engine CHEVROLET TRACKER 1998 1.G Owners Manual

Downloaded from www.Manualslib.com manuals search engine 3. Fill the radiator with the proper coolant mixture, up
to the base of the filler neck. (See “Engine Coolant” in the Index for more information about the proper
coolant mixture.)
4. Then fill the coolant recovery tank to the
FULL mark.
5. Put the cap back on the coolant recovery tank, but
leave the radiator pressure cap off.
6. Start the engine and let it run until you can feel the
upper radiator hose getting hot. Watch out for the
engine cooling fan.
7. By this time, the coolant level inside the radiator
filler neck may be lower. If the level is lower, add
more of the proper coolant mixture through the
filler neck until the level reaches the base
of the
filler neck.
5-20

Downloaded from www.Manualslib.com manuals search engine If a Tire Goes Flat
8. Then replace the pressure cap. At any time during
this procedure if coolant begins to flow out of the
filler neck, reinstall the pressure cap. Be sure the
arrows on the pressure cap line up like this. It’s unusual
for a tire to “blow out” while you’re driving,
especially if you maintain your tires properly. If air goes
out of a tire, it’s much more likely to leak out slowly.
But if you should ever have a “blowout,” here are a few\

tips about what to expect and what to do:
If a front tire fails, the flat tire will create a drag that
pulls the vehicle toward that side. Take your foot off the
accelerator pedal and grip the steering wheel firmly.
Steer to maintain lane position, and then gently brake to
a stop well out
of the traffic lane.
A rear blowout, particularly on a curve, acts much like a
skid and may require the same correction you’d use in a
skid. In any rear blowout, remove your foot from the
accelerator pedal. Get the vehicle under control by
steering the way you want the vehicle to go. It may be
very bumpy and noisy, but you can still steer. Gently
brake to a stop
-- well off the road if possible.
If a tire goes flat, the next part shows how to
use your
jacking equipment
to change a flat tire safely.

Downloaded from www.Manualslib.com manuals search engine Changing a Flat Tire
If a tire goes flat, avoid further tire and wheel damage
by driving slowly to a level place. Turn on your hazard
warning flashers.
A CAUTION:
Changing a tire can cause an injury. The vehicle
can slip
off the jack and roll over you or other
people.
You and they could be badly injured.
Find
a level place to change your tire. To help
prevent the vehicle from moving:
1. Set the parking brake firmly.
2. Put an automatic transmission shift lever in
PARK
(P) or shift a manual transmission to
FIRST
(1) or REVERSE (R).
3. If you have a four-wheel-drive vehicle,
be sure the transfer case
is in a drive
gear
-- not in NEUTRAL (N).
4. 'hrn off the engine.
To be even more certain the vehicle won't move,
you can put blocks at the front and rear
of the
tire farthest
away from the one being changed.
CAUTION: (Continued) That
would be the tire
on the other side of the
vehicle,
at the opposite end.
The following steps will tell
you how to use the jack and
change a tire.

Downloaded from www.Manualslib.com manuals search engine Removing the Spare Tire and Tools
The jack handle is under the driver’s seat.
The jack and wheel wrench are under the front
passenger’s seat.
5-23

Downloaded from www.Manualslib.com manuals search engine The tools you'll be using include the jack (A), jack
handle
(B) and wheel wrench (C).
The spare tire is mounted on your tailgate. Pull the cover
off of the spare tire.
Attach the jack handle to the jack.
Turn the jack handle
to the right to raise the lift head.
5-24

Downloaded from www.Manualslib.com manuals search engine Insert your key into the wheel lock on the spare tire and
pull the wheel lock
off.
Kemove wheel nuts with the wheel wrench.
Remove the spare tire from the mounting bracket and
place it near your flat tire.
Attach the jack handle to the jack bolt.
Turn the jack
handle to the right to raise the lift head.
5-25

Downloaded from www.Manualslib.com manuals search engine Removing the Flat Tire and Installing the Spare Tire
1. Using the wheel wrench, loosen all the wheel nuts.
Don't remove them yet.
2. Position the jack and raise the jack lift head until it
fits firmly onto the notches nearest to the flat tire.
(Under the vehicle near each wheel, there are
notches in the vehicle's rocker flange.)
5-26

Downloaded from www.Manualslib.com manuals search engine A CAUTION:
Getting under a vehicle when it is jacked up is
dangerous.
If the vehicle slips off the jack, you
could be badly injured or killed. Never get under
a vehicle when
it is supported only by a jack.
-
A CAUTION:
Raising your vehicle with the jack improperly
positioned can damage the vehicle and even
make the vehicle fall.
To help avoid personal
injury and vehicle damage, be sure to fit the jack
lift head into the proper location before raising
the vehicle.
3. Raise the vehicle by turning the jack handle to the
right. Raise the vehicle
far enough off the ground so
there is enough room for the spare tire to fit.
5-27

Downloaded from www.Manualslib.com manuals search engine 4. Remove all the wheel
nuts and take
off the
flat
tire.
Remove any rust or dirt
from the wheel bolts,
mounting surfaces and
spare wheel. Rust
or dirt on the wheel, or on me parts to
which
it is fastened, can make the wheel nuts
become loose after
a time. The wheel could come
off and cause an accident. When you change
a
wheel, remove any rust or dirt from the places
where the wheel attaches to the vehicle. In an
emergency, you can use
a cloth or a paper towel
to do this; but be sure to use
a scraper or wire
brush later, if you need to, to get all the rust or
dirt
off.
--.
6. Place the spare on the wheel mounting surface.
5-28

Downloaded from www.Manualslib.com manuals search engine A CAUTION:
Never use oil or grease on studs or nuts. If you
do, the nuts might come loose. Your wheel could
fall off, causing a serious accident.
7. Replace the wheel nuts
with the rounded end
of the nuts toward the
wheel. Tighten each nut
by hand until the wheel is held against the hub.
8. Lower the vehicle by turning the jack handle to the
left. Lower the jack completely.