the information
contained in the radio's memory is cleared. If you
perform an immediate update and then quickly cancel it,
NO TEXT AVAILABLE will appear on the display.
Viewing the News/Information
To view the news/information, press and release the
INFO button. The radio will display TOPIC: ALL.
The radio will then begin displaying all the received
information at a rate of approximately three seconds
per display. You can page through the topics at a faster
rate by pressing and releasing the INFO button after
the text appears.
You can access a topic directly from the TOPIC: ALL
display by pressing and releasing the INFO button until
the desired topic is displayed. The radio will display the
information for that topic only.
If the radio has not received any information, NO TEXT
AVAILABLE will appear on the display. This will be
followed by the UPDATE NOW? PRESS RDM display
previously described.
Vehicle Control
Your radio can provide you with safety and convenience
features by performing the following vehicle control actions:

Unlocking or locking the doors,

opening the trunk,

flashing the parking lights and

sounding the horn.
If you need one of these services, contact the OnStar

service center.
When you turn your vehicle off, the radio will
automatically tune to your FM provider's station and
check for a vehicle control request received through
RDS. Your vehicle control request will be completed in
five minutes or less if your vehicle is in the continental
United States and in a location that can receive
FM broadcasts.
Vehicle control is available for six days from the time
you last turned off your vehicle. This time can be
increased up to 11 days by turning off the automatic
information updates as described previously. This would
be useful if you are going to be away from your vehicle
for an extended period of time.
For more information see OnStar in the Index.

3-48
Navigation/Radio System (Option)
Navigation/Radio Display and Controls
The display screen is located in the center of the
instrument panel. There are eight ªhardº buttons and a
touch sensitive screen.Your vehicle may be equipped with an AM
-FM stereo
navigation radio system that includes digital sound
processing (DSP), a Radio Data System (RDS) with
program ªtypeº selections (PTY) that will seek out
the kind of music you want to listen to. The radio
system can also communicate with your navigation
system to broadcast announcements on traffic, weather
and emergency alert communications. For information
on how to use this system, see ªNavigation/Radio
Systemº supplement.
CD Adapter Kits
It is possible to use a portable CD player adapter kit
with your cassette tape player after activating the bypass
feature on your tape player.
To activate the bypass feature, use the following steps:
1. Turn the ignition to ON or ACC.
2. Turn the radio off.
3. Press and hold the SOURCE button for two seconds.
The tape symbol on the display will flash three
times, indicating the feature is active.
4. Insert the adapter into the cassette slot.
This override routine will remain active until the eject
button is pressed.

3-49 Console-Mounted CD Changer (Option)
With the compact disc changer, you can play up to six
discs continuously. Normal size discs may be played
using the slots supplied in the magazine.
You must first load the magazine with discs before you
can play a compact disc. Load the CDs from bottom to
top, placing a disc in the magazine label side up. If you
load a disc label side down, the disc will not play and an
error will occur. Repeat this procedure for loading up to
six discs in the magazine.Once you have loaded the discs in the magazine,
slide open the door of the compact disc (CD) changer.
Push the magazine into the changer in the direction of
the arrow marked on top of the magazine.
Close the door by sliding it all the way forward. When
the CD magazine is loaded, the changer will begin
checking for discs in the magazine. This will continue
for up to one minute, depending on the number of
discs loaded.
To eject the magazine from the player, slide the CD
changer door all the way open, then press the eject
button. Remember to keep the door closed whenever
possible to keep dirt and dust from getting inside
the changer.
Whenever a CD magazine with discs is loaded in the
changer, the CD changer symbol will appear on the
radio display. If the CD changer is checking the
magazine for CDs, the CD symbol will flash on the
display until the changer is ready to play. When a
CD begins playing, a disc and track number will be
displayed. The disc numbers are listed on the front
of the magazine.
All of the CD functions are controlled by the radio
buttons, except for ejecting the CD magazine.

