manual radio set CHEVROLET TRACKER 1995 Owners Manual

AM/FM Stereo
To Play the Radio
Turn the ONNOL knob to turn the system on or off.
VOL: Turn this knob to adjust the volume.
Finding a Station
AM-FM:
Press this button to get AM or FM. The
lighted display shows your selection.
TUNE: Press TUNE or TUNE 4 to go to a higher or
lower station. Press and hold
to continue tuning and
release when
you find your station. The display will
show the frequency
of each station tuned.
SEEK: Press SEEK or SEEK 4 and the radio will
tune
to the next higher or lower station and stay there.
PUSHBUTTONS: The six pushbuttons let you return to
your favorite stations. To
set the pushbuttons for up to
12 stations (6 AM and 6 FM), tune in the station. Then,
press and hold one
of the pushbuttons for at least two
seconds. The sound
will go away for a second and will
return when the station
is stored.
Repeat these steps for each pushbutton.
ProCarManuals.com

Setting the Tone TREB:
Turn this knob to the right to hear more treble.
BASS: Turn this control behind the TREB knob to the
right to hear more bass.
Adjusting the Speakers
FADE: Turn this knob to move the sound between the
front and rear speakers.
BAL: Turn this control behind the FADE knob to move
the sound between the left and right speakers.
Recall
AM/FM Stereo with Cassette Tape Player
RCL: Press this button to see the station being played
for a moment. Or, press it if you want to
see the time
when the ignition is
off.
To Play the Radio
Turn the ON/VOL knob to turn the system on or off.
VOL: Turn this knob to adjust the volume.
ProCarManuals.com

Finding a Station
AM-FM: Press this button to get AM, FM1 or FM2.
The lighted display shows your selection.
TUNE: Press TUNE or TUNE 4 to go to a higher or
lower station. Press and hold to continue tuning and
release when you find your station. The display will
show the frequency of each station tuned.
SEEK: Press SEEK or SEEK 4 and the radio will
tune to the next higher or lower station and stay there.
PUSHBUTTONS: The six pushbuttons let you return to
your favorite stations. To set the pushbuttons for up to
18 stations (6 AM, 6 FMl and 6 FM2), tune in the
station. Then press and hold one
of the pushbuttons for
at least two seconds. The sound will go away for a
second and will return when the station is stored.
Repeat these steps for each pushbutton.
PSCAN: Press this button to hear each of your preset
stations for a few seconds. When you want to stop at a
chosen station, press PSCAN again.
Setting the Tone
TREB: Turn this knob to the right to hear more treble.
BASS: Turn this control behind the TREB knob to the
right to hear more
bass.
Treble and bass cannot be adjusted manually when
TONE SELECT is on.
TONE SELECT Press this button to choose preset
treble and bass equalization settings designed for
ROCK, NEWS, POP, JAZZ and CLASSICAL.
ROCK will appear when you first press TONE SELECT.
Each time you press it, another setting will appear on the
display. If
you press it one more time after CLASSICAL
appears on the display, tone control will be back to the
treble and bass knob.
Adjusting the Speakers
FADE:
Turn this knob to move the sound between the
front and rear speakers.
BAL: Turn this control behind the FADE knob to move
the sound between the right and left speakers.
Recall
RCL: Press this button to see the station being played
for a moment. Or, press
it if vou want to see 2 time
when the ignition is off.
ProCarManuals.com

To Play a Cassette Tape
Your tape player is built to work best with tapes that are
30 to 45 minutes long on each side. Tapes longer than
that are
so thin they may not work well in this player.
The longer
side with the tape visible should face to the
right. If you hear nothing or hear just a garbled sound,
it
may not be in squarely. Press HA to remove the tape and
start over.
Once the tape is playing, use the knobs for volume, fade
and balance, just as you do
for the radio. The lighted
arrows show which side
of the tape is playing.
MTL: Your bias is set automatically. MTL will appear
on your display when a metal or chrome tape
is inserted.
FF: Press this button to advance rapidly to another part
of the tape. Press FF, RCLPROG or mA to return to
playing speed.
REW: Press this button to reverse the tape rapidly. Press
REW or RCL/PROG to return to playing speed. If you
press RCL/PROG, the tape
will also change sides.
NEXT Press this button to go forward to the beginning
of the next selection. Press the button again or press
RCLRROG or
mA to cancel this function. For
NEXT to
work properly, your tape must have at
least three
or four seconds of silence between each
selection. If you press RCL/PROG, the tape will also
change sides.
PREV: Press this button to go back to the beginning
of the last selection. Press PREV again or press
RCLPROG or WA to cancel this function.
RCLRROG: Press this button to switch from one side
of the tape to the other. Your cassette tape player can
play continuously because the player has an
auto-reverse feature.
NOISE REDUCTION: Press On@ to remove noise
from Dolby@
B NR-encoded tapes.
Dolby@
B Noise Reduction is manufactured under
license from Dolby Laboratories Licensing Corporation.
Dolby@ and the
c]o@ symbol are trademarks of Dolby
Laboratories Licensing Corporation.
WA: Press the button with this symbol to remove the
tape and switch to radio.
RADIO MNTR: Press this button to hear the radio
when you are fast forwarding or reversing a cassette
tape.
You can use the TUNE, SEEK and PSCAN buttons
while in the radio monitor mode.
ProCarManuals.com

