check engine CHRYSLER CARAVAN 2000 Owners Manual

TEST TC-76AREPAIRING - SMART START RELAY SHORT CIRCUIT
Perform TEST DTC Before Proceeding
*Perform Verification TEST VER-1A. **Check connectors - Clean / repair as necessary.
REPLACE THE
START TEST STARTER RELAY WITH
TC-76A. A KNOWN GOOD
RELAY.
FIG.1
FULLY DEPRESS THE
CLUTCH PEDAL AND DOES THE ENGINE YES REPLACE THE
ATTEMPT TO CRANK CRANK? INITIAL STARTER
THE ENGINE RELAY.
NO
KEY OFF.
REMOVE THE STARTER REMOVE THE DIESEL
DISCONNECT THE ECM RELAY.** POWER RELAY.**
HARNESS
CONNECTORS.**
WITH A JUMPER WIRE, KEY ON. USING A REPAIR THE STARTER
CONNECT DIESEL POWER TEST LIGHT, PROBE IS THE TEST LIGHT YES RELAY CONTROL
RELAY CONN. CAVITIES THE STARTER RELAY ON? CIRCUIT FOR A
30 AND 87 (IN PDC). CONTROL CIRCUIT. SHORT TO VOLTAGE.*
FIG.1 FIG.1
NO
REPLACE THE ENGINE
CONTROL MODULE.*
T
R
O
U
B
L
E
C
O
D
E
T
E
S
T
S
241
ProCarManuals.com

TEST TC-79ACONTINUED - REPAIRING - SOLENOID VALVE CONTROLLER OPEN CIRCUIT
*Perform Verification TEST VER-2A. **Check connectors - Clean / repair as necessary.
TEST TC-79A KEY OFF.
CONTINUED FROM DISCONNECT THE
THE PREVIOUS FUEL PUMP ASSEMBLY
PAGE. HARNESS
CONNECTOR.**
KEY ON. MEASURE FUEL
USE A VOLTMETER IN PUMP HARNESS IS THE VOLTAGE YES REPAIR THE OPEN
THE FOLLOWING CONNECTOR CAVITY 10. BELOW 10.5 VOLTS? DIESEL POWER RELAY
STEP.OUTPUT CIRCUIT*
FIG.1
NO
TURN IGNITION OFF. USING AN OHMMETER, REPAIR THE FUEL
DISCONNECT THE ECM MEASURE THE FUEL IS THE RESISTANCE YES TIMING SOLENOID
HARNESS TIMING SOLENOID BELOW 5.0 OHMS? CONTROL CIRCUIT
CONNECTORS.** CONTROL CIRCUIT TO FOR A SHORT TO
GROUND. FIG.1 GROUND.*
NO
MEASURE THE FUEL REPAIR THE OPEN
USE AN OHMMETER IN TIMING SOLENOID IS THE RESISTANCE YES FUEL TIMING
THE FOLLOWING CONTROL CKT BETWEEN ABOVE 5.0 OHMS? SOLENOID CONTROL
STEPS. THE ECM AND THE FUEL CIRCUIT.*
PUMP ASSEMBLY. FIG.2
NO
MEASURE THE PUMP CONNECTOR (PUMP
RESISTANCE OF THE SIDE) BETWEEN IS THE RESISTANCE NO REPLACE THE FUEL
FUEL TIMING CAVITIES 5 AND 10. BETWEEN 12.0 AND INJECTION PUMP
SOLENOID AT THE 20.0 OHMS? ASSEMBLY.*
INJECTION... FIG.3
YES
NOTE: BEFORE
REPLACING THE ECM, DID THE FUEL YES REPLACE THE ENGINE
PERFORM TEST NTC-3A INJECTION PUMP CONTROL MODULE.*
TO CHECK INTERNAL PASS TEST NTC-3A?
FUEL PUMP CIRCUITRY.
NO
REPLACE THE FUEL
INJECTION PUMP
ASSEMBLY.*
T
R
O
U
B
L
E
C
O
D
E
T
E
S
T
S
245
ProCarManuals.com