3-50
PUSHBUTTONS: Press buttons one through six to
select compact discs one through six. These pushbuttons
represent the order of the discs loaded in the changer.
RW: Press and hold this button to reverse quickly
through a track selection.
FF: Press and hold this button to advance quickly
through a track selection.
TUNE
-SEEK: When this button is pressed, it has
two positions. This button works the same, whether
it is pressed to the first or second position. Press this
button to seek to the next or previous selection on the
compact disc.
TRACK SCAN: When you press SCAN for less than
two seconds, you will hear the first few seconds of each
track on a disc. Press SCAN again to stop TRACK
SCAN. The CD will mute while scanning and SCAN
will appear on the display.
DISC SCAN: When you press SCAN for more than
two seconds, you will hear the first few seconds of the
first track on each disc. Press SCAN again to stop
DISC SCAN. The CD will mute while scanning and
SCAN will appear on the display.RDM: Press this button to hear the tracks in random,
rather than sequential, order. RANDOM will appear on
the display. Press TUNE
-SEEK while RDM is on the
display to randomly seek through discs. Press RDM
again to turn off random play.
SIDE: Press this button to select the next disc in
the changer. Each time you press this button, DISC
LOADING will appear on the display and the disc
number on the radio display will go to that of the next
available CD.
SOURCE: Press this button to select a source. The
audio source must be loaded to play. If none of the audio
sources are loaded, NO SOURCE LOADED will appear
on the display. Press this button again or press BAND to
switch back to the radio.
EJECT: Slide the CD changer door all the way
open. Press the upward triangle button. The CD
magazine will eject.

3-51
Compact Disc Changer Errors
CD CHANGER ERROR could be displayed for
the following:

The road is too rough. The disc should play when
the road is smoother.

The disc is dirty, scratched, wet or loaded label
side down.

The air is very humid. If so, wait about an hour
and try again.
If any error occurs repeatedly or if an error cannot be
corrected, please contact your dealer.
Radio Personalization with Home and
Away Feature (If Equipped)
If DRIVER 1 (HOME or AWAY) PRESETS or
DRIVER 2 (HOME or AWAY) PRESETS appears
in the display when the radio is first turned on, your
vehicle is equipped with this feature.
With this feature, your vehicle will recall the latest radio
settings as adjusted the last time your vehicle was
operated. This feature allows two different drivers to
store and recall their own radio settings. The settings
recalled by the radio are determined by which RKE
transmitter (ª1º or ª2º) was used to enter the
vehicle. The number on the back of the RKE transmitter
corresponds to driver 1 or to driver 2. The radio settings
will automatically adjust to where they were last set by
the identified driver. The settings can also be recalled by
briefly pressing the MEMORY seat buttons 1 or 2
located on the driver's door.
Your radio can store home and away presets. Home and
away presets allow you to use one set of preset radio
settings in the area where you live, and another set when
you go out of town. That way, you will not need to
reprogram your presets every time you travel. With the
radio off and the clock displayed, use FF and RW to
select home or away presets. To select the away presets,
press and hold FF for five counts until you hear a beep.
The next time the radio comes on, the away presets will
be active. To select the home presets, press and hold
RW for five counts until you hear a beep. The next time
the radio comes on, the home presets will be active.
When battery power is removed and later applied, you
will not have to reset your home radio presets because
the radio remembers them. However, you will have to
reset your away radio presets.

3-53
SEL: When listening to the radio, press the up or down
arrow button to tune to the next or previous preset radio
station. When listening to a cassette tape, the up or down
arrow button can be used to SEEK forward and rearward
through the tape. Pressing the up or down arrow button
when listening to a CD will cause the player to go to the
next or previous selection. When in Radio Data Systems
(RDS) Program Type (PTY) mode, the up or down
arrow button can be used to perform a PTY preset seek.
PSEEK will appear on the display while the PTY preset
seek is performed. The radio will seek all of the PTYs
stored in presets, except for the PTY Any.
Understanding Radio Reception
AM
The range for most AM stations is greater than for FM,
especially at night. The longer range, however, can
cause stations to interfere with each other. AM can pick
up noise from things like storms and power lines. Try
reducing the treble to reduce this noise if you ever get it.FM Stereo
FM stereo will give you the best sound, but FM signals
will reach only about 10 to 40 miles (16 to 65 km). Tall
buildings or hills can interfere with FM signals, causing
the sound to come and go.
Weather Band (If Equipped)
Weather band is restricted to speech and the audio
quality is not as good as with the AM or FM bands.
Depending on location, the radio should receive one or
two channels.
Tips About Your Audio System
Hearing damage from loud noise is almost undetectable
until it is too late. Your hearing can adapt to higher
volumes of sound. Sound that seems normal can be
loud and harmful to your hearing. Take precautions by
adjusting the volume control on your radio to a safe
sound level before your hearing adapts to it.

