jump start CHRYSLER 200 2017 2.G Owners Manual
[x] Cancel search | Manufacturer: CHRYSLER, Model Year: 2017, Model line: 200, Model: CHRYSLER 200 2017 2.GPages: 539, PDF Size: 5.18 MB
Page 347 of 539
Extended Park Starting
NOTE:Extended Park condition occurs when the vehicle
has not been started or driven for at least 30 days.
1. Install a battery charger or jumper cables to the battery to ensure a full battery charge during the crank cycle.
2. Cycle the ignition in the START position and release it when the engine starts.
3. If the engine fails to start within 10 to 15 seconds, cycle the ignition to the STOP (OFF/LOCK) position, wait
five seconds to allow the starter to cool, then repeat the
Extended Park Starting procedure.
4. If the engine fails to start after eight attempts, allow the starter to cool for at least 10 minutes, then repeat the
procedure.
CAUTION!
To prevent damage to the starter, do not crank continu-
ously for more than 10 seconds at a time. Wait 10 to 15
seconds before trying again.
If Engine Fails To Start
WARNING!
•Never pour fuel or other flammable liquid into the
throttle body air inlet opening in an attempt to start
the vehicle. This could result in flash fire causing
serious personal injury.
• Do not attempt to push or tow your vehicle to get it
started. Vehicles equipped with an automatic trans-
mission cannot be started this way. Unburned fuel
could enter the catalytic converter and once the
engine has started, ignite and damage the converter
and vehicle.
• If the vehicle has a discharged battery, booster cables
may be used to obtain a start from a booster battery
or the battery in another vehicle. This type of start
can be dangerous if done improperly. Refer to
“Jump-Starting” in “What To Do In Emergencies” for
further information.
With Tip Start
If the engine fails to start after you have followed the
Normal Starting, “Extreme Cold Weather andExtended
5
STARTING AND OPERATING 345
Page 415 of 539
WHAT TO DO IN EMERGENCIES
CONTENTS
HAZARD WARNING FLASHERS ............414
IF YOUR ENGINE OVERHEATS .............414
WHEEL AND TIRE TORQUE SPECIFICATIONS . .415
▫ Torque Specifications ....................415
TIRE SERVICE KIT — IF EQUIPPED ..........416
▫ Tire Service Kit Storage ...................417
▫ Tire Service Kit Components And Operation . . . .418
▫ Tire Service Kit Usage Precautions ..........419
▫ Sealing A Tire With Tire Service Kit ..........420
JACKING AND TIRE CHANGING ...........425
▫ Jack Location/Spare Tire Stowage ...........425
▫ Preparations For Jacking .................426
▫ Jacking Instructions .....................427 ▫
Road Tire Installation ....................433
JUMP-STARTING PROCEDURES ............435
▫ Preparations For Jump-Start ...............436
▫ Jump-Starting Procedure ..................437
FREEING A STUCK VEHICLE ..............438
MANUAL PARK RELEASE .................439
TOWING A DISABLED VEHICLE ............442
▫ Front-Wheel Drive (FWD) Models ..........444
▫ All-Wheel Drive (AWD) Models ............444
ENHANCED ACCIDENT RESPONSE
SYSTEM (EARS) ....................... .445
EVENT DATA RECORDER (EDR) ............445
6
Page 437 of 539
8. After 25 miles (40 km) check the wheel bolt torque witha torque wrench to ensure that all wheel bolts are
properly seated against the wheel.
Road Tire Installation
1. Mount the road tire on the axle.
2. Install the remaining wheel bolts and lightly tighten.
WARNING!
To avoid the risk of forcing the vehicle off the jack, do
not tighten the lug nuts fully until the vehicle has been
lowered. Failure to follow this warning may result in
serious injury.
3. Lower the vehicle to the ground by turning the jack handle counterclockwise.
4. Finish tightening the wheel bolts. Push down on the wrench while at the end of the handle for increased
leverage. Tighten the wheel bolts in a star pattern until
each wheel bolt has been tightened twice. Refer to
“Torque Specifications” in this section for the proper lug
bolt torque. If in doubt about the correct tightness, have
them checked with a torque wrench by your authorized
dealer or service station. 5. Lower the jack until it is free. Remove the wheel chocks.
Reassemble the lug wrench to the jack assembly and
stow it in the spare tire area. Secure the assembly using
the means provided. Release the parking brake before
driving the vehicle.
6. After 25 miles (40 km) check the wheel bolt torque with a torque wrench to ensure that all wheel bolts are
properly seated against the wheel.
JUMP-STARTING PROCEDURES
If your vehicle has a discharged battery it can be jump-
started using a set of jumper cables and a battery in another
vehicle or by using a portable battery booster pack. Jump-
starting can be dangerous if done improperly so please
follow the procedures in this section carefully.
NOTE: When using a portable battery booster pack follow
the manufacturer ’s operating instructions and precautions.
WARNING!
Do not attempt jump-starting if the battery is frozen. It
could rupture or explode and cause personal injury.