TEST TC-80ACONTINUED - REPAIRING - SOLENOID VALVE CONTROLLER SHORT CIRCUIT
*Perform Verification TEST VER-2A. **Check connectors - Clean / repair as necessary.
KEY OFF. KEY ON. ERASE CODES.
TEST TC-80A DISCONNECT THE DOES THE DRB DISPLAY YES REPLACE THE FUEL
CONTINUED FROM FUEL PUMP ASSEMBLY "FUEL TIMING PUMP ASSEMBLY.*
PREVIOUS PAGE. CONNECTOR.** SOLENOID CONTROLLER
OPEN CIRCUIT"?
NO
KEY OFF.
DISCONNECT THE ECM REMOVE THE DIESEL
HARNESS POWER RELAY.
CONNECTORS.**
WITH A JUMPER WIRE, KEY ON. USING A REPAIR THE FUEL
CONNECT DIESEL POWER VOLTMETER MEASURE IS THE VOLTAGE YES TIMING SOLENOID
RELAY CONN. CAVITIES THE FUEL TIMING ABOVE 1.0 VOLTS? CONTROL CIRCUIT
30 AND 87 (IN PDC). SOLENOID CONTROL FOR A SHORT TO
FIG.1 CKT. FIG.2 VOLTAGE.*
NO
NOTE: BEFORE
REPLACING THE ECM, DID THE FUEL YES REPLACE THE ENGINE
PERFORM TEST NTC-3A INJECTION PUMP CONTROL MODULE.*
TO CHECK INTERNAL PASS TEST NTC-3A?
FUEL PUMP CIRCUITRY.
NO
REPLACE THE FUEL
INJECTION PUMP
ASSEMBLY.*
T
R
O
U
B
L
E
C
O
D
E
T
E
S
T
S
249
ProCarManuals.com

TEST TC-81AREPAIRING - TEMPERATURE OF ENGINE COOLANT SRC HIGH EXCEEDED
Perform TEST DTC Before Proceeding
*Perform Verification TEST VER-2A. **Check connectors - Clean / repair as necessary.
WITH THE DRB, READ IS THE ENGINE
START TEST THE ENGINE COOLANT COOLANT YES CONTINUE TEST
TC-81A. TEMPERATURE SENSOR TEMPERATURE SENSOR TC-81A ON THE
VOLTAGE. VOLTAGE ABOVE 4.7 NEXT PAGE.
VOLTS?
NO
USE THE SCHEMATIC WAS THERE ANY REPAIR THE HARNESS
AS A GUIDE AND MONITOR THE DRB ENGINE COOLANT YES OR CONNECTOR THAT
WIGGLE THE ECT DISPLAY. TEMPERATURE SENSOR CAUSED THE VOLTAGE
SENSOR CONNECTOR & VOLTAGE CHANGE? CHANGE.*
HARNESS. FIG.1
NO
AT THIS TIME, THE USING THE
CONDITION REQUIRED SCHEMATIC AS A WERE ANY PROBLEMS YES REPAIR AS
TO SET THE CODE IS GUIDE, INSPECT THE FOUND? NECESSARY.*
NOT PRESENT. FIG.2 WIRING AND
CONNECTORS.
NO
REFER TO GENERAL
INFOMATION 3.3.2 FOR YES
ADDITIONAL TEST COMPLETE.*
INFORMATION ON
INTERMITTENT CODES.
T
R
O
U
B
L
E
C
O
D
E
T
E
S
T
S
251
ProCarManuals.com

TEST TC-81ACONTINUED - REPAIRING - TEMPERATURE OF ENGINE COOLANT SRC HIGH
EXCEEDED
*Perform Verification TEST VER-2A. **Check connectors - Clean / repair as necessary.
TEST TC-81A KEY OFF.
CONTINUED FROM DISCONNECT THE ECT
THE PREVIOUS SENSOR HARNESS
PAGE. CONNECTOR.**
KEY ON. MEASURE THE ECT REPAIR THE ECT
SIGNAL CIRCUIT. IS THE VOLTAGE YES SENSOR SIGNAL CKT
USE A VOLTMETER IN ABOVE 5.5 VOLTS? FOR A SHORT TO
THE FOLLOWINGVOLTAGE.* IF OK,
STEP. FIG.1 REPLACE THE ECM.*
NO
CONNECT A JUMPER WITH THE DRB, READ REPLACE THE ENGINE
BETWEEN THE ECT THE ENGINE COOLANT IS THE VOLTAGE YES COOLANT
SENSOR SIGNAL AND TEMPERATURE SENSOR BELOW 1.0 VOLT? TEMPERATURE
SENSOR GROUND CKT. VOLTAGE. SENSOR.*
FIG.1
NO
MOVE THE JUMPER WITH THE DRB, READ
WIRE FROM THE THE ENGINE COOLANT IS THE VOLTAGE YES REPAIR THE OPEN
SENSOR GROUND TO TEMPERATURE SENSOR BELOW 1.0 VOLT? SENSOR GROUND
AN ENGINE GROUND. VOLTAGE. CIRCUIT.*
FIG.1
NO
KEY OFF.
DISCONNECT THE ECM USE AN OHMMETER IN
HARNESS THE FOLLOWING
CONNECTORS.** STEP.
MEASURE THE ENGINE
COOLANT TEMEPERATURE IS THE RESISTANCE YES REPLACE THE ENGINE
SENSOR SIGNAL BELOW 5.0 OHMS? CONTROL MODULE.*
CIRCUIT.
FIG.2
NO
REPAIR THE OPEN
ENGINE COOLANT
TEMPERATURE SENSOR
SIGNAL CIRCUIT.*
T
R
O
U
B
L
E
C
O
D
E
T
E
S
T
S
253
ProCarManuals.com

