oil pressure CHEVROLET C/K 2003 User Guide

7-11
67,500 Miles (108 000 km)
Gasoline Engine Only: Check Oil Life System.
If engine oil and filter are changed, reset system.
See ªEngine Oilº in the Index. (3)(9)
Check fluid levels (or every 3 months, whichever
occurs first). (1)(6)
Chassis lubrication service (or every 6 months,
whichever occurs first). (12)
Cooling system service. Clean the cooling system
filler cap with clean water, clean the core, pressure
test the cap and the system for proper pressure
capability and inspect condition of cooling and
heater hoses and clamps. Replace hoses if cracked,
swollen or damaged.
Wheel bearing (grease type) service (or every
24 months, whichever occurs first, and whenever
hubs are removed). (23)(46)
Wheels and tires service. (15)
Parking brake service (or every 6 months, whichever
occurs first). (8)
Rear axle air shift motor service. (11)
Air intake system service (or every 24 months,
whichever occurs first). (4)(5)(24)Evaporative Control System service (if equipped) (or
every 24 months, whichever occurs first). (3)(26)

Air brake service (or every 6 months, whichever
occurs first). (39)
Air brake automatic slack adjuster service (or every
500 hours, whichever occurs first). (40)
Check air brake relay valve operation and check
for leaks (or every month, or every 300 hours,
whichever occurs first).
Clean air brake application valve (or every 3 months,
or every 300 hours, whichever occurs first); lubricate
linkage.
Air brake chamber service (or every 2 months,
whichever occurs first). (41)
Trailer brake hand control valve service
(or every 3 months, or every 900 hours,
whichever occurs first). (42)
L18/LB7 Engines Only: Clutch pedal free
travel service. (10)
70,000 Miles (112 000 km)
DURAMAX Diesel Only: Change engine
oil and filter (or every 12 months, whichever
occurs first). (2)(3)

7-13
90,000 Miles (144 000 km)

Gasoline Engine Only: Check Oil Life System.
If engine oil and filter are changed, reset system.
See ªEngine Oilº in the Index. (3)(9)

DURAMAX Diesel Only: Change engine
oil and filter (or every 12 months, whichever
occurs first). (2)(3)

Check fluid levels (or every 3 months, whichever
occurs first). (1)(6)

DURAMAX Diesel Only: Replace fuel filter.

Chassis lubrication service (or every 6 months,
whichever occurs first). (12)

Cooling system service. Clean the cooling system
filler cap with clean water, clean the core, pressure
test the cap and the system for proper pressure
capability and inspect condition of cooling and
heater hoses and clamps. Replace hoses if cracked,
swollen or damaged.

Wheel bearing (grease type) service (or every
24 months, whichever occurs first, and whenever
hubs are removed). (23)(46)

Replace fuel filter(s) (or every 12 months, whichever
occurs first). (3)
Steering system service. (13)

Front and rear suspension service. (14)

Spring
-to-axle U-bolts and shackle
bolts service. (16)

Exhaust system service (or every 6 months,
whichever occurs first). (3)(4)(17)

Inspect door hinge pins and bushings and replace
as necessary.

Wheels and tires service. (15)

Hydraulic brake service (or every 6 months,
whichever occurs first). (7)(46)

Parking brake service (or every 6 months, whichever
occurs first). (8)

C600, C700 and C800 Gasoline Engines Only:
Engine drive belts service (or every 12 months,
whichever occurs first). (18)

Thermostatically controlled engine cooling fan
service. (4)(20)

Shields and underhood insulation service. (4)(5)(21)

Rear axle air shift motor service. (11)

Air intake system service (or every 24 months,
whichever occurs first). (4)(5)(24)
(Continued)

