spare tire CHRYSLER 300 2019 Vehicle Warranty

For all types of tires, consult your vehicle tire placard or owner ’s manual
for recommended operating pressures. If the tires are purchased as
replacement tires, operating instructions for the low pressure warning
system will be provided by the manufacturer of that system. Recom-
mended operating pressures will be provided by a participating Michelin
tire retailer for self supporting ZP tires. Recommended operating pres-
sure for PAX System Tires will be provided by a PAX System retailer.
These inflation pressures must be maintained as a minimum. However,
do not exceed the maximum pressure rating indicated on the tire
sidewall.
CHECK THE COLD INFLATION PRESSURES IN ALL YOUR TIRES,
INCLUDING THE SPARE, AT LEAST ONCE EACH MONTH
Failure to maintain correct inflation may result in improper vehicle
handling and may cause rapid and irregular tire wear, sudden tire
destruction, loss of vehicle control and serious personal injury. Therefore,
inflation pressures should be checked at least once each month and
always prior to long distance trips. This applies to all tires, including
sealant types, and Self-Supporting Zero Pressure (ZP) tires which are as
susceptible to losing air pressure as any other type of tire if not properly
maintained.
UNDERINFLATION
It is impossible to determine whether tires are properly inflated by
simply looking at them. It is almost impossible to “feel or hear” when a
tire is being run underinflated or nearly flat. Tires must be checked
monthly with a tire pressure gauge.
Pressures should be checked when tires are cold, in other words, before
they have been driven on. Driving, even for a short distance, causes tires
to heat up and air pressure to increase.
Checking pressure when tires are hot:
If pressures are checked after tires have been driven for more than three
minutes or more than one mile, (2 km) the tires become hot and the
pressures will increase by approximately 4 psi. Therefore when the tire
pressure is adjusted under these conditions, it should be increased to a
gauge reading of 4 psi greater than the recommended cold inflation
pressure.
MICHELIN
169

5 PSI from the previous pressure check, have the tire inspected at once
by an authorized PAX System Retailer for PAX tires or a participating
Michelin tire retailer (or representative of your vehicle manufacturer if
your vehicle owner ’s manual so advises.) Failure to do so may cause
irreparable damage to the tire and result in sudden tire destruction and
personal injury.
TIRE PRESSURE MONITORING SYSTEMS (TPMS):
Your vehicle may be equipped with a Tire Pressure Monitoring System
(TPMS) that is designed to monitor the pressure of tires mounted on your
vehicle and sends a signal to the driver if a tire pressure falls below a
predetermined level. A TPMS should not replace monthly manual
pressure checks for all four (4) tires and the spare. We recommend that
you manually monitor and check tire pressure inflation with a pressure
gauge. Your tires should have the recommended pressure listed by your
vehicle’s manufacturer. This information can be found in the vehicle
owner ’s manual and often on a placard located in the vehicle’s door
jamb, inside the fuel hatch, or on the glove compartment door. If you
have a plus size fitment that requires a higher inflation pressure, your tire
pressure monitoring system will require re-calibration to new inflation
pressure. Refer to your tire dealer/installer of plus size tires for proper
inflation pressure.
We recommend checking air pressure once each month, and before a long
trip. Whether you have a full-sized or mini-spare, make sure that it is
properly inflated as well. If the TPMS generates improper monitoring or
signals we recommend that you consult your owner ’s manual provided
with your vehicle and follow-up with your vehicle’s manufacturer.
TIRE SPINNING
Do not spin wheels in excess of 35 mph (55 km/h) as indicated on the
speedometer. Excessive speed in a free-running, unloaded tire can cause
it to “explode” from centrifugal force. The energy released by such an
explosion is sufficient to cause serious physical injury or death. Never
allow anyone to stand near or behind the spinning tire.
When in mud, sand, snow, ice or other slippery conditions, do not engage
in excessive wheel spin. Accelerating the motor excessively, particularly
with automatic transmission vehicles, may cause a drive tire that has lost
traction to spin beyond its speed capability. This is also true when
balancing a drive tire/wheel assembly on the vehicle using the vehicle
engine to spin the tire/wheel assembly.
MICHELIN
171

