tire type CHEVROLET CORVETTE 1993 4.G Owners Manual
[x] Cancel search | Manufacturer: CHEVROLET, Model Year: 1993, Model line: CORVETTE, Model: CHEVROLET CORVETTE 1993 4.GPages: 370, PDF Size: 21.43 MB
Page 285 of 370
Downloaded from www.Manualslib.com manuals search engine Sewice & Appearance Care
When It’s Time.for New Tires
One way to tell when it’s time for new
tires is to check the treadwear indicators,
which will appear when your tires have
only%2 inch (1.6 mm) or less of tread
remaining.
You need a new tire if:
* You can see the indicators at three
You can see cord or fabric showing
The tread or sidewall is cracked, cut
places around the tire.
through the
tire’s rubber.
or snagggd deep enough to show cord
or fabric.
The tire has a bump, bulge or split.
The tire has a puncture, cut or other
damage that can’t he repaired well
because
of the size or location of the
damage.
Buying New Tires
To find out what kind and size of tires
you need, look at the Tire-Loading
Information label. The
tires installed on
your vehicle when it was new had a Tire
Per€omance
Criteria Specification
(TPC Spec) number on each tire’s
sidewall. When
you get new tires, get
ones with that sme TPC Spec number.
That way, your vehicle will continue to
have
tires that are designed to give
proper endurance, handling, speed
rating, traction, ride and other things
during normal service on your vehicle.
If your tires have an all-season tread
design, the TPC Spec number will be
followed by an “MS” (for mud and
snow).
. ... r .: ;.- - .
If yuu ever replace your tires with those
,not having a TPC Spec number, make
SLUT they are the same size, load range,
speed rating and construction
type
(bias, bias-belted or radial) as your
original tires.
G
Page 287 of 370
Downloaded from www.Manualslib.com manuals search engine ...
Service & Appearance Care
Tra~ti~n-A, 6, C
33% traction grades, from highest to
.lowest are:
A, B, and C. They represent
the tire's ability to stop
on wet pavement
as measured under controlled conditions
on specified ,government test surfaces
of
asphalt and concrete. A tire marked C
may have podr.traction p-erformance.
Warning: The traction grade assigned
to.
this tire is based on braking (straight-
ahead) traction
tests and does not
include cornering (turning) traction.
186.
Temperature-A, B, C
The temperature grades are A (the
highest),
B, and'C, representing the
tire's-resistance to the generation of
heat and its ability to dissipate heat
when tested under controlled conditions
on a specified indoor laboratory test
wheel: Sustained high temperature can
cause the inaterid af the tire to
degenwate.-and
reduce tire @e, and
excessive temperature can
lead to.
sudden tire failure. The-grade
C
corresponds to. a level of performance
which
dl passenger car tires must meet
under:the Federal
Motor Vehicle Sa€ety
Standard
NO.. 109. Grades B.and A
represent higher levels of perfomnance on
the laboratory test wheel than the
minimum
required by law.
Warning: The temperatute grade for
this tire 'is established for a tire that is
properly inftated and not overloaded.
Excessive
speed, underinflation, or
excessive loading, iither separately or in
combination, cah cause heat buildup
and possible
tire failure.
Those grades are
molded on the
sidewalls of passenger car tires.
While the tires available
as standard or
optional equipment on General
Motors
vehicles may vary with. respect to these
grades, all such
tires meet Gene$d.
Motors performance
standards and
have
been appToved for use QII General
Motors vehicles. All passenger type
(P
Metric) tifes .must conform to federal
safety requirements in addition to these.
grades.
Page 291 of 370
Downloaded from www.Manualslib.com manuals search engine Service & Appearance Care
= = 290
Cleaning the Inside of Your
Coweqe
Use a 'vacuum cleaner often to get rid df
dust and loose dirt. Wipe vinyl with a
clean, damp cloth.
Your Chevralet ,deder has two GM
cleaners-a solvent-type spot lifter and
a foam-type powdered cleaner. They
will clean normal spots and stains very
well.
Here
are some cleaning tips:
Always read the instructions on the
9 Clean up stains as soon as you can-
cleaner label.
before
they set.
9 Use a clean cloth or sponge, and
change to a clean area ,aften.. A so&
brush may be used if stains are
stubborn.
ventilated area only. If you use them,
don't saturate the stained area.
If a ring forms after spot cleaning,
clean the entire area immediately or it
will set.
Use solvent-type cleaners in a well-
. .. ' ;I I.. . . ..
Using Foam-Type Cleaner on
Fabric.
9 Vacuumand brush the; area to .remove.
9 Always clean a whole trim panel or
any loose
dirt.
section. Mask surrounding trim along
stitch or welt lines.
Mix Multi-Purpose Powdered Cleaner
following the directions on the
container label.
* Use suds only and apply with a clean
9 Don't saturate the material.
Don't rub it roughly.
As soon as you've cleaned the secnon,
sponge.
use a sponge to remove the suds.
w
Page 295 of 370
Downloaded from www.Manualslib.com manuals search engine Service & Appearance Care
Cleaning the Top of the
lnstrumenf Panel
Use only mild soap and water to dean
the
tap surfaces of the. instrument.
panel. Sprays containing Silicones
or
waxes may cause annoying reflections
in the windshield and even make it
dK1cult to see through the.windshield
under certain conditions.
Cleaning Speaker Covers
Vacuum around. a Delco-BoseB- speaker
cover gently,
so that the- sp.ealref won’t
be damaged. If something gets on one of
them, follow the step earlier under
Using -Sslvsnt-Type Cleaner on Fabric.
Uscas little solvent as you can.
C/eaning “Dulso”-Coated
Molding
Your Corvette’s inside rear window
(hatch area) molding is “Dulso” coated.
For lightly soiled molding, wipe with a
sponge OF a soft lint-free cloth that
has been dampened with water.
+ For heavily soiled molding, use warm
soapy water.
You can recondition molding.showing
‘marks
or- scratches by briskIy wiping
the
area with GM Fabric Cleaner
(solvent type). Don’t
use too much
.cleaner.
If a- ring forms, immediately
repeat the cleaning procedure over
a
slightly larggr area, “feathering”
toward
the center of the ring. If-the
ring
still remains, wipe the entire
molding.