TEST TC-82AREPAIRING - TEMPERATURE OF ENGINE COOLANT SRC LOW EXCEEDED
Perform TEST DTC Before Proceeding
*Perform Verification TEST VER-2A. **Check connectors - Clean / repair as necessary.
WITH THE DRB, READ IS THE ENGINE
START TEST THE ENGINE COOLANT COOLANT YES CONTINUE TEST
TC-82A. TEMPERATURE SENSOR TEMPERATURE SENSOR TC-82A ON THE
VOLTAGE. VOLTAGE BELOW NEXT PAGE.
0.3 VOLT?
NO
USING THE SCHEMATIC, WAS THERE ANY REPAIR THE HARNESS
WIGGLE THE ENGINE MONITOR THE DRB ENGINE COOLANT YES OR CONNECTOR THAT
COOLANT TEMPERATURE DISPLAY. TEMPERATURE SENSOR CAUSED THE VOLTAGE
SENSOR CONNECTOR & VOLTAGE CHANGE? CHANGE.*
HARNESS. FIG.1
NO
AT THIS TIME, THE USING THE
CONDITION REQUIRED SCHEMATIC AS A WERE ANY PROBLEMS YES REPAIR AS
TO SET THE CODE IS GUIDE, INSPECT THE FOUND? NECESSARY.*
NOT PRESENT. WIRING AND
FIG.2 CONNECTORS.
NO
REFER TO GENERAL
INFORMATION 3.3.2 YES
FOR ADDITIONAL TEST COMPLETE.*
INFORMATION ON
INTERMITTENT CODES.
T
R
O
U
B
L
E
C
O
D
E
T
E
S
T
S
255
ProCarManuals.com

TEST TC-82ACONTINUED - REPAIRING - TEMPERATURE OF ENGINE COOLANT SRC LOW
EXCEEDED
*Perform Verification TEST VER-2A. **Check connectors - Clean / repair as necessary.
TEST TC-82A DISCONNECT THE
CONTINUED FROM ENGINE COOLANT
THE PREVIOUS TEMPERATURE SENSOR
PAGE. HARNESS
CONNECTOR.**
WITH THE DRB, READ IS THE ENGINE REPLACE THE ENGINE
ENGINE COOLANT COOLANT YES COOLANT
TEMPERATURE SENSOR TEMPERATURE SENSOR TEMPERATURE
VOLTAGE. VOLTAGE ABOVE 4.0 SENSOR.*
VOLTS?
NO
KEY OFF. USING AN OHMMETER, REPAIR THE SENSOR
DISCONNECT THE ECM MEASURE BETWEEN THE IS THE RESISTANCE YES SIGNAL CIRCUIT FOR
HARNESS SENSOR SIGNAL BELOW 5.0 OHMS? A SHORT TO
CONNECTORS.** CIRCUIT AND GROUND. GROUND.*
FIG.1
NO
WITH AN OHMMETER SENSOR SIGNAL REPAIR THE ECT
MEASURE THE CIRCUIT AND THE IS THE RESISTANCE YES SENSOR SIGNAL
RESISTANCE BETWEEN SENSOR GROUND BELOW 5.0 OHMS? CIRCUIT FOR A SHORT
THE ENGINE COOLANT CIRCUIT. TO THE ECT SENSOR
TEMPERATURE... FIG.1 GROUND CIRCUIT.*
NO
REPLACE THE ENGINE
CONTROL MODULE.*
T
R
O
U
B
L
E
C
O
D
E
T
E
S
T
S
257
ProCarManuals.com

