turn signal CHRYSLER CARAVAN 2000 Owner's Manual

TEST TC-62ACONTINUED - REPAIRING - INTAKE AIR TEMPERATURE SENSOR SIGNAL HIGH
EXCEEDED
*Perform Verification TEST VER-2A. **Check connectors - Clean / repair as necessary.
TEST TC-62A KEY OFF.
CONTINUED FROM DISCONNECT THE
THE PREVIOUS BOOST PRESSURE
PAGE. SENSOR HARNESS
CONNECTOR.**
WITH A JUMPER WIRE, TURN IGNITION ON.
DISCONNECT THE ECM REMOVE THE DIESEL CONNECT DIESEL POWER
HARNESS POWER RELAY.** RELAY CONN. CAVITIES USE A VOLTMETER IN
CONNECTORS.** 30 AND 87 (IN PDC). THE FOLLOWING
FIG.1 STEP.
MEASURE THE IAT REPAIR THE INTAKE
SENSOR SIGNAL IS THE VOLTAGE YES AIR TEMPERATURE
CIRCUIT. ABOVE 1.0 VOLT? SENSOR SIGNAL
CIRCUIT FOR A
FIG.2 SHORT TO VOLTAGE.*
NO
KEY OFF. USING AN OHMMETER, REPAIR THE OPEN
MEASURE THE IAT IS THE RESISTANCE NO INTAKE AIR
REMOVE THE JUMPER SENSOR SIGNAL BELOW 5.0 OHMS? TEMPERATURE SENSOR
WIRE. CIRCUIT. SIGNAL CIRCUIT.*
FIG.3
YES
CONNECT A JUMPER DOES THE DRB
BETWEEN THE INTAKE WITH THE DRB, DISPLAY "INTAKE YES REPLACE THE BOOST
AIR TEMP SENSOR ERASE AND THEN AIR TEMPERATURE PRESSURE SENSOR.*
SIGNAL AND SENSOR READ CODES. SENSOR LOW
GROUND CKT. FIG.1 EXCEEDED"?
NO
MOVE THE JUMPER DOES THE DRB
WIRE FROM THE WITH THE DRB, READ DISPLAY "INTAKE YES REPAIR THE OPEN
SENSOR GROUND TO CODES. AIR TEMPERATURE SENSOR GROUND
AN ENGINE GROUND. SENSOR LOW CIRCUIT.*
EXCEEDED"?
NO
REPLACE THE ENGINE
CONTROL MODULE.*
T
R
O
U
B
L
E
C
O
D
E
T
E
S
T
S
219
ProCarManuals.com

TEST TC-91ACONTINUED - REPAIRING - VEHICLE SPEED SENSOR TROUBLE CODES
*Perform Verification TEST VER-2A. **Check connectors - Clean / repair as necessary.
KEY OFF.
TEST TC-91A
CONTINUED FROM DISCONNECT THE VSS
PREVIOUS PAGE. HARNESS
CONNECTOR.**
USING A VOLTMETER, REPAIR THE
MEASURE THE FUSED IS THE VOLTAGE NO IGNITION SWITCH
TURN IGNITION ON. IGNITION SWITCH ABOVE 10.0 VOLTS? OUTPUT CIRCUIT FOR
OUTPUT CKT. AN OPEN OR SHORT
FIG.1 TO GROUND.*
YES
USING A VOLTMETER,
MEASURE THE VSS IS THE VOLTAGE NO CONTINUE TEST
SIGNAL CIRCUIT. BETWEEN TC-91A ON THE
4.0 AND 6.0 VOLTS? NEXT PAGE.
FIG.1
YES
KEY OFF. USING AN OHMMETER,
MEASURE RESISTANCE IS THE RESISTANCE NO REPAIR THE OPEN
DISCONNECT THE ECM OF SENSOR GROUND CKT BELOW 5.0 OHMS? SENSOR GROUND
HARNESS BETWEEN ECM AND VSS. CIRCUIT.*
CONNECTORS.** FIG.2
YES
PERFORM TEST
TC-91B.
T
R
O
U
B
L
E
C
O
D
E
T
E
S
T
S
273
ProCarManuals.com

TEST TC-91ACONTINUED - REPAIRING - VEHICLE SPEED SENSOR TROUBLE CODES
*Perform Verification TEST VER-2A. **Check connectors - Clean / repair as necessary.
TEST TC-91A KEY OFF.
CONTINUED FROM
THE PREVIOUS DISCONNECT THE BCM
PAGE. "B" HARNESS
CONNECTOR.**
USING A VOLTMETER,
MEASURE THE VSS IS THE VOLTAGE YES REPLACE THE BODY
TURN IGNITION ON. SIGNAL CKT. BELOW 5.0 VOLTS? CONTROL MODULE.*
FIG.1
NO
KEY OFF.
REMOVE THE DIESEL
DISCONNECT THE ECM POWER RELAY.*
HARNESS
CONNECTORS.* FIG.2
WITH A JUMPER WIRE, KEY ON. USING A REPAIR THE VSS
CONNECT DIESEL POWER VOLTMETER, MEASURE IS THE VOLTAGE NO SIGNAL CIRCUIT FOR
RELAY CONNECTOR THE VSS SIGNAL CKT. ABOVE 1.0 VOLT? A SHORT TO
CAVITIES 30 AND 87 VOLTAGE.*
(IN PDC). FIG.2 FIG.1
YES
REPLACE THE ENGINE
CONTROL MODULE.*
T
R
O
U
B
L
E
C
O
D
E
T
E
S
T
S
277
ProCarManuals.com

TEST TC-94ACONTINUED - REPAIRING - VEHICLE THEFT ALARM TROUBLE CODES
*Perform Verification TEST VER-2A. **Check connectors - Clean / repair as necessary.
TEST TC-94A
CONTINUED FROM
THE PREVIOUS TURN IGNITION OFF.
PAGE.
DISCONNECT THE
DISCONNECT THE ECM BODY CONTROL
HARNESS MODULE HARNESS
CONNECTORS.** CONNECTORS.**
USING AN OHMMETER, BETWEEN THE BCM
MEASURE RESISTANCE AND THE ECM. IS THE RESISTANCE YES REPAIR THE OPEN
OF THE IMMOBILIZER ABOVE 5.0 OHMS? IMMOBILIZER SIGNAL
SIGNAL CIRCUIT... CIRCUIT.*
FIG.1
NO
ENGINE CONTROL REPAIR THE
MEASURE RESISTANCE MODULE HARNESS IS THE RESISTANCE YES IMMOBILIZER SIGNAL
BETWEEN THE ... CONNECTOR CAVITY BELOW 5.0 OHMS? CIRCUIT FOR A
38 AND GROUND. SHORT TO GROUND.*
NO
WITH A JUMPER WIRE,
REMOVE THE DIESEL CONNECT DIESEL POWER
POWER RELAY.** RELAY CONN. CAVITIES
30 AND 87 (IN PDC).
FIG.2
USING A VOLTMETER, REPAIR THE
MEASURE ECM IS THE VOLTAGE YES IMMOBILIZER SIGNAL
TURN IGNITION ON. HARNESS CONNECTOR ABOVE 1.0 VOLT? CIRCUIT FOR A
CAVITY 38. SHORT TO VOLTAGE.*
FIG.1
NO
CONTINUE TEST
TC-94A ON THE
NEXT PAGE