seat adjustment CHEVROLET CAMARO 2019 High Performance Owner Manual

Chevrolet Camaro High Performance Owner Manual Supplement (GMNA-
Localizing-U.S./Canada/Mexico-12461812) - 2019 - crc - 11/7/18
Driving and Operating 19
4. Using the hex feature on thetop of the mount, turn the top
mount 180° until the TRACK
CAMBER text is visible and the
second set of top mount holes
aligns with the strut tower
holes.
5. Reinstall the top mount bolts and torque to 29 Y
(21.4 lb ft).
6. Keep the top mount alignment pin and bolt for reinstallation
when the struts are returned to
the street position following the
track event.
7. Verify and adjust the vehicle alignment per track alignment
specifications to optimize
vehicle performance for the
track event.
8. Verify and re-adjust the vehicle alignment as needed following
the track event. Strut Spring Seat Adjustment
The front struts have a threaded
spring seat that allows adjustment
of the preload on the front springs.
The vehicle corner weights and front
trim heights can be adjusted.
The spring seat can be adjusted
approximately 10 mm (0.4 in) up or
down from the nominal position.
Each complete turn of the spring
perch will change the vehicle height
approximately 1.4 mm (0.06 in). Do
not allow the spring seat to contact
the black seal cap when adjusting in
the maximum upward direction.
To adjust the lower spring seat:
1. Raise the vehicle so the tires are completely off the ground.
2. Loosen the lower spring seatbolt. Do not completely remove
the bolt.
3. Turn the spring perch upward to increase spring preload,
or downward to decrease
spring preload.
4. Torque the spring seat bolt to 10Y (7.4 lb ft).
5. Verify and adjust the vehicle alignment as needed following
the spring seat adjustment.

Chevrolet Camaro High Performance Owner Manual Supplement (GMNA-
Localizing-U.S./Canada/Mexico-12461812) - 2019 - crc - 11/7/18
40 Vehicle Care
Towing the Vehicle
Caution
Incorrectly towing a disabled
vehicle may cause damage. The
damage would not be covered by
the vehicle warranty. Do not lash
or hook to suspension
components. Use the proper
straps around the tires to secure
the vehicle. Do not drag a locked
wheel/tire while loading the
vehicle. Do not use a sling type
lift to tow the vehicle. This could
damage the vehicle.
GM recommends a flatbed tow truck
to transport a disabled vehicle. Use
ramps to help reduce approach
angles, if necessary. A towed
vehicle should have its drive wheels
off the ground. Contact Roadside
Assistance or a professional towing
service if the disabled vehicle must
be towed. To tow the vehicle behind another
vehicle for recreational purposes,
such as behind a motor home, see
the owner
’s manual.SS 1LE, and ZL1 Only
Due to low ramp angles on ZL1 and
SS 1LE vehicles, use care when
loading the vehicle onto a flatbed
carrier. Front spring spacers are
provided for lifting the front
suspension if more clearance is
necessary when towing.
ZL1 1LE Only
Due to the high spring rate and
spring design used on ZL1 1LE
vehicles, spring spacers are not
provided. If more clearance is
needed when towing, raise the
adjustable spring seat to lift the front
suspension. See "Strut Spring Seat
Adjustment" in Track Events and
Competitive Driving 014.
Tow Eye Socket
The ZL1 vehicle is equipped with a
front tow eye that can be used to
pull the vehicle onto a flatbed car
carrier from a flat road surface. Do
not use the tow eye to pull the
vehicle from snow, mud, or sand.
The tow eye is in the rear
compartment storage area.
To install the tow eye:
1. Locate the tow eye socket through the opening in the
grille.
2. Install the tow eye into the socket by turning it clockwise
until it stops.