6
WHAT TO DO IN EMERGENCIES 435
Page 438 of 539
CAUTION!
Do not use a portable battery booster pack or any other
booster source with a system voltage greater than 12
Volts or damage to the battery, starter motor, alternator
or electrical system may occur.
Preparations For Jump-Start
The battery in your vehicle is located in the front of the
engine compartment, behind the left headlight assembly.
WARNING!
•Take care to avoid the radiator cooling fan whenever
the hood is raised. It can start anytime the ignition
switch is ON. You can be injured by moving fan
blades.
• Remove any metal jewelry such as rings, watch
bands and bracelets that could make an inadvertent
electrical contact. You could be seriously injured.
• Batteries contain sulfuric acid that can burn your
skin or eyes and generate hydrogen gas which is
flammable and explosive. Keep open flames or
sparks away from the battery.
1. Set the parking brake, shift the automatic transmission into PARK and turn the ignition to LOCK.
2. Turn off the heater, radio, and all unnecessary electrical accessories.
3. If using another vehicle to jump-start the battery, park the vehicle within the jumper cables reach, set the
parking brake and make sure the ignition is OFF.
1 — Positive Battery Post
2 — Negative Battery Post 436 WHAT TO DO IN EMERGENCIES
Page 439 of 539
WARNING!
Do not allow vehicles to touch each other as this could
establish a ground connection and personal injury
could result.
Jump-Starting Procedure
WARNING!
Failure to follow this jump-starting procedure could
result in personal injury or property damage due to
battery explosion.
CAUTION!
Failure to follow these procedures could result in
damage to the charging system of the booster vehicle
or the discharged vehicle.
Connecting The Jumper Cables
1. Connect the positive (+)end of the jumper cable to the
positive (+)post of the discharged vehicle.
2. Connect the opposite end of the positive (+)jumper
cable to the positive (+)post of the booster battery. 3. Connect the negative
(-)end of the jumper cable to the
negative (-)post of the booster battery.
4. Connect the opposite end of the negative (-)jumper
cable to a good engine ground (exposed metal part of
the discharged vehicle’s engine) away from the battery
and the fuel injection system.
WARNING!
Do not connect the jumper cable to the negative (-) post
of the discharged battery. The resulting electrical spark
could cause the battery to explode and could result in
personal injury. Only use the specific ground point, do
not use any other exposed metal parts.
5. Start the engine in the vehicle that has the booster battery, let the engine idle a few minutes, and then start
the engine in the vehicle with the discharged battery.
6. Once the engine is started, remove the jumper cables in the reverse sequence:
Disconnecting The Jumper Cables
1. Disconnect the negative (-)end of the jumper cable from
the engine ground of the vehicle with the discharged
battery.6
WHAT TO DO IN EMERGENCIES 437
Page 440 of 539
2. Disconnect the opposite end of the negative(-)jumper
cable from the negative (-)post of the booster battery.
3. Disconnect the positive (+)end of the jumper cable from
the positive (+)post of the booster battery.
4. Disconnect the opposite end of the positive (+)jumper
cable from the positive (+)post of the vehicle with the
discharged battery.
If frequent jump-starting is required to start your vehicle
you should have the battery and charging system in-
spected at your authorized dealer.
CAUTION!
Accessories plugged into the vehicle power outlets
draw power from the vehicle’s battery, even when not
in use (i.e., cellular devices, etc.). Eventually, if plugged
in long enough without engine operation, the vehicle’s
battery will discharge sufficiently to degrade battery
life and/or prevent the engine from starting.
FREEING A STUCK VEHICLE
If your vehicle becomes stuck in mud, sand or snow, it can
often be moved using a rocking motion. Turn the steering
wheel right and left to clear the area around the front wheels. Then shift back and forth between DRIVE and
REVERSE while gently pressing the accelerator.
NOTE:
Shifts between DRIVE and REVERSE can only be
achieved at wheel speeds of 5 mph (8 km/h) or less.
Whenever the transmission remains in NEUTRAL for more
than two seconds, you must press the brake pedal to
engage DRIVE or REVERSE.
Use the least amount of accelerator pedal pressure that will
maintain the rocking motion without spinning the wheels
or racing the engine.
NOTE: Push the ESC Off switch to place the Electronic
Stability Control (ESC) system in Partial Offmode, before
rocking the vehicle. Refer to “Electronic Brake Control” in
“Starting And Operating” for further information. Once
the vehicle has been freed, push the ESC Offswitch again
to restore ESC Onmode.
WARNING!
Fast spinning tires can be dangerous. Forces generated
by excessive wheel speeds may cause damage, or even
failure, of the axle and tires. A tire could explode and
injure someone. Do not spin your vehicle’s wheels
(Continued)
438 WHAT TO DO IN EMERGENCIES
Page 460 of 539
assure most efficient service. MOPAR engine air cleaner
filters are a high quality filter and are recommended.
Maintenance-Free Battery
Your vehicle is equipped with a maintenance-free battery.