HIGH SPEED DRIVING CAN BE DANGEROUS
Correct inflation pressure is especially important.However, at high
speeds, even with the correct inflation pressure, a road hazard, for
example is more difficult to avoid and if contact is made, has a greater
chance of causing tire damage than at a lower speed. Moreover, driving
at high speed reduces the reaction time available to avoid accidents and
bring your vehicle to a safe stop. If you see any damage to a tire or
wheel, replace it with the spare at once and visit a participating
Michelin Tire Retailer.
Exceeding the maximum speeds shown on the following page for each
type of MICHELIN® tire will cause the tire to build up excessive heat
which can cause tire damage that could result in sudden tire destruction
and rapid air loss. Failure to control a vehicle when one or more tires
experience a sudden air loss can lead to an accident.
In any case, you should not exceed reasonable speeds as indicated by
the legal limits and driving conditions.
SPEED RATINGS
Speed Symbols are shown on the sidewall of some MICHELIN® tires.
The following table shows the maximum speed corresponding to the
symbol.
*Some V (or VR) rated tires may have a speed capacity greater than
149 mph (240 km/h). Consult your participating Michelin® tire retailer
for maximum speed rating if your vehicle capability exceeds this speed.
**Z (or ZR) rated tires are designed to use on cars with maximum speed
capabilities in excess of 149 mph (240 km/h).
(W and Y speed ratings are subcategories of Z).
Consult your Michelin tire retailer for maximum speed capabilities. For
PAX® System Tires consult an authorized PAX System Tire Retailer.
Although a tire may be speed-rated, we do not endorse the operation of
any vehicle in an unsafe or unlawful manner. Speed ratings are based on
laboratory tests which relate to performance on the road, but are not
applicable if tires are underinflated, overloaded, worn out, damaged,
altered, improperly repaired or retreaded.
MICHELIN
172

INSPECT YOUR TIRES, DO NOT DRIVE ON A DAMAGED TIRE
OR WHEEL
HAZARDS
Objects in the road, such as potholes, glass, metal, rocks, wood, debris
and the like, can damage a tire and should be safely avoided. Unavoid-
able contact with such objects should prompt a thorough tire inspection.
Anytime you see any damage to your tires or wheels, replace with the
spare at once and immediately visit any Michelin tire retailer. For PAX®
System Tires see an authorized PAX System tire retailer.
MICHELIN174

IMPACT DAMAGE
A tire impacted by a road hazard (curb, pothole, debris) may be damaged
but not have visible signs of damage on its surface. A tire damaged by an
impact may sustain a sudden failure a day, week, or even months later.
You may not recall hitting an object that damaged or injured your tires.
Air loss, unusual tire wear, localized wear or vibrations can also be signs
of internal tire damage.
If you suspect any damage to your tire or wheel from an impact with a
curb, pothole, debris on the road or any other road hazard, or if you feel
or hear any unusual vibration, replace with a properly inflated spare at
once and immediately visit any qualified tire technician.
INSPECTION
When inspecting your tires, including the spare, check the air pressures.
If the pressure check indicates that one of your tires has lost pressure of
two pounds or more, look for signs of penetration, valve leakage or wheel
damage that may account for the air loss.
Always look for bulges, cracks, cuts, penetrations, and abnormal tire
wear, particularly on the edges of the tire tread, which may be caused
by misalignment or underinflation. If any such damage is found, the
tire must be inspected by any Michelin tire retailer at once. Use of a
damaged tire could result in tire destruction.
All tires will wear out faster when subjected to high speeds as well as
hard cornering, rapid starts, sudden stops, frequent driving on roads
which are in poor condition, and off road use. Roads with holes and rocks
or other objects can damage tires and cause misalignment of your vehicle.
When driving on such roads, drive carefully and slowly, and before
driving again at normal or highway speeds, examine your tires for any
damage, such as cuts, bulges, penetrations, unusual wear patterns, etc.
WEAR BARS
MICHELIN® tires contain “Wear-Bars” in the grooves of the tire tread
which show up when only 2/32 nds of an inch (1.6 mm) of tread is
remaining. At this stage, your tires must be replaced. Tires worn beyond
this stage are extremely dangerous.
MICHELIN
175

