manual transmission CHEVROLET C/K 2003 Owners Manual

2-
2-1
Section 2 Features and Controls
Here you can learn about the many standard and optional features on your vehicle, and information on starting,
shifting and braking. Also explained are the instrument panel and the warning systems that tell you if everything is
working properly
-- and what to do if you have a problem.
2
-2 Windows
2-5 Keys
2-7 Door Locks
2-8 Keyless Entry System (If Equipped)
2-12 Switchbanks
2-13 Theft
2-14 New Vehicle ªBreak-Inº
2-15 Ignition Positions
2-16 Starting Your Gasoline Engine
2-19 Starting the Diesel Engine
2-24 Starting Your DURAMAX
Diesel Engine
2-27 Engine Checks Before Operating
2-28 Engine Coolant Heater (If Equipped)
2-30 Diesel Engine Exhaust Brake (If Equipped)
2-31 Two-Speed Rear Axle Electric Shift Control
(If Equipped)
2
-34 Automatic Transmission Operation
2-36 Manual Transmission Operation
2-40 Parking
2-45 Parking Over Things That Burn
2-45 Engine Exhaust2
-46 Running Your Engine While You're Parked
(Automatic Transmission)
2
-47 Horn
2-48 Tilt Wheel (If Equipped)
2-48 Turn Signal/Multifunction Lever
2-55 Inter-Axle Differential Lock Control
(If Equipped)
2
-56 Rear Axle Differential Lock Control
(If Equipped)
2
-57 Exterior Lamps
2-60 Interior Lamps
2-61 Mirrors
2-63 Storage Compartments
2-65 Accessory Power Outlets
2-66 Trailer Connections (C4/C5 Models Only)
(If Equipped)
2
-67 Trailer Connections (C6/C7/C8 Models Only)
(If Equipped)
2
-68 The Instrument Panel-Your
Information System
2
-70 Instrument Panel Cluster
2-73 Warning Lights, Gages and Indicators

2-14
New Vehicle ªBreak-Inº
NOTICE:
Your vehicle doesn't need an elaborate
ªbreak
-in.º But it will perform better in the long
run if you follow these guidelines:

Let your engine warm up before you
operate your vehicle under load.

Keep your speed at 55 mph (88 km/h) or
less for the first 500 miles (805 km).

Don't drive at any one speed
-- fast or
slow
-- for the first 500 miles (805 km).
Don't make full
-throttle starts.
NOTICE: (Continued)
NOTICE: (Continued)

Avoid making hard stops for the first
200 miles (322 km) or so. During this time
your new brake linings aren't yet broken
in. Hard stops with new linings can mean
premature wear and earlier replacement.
Follow this breaking
-in guideline every
time you get new brake linings.

Use the lowest gear you can when you start
a loaded vehicle in motion and when going
up hills to avoid overloading the engine.

Check and adjust engine and transmission
fluid levels often and be sure tires are
properly inflated for the load you're
carrying.

If you have a Caterpillar
 diesel engine, see
the Caterpillar Diesel Engine Operation
& Maintenance Manual.

2-16 Engine Starter Over-Crank Protection
(If Equipped)
Your vehicle may have an engine starter over-crank
protection system. If the starter motor overheats and
shuts off due to over
-cranking, the motor must cool
down before it will reset and allow starter operation.
It can take up to six minutes before the starter will
work again.
Starting Your Gasoline Engine
Engines start differently. The 8th digit of your Vehicle
Identification Number (VIN) shows the code letter for
your engine. See ªVehicle Identification Numberº in
the Index. Follow the proper steps to start the engine.
To start a diesel engine, see ªStarting Your Diesel
Engineº in the Index.
Automatic Transmission
Set the parking brake and move your shift lever to
NEUTRAL (N) or PARK (P) if so equipped. Your
engine won't start in any other position
-- that's a
safety feature.
Manual Transmission
Set the parking brake, shift to neutral and hold the clutch
pedal to the floor while starting the engine.
Starter Motor Operation

The starter motor will disengage if you release
the key or the engine reaches a predetermined
engine speed.

To prevent overheating, the starter motor will
disengage after continuously operating for
15 seconds. You must release the key from the
start position to re
-engage the starter.

The starter motor will not engage if the engine is
already running.

The starter motor will disengage if, after
two seconds, the starter pinion gear does not
engage the flywheel or there is no engine rpm
signal from the engine speed sensor.

