service CHEVROLET CAMARO 1967 1.G Chassis Workshop Manual

CLUTCH AND TRANSMISSIONS 7-43

SPECIAL TOOLS

1.
J-1522 Pilot Bearing Driver
Fig.
3T - Clutch Special Tools

2.
J-5824 Clutch Pilot Tool
3. J-1448 Pilot Bearing Puller

CHEVROLET CHASSIS SERVICE MANUAL

CLUTCH AND TRANSMISSIONS 7-44

Fig.
4T - Manual Transmission Special Tools

1.
J-0933 Clutch Gear Bearing Retainer Wrench

2.
J-1126 Transmission Guide Pins

3. J-8059 Retainer Snap Ring Pliers

4.
J-21629 Countergear Loading Tool

5. J-22246 Countergear Loading Tool

6. J-5778 Extension Housing Bushing Remover

and Installer

7. J-5154 Extension Housing Seal Installer
8. J-5814-15

9. J-1453-01

J-358-1

10.
J-4653

11.
J-5590

12.
J-7785
Speedometer Drive Gear Remover

Speedometer Drive Gear Press Plates

Press Plate Holder

Overdrive Governor Wrench

Clutch Gear Bearing Installer

Clutch Gear Retainer Lip

Seal Installer

CHEVROLET CHASSIS SERVICE MANUAL

CLUTCH AND TRANSMISSIONS 7-45

23

Fig.
5T - Aluminum Powerglide Special Tools

1. J-9506

2.
J-3289-01

3.
J-9549

4.
J-21867

5.
J-4264

6. J-3387

7.
J-9539

8. J-6839

9. J-9546

10.
J-7782

11.
J-5133

12.
J-4599

13.
J-9542

14.
J-9557
Holding Fixture Adapters

Holding Fixture (Use with J-3289-20 Base)

Converter Safety Strap

Transmission Pressure Gauge and Hose

Oil Filler Tube and Funnel

Pilot Stud Set

Front Pump Puller Bolts (Use with weights

from Slide Hammers J-6585)

Front Pump Seal Driver

Clutch Drum Bushing Remover and Installer

Clutch Spring Compressor Adapter Plate

Clutch Spring Compressor

Planet Pinion Assembly Tool Set

Reverse Piston Spring Compressor

Transmission Case Rear Bushing Remover and

Installer and Rear Pump Bushing Remover
15.
J-7079

16.
J-6582

17.
J-9543

18.
J-5778

19.
J-5154

20.
J-5403

21.
J-5814

22.
J-5853

23.
J-8039

24.
J-21848

J-8001

J-5492

J-6585

J-6585-3

J-9534
Handle

Rear Pump Bushing Installer

Vacuum
Modu
lator Wrench

Extension Bushing Remover and Installer

Extension Oil Seal Installer

Snap Ring Pliers

Speedometer Drive Gear Remover and

Installer

Torque Wrench

Snap Ring Pliers

Low Band Adjusting Tool

Dial Indicator (Not Illustrated)

Dial Indicator Support Strap (Not Illustrated)

Slide Hammers (Not Illustrated)

Slide Hammer Adapters (Not Illustrated)

Bushing Remover (Not Illustrated)

CHEVROLET CHASSIS SERVICE MANUAL

CLUTCH AND TRANSMISSIONS 7-46

17 18 19 20 21 22

Fig.
6T - Turbo Hydra-Matic Special Tools

1.
J-6116-01

2.
J-8092

3. J-21359

4.
J-21364

5. J-2619

6. J-5154

7. J-6585

8. J-9539

9.
J-5590

10.
J-21867

11.
J-21370-6

12.
J-21370-5

13.
J-21795-1

14.
J-21795-2
Rear Unit Holding Fixture

Driver Handle

Pump Oil Seal Installer

Holding Fixture Adapter (Used with

J-6116-01 Fixture)

Slide Hammer (Used with 2619-4 Adapter and

Remover Tools J-21465-01)

Extension Oil Seal Installer

Slide Hammer Weights

Slide Hammer Bolts (3/8 - 16 Threads)