checked immediately. Tires which have been run underinflated will show
more wear on the shoulders than in the center of the tread.
TIRE MIXING
MICHELIN® tires are radial tires and for best performance it is recom-
mended that the same size and type of tire be used on all four wheel
positions. Before mixing tires of different types in any configuration on
any vehicle, be sure to check the vehicle manufacturer ’s owner‘s manual
for its recommendations.
It is especially important to check the vehicle manufacturer ’s owner ’s
manual when mixing, matching, or replacing tires on 4-wheel drive
vehicles, as this may require special precautions.
MICHELIN DOES NOT RECOMMEND MIXING PAX® SYSTEM TIRES
WITH NON-PAX TIRES / SELF-SUPPORTING ZERO PRESSURE (ZP)
TIRES WITH NON-ZP TIRES OTHER THAN THE TEMPORARY USE
OF THE SPARE IF THE VEHICLE IS SO EQUIPPED.
WINTER DRIVING
Tires which meet the Rubber Manufactures Association (RMA) definition
of snow tires are marked M/S, or M&S. On such tires, this designation is
molded into the sidewall. Tires without this notation are not recom-
mended or winter driving.While All-Season tires are designed to provide reliable
performance in some winter conditions, the use of four
(4) winter tires is recommended for optimal performance.
Tires designate for use in severe winter conditions are
marked on at leas one sidewall with the letter “M”
TIRE ROTATION AND REPLACEMENT
To obtain maximum tire wear, it may be necessary to rotate your tires.
Refer to your vehicle owner ’s manual for instructions on tire rotation. If
you do not have an owner‘s manual for your vehicle, Michelin recom-
mends rotating your tires every 6,000 to 8,000 miles (10,000 to 12,000 km).
Monthly inspection for tire wear is recommended. Your tires should be
rotated at the first sign of irregular wear, even if it occurs before 6,000
miles (10,000 km). This is true for all vehicles.
MICHELIN
177

When rotating tires with a directional tread pattern, observe the arrows
molded on the sidewall which show the direction the tire should turn.
Care must be taken to maintain the proper turning direction.
Some Tire Pressure Monitoring Systems (TPMS) may not recognize
that a tire has been moved to a different position on your vehicle. Make
certain that your TPMS system is reset, if necessary, so as to correctly
identify the location of each tire on your vehicle. Refer to your vehicle
owner ’s manual or your vehicle dealer.
Determine whether rotated tires require tire inflation adjustment as front
and rear position tire pressure may vary according to the vehicle
manufacturer ’s specification due to the actual load on that wheel
position. Some vehicles may have different sized tires mounted on the
front and rear axles, and these different sized tires have rotation
restrictions. Always check the vehicle owner ’s manual for the proper
rotation recommendations.
Full-size Spare
Full-size spare tires (not temporary spares) of the same size and construc-
tion should be used in a five (5) tire rotation. Always check the inflation
pressure of the full-size spare immediately before incorporating it into
rotation. Follow the vehicle manufacturer ’s recommended pattern for
rotation, or if not available, see a qualified tire technician.
Replacement of Two (2) Tires
It is recommended that all four (4) tires are replaced at the same time.
However, when only two tires are replaced, the new tires should be put
on the rear. The new tires, with deeper tread, may provide better grip and
water evacuation in wet driving conditions.
CUSTOMIZATION OF TIRES, WHEELS, OR SUSPENSION ON
SUVS AND LIGHT TRUCKS
Due to their size, weight and higher center of gravity, vehicles such as
SUVs and light trucks do not have the same handling characteristics as
automobiles. Because of these differing characteristics, failure to operate
your SUV/truck in a proper and safe manner can increase the likelihood
of vehicle rollover. Modifications to your SUV/truck tire size, tire type,
wheels or suspension can change its handling characteristics and further
increase the likelihood of vehicle rollover. Whether your SUV/truck has
the original equipment configuration for tires, wheels and suspension or
whether any of these items have been modified, always drive safely,
MICHELIN178

sidewall of the tire. DO NOT MOUNT ZP TIRES WITH THE SH-M
DESIGNATION ON STANDARD WHEELS. IN SUCH APPLICATIONS,
THE TIRES MAY BECOME UNSERVICEABLE AT LOW OR ZERO
PRESSURE, CAUSING SERIOUS PERSONAL INJURY OR DEATH.
SPECIAL MOUNTING INSTRUCTIONS FOR MICHELIN® TRX™
TIRES
The MICHELIN® TRX™ tire is a tubeless tire that must only be mounted
on special wheels (TR or JM type) with millimetric seat diameter. If TRX
tires are mounted on standard wheels, they will not retain air due to an
air escape feature designed into the bead area of these tires.
Do not try to override this feature by mounting TRX tires with tubes.
The MICHELIN® TRX tire must be used on all wheel positions.
TEMPORARY TYPE SPARE TIRES
When using any temporary type spare tire, be sure to follow the vehicle
manufacturer ’s instructions.
READING THE DOT
DOT XXXX XXXX XXX (prior to August 2000)
DOT XXXX XXXX XXX (1990-1999)
DOT XXXX XXXX XXXX (after July 2000)
THE DOT
The “DOT” symbol certifies tire manufacturer ’s compliance with U.S.
Department of Transportation tire safety standards. Next to the symbol is
the tire identification or “serial number”. The first two characters identify
the plant where the tire was manufactured. The next two characters
reflect the tire size. The following one to four digits may be used at the
tire manufacturer ’s option as a descriptive code. The last three characters
are numbers identifying the week and year of manufacture. (Example:
“O25” means second week of the year of decade, eg.: 1995, 1985, etc.) For
the 1990-1999 decade MICHELIN® brand tires are marked with a triangle
pointing to the last three numeric characters. Tires produced after July
2000 have an additional digit to identify a given decade. For example,
2800 means the tire was produced during the 28th week of 2000; 0201
during the 2nd week of 2001. If the last digits of your DOT number
contains three numeric characters and is not marked with a triangle,
consult a qualified tire technician to determine the year of manufacture.
MICHELIN182