2-19
Starting the Diesel Engine
If you have a Caterpillar diesel engine, also refer to your
Caterpillar
Diesel Engine Operation & Maintenance
Manual for starting procedure.
For vehicles with the DURAMAX diesel engine, also
see ªStarting Your DURAMAX Diesel Engineº
following.
To make starting easier in cold weather (below 32F or
0C), the proper viscosity engine oil should be used.
See ªEngine Oilº in the Index. It's also best to heat the
engine oil first. You can do this by using an engine
coolant heater.
NOTICE:
If you ever need to have your vehicle towed, see
the part of this manual that tells how to do it
without damaging your vehicle. See ªTowing
Your Vehicleº in the Index.
Restarting the Diesel Engine While Moving
(Automatic Transmission)
If you have to restart the engine while the vehicle is
moving, you'll first have to shift the automatic
transmission to NEUTRAL (N). This safety feature
prevents starting the engine when the transmission is
in a drive gear.
Stopping the Diesel Engine
If you have a Caterpillar diesel engine, see your
Caterpillar
Diesel Engine Operation &
Maintenance Manual.
1. Set the parking brake and shift to NEUTRAL (N)
or PARK (P).
2. Turn the ignition key to OFF.
If your vehicle has a two
-speed axle, see ªRear Axle,
Tw o
-Speed Electric Shift Controlº or ªRear Axle,
Tw o
-Speed Airshift Controlº in the Index.

2-20 Cold Weather Starting
(Caterpillar

Diesel)
Because the diesel engine uses compression ignition, it
is harder to start in cold weather than a gasoline engine.
The air intake heater and use of the proper engine oil,
optional engine coolant heaters and optional ether
injection systems help cold weather starting. See the
Caterpillar

Diesel Engine Operation & Maintenance
Manual for more information.
NOTICE:
Your diesel engine has an electric air intake
heater system which reduces white smoke and
helps start the engine in cold weather. Do not
spray starting fluid into the air intake where it
can contact the heater elements.
If you don't have the GM Automatic Ether
Injection System, don't use starting fluid or you
could damage your engine. If you have the GM
system, use only GM approved starting fluid that
has been tested to establish compatibility with the
air inlet heater system.
Diesel Engine Warm-Up
Several factors affect how quickly your diesel engine
warms up. These can include outside temperature,
engine load, idle time and your vehicle's option content.
Your vehicle may be equipped with some features that
can help the engine reach operating temperature sooner.
Some of these features are discussed below.
Also, remember that an automatic transmission adds
heat to the cooling system through the heat exchanger in
the radiator. Because of this, vehicles equipped with
automatic transmissions are often able to retain engine
coolant heat better than manual transmission vehicles.
See your Caterpillar

Operation & Maintenance manual
for additional diesel engine warm
-up information.

2-21 Engine Alarm and Automatic Shutdown
(If Equipped)
Your check gages light will come on if the system senses
high engine temperature or low engine oil pressure. If high
engine temperature or low engine oil pressure is detected,
you will also hear a tone alarm at two beats per second.
The alarm and the light will remain on until the condition
is fixed. If the engine temperature or oil pressure condition
worsens, the tone alarm will go to five beats per second.
If the system senses low engine coolant, the five beat
per second alarm and the low coolant warning light will
come on.
The five beats per second tone alarm means that your
engine will shut down in approximately 25
-30 seconds.
There is also an engine shutdown light to indicate that
the engine will shut down. See ªAutomatic Engine
Shutdown Lightº later in this section.
Pull off the road and shut off the engine. Don't start it
until the reason for the problem is known, and the
problem is fixed. If the engine shuts down when you are
still in traffic, you can restart the engine and get another
25
-30 seconds of operation. Do this only if you have to,
since there is a problem that can harm the engine if it
isn't fixed. Engine automatic shutdown, for gasoline
engines, requires activation by your dealer.
High Idle System (Caterpillar
Diesel
and Gasoline Engines)
Your vehicle has both automatic and manual high idle
capabilities.
Automatic High Idle System (Diesel Engines)
(If Equipped)
The automatic high idle feature will engage whenever
you start your vehicle and the engine is below the preset
operating temperature. This will help decrease engine
warm
-up time.
Idle speed will then return to normal under any of the
following conditions:

The engine reaches the preset operating temperature
or has been operating for at least ten minutes.

The brake pedal is pressed.

The manual transmission clutch pedal is pressed or,
the automatic transmission (if equipped) is shifted
from NEUTRAL (N) or PARK (P).

The vehicle speed exceeds approximately
5 mph (8 km/h).

The throttle is pressed.

