light CHEVROLET TRACKER 2000 2.G User Guide

2-19 Overdrive Off Switch (If Equipped)
The overdrive off switch is located on the left side of the
shift lever. By operating the overdrive off switch, the
four
-speed automatic transmission (three-speed plus
overdrive) can be converted to a three
-speed automatic
transmission. While in the three
-speed mode, the
transmission will not shift into the overdrive position.To convert the transmission to the three
-speed
mode, push in the overdrive off switch and release it.
The switch will come out and the OD/OFF indicator
light on the instrument panel cluster will come on. The
Overdrive Off switch is for normal driving, however, it
also offers more power and lower fuel economy than
driving in the overdrive position. Here are some times
you might choose to drive with the overdrive off
switch engaged:

When driving on hilly, winding roads.

When going down a steep hill.
To return the transmission to the four
-speed mode,
push in the overdrive off switch again. The switch will
remain in and the OD/OFF indicator light will go off.
Disengaging the Overdrive Off switch is for normal
driving with the four
-speed automatic transaxle.
If you need more power for passing, and you're:

Going less than about 35 mph (55 km/h), push
your accelerator pedal about halfway down.

Going about 35 mph (55 km/h), push your
accelerator all the way down.
Please note that if the transfer case shift lever is in the
4L position, the four
-speed automatic transmission will
remain in the three
-speed mode.

2-20 Power Mode Selector Switch
A power mode selector
switch is included
with the four
-speed
automatic transmission.
When you need more power for climbing hills or
quicker acceleration, press the P (power) switch. The
POWER indicator light on the instrument panel cluster
will come on. For normal driving, press the N (normal)
switch. The POWER indicator light will go off.
Manual Transmission Operation
5-Speed
This is your shift pattern.
Here's how to operate
your transmission:
FIRST (1): Press the clutch pedal and shift into
FIRST (1). Then, slowly let up on the clutch pedal as
you press the accelerator pedal.
You can shift into FIRST (1) when you're going less
than 20 mph (32 km/h). If you've come to a complete
stop and it's hard to shift into FIRST (1), put the shift
lever in NEUTRAL and let up on the clutch. Press the
clutch pedal back down. Then shift into FIRST (1).

2-22
Four-Wheel Drive (If Equipped)
If your vehicle has four-wheel drive, you can send
your engine's driving power to all four wheels for extra
traction. To shift out of two
-wheel drive and into
four
-wheel drive, move the transfer case shift lever to
FOUR
-WHEEL HIGH (4H) or FOUR-WHEEL
LOW (4L) (see the following). You should use
TWO
-WHEEL HIGH (2H) for most normal driving.
NOTICE:
Driving in FOUR-WHEEL HIGH (4H) or
FOUR
-WHEEL LOW (4L) positions for a long
time on dry or wet pavement could shorten the
life of your vehicle's drivetrain.
Transfer Case
The transfer case shift lever is on the floor to the right
of the driver. Use this lever to shift into and out of
four
-wheel drive. An indicator light comes on when the
transfer case is in FOUR
-WHEEL HIGH (4H) or
FOUR
-WHEEL LOW (4L).

2-24
Parking Brake
To set the parking brake, hold the brake pedal down and
pull up on the parking brake lever. If the ignition is on,
the brake system warning light will come on.To release the parking brake, hold the brake pedal down.
Pull the parking brake lever up until you can push in the
release button. Hold the release button in as you move
the lever all the way down.
NOTICE:
Driving with the parking brake on can cause
your rear brakes to overheat. You may have to
replace them, and you could also damage other
parts of your vehicle.
If you are towing a trailer, see ªTowing a Trailerº in
the Index.

2-31
Express Down Window
The AUTO switch for the driver's window has an
express down feature. To use express down, push the
switch all the way down. Release the switch and the
window will lower completely. Pull up on the switch
lightly and release it to stop the window partway.
Lock
-Out Switch
The driver's door has a lock
-out switch for the
passenger window(s). When you push the right side of
the switch you lock the passenger window(s) so they can
not be raised or lowered. Push the left side of the switch
to unlock the window(s).
When the window lock
-out switch is engaged, all
passenger window switches will not operate, including
the driver's controls.
Horn
To sound the horn, press the portion of your steering
wheel marked with the horn symbol.
Tilt Wheel
A tilt steering wheel allows you to adjust the steering
wheel before you drive. You can also raise it to the
highest level to give your legs more room when you exit
and enter the vehicle.
To tilt the wheel, hold the steering wheel and move the
lever down. Move the steering wheel to a comfortable
level, then release the lever to lock the wheel in place.