You will never have to add water, nor is periodic mainte-
nance required.
WARNING!
•Battery fluid is a corrosive acid solution and can
burn or even blind you. Do not allow battery fluid to
contact your eyes, skin, or clothing. Do not lean over
a battery when attaching clamps. If acid splashes in
eyes or on skin, flush the area immediately with
large amounts of water. Refer to “Jump-Starting
Procedures” in “What To Do In Emergencies” for
further information.
• Battery gas is flammable and explosive. Keep flame
or sparks away from the battery. Do not use a booster
battery or any other booster source with an output
greater than 12 Volts. Do not allow cable clamps to
touch each other.
(Continued)
WARNING! (Continued)
•Battery posts, terminals, and related accessories con-
tain lead and lead compounds. Wash hands after
handling.
CAUTION!
• It is essential when replacing the cables on the
battery that the positive cable is attached to the
positive post and the negative cable is attached to the
negative post. Battery posts are marked positive (+)
and negative (-) and are identified on the battery
case. Cable clamps should be tight on the terminal
posts and free of corrosion.
• If a “fast charger” is used while the battery is in the
vehicle, disconnect both vehicle battery cables before
connecting the charger to the battery. Do not use a
“fast charger” to provide starting voltage.
Air Conditioner Maintenance
For best possible performance, your air conditioner should
be checked and serviced by an authorized dealer at the
start of each warm season. This service should include
458 MAINTAINING YOUR VEHICLE
Page 526 of 539
Emergency, In Case OfHazard Warning Flasher ...................414
Jacking ............................... .425
Jump Starting .......................... .435
Overheating ........................... .414
Towing ............................... .442
Emergency Trunk Release .....................35
Emission Control System Maintenance ............452
Engine .............................. .449, 450
Air Cleaner ............................ .457
Block Heater ........................... .346
Break-In Recommendations ..................81
Checking Oil Level ...................... .454
Coolant (Antifreeze) ..................... .501
Cooling .............................. .464
Exhaust Gas Caution ...................82, 403
Fails To Start ........................... .345
Flooded, Starting ........................ .345
Fuel Requirements ....................... .400
Jump Starting .......................... .435
Oil ........................... .454, 500, 501
Oil Filler Cap .....................449, 450, 456
Oil Filter .............................. .457
Oil Selection ........................ .455, 500
Oil Synthetic ........................... .456Overheating
........................... .414
Starting .............................. .344
Engine Oil Viscosity ........................ .456
Engine Oil Viscosity Chart ....................456
Enhanced Accident Response Feature ..........63, 445
Entry System, Illuminated .....................16
Ethanol ............................. .400, 403
Exhaust Gas Caution .....................82, 403
Exhaust System ........................ .82, 463
Exterior Lighting ....................... .122, 494
Exterior Lights ......................... .85, 494
Filters Air
Cleaner ............................ .457
Air Conditioning .....................320, 459
Engine Oil ......................... .457, 501
Engine Oil Disposal ...................... .457
Flashers Hazard Warning ........................ .414
Turn Signal ....................85, 126, 267, 492
Flash-To-Pass ............................ .127
Flexible Fuel Vehicles Cruising Range ......................... .405
Engine Oil ............................ .404
Fuel Requirements ....................403, 404
524 INDEX
Page 528 of 539
Delay................................ .123
High Beam/Low Beam Select Switch ...........127
Lights On Reminder ..................... .125
On With Wipers ........................ .123
Passing ............................... .127
Replacing ............................. .490
Switch ............................... .122
Time Delay ............................ .123
Head Restraints ............................114
Head Rests ...............................114
Heated Mirrors ........................... .100
Heater, Engine Block ....................... .346
High Beam/Low Beam Select (Dimmer) Switch .....127
Hill Start Assist ........................... .367
Holder, Coin ............................. .232
HomeLink (Garage Door Opener) ...............213
Ignition Key....................................9
Illuminated Entry ...........................16
Courtesy Lights ..........................16
Front Courtesy Overhead Console .............16
Illuminated Entry .........................16
Remote Keyless Entry Key Fob ................16
Inside Rearview Mirror .......................93 Instrument Cluster
............244, 251, 254, 263, 267
Instrument Cluster ...................... .273
Instrument Panel And Controls .................243
Instrument Panel Lens Cleaning ................476
Interior Appearance Care .....................474
Interior Fuses ............................ .487
Interior Lights ............................ .128
Intermittent Wipers (Delay Wipers) ..............131
Introduction ................................4
Inverter Outlet (115V) ...................... .229
Jacking Instructions ........................ .427
Jack Location ............................ .425
Jack Operation ........................ .425, 427
Jump Starting ............................ .435
Key Fob Emer
gency Key ...........................10
Lock The Doors ..........................18
Panic Alarm .............................19
Programming Additional Key Fobs ..........14, 19
Remote Battery Replacement .................19
Remote Keyless Entry ....................10, 17
Unlatch The Trunk ........................18
Unlock The Doors .........................17
526 INDEX