7-17
(10) = Check clutch pedal for free travel. Press pedal
by hand until resistance is felt. Free travel should be
maintained at 1.5 to 2 inches (38 to 51 mm) measured
at the clutch pedal pad. Make checks at 1,000 miles
(1 600 km) and then at every 7,500 mile (12 000 km)
interval thereafter.
(11) = Inspect rear axle air shift motor for fluid leaks.
Remove plug to check fluid level. Inspect air lines and
hoses for proper hook
-up, binding, leaks, etc. Inspect at
3,000 miles (5 000 km) and 22,500 miles (36 000 km)
and then every 22,500 miles (36 000 km) thereafter.
(12) = Chassis Lubrication Service: Lubricate all grease
fittings in front suspension, front axle and steering
linkage. DO NOT lubricate kingpin bushings with air
pressure equipment; instead, use a hand grease gun to
ensure complete purge and eliminate sealer cap
distortion. Lubricate transmission and shift linkage,
hood latches and hood hinges, parking brake lever pivot,
clevis pins and linkage, disc brake caliper rails, clutch
linkage and release bearing (if equipped), bearing pads,
propshaft universal joints, brake camshaft bracket, slack
adjusters, pedal shaft, clutch cross shaft and clutch pedal
springs. Lubricate suspension, axle and steering linkage
more often when operating under dusty or muddy
conditions and in excessive off
-road use.(13) = Check steering system:

Look for damaged, loose or missing parts. Also look
for parts showing signs of wear or lack of lubrication.
Replace parts as needed. Also check steering gear
mounting bolts, pitman arm nut, gear housing upper
cover and side cover attaching bolts, steering column
mounting bolts and cardan joint clamp bolts; tighten
if necessary. (See service manual.)

Inspect power steering hoses, tubes and fittings for
leaks. Hoses and lines must not be twisted, kinked or
tightly bent. Make sure clips, clamps, supporting
tubes and hoses are in place and properly secured.

Check steering gear for leakage around pitman shaft
and housing. If leakage is evident (lubricant oozing
out, not just oily film), leak should be corrected
immediately.
(14) = Check front and rear suspension. Look for
damaged, loose or missing parts or parts showing signs
of wear or lack of lubrication. Replace parts as needed.

7-18
(15) = Adjust tire pressures as indicated on the GVW
Rating label for optimum tire life. See ªTiresº in the
Index for further details. Check tires for excessive or
abnormal wear or damage. Also check for damaged
wheels. Replace wheels and/or tires as needed.
(16) = Check spring
-to-axle U-bolts and shackle
bolts for proper torque. See the service manual for
torque sequence and specifications. When parts are
replaced, the torque must be checked and adjusted
more often during the first 6,000 miles (10 000 km).
Check torque at 500 miles (800 km) and 2,000 miles
(3 000 km) after first use of parts.
(17) = Check complete exhaust system and cab areas
near the exhaust system for broken, damaged, missing or
out
-of-position parts. Also inspect for open seams,
holes, loose connections or other conditions which could
let exhaust fumes seep into the driver compartment.
Needed repairs should be made at once. To help
maintain system integrity, replace exhaust pipes
whenever a new muffler is put on.
(18) = Check all gasoline engine drive belts for cracks,
fraying and wear. Replace as needed.(20) = With the engine off and below normal operating
temperature, check to see that the thermostatically
controlled engine cooling fan can be rotated by hand on
viscous
-operated drives. Replace as needed.
(21) = Check shields and underhood insulation for
damage or looseness. Adjust or replace as needed.
(23) = Wheel bearing service:

Grease type
-- Clean, inspect and lubricate with the
proper wheel bearing grease at designated intervals
or when hubs are removed. See ªRecommended
Fluids and Lubricantsº in the Index.

Oil
-filled type -- Some wheel bearings are lubricated
by rear axle lubricant. When you have oil
-filled
hubs, use lubricant identical to that used in your rear
axle. Lubricant change intervals are the same for
front and rear axles. However, you must maintain oil
level at the OIL LEVEL mark between change
intervals. See ªRecommended Fluids and
Lubricantsº in the Index.
(24) = Check the air intake system installation to see that
gaskets are seated properly and all hose connections,
fasteners and other components are tight. Tighten
connections and fasteners or replace parts as required.