Speedo Gear Installer

Pressure Gauge and Hose

Rear Band Apply Fixture

Rear Band Apply Pin

Gear Unit Assembly Holding Tool

Part of Above Holding Tool
]5. J-5384

16.
J-21465-01

17.
J-21465-5

18.
J-21465-3

19.
J-21465-2

20.
J-21465-1

21.
J-21465-17

22.
J-21465-8

23.
J-21465-13

24.
J-2.1465-6

25.
J-21465-15

26.
J-21465-16

27.
J-21465-9

28.
J-21465-10

29.
J-22182
Converter Holding Strap

Bushing Tool Set

Part of Bushing Tool Set

Part of Bushing Tool Set

Part of Bushing Tool Set

Part of Bushing Tool Set

Part of Bushing Tool Set

Part of Bushing Tool Set

Part of Bushing Tool Set

Part of Bushing Tool Set

Part of Bushing Tool Set

Part of Bushing Tool Set

Part of Bushing Tool Set

Part of Bushing Tool Set

Extension Bushing Remover &

Installer (Not Illustrated)

CHEVROLET CHASSIS SERVICE MANUAL

CLUTCH AND TRANSMISSIONS 7-47

Fig.
7T - Turbo Hydro-Matic Special lools

1;
J-8763

2.
J-3289-14

3. J-21427-1

4.
J-9539

5. J-8105

6. J-21885

7. J-21369

8. J-21362
Transmission Holding Fixture

Holding Fixture Base

Speedo Gear Remover

Slide Hammer Bolts (3/8" - 16 Threads)

Speedo Gear Remover Puller

Accumulator Piston Installer

Converter Pressure Check Fixture

Seal Protector - Forward & Direct Clutch - Inner
9. J-21363

10.
J-21409

11.
J-21664

12.
J-4670

13.
J-8059

14.
J-5586

15.
J-5403

16.
J-1313
Seal Protector - Intermediate Clutch - Inner

Seal Protector - Forward Clutch - Outer

Clutch Spring Compressor Adapter Ring

Clutch Spring Compressor

Snap Ring Pliers

Snap Ring Pliers

Snap Ring Pliers

Torque Wrench 0-140 Ft. Lbs.

CHEVROLET CHASSIS SERVICE MANUAL

SECTION 8

FUEL TANK AND EXHAUST SYSTEMS

CONTENTS OF THIS SECTION

Page

Chevrolet .. . . 8-1

Fuel Tanks 8-1

Exhaust Systems 8-5

Chevelle 8-8

Fuel Tanks 8-8

Exhaust Systems 8-11

Chevy n ...... 8-13

Fuel Tanks 8-13
Page

Exhaust Systems 8-16

Corvette 8-18

Fuel Tanks 8-18

Exhaust Systems 8-24

Camaro 8-26

Fuel Tank 8-26

Exhaust System 8-30

Special Tools 8-33

CHEVROLET

FUEL TANKS

INDEX

Page

Page

General Description

Component Part Replacement

Fuel Tank
8-1 Fuel Lines 8-3

8-2 Fuel Tank Vent Lines 8-4

8-2 Metering Units (Gauge Sending Unit ) 8-4

GENERAL DESCRIPTION

All Sedan models (fig. 1) use a 24 gallon capacity

(approx.) fuel tank mounted between the frame rails

behind the rear axle. The fuel tanks are held in place

by two straps attached individually to the underbody at

each end. The strap? hinge at the forward end and secure

the tank at the rear with a nut and bolt. Anti-squeak

material is cemented to the tank at the strap locations.
A vent line from the forward-right side of tank extends

over a clip on the upper portion of wheelhouse.

The station wagon fuel tank has a 24 gallon capacity

(approx.). The tank is located at the back of the left rear

quarter wheelhouse area. The front of the tank is en-

closed with a protective shield (fig. 1).

VIEW A ^QUARTER PANEL

SEDAN

STATION WAGON
I

Fig.
1-Fuel
Tanks

CHEVROLET CHASSIS SERVICE MANUAL

FUEL TANK AND EXHAUST SYSTEMS 8-2

COMPONENT PART REPLACEMENT

FUEL TANK

Draining Tank

The absence of a drain plug in the gas tanks makes it

necessary to siphon fuel from the tank when draining is

needed. The following procedure is recommended.