SERVICE LIFE FOR PASSENGER CAR AND LIGHT TRUCK
TIRES INCLUDING SPARE TIRES
The following recommendation applies to passenger car and light truck
tires. Tires are composed of various types of material and rubber
compounds, having performance properties essential to the proper
functioning of the tire itself. These component properties evolve over
time. For each tire, this evolution depends upon many factors such as
weather, storage conditions, and conditions of use (load, speed, inflation
pressure, maintenance etc.) to which the tire is subjected throughout its
life. This service-related evolution varies widely so that accurately
predicting the serviceable life of any specific tire in advance is not
possible.
That is why, in addition to regular inspections and inflation pressure
maintenance by consumers, it is recommended to have passenger car and
light truck tires, including spare tires, inspected regularly by a qualified
tire specialist, such as a tire dealer, who will assess the tire’s suitability for
continued service. Tires which have been in use for 5 years or more
should continue to be inspected by a specialist at least annually. Con-
sumers are strongly encouraged to be aware not only of their tires’ visual
condition and inflation pressure but also of any change in dynamic
performance such as increased air loss, noise or vibration, which could be
an indication that the tires need to be removed from service to prevent
tire failure. It is impossible to predict when tires should be replaced based
on their calendar age alone. However the older a tire the greater the
chance that it will need to be replaced due to the service-related evolution
or other conditions found upon inspection or detected during use.
While most tires will need replacement before they achieve 10 years, it is
recommended that any tires in service 10 years or more from the date of
manufacture, including spare tires, be replaced with new tires as a simple
precaution even if such tires appear serviceable and even if they have not
reached the legal wear limit. For tires that were on an original equipment
vehicle (i.e., acquired by the consumer on a new vehicle), follow the
vehicle manufacturer ’s tire replacement recommendations, when speci-
fied (but not to exceed 10 years).
The date when a tire was manufactured is located on the sidewall of each
tire. Consumers should locate the Department of Transportation or DOT
code on the tire which begins with DOT and ends with the week and year
of manufacture. For example, a DOT code ending with “2204” indicates
a tire made in the 22nd week (May) of 2004.
MICHELIN
183

REMEMBER... TO AVOID DAMAGE TO YOUR TIRES AND
POSSIBLE ACCIDENT:
•CHECK TIRE PRESSURE AT LEAST ONCE EACH MONTH WHEN
TIRES ARE COLD AND BEFORE LONG TRIPS.
• DO NOT UNDERINFLATE/OVERINFLATE.
• DO NOT OVERLOAD.
• DRIVE AT MODERATE SPEEDS, OBSERVE LEGAL LIMITS.
• AVOID DRIVING OVER POTHOLES, OBSTACLES, CURBS OR
EDGES OF PAVEMENT.
• AVOID EXCESSIVE WHEEL SPINNING.
• IF YOU SEE ANY DAMAGE TO A TIRE, REPLACE WITH THE
SPARE AND VISIT ANY MICHELIN® TIRE RETAILER AT ONCE.
• IF YOU HAVE ANY QUESTIONS. CONTACT YOUR MICHELIN
TIRE RETAILER.
FAILURE TO OBSERVE ANY OF THE RECOMMENDED PRECAU-
TIONS CONTAINED IN THIS OWNER’S MANUAL CAN LEAD TO
ERRATIC VEHICLE BEHAVIOR AND/OR TIRE DAMAGE, POSSI-
BLY RESULTING IN AN ACCIDENT.
If you see any damage to your tires or wheels, contact your local
participating Michelin® tire retailer listed in the Yellow Pages, or visit
our web site listed below for dealer locations. If further assistance is
required, contact:
IN USA 1-800-847-3435 or write:
Michelin North America, Inc.
Attention: Consumer Care Department Post Office Box 19001
Greenville, SC 29602-9001
or visit: www.michelinman.com.
IN CANADA 1-888-871-4444 or write:
Michelin North America (Canada) Inc.
3020 Jacques-Bureau Avenue Laval, QuebecH7P 6G2
or visit: www.michelin.ca.
MICHELIN
184