2-33 Headlamp High/Low Beam Changer
First, you must have the headlamps on. For high beams,
push the turn signal lever toward the instrument panel.
When the high beams are
on, a light on the instrument
panel cluster also will be on.
It will go off when you
switch to low beam.
To switch back to low beams, pull the lever toward you.
Flash-to-Pass
With the lever in the low-beam position, pull the lever
toward you to momentarily switch to high beam (to
signal that you are going to pass). When you release the
lever, the headlamps will return to low
-beam operation.
Windshield Wipers
The lever on the right side of the steering column
controls the windshield wipers and washers.
You control the windshield wipers by moving the stalk
up or down.
For steady wiping at low speed, move the stalk down
to LO. For higher speed wiping, move the stalk down
further to HI. To stop the wiper, move the stalk to OFF.

2-36
CAUTION:

Cruise control can be dangerous where
you can't drive safely at a steady speed.
So, don't use your cruise control on
winding roads or in heavy traffic.

Cruise control can be dangerous on
slippery roads. On such roads, fast changes
in tire traction can cause needless wheel
spinning, and you could lose control.
Don't use cruise control on slippery roads.
Setting Cruise Control
CAUTION:
If you leave your cruise control switch on when
you're not using cruise, you might hit a button
and go into cruise when you don't want to. You
could be startled and even lose control. Keep the
cruise control switch off until you want to use
cruise control.
1. Press the CRUISE
CTRL. switch on the
instrument panel to turn
the system on. The
indicator light on the
switch will come on.
2. Get up to the speed you want.
3. Once you're going 25 mph (40 km/h) or more, turn
the lever to COAST SET and release. Your cruise
will set.
4. Take your foot off the accelerator pedal.
Resuming a Set Speed
If you set your cruise control at a desired speed and then
apply the brake, this will turn off the cruise control
function. But you don't need to reset it.

2-37
If your speed has not dropped below 25 mph (40 km/h),
you can turn the lever to RESUME ACCEL for about
one second. You'll go right back to your chosen speed
and stay there. When your speed drops below 25 mph
(40 km/h), the system will not resume to your
previously chosen speed. You must reset your speed.
Increasing Speed While Using Cruise Control
There are two ways to go to a higher speed.

Use the accelerator pedal to go to a higher speed.
Turn the lever to COAST SET and release. Take
your foot off the accelerator pedal. You'll now cruise
at the higher speed.

Turn the lever to RESUME ACCEL. Hold the lever
at RESUME ACCEL until you get up to the speed
you want, then release the lever.
Reducing Speed While Using Cruise Control
To reduce your speed, turn and hold the lever in the
COAST SET position until you reach the lower speed
you want, then release the lever.
Passing Another Vehicle While Using Cruise Control
Use the accelerator pedal to increase your speed. When
you take your foot off the pedal, your vehicle will slow
down to the cruise control speed you set earlier.Using Cruise Control on Hills
How well your cruise control will work on hills depends
upon your speed, load and the steepness of the hills.
When going up steep hills, you may have to step on the
accelerator pedal to maintain your speed. When going
downhill, you may have to brake or shift to a lower gear
to keep your speed down. Of course, applying the brake
takes you out of cruise control. Many drivers find this to
be too much trouble and don't use cruise control on
steep hills.
Getting Out of Cruise Control
There are three ways to turn off cruise control:

Step lightly on the brake pedal, or push the clutch
pedal if you have a manual transmission.

Push in the CANCEL button on the end of the cruise
control lever.

Press the CRUISE CTRL. switch on the
instrument panel.
Erasing Speed Memory
When you turn off the cruise control or the ignition,
your cruise control set speed memory is erased.

2-38
Exterior Lamps
Turn the outside part of the lever to control the lamps.
There are three positions for the lamp switch.
Parking Lamps
: This position will turn on the following:

Parking Lamps

Sidemarker Lamps

Taillamps

Instrument Panel Lights

License Plate Lamp
Headlamps
: This position will turn on the following:

Headlamps

Parking Lamps

Sidemarker Lamps

Taillamps

Instrument Panel Lights

License Plate Lamp
Turn the switch to OFF to turn off the lamps.

2-39 Daytime Running Lamps
Daytime Running Lamps (DRL) can make it easier for
others to see the front of your vehicle during the day.
DRL can be helpful in many different driving
conditions, but they can be especially helpful in the
short periods after dawn and before sunset.
The DRL system will make your headlamps come on at
a reduced brightness when:

The ignition is on with the engine running,

the headlamp switch is off or the parking lights
are on, and

the parking brake is released.
When the DRL are on, only your headlamps will be on
at a reduce brightness. The taillamps, sidemarker and
other lamps won't be on. Your instrument panel won't
be lit up either.When you turn on the headlamp switch, your DRL will go
off and your headlamps will come on. The other lamps
that come on with your headlamps will also come on.
When it begins to get dark, the headlamps will
automatically switch from DRL to the regular headlamps.
See ªAutomatic Light Controlº later in this section.
When you turn the headlamp switch to off, the regular
lamps will go off and your headlamps will change to
the reduced brightness of DRL provided it is not dark
outside. DRL will also come on if only the parking
lamps are being used.
To idle your vehicle with the DRL off, set the parking
brake. The DRL will stay off until you release the
parking brake.
As with any vehicle, you should turn on the regular
headlamp system when you need it.