2-24
Starting Your DURAMAX

Diesel Engine
Your diesel engine starts differently than a
gasoline engine.
Automatic Transmission
Move your shift lever to PARK (P) or NEUTRAL (N).
Your engine won't start in any other position
-- that's
a safety feature. To restart when you're already moving,
use NEUTRAL (N) only.
NOTICE:
Don't try to shift to PARK (P) if your vehicle is
moving. If you do, you could damage the
transmission. Shift to PARK (P) only when your
vehicle is stopped.
Manual Transmission
Move your shift lever to neutral and hold the clutch
pedal to the floor while starting the engine. Your vehicle
won't start if the clutch pedal is not all the way
down
-- that's a safety feature.
Starting Your Engine
1. Turn your ignition key to RUN.
Observe the wait to start light. See ªWait To Start
Lightº in the Index. (This light may not come on
if the engine is hot.)
2. As soon as the wait to start light goes off,
IMMEDIATELY turn the ignition key to START.
When the engine starts, let go of the key.
NOTICE:
Holding your key in START for longer than
15 seconds at a time will cause your battery to be
drained much sooner. And the excessive heat can
damage your starter motor.

2-31
The accelerator and clutch pedals must be released in
order for the exhaust brake to engage. The exhaust brake
will not function when the cruise control feature is
active, and will automatically shut off when the
anti
-lock brake system is active.
CAUTION:
Be careful when using the exhaust brake or you
could lock the wheels and lose control of the
vehicle. Operators not familiar with an exhaust
brake should not use this brake on slippery
surfaces before learning to use it on dry surfaces.
If the vehicle's wheels begin to lock when using
the exhaust brake on slippery surfaces, switch the
exhaust brake off immediately. The exhaust
brake will turn off if the anti
-lock brake system
is activated.
Tw o-Speed Rear Axle Electric Shift
Control (If Equipped)
If your vehicle is equipped with this feature, you'll find
a label on the headliner above the windshield or in
another place near the driver that shows how to use it.
Be sure to follow the directions carefully.
Use the following directions based on the type of shift
control you have.
Manual Transmission
The rear axle shift control
switch for a manual
transmission is located
on the shift lever.
When the switch is up, the rear axle is in the high range.
Push the switch down to change to low range.

2-34 Rear Air Suspension Dump Control
If your vehicle is equipped with the Hendrickson HAS
Series single
-axle air suspension, you have this control.
The air suspension dump control allows the operator to
lower the deck height approximately 4.5 inches
(11.5 cm) from the normal frame height.
The switch to deflate and
inflate the air suspension is
located in the instrument
panel switchbank.
Press the bottom of the switch to deflate the air
suspension and lower the deck height. Press the top
of the switch to return the suspension to normal
deck height.
An indicator light will come on and stay on whenever
the switch is in the dumped position.
Automatic Transmission Operation
We build vehicles with five and six-speed automatic
transmissions. This part of the manual covers the basics
of these. With some of the transmissions, you will find
another manual in your vehicle that goes into more
detail. On the headliner, in front of and above the driver,
or in some other place near the driver, you will see a
label that describes important operating facts about the
automatic transmission in your vehicle. Make sure you
follow the instructions on this label.
Be sure to keep your parking brake set until you are
ready to shift into DRIVE (D), and press the brake pedal
while shifting from NEUTRAL (N) or PARK (P) to a
drive gear.
All vehicles equipped with automatic transmissions
can be started in PARK (P), if equipped, or in
NEUTRAL (N). See the Allison

Transmission
Operator's Manual in your vehicle for more information
about this.

2-36 Overdrive Defeat (If Equipped)
If your vehicle has this feature, you can select not to
shift up to fifth gear. This is useful when towing or
under a heavy load.
The overdrive defeat switch
is located in the instrument
panel to the right of the
steering column.
Press the switch to limit the transmission to fourth gear.
This will allow for better fuel economy and fewer
downshifts while pulling a tractor or trailer or under a
heavy load. The indicator light in the switch will come
on whenever overdrive defeat is active.
Manual Transmission Operation
Using the Clutch
When you're starting to move the vehicle, it's important
to begin with the engine speed at idle. Then start to
engage the clutch and listen for an engine speed drop
of about 100 rpm. At this point, the clutch is engaging,
so you should increase the engine speed and fully
engage the clutch. It's important not to increase the
engine speed sooner or before the clutch begins it's
engagement. If you do, you can cause damage to
your vehicle.
Double-Clutching
You must use the double-clutching method when you
shift an unsynchronized gear set. Disengage the clutch,
shift to neutral and engage the clutch. When upshifting,
slow the engine until the engine rpm and road speed
match. When downshifting, accelerate the engine until
the engine rpm and road speed match. Then quickly
disengage the clutch and move the shift lever to the next
gear position and engage the clutch.