Cln: This message may appear on the display. If it does,
your cassette tape player needs to
be cleaned. It will still
play tapes, but you should clean it as soon as possible to
prevent damage to your tapes and player. See “Care of
Your Cassette Tape Player” in the Index. After you clean
the player, press and hold EJECT for
five seconds to
reset the Cln indicator. “---” will appear in the display to
show the indicator was reset.
Theft-Deterrent Feature
The theft-deterrent feature for the A” stereo with
cassette tape player can be used
or ignored. If ignored, the
system plays normally. If it is used, your system won’t be \
usable
if it’s ever stolen because it will go into LOC mode
anytime your vehicle loses battery power. The unlock code must be entered or the radio will not
turn on.
Setting Your Security Code
The following instructions will tell you how to enter a
security code
into the system. If your vehicle loses
battery power for any reason, you must enter the
security code again before the system will turn
on.
You are now ready to enter your security code. Don’t
wait more
than 15 seconds between steps.
Press
4 SEEK b or 4 TUNE and “0000” will appear
on the display.
Press SEEK
4 and hold it until the first digit of your
code appears. Release the button.
Press
SEEK b and hold it until the second digit of your
code appears. Release
the button.
Press
TUNE 4 and hold it until the third digit of your
code appears. Release the button.
Press
TUNE b and hold it until the fourth digit of your
code appears. Release the button.
Press
AM-FM after you have checked that the code you
entered
is the one you wrote down. “rEP’ will appear on
the display, which means you need to repeat steps 5
through 9.
Press AM-FM again and the display will now show
SEC.
Write down any four-digit number and keep it in a safe place.
Then turn the ignition switch to the ACC or ON position
and the audio system
off. Press the 1 and 4 buttons together.
Hold them down until
“----” shows on the display.
3-10
ProCarManuals.com

AM/FM Stereo with Cassette Tape and
Compact
Disc Players
To Play the Radio
Turn the ONNOL knob to turn the system on or off.
VOL: Turn the ONNOL knob to adjust the volume.
Finding a Station
AM-FM: Press AM-FM to get AM, FM 1 or FM2. The
lighted display shows your selection.
TUNE: Press TUNE b or TUNE 4 to go to a higher or
lower station. Release when
you find your station. The
display will show the frequency of each station tuned.
SEEK: Press SEEK b or SEEK 4 and the radio will
tune to the next higher or lower station and stay there.
PUSHBUTTONS: The six pushbuttons let you return to
your favorite stations. To set the pushbuttons for up to
18 stations (6 AM, 6 FM 1 and 6 FM2), tune in the
station. Then, press and hold one
of the pushbuttons for
at least two seconds.
The sound will go away for a
second and will return when the station is stored.
Repeat these steps for each pushbutton.
PSCAN: Press this button to hear each of your preset
stations for a few seconds. When you want to stop at a
chosen station, press PSCAN again.
ProCarManuals.com

Setting the Tone To Play a Cassette Tape
Your tape player is built to work best with tapes that are
30 to 45 minutes long on each side. Tapes longer than
that are
so thin they may not work well in this player.
The longer side with the tape visible should face to the
right.
If you hear nothing or hear just a garbled sound, it
may not be in squarely. Press STOP or EJECT to
remove the tape
and start over.
TREB: Turn this knob to the right to hear more treble.
BASS: Turn this control behind the TREB knob to the
right
to hear more bass.
TONE SELECT Press this button to choose preset
treble and bass equalization settings designed for
ROCK, NEWS, POP, JAZZ and CLASSICAL.
ROCK will appear when you first press TONE SELECT.
Each time you press it, another setting will appear on the
display. If you press it one more
time after CLASSICAL
appears on
the display, tone control will be back to the
treble and bass
knob.
Adjusting the Speakers
FADE:
Turn this knob to move the sound between the
front and rear speakers.
BAL: Turn this control behind the FADE knob to move
the sound between the right and
left speakers.
Recall
RCL: Press RCL v A to see the station being played
for
a moment. Or, press it if you want to see the time
when the ignition is off. Once
the tape is playing,
use the knobs for volume, fade
and balance, just as you do for the radio. The lighted
arrows
show which side of the tape is playing.
MTL: Your bias is set automatically. MTL will appear
on the display
when a metal or chrome tape is inserted.
FF: Press this button to advance rapidly to another part
of the tape. Press
FF, RCL v A or STOP to return to
playing speed.
If you press RCL 7 A, the tape will also
change sides.
REW. Press this button to reverse the tape rapidly. Press
REW, RCL
v A or STOP to return to playing speed. If
you press RCL
A, the tape will also change sides.
NXT Press this button to go forward to the beginning of
the next selection. Press NXT again or press RCL v A
or STOP to cancel this function. If you press RCL v A,
the tape will also change sides.
8 3-13
- ~ ProCarManuals.com