7-19
(26) = Evaporative Control System Service
(if equipped): Check all fuel and vapor lines and hoses
for proper connections and correct routing (or every
24 months, whichever occurs first). Replace parts
as needed.
(28) = Replace spark plugs. Inspect wires for damage.
Check the wire boot and boot heat shield fit at spark
plugs and coil. Replace parts as needed.
(30) = Check the fuel tank, fuel cap and fuel lines for
damage which could cause leakage. Inspect fuel cap for
correct sealing ability and any indications of damage.
Check fuel cap gasket for even filler neck imprint.
Replace parts as needed.
(31) = Check EGR system as described in the
service manual. See ªService and Owner Publicationsº
in the Index.(32) = Inspect Electronic Vacuum Regulator Valve
(EVRV) filter for excessive contamination or plugging.
If needed, clean filter with solution of soap and water,
let dry and install.
(35) = Drain, flush and refill cooling system. See
ªRecommended Fluids and Lubricantsº in the Index for
what to use. Inspect hoses. Clean radiator, condenser,
pressure cap and neck. Pressure test cooling system and
pressure cap. For Caterpillar

diesel engines, always
refer to the Caterpillar Diesel Engine Operation &
Maintenance Manual for coolant recommendations and
change intervals.
(37) = Rear axle service: Change the lubricant. See
ªRecommended Fluids and Lubricantsº in the Index.
(38) = Front axle service: Re
-pack upper kingpin
roller bearing.

7-20
(39) = Air brake service:

Inspect brake lines and hoses for proper hook
-up,
binding, leaks, cracks, chafing, etc. Inspect drum
brake linings for wear or cracks. Inspect other brake
parts at each wheel, including drums, wheel
cylinders and piston heat shields, boots and wheel
speed sensor wiring. Check brake pedal for excessive
free play or travel (or every 6 months, whichever
occurs first) and have serviced if needed. Check
brakes more often if driving habits and conditions
result in frequent braking. Replace air dryer cartridge
only if excessive oil or moisture is present. A small
amount of oil in the system is normal and should not
be considered as a reason to replace the cartridge.

Test air lines for leaks; tighten as needed. Replace
compressor filter.

Inspect air parking brake chamber for leaks and
damage. Inspect lines and hoses for leaks, cracks,
chafing, etc. Also check all attachments for
tightness, wear or damage. Note: The spring brake
section of the rear brake diaphragms are
non
-serviceable.

Replace the air compressor filter element, mounted
on the air compressor. For remote air compressor
intake service, refer to engine air cleaner filter
replacement.
Remove, disassemble, clean and inspect the safety
valve, standard brake chamber, quick release valve,
quick release/double check valve combination,
parking brake control valve, double check valve,
pressure protection valve and alcohol injector.

Remove, disassemble and clean the application
valve; replace parts showing wear.

Remove, disassemble, clean and inspect the spring
brake control valve; replace rubber parts.
(40) = Clean and lubricate air brake automatic slack
adjuster. Check pushrod travel and auto adjustment
operation. Have serviced if needed.
(41) = Air brake chamber service: Check operation,
mounting, clamps and air lines and check for leaks.
(42) = Trailer brake hand control valve service: Check
operation; lubricate cam and follower.
(46) = Tighten the wheel stud nuts to the specified
torque values at 100 miles (160 km). Thereafter, tighten
them 1,000 miles (1 600 km) after each time the wheel
is removed. See ªTightening the Wheel Nutsº in
the Index.

7-21
Part B: Owner Checks and Services
Listed in this part are owner checks and services which
should be performed at the intervals specified to help
ensure the safety, dependability and emission control
performance of your vehicle.
For your safety and that of others, any of the
safety
-related components that may have been damaged
in an accident should be checked and any needed repairs
made before operating the vehicle.
At the minimum, these routine checks should be made
every 6 months or 6,000 miles (10 000 km), whichever
occurs first. Whenever repairs are needed, have them
completed before operating the vehicle.
At Each Fuel Fill
It is important for you or a service station attendant to
perform these underhood checks at each fuel fill.Engine Oil Level Check
Check the engine oil level and add the proper oil
if necessary. See ªEngine Oilº in the Index for
further details.
Engine Coolant Level Check
Check the engine coolant level and add DEX
-COOL

coolant mixture if necessary. See ªEngine Coolantº in
the Index for further details.
Windshield Washer Fluid Level Check
Check the windshield washer fluid level in the
windshield washer tank and add the proper fluid if
necessary. See ªWindshield Washer Fluidº in the Index
for further details.
Tire Inflation Check
Check tire inflation cold. Make sure tires are inflated to
the pressures specified on the GVW Rating label. See
ªLoading Your Vehicleº and ªTiresº in the Index for
further details.