trunk CHEVROLET CAMARO SS 2010 User Guide
[x] Cancel search | Manufacturer: CHEVROLET, Model Year: 2010, Model line: CAMARO SS, Model: CHEVROLET CAMARO SS 2010Pages: 372, PDF Size: 1.91 MB
Page 224 of 372

Filling a Portable Fuel
Container
{WARNING
Never fill a portable fuel container
while it is in the vehicle. Static
electricity discharge from the
container can ignite the fuel vapor.
You can be badly burned and the
vehicle damaged if this occurs.
To help avoid injury to you and
others:
•Dispense fuel only into
approved containers.
•Do not fill a container while
it is inside a vehicle, in a
vehicle’s trunk, pickup bed,
or on any surface other than
the ground.
(Continued)
WARNING (Continued)
•Bring the fill nozzle in contact
with the inside of the fill
opening before operating the
nozzle. Contact should be
maintained until the filling is
complete.
•Do not smoke while
pumping fuel.
•Do not use a cellular phone
while pumping fuel.
Towing
General Towing
Information
Only use towing equipment that
has been designed for the vehicle.
Contact your dealer/retailer or towing
retailer for assistance with preparing
the vehicle for towing a trailer.
See the following trailer towing
information in this section:
•For information on driving while
towing a trailer, see Driving
Characteristics and Towing Tips.
•For maximum vehicle and trailer
weights, see Trailer Towing.
•For information on equipment
to tow a trailer, see Towing
Equipment.
For information on towing a disabled
vehicle, seeTowing the Vehicle
on page 9-87. For information on
towing the vehicle behind another
vehicle — such as a motorhome,
seeRecreational Vehicle Towing
on page 9-87.
8-48 Driving and Operating
Page 272 of 372

Fog Lamps
The base model vehicle may have
fog lamps which would be located
on the facia.
To replace one of these bulbs:
1. Locate the bulb assembly under
the front facia.
2. Disconnect the electrical
connector from the bulb
assembly and pull out the
bulb assembly.
3. Push in the new bulb assembly
to lock it into place.
4. Reconnect the electrical
connector to the bulb assembly.The up-level vehicle will not be
equipped with fog lamps.
Taillamps, Turn Signal,
and Stoplamps
To replace a taillamp, turn signal, or
stoplamp bulb:
1. Open the trunk. SeeTrunk on
page 1-8.
2. Remove the close out panel
retainers to gain access to
the bulb socket connectors.
3. Turn the bulb socket
counterclockwise to remove it.4. Pull the old bulb straight out of
the bulb socket.
5. Push the new bulb straight into
the bulb socket until it clicks.
6. Turn the bulb socket clockwise to
reinstall.
License Plate Lamp
To replace one of these bulbs:
1. Unclip the license plate lamp
from the facia opening.
2. Pull the license plate lamp down
through the facia opening.
9-40 Vehicle Care
Page 278 of 372

Fuses Usage
F10 Spare
F11 Spare
F12 Spare
F13 Display
F14OnStar
®Universal
Hands Free Phone
F15Body Control
Module 3
F16Body Control
Module 4
F17 Power Outlet 1
F18 Power Outlet 2
F19Steering Wheel
Controls Backlight
F20 Spare
F21 Spare
F22 Spare
F23 Trunk
F24Automatic Occupant
Sensing
Fuses Usage
F25Body Control
Module 1
F27Body Control
Module 8
F28 Spare
F29Body Control
Module 5
F30Body Control
Module 7
Circuit
BreakersUsage
CB7 Passenger Seat
CB26 Driver Seat
Relays Usage
K10Retained Accessory
Power
K605 Not Used
K609 Trunk
Rear Compartment
Fuse Block
The rear compartment fuse block is
located on the right side of the trunk
behind a cover. Remove the six
convenience net retainers, the rear
sill plate, and the two passenger side
trim retainers, then swing the trim out
of the way.
9-46 Vehicle Care
Page 309 of 372

Removal and Installation of
the Sealant Canister
To remove the sealant canister:
1. Remove the plastic cover.
2. Unscrew the connector (B) from
the canister (A).
3. Pull up on the canister (A) to
remove it.
4. Replace with a new canister
which is available from your
dealer/retailer.5. Push the new canister into place.
6. Screw the connector (B) to the
canister (A).
7. Slide the plastic cover back on.
Storing the Tire Sealant
and Compressor Kit
This vehicle may have a tire sealant
and compressor kit in place of a jack
or spare tire. It is located in a foam
container in the trunk.
Tire Changing
Removing the Spare Tire
and Tools
Spare Tire
1. Open the trunk. SeeTrunk on
page 1-8.
2. Remove the carpet.
3. Turn the center retainer
counterclockwise to remove
the spare tire cover.
4. Remove the spare tire and place
it next to the tire being changed.
Vehicle Care 9-77
Page 314 of 372

12. Lower the vehicle by turning the
jack handle counterclockwise.
Lower the jack completely.
13. Tighten the wheel nuts firmly in
a crisscross sequence, as
shown.{WARNING
Wheel nuts that are improperly or
incorrectly tightened can cause
the wheels to become loose or
come off. The wheel nuts should
be tightened with a torque wrench
to the proper torque specification
after replacing. Follow the torque
specification supplied by the
aftermarket manufacturer when
using accessory locking wheel
nuts. SeeCapacities and
Speci cations on page 11-2for
original equipment wheel nut
torque specifications.
Notice:Improperly tightened
wheel nuts can lead to brake
pulsation and rotor damage.
To avoid expensive brake repairs,
evenly tighten the wheel nuts
in the proper sequence and to
the proper torque speci cation.
SeeCapacities and Specifications
on page 11-2for the wheel nut
torque speci cation.
Storing a Flat or Spare Tire
and Tools
{WARNING
Storing a jack, a tire, or other
equipment in the passenger
compartment of the vehicle could
cause injury. In a sudden stop or
collision, loose equipment could
strike someone. Store all these
in the proper place.
To store a flat or spare tire
and tools:
1. Replace the jack and tools.
2. Replace the spare tire cover.
3. Turn the retainer nut clockwise to
tighten.
4. Replace the rear trunk carpet.
5. Place the flat tire face up on the
load floor.
9-82 Vehicle Care