TEST TC-84AREPAIRING - TERMINAL 15 PLAUSIBILITY AFTER START-UP
Perform TEST DTC Before Proceeding
*Perform Verification TEST VER-2A. **Check connectors - Clean / repair as necessary.
START TEST WITH THE DRB,
TC-84A. ERASE CODES.
CYCLE THE IGNITION
ON AND OFF SEVERAL WITH THE IGNITION DOES THE DRB YES CONTINUE TEST
TIMES, PAUSING FOR ON ENGINE OFF, DISPLAY "TERMINAL TC-84A ON THE
TEN SECONDS AT KEY READ CODES. 15 PLAUSIBILITY"? NEXT PAGE.
ON AND OFF.
NO
AT THIS TIME THE REVIEW THE CIRCUIT
CONDITION FOR DESCRIPTION FOR A WERE ANY PROBLEMS YES REPAIR AS
SETTING THE CODE PROPER UNDERSTANDING FOUND? NECESSARY.*
IS NOT PRESENT. OF THIS CODE. CHECK
FIG. 1 FOR PROBLEMS.
NO
TEST COMPLETE.*
T
R
O
U
B
L
E
C
O
D
E
T
E
S
T
S
259
ProCarManuals.com

TEST TC-84ACONTINUED - REPAIRING - TERMINAL 15 PLAUSIBILITY AFTER START-UP
*Perform Verification TEST VER-2A. **Check connectors - Clean / repair as necessary.
TEST TC-84A KEY OFF.
CONTINUED FROM DISCONNECT THE ECM
THE PREVIOUS HARNESS
PAGE. CONNECTORS.**
USING A VOLTMETER, NOTE: BE SURE TO IS THE VOLTAGE
MEASURE ALL ECM EXCLUDE CAVITIES ABOVE 2.0 VOLTS NO REPLACE THE ENGINE
HARNESS CONNECTOR 30,33,45 AND 51 FOR ANY OF THE CONTROL MODULE.*
CAVITIES EXCEPT FROM THIS STEP. MEASUREMENTS?
30,33,45 AND 51.
YES
IS VOLTAGE PRESENT REPAIR SHORT TO
AT ECM HARNESS NO VOLTAGE ON THE
CONNECTOR CAVITIES CIRCUIT THAT
2 OR 28? MEASURED ABOVE 2.0
VOLTS.*
YES
USING A VOLTMETER, REPAIR THE SHORT
REMOVE THE DIESEL MEASURE ECM HARNESS IS THE VOLTAGE YES TO VOLTAGE ON THE
POWER RELAY.** CONNECTOR CAVITY 2. ABOVE 2.0 VOLTS? DIESEL POWER RELAY
OUTPUT CKT.*
FIG.1
NO
TURN IGNITION OFF. THE DIESEL POWER REPAIR THE SHORT
USING AN OHMMETER, RELAY CONTROL CKT. IS THE RESISTANCE YES TO GROUND ON THE
MEASURE BETWEEN AT THE PDC. BELOW 5.0 OHMS? DIESEL POWER RELAY
GROUND AND... CONTROL CKT.*
FIG.2
NO
REPLACE THE DIESEL
POWER RELAY.*
T
R
O
U
B
L
E
C
O
D
E
T
E
S
T
S
261
ProCarManuals.com

TEST TC-85ACONTINUED - REPAIRING - TIMING GOVERNING NEGATIVE GOVERNOR DEVIATION
*Perform Verification TEST VER-2A. **Check connectors - Clean / repair as necessary.
NOTE: THIS CODE REPAIR OTHER CODES
TEST TC-85A WILL SET DUE TO ARE ANY OTHER YES FIRST. CLEAR THIS
CONTINUED FROM NOISE ON THE CODES SET? CODE AND REPEAT
PREVIOUS PAGE. NEEDLE MOVEMENT DIAGNOSIS.*
SENSOR CIRCUIT.
NO
TEST DRIVE
REPLACE THE FUEL VEHICLE. USING THE DOES THE DRB YES REPLACE THE ENGINE
INJECTION PUMP DRB, DISPLAY DISPLAY THIS CODE? CONTROL MODULE.*
ASSEMBLY. CODES.
NO
TEST COMPLETED.*
T
R
O
U
B
L
E
C
O
D
E
T
E
S
T
S
265
ProCarManuals.com