turn signal bulb CHRYSLER 200 2015 2.G Owners Manual

Multifunction Lever
The multifunction lever controls the operation of the turn
signals, headlight beam selection and passing lights. The
multifunction lever is located on the left side of the
steering column.
Turn Signals
Move the multifunction lever up or down and the arrows
on each side of the instrument cluster flash to show
proper operation of the front and rear turn signal lights.
NOTE:
•
If either light remains on and does not flash, or there is a
very fast flash rate, check for a defective outside light
bulb. If an indicator fails to light when the lever is moved,
it would suggest that the indicator bulb is defective.
•A “Turn Signal On” message will appear in the EVIC/DID
and a continuous chime will sound if the vehicle is driven
more than 1 mile (1.6 km) with either turn signal on.
• When the Daytime Running Lights are on and a turn
signal is activated, the Daytime Running Lamp will
turn off on the side of the vehicle in which the turn
signal is flashing. The Daytime Running Lamp will
turn back on when the turn signal is turned off.
Multifunction Lever
3
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 165

6. Adaptive Cruise Control (ACC) Distance Setting Dis-
playThis will display the distance setting for the
ACC system. For further information, refer to
“Adaptive Cruise Control (ACC)” in “Under-
standing The Features Of Your Vehicle”.
7. Seat Belt Reminder Light
When the ignition switch is first turned to the
ON/RUN position, this light will turn on for four
to eight seconds as a bulb check. During the bulb
check, if the driver’s seat belt is unbuckled, a chime will
sound. After the bulb check or when driving, if the driver
or front passenger seat belt remains unbuckled, the Seat
Belt Indicator Light will flash or remain on continuously.
Refer to “Occupant Restraints” in “Things To Know
Before Starting Your Vehicle” for further information. 8. Turn Signal Indicators
The arrows will flash with the exterior turn
signals when the turn signal lever is operated.
A tone will chime, and an EVIC/DID message
will appear if either turn signal is left on for
more than 1 mile (1.6 km).
NOTE: If either indicator flashes at a rapid rate, check for
a defective outside light bulb.
9. Electronic Stability Control (ESC)
The “ESC Activation/Malfunction Indicator
Light” in the instrument cluster will come on
when the ignition switch is turned to the
ON/RUN position. It should go out with the
engine running. If the “ESC Activation/Malfunction In-
dicator Light” comes on continuously with the engine
running, a malfunction has been detected in the ESC
system. If this light remains on after several ignition
4
UNDERSTANDING YOUR INSTRUMENT PANEL 325

▫Automatic Transmission ................617
▫ Appearance Care And Protection From
Corrosion .......................... .619
 FUSES ............................. .625
▫ Power Distribution Center (Fuses) ..........626
▫ Interior Fuses ....................... .635
 VEHICLE STORAGE ....................636
 REPLACEMENT BULBS .................637
 BULB REPLACEMENT ..................639
▫ Low Beam And High Beam Headlamps .....639
▫ Front Turn Signal Lamp ................642 ▫
Front Side Marker Lamps ...............644
▫ Front Fog Lamp ..................... .645
▫ Backup Lamps (Passenger Side) ...........646
▫ Backup Lamps (Driver Side) ..............648
▫ Stop/Rear Turn Signal Lamp .............649
▫ License Plate Lamp ....................650
 FLUID CAPACITIES ....................651
 FLUIDS, LUBRICANTS AND GENUINE
PARTS ............................. .652
▫ Engine ............................ .652
▫ Chassis ........................... .655
588 MAINTAINING YOUR VEHICLE