3-54
To help avoid hearing loss or damage:

Adjust the volume control to the lowest setting.

Increase volume slowly until you hear comfortably
and clearly.
NOTICE:
Before you add any sound equipment to your
vehicle
-- like a tape player, CB radio, mobile
telephone or two
-way radio -- be sure you
can add what you want. If you can, it's very
important to do it properly. Added sound
equipment may interfere with the operation of
your vehicle's engine, radio or other systems,
and even damage them. Your vehicle's systems
may also interfere with the operation of sound
equipment that has been added improperly.
So, before adding sound equipment, check with
your dealer and be sure to check Federal rules
covering mobile radio and telephone units.
Care of Your Cassette Tape Player
A tape player that is not cleaned regularly can cause
reduced sound quality, ruined cassettes or a damaged
mechanism. Cassette tapes should be stored in their
cases away from contaminants, direct sunlight and
extreme heat. If they aren't, they may not operate
properly or may cause failure of the tape player.
Your tape player should be cleaned regularly after every
50 hours of use. Your radio may display CLEAN TAPE
to indicate that you have used your tape player for
50 hours without resetting the tape clean timer. If this
message appears on the display, your cassette tape
player needs to be cleaned. It will still play tapes, but
you should clean it as soon as possible to prevent
damage to your tapes and player. If you notice a
reduction in sound quality, try a known good cassette
to see if it is the tape or the tape player at fault. If this
other cassette has no improvement in sound quality,
clean the tape player.
The recommended cleaning method for your
cassette tape player is the use of a scrubbing action,
non
-abrasive cleaning cassette with pads which scrub
the tape head as the hubs of the cleaner cassette turn.
The recommended cleaning cassette is available through
your dealership (GM Part No. 12344789).

3-55
When using a scrubbing action, non-abrasive cleaning
cassette, it is normal for the cassette to eject because
your unit is equipped with a cut tape detection feature
and a cleaning cassette may appear as a broken tape.
To prevent the cleaning cassette from being ejected, use
the following steps.
1. Turn the ignition to ON or ACC.
2. Turn the radio off.
3. Press and hold the SOURCE button for two
seconds. The tape symbol on the display will flash
three times.
4. Turn the radio on and insert the scrubbing action
cleaning cassette.
5. Eject the cleaning cassette after the manufacturer's
recommended cleaning time.
When the cleaning cassette has been ejected, the cut tape
detection feature is active again.
You may also choose a non
-scrubbing action, wet-type
cleaner which uses a cassette with a fabric belt to clean
the tape head. This type of cleaning cassette will not
eject on its own. A non
-scrubbing action cleaner may
not clean as thoroughly as the scrubbing type cleaner.
The use of a non
-scrubbing action, dry-type cleaning
cassette is not recommended.After you clean the player, press and hold the eject
button for three seconds to reset the CLEAN TAPE
indicator. The radio will display CLEAN TAPE MSG
CLEARED to show the indicator was reset.
Cassettes are subject to wear and the sound quality may
degrade over time. Always make sure the cassette tape
is in good condition before you have your tape
player serviced.
Care of Your Compact Discs
Handle discs carefully. Store them in their original cases
or other protective cases and away from direct sunlight
and dust. If the surface of a disc is soiled, dampen a
clean, soft cloth in a mild, neutral detergent solution
and clean it, wiping from the center to the edge.
Be sure never to touch the signal surface when handling
discs. Pick up discs by grasping the outer edges or the
edge of the hole and the outer edge.
Care of Your Compact Disc Player
The use of CD lens cleaner discs is not advised, due to
the risk of contaminating the lens of the CD optics with
lubricants internal to the CD mechanism.