1.
Obtain approximately 10 feet of 3/8" I.D. hose and

cut a flat-type slit 18" from one end. Make this cut

on the hose in the direction "toward the shorter end

(See Figure 2).

2.
Insert a small pipe nipple (slightly larger O.D. than

the hose I.D.) into the opposite end of hose.

3.
Insert the nipple end of the siphon hose into the fuel

tank filler neck with the natural curl of the hose

pointing down. Insert until the hose is heard to strike

bottom of the tank.

4.
With the opposite end of the hose in a suitable con-

taner insert an air hose in downward direction in the

flap-type slit and trigger the flow of fuel.
FUEL FLOW

-If*
APPROX.-1 >SUT «<>«
AS SHOWN

10 FEET APPROX.-

Fig. 2—Siphon Construction

FWD
V-8

VIEW B

Fig. 3-Fuel Lines

CHEVROLET CHASSIS SERVICE MANUAL

FUEL TANK AND EXHAUST SYSTEMS 8-3

CAUTION: Always drain gasoline from com-

plete fuel system including carburetor, fuel

pump and all fuel lines and fuel tank if the vehi-

cle is to be stored for any appreciable length of

time. This precaution will prevent accumulation

of gum formation and resultant poor engine

performance.

Removal and Installation (Except Station Wagon)

1.
Drain fuel tank.

2.
Raise vehicle.

3.
Disconnect fuel pickup line, ground wire.

4.
Disconnect meter wire at rear harness connector.

5. Disconnect vent pipe hose.

6. Remove tank support straps and lower tank carefully.

7. To install, reverse the removal procedure.
Removal and Installation (Station Wagon)

1.
Drain fuel tank.

2.
Raise vehicle.

3.
Remove gas tank shield at the back of the left rear

wheel; remove all screws including the screw

attachment at the bottom of the quarter panel.

4.
Disconnect fuel pickup line and gauge wires from

tank unit.

5. Remove ground wire attaching bolt at body location.

6. Remove strap assembly nut and carefully lower tank.

7. Reverse removal procedure to install.

FUEL LINES (Fig. 3)

The fuel lines extend from the fuel tank pickup to fuel

pump are routed on the underside of the right side of the

CAM

METER ASSY

GASKET

METER ASSY

ALL EXCEPT WAGONS

Fig.
4—Gauge Unit Assembly

CHEVROLET CHASSIS SERVICE MANUAL

FUEL TANK AND EXHAUST SYSTEMS 8-4

Fig.
5— Meter Assembly Removal Using Tool J-22554

vehicle. The fuel lines should be occasionally inspected

for leaks, kinks or dents. If evidence of dirt is found in

the carburetor or fuel pumto and disassembly, the lines

should be disconnected
and
blown out. Check the fuel tank

strainer for damage or omission. Note position of fuel

line clips for convertible models.
FUEL TANK VENT LINE

Sedan modei fuel tanks are vented to the atmosphere

at the top right- forward edge of. the tank. The vent line

is connected by a rubber hose with two clamps one at the

tank and the other at the vent pipe which is secured to

the underbody A rubber grommet around the vent pipe

acts as a seal to prevent gasoline fumes from entering

the.passenger compartment.

IMPORTANT: It is important to note that the

sedan gas tank cap is non-vented. It is neces-

sary to be assured that the vent line is free from

dirt, etc., and open at all times. If gasoline

fumes are detected, the rubber grommet should

be checked.

Station wagon models use a vented, anti-surge type gas

tank.

GAUGE UNIT AND FUEL STRAINER

Removal and Installation (Fig. 4)

1.
Follow tank removal procedure.

2.
Use Special Tool J-22554 (fig. 5) to remove cam

lock on sedan models and Tool J-8950 on station

wagons.

3.
Remove unit and rubber gasket.

4.
Reverse procedure to install.

CHEVROLET CHASSIS SERVICE MANUAL

FUEL TANK AND EXHAUST SYSTEMS 8-6

1"-1STGEAR

STD.
TRANS.

CONTACT OF EXHAUST

PIPE TO ENGINE PAN

RAIL IS PERMISSIBLE
VIEW E

Fig.
6—Single Exhaust Systems

CHEVROLET
CHASSIS SERVICE MANUAL