Exterior Bulbs
Bulb Number
High Intensity Discharge Headlamp HID (Serviced at Authorized Dealer)
Bi-Halogen Headlamp HIR2
Daytime Running Lamp LED (Serviced at Authorized Dealer)
Front Turn Signal Lamp PWY24W SV
Side Marker Lamp W3W
Front Park Lamp LED (Serviced at Authorized Dealer)
Front Fog Lamp H11
LED Front Fog Lamp LED (Serviced at Authorized Dealer)
Center High Mounted Stop (CHMSL) Lamp LED (Serviced at Authorized Dealer)
Stop/Turn Signal Lamp W21W
Rear Tail/Side Marker Lamp LED (Serviced at Authorized Dealer)
Backup Lamp 921
License Lamp W5W
638 MAINTAINING YOUR VEHICLE

6. Install the bulb and connector assembly into theheadlamp housing and rotate clockwise to lock it in
place.
7. Install the headlamp bulb cap in the headlamp hous- ing and rotate clockwise to lock it in place.
8. Lock headlamp access door in wheel liner.
Front Turn Signal Lamp
1. Open the hood.
NOTE: Removal of the air cleaner filter housing may be
necessary prior to replacing bulbs in the lamp assembly
on the passenger side of the vehicle.
2. Remove the beauty cover, by removing the 10 push pins. 3. Remove the brace by removing the four fasteners and
loosening the 5th inboard fastener.
4. Twist the front turn signal lamp socket assembly counterclockwise, and then remove the front turn
signal lamp assembly from the lamp housing.
Beauty Cover
642 MAINTAINING YOUR VEHICLE

5. Pull the bulb out of the socket and insert the replace-ment bulb.
6. Install the front turn signal lamp socket assembly into the housing, and rotate the front turn signal lamp
socket clockwise to lock it in place. 7. Install air cleaner filter housing, if removed.
8. Install brace, brace bolts and tighten as shown.
9. Install beauty cover.
Front Turn Signal Lamp Socket
Brace Bolt Tightening Sequence
7
MAINTAINING YOUR VEHICLE 643

4. Pull the tail lamp housing directly rearward to dis-lodge the two out bored ball studs from the socket
fasteners.
NOTE: It may be necessary to use significant force to
remove the two out bored ball studs from the socket
fasteners to remove the tail lamp housing. 5. Rotate the stop/rear turn signal lamp socket 1/4 turn
counterclockwise and remove it from the tail lamp
housing.
6. Remove the bulb from the socket and install the replacement bulb.
7.
Install the bulb socket into the tail lamp housing and
rotate the bulb socket ¼ turn clockwise to lock it in place.
8. Install the tail lamp housing.
9. Install the tail lamp housing beauty cover.
License Plate Lamp
1. Remove the screw of the license plate lamp assembly and pull down on the license plate lamp assembly to
remove.
2. Remove the bulb from the socket and install the replacement bulb.
3. Install the license plate lamp assembly.
Tail Lamp Bolts
650 MAINTAINING YOUR VEHICLE

Lock The Vehicle’s Doors..................24
Passive Entry ...........................36
Passive Entry Programming .................36
Remote Control .........................36
Unlock From The Driver’s Side ..............23
Unlock From The Passenger Side .............23
Keyless Entry System .......................22
Keyless Go ...............................12
Keys ...................................12
Lane Change and Turn Signals ................165
Lane Change Assist ....................... .166
Lap/Shoulder Belts .........................50
Latches ................................113
Lead Free Gasoline ....................... .531
Leaks, Fluid .............................113
Life of Tires ............................ .514
Light Bulbs ..............................113
Light Replacement ....................... .637Lights
.................................113
Airbag ................................82
Anti-Lock ............................ .328
Automatic Headlights ....................160
Battery Saver ......................... .170
Brake Assist Warning ....................491
Brake Warning ........................ .323
Bulb Replacement ...................... .639
Daytime Running ...................... .163
Dimmer Switch, Headlight .................165
Electronic Stability Program (ESP) Indicator .....491
Exterior ..............................113
Fog ................................ .164
Front Replacement ..................... .644
Hazard Warning Flasher ..................549
Headlights ........................... .159
Headlights On Reminder ..................163
Headlights On With Wipers ................161
Headlight Switch ...................... .159
684 INDEX