PRV Press this button to go back to the beginning
of the last selection. Press the button again or press
RCL
A or STOP to cancel this function.
For NXT and PRV to work properly, your tape must
have at least three or four seconds
of silence between
each selection. If you press RCL
A, the tape will also
change sides.
RPT Press this button to go to the beginning of the
selection and play it again. Press RPT again to cancel
this function.
NOISE REDUCTION: Press OU@ to remove noise
from Dolby@
B NR-encoded tapes.
Dolby@
B Noise Reduction is manufactured under
license from Dolby Laboratories Licensing Corporation.
Dolby@ and the
DO@ symbol are trademarks of Dolby
Laboratories Licensing Corporation.
RDM: When playing a tape, press this button during FF
or REW to hear the radio. Press it again to turn the radio
off. During this operation, only TUNE, SEEK and
PSCAN will
work.
TAPE SIDES: Press RCL v A to switch from one side
of the tape to the other.
STOP: Press this button to stop the tape and switch to
radio.
EJECT Press this button to remove the tape and switch
to radio.
Cln: This message may appear on the display. If it does,
your cassette tape player needs to be cleaned. It
will still
play tapes, but you should clean it
as soon as possible to
prevent damage to your tapes and player. See “Care of
Your Cassette Tape Player”
in the Index. After you clean
the player, press and hold EJECT for five seconds to
reset the Cln indicator.
“---” will appear in the display to
show the indicator was reset.
To Play a Compact Disc
Don’t use the mini-discs (three-inch singles). They
won’t eject. Use full-size compact discs.
Insert your disc into the CD slot on your audio system.
If the disc comes back out, it could be that the road is
rough, (the disc should
play when the road is smoother);
the disc is upside down; dirty, scratched or wet; or there
is too much moisture
in the air. (If there’s too much
moisture
in the air, wait about one hour and try again.)
If you see
Err on the display, the disc player is too hot to
play the disc. Press
RCL 7 A to take Err off the display.
ProCarManuals.com

Track Number and Playing Time: Press RCL A to
see which track is playing. Press
it again within five
seconds to see how long
it has been playing.
The track number
also appears when the disc is inserted
or you change the volume.
PRV: Press this button to hear a track again. If you hold
this button or press
it more than once, the disc will
return to previous tracks.
NXT Press this button to hear the next track now
(instead of waiting
until the present track is finished).
If you hold this button, or press
it more than once, the
disc will advance further.
REW Press and hold this button to return rapidly to a
favorite passage. Release it to play the passage.
FF: Press and hold this button to fast forward or
advance quickly within a track. Release
it to resume
playing.
COMP: Press this button to make soft and loud
passages more nearly equal in volume.
RPT Press this button once to hear a selection over
again.
RDM: Pressing this button will cause the CD player to
play the tracks back
in random order. To cancel the
random feature, press RDM or RPT.
STOP: Press this button or AM-FM to stop playing the
disc and switch to radio. Press STOP again to restart the
disc
at the point where it stopped.
CD-TP: Press this button to switch between playing a
tape and a CD when both are inserted.
EJECT: Press this button to eject the disc and the radio
will play. The disc will start playing at track 1 when you
reinsert
it.
Theft-Deterrent Feature
The theft-deterrent feature for the AM/FM stereo with
cassette tape and compact disc player can be used or
ignored.
If ignored, the system plays normally. If it is
used, your system won't be usable
if it's ever stolen
because
LOC will appear on the display when battery
power
is lost.
Setting Your Security Code
The following instructions will tell you how to enter a
security code into the system. If your vehicle loses
battery power for any reason, you must enter the
security code again before the system will
turn on.
ProCarManuals.com

Tips about Your Audio System
Hearing damage from loud noise is almost undetectable
until it is
too late. Your hearing can adapt to higher
volumes
of sound. Sound that seems normal can be loud
and harmful to your hearing. Take precautions by
adjusting the volume control
on your radio to a safe
sound level before your hearing adapts
to it.
To help avoid hearing loss or damage:
Adjust the volume control to the lowest setting.
Increase volume slowly until you hear comfortably
and clearly.
NOTICE:
Before you add any sound equipment to your
vehicle
-- like a tape player, CB radio, mobile
telephone or two-way radio
-- be sure you can
add what you want.
If you can, it’s very
important to do it properly. Added sound
equipment may interfere with the operation
of
your vehicle’s engine, Delco’ radio or other
systems, and even damage them. And, your
vehicle’s systems may interfere with the
operation of sound equipment that has been
added improperly.
So, before adding sound equipment, check with
your dealer and be sure to check Federal rules
covering mobile radio and telephone units.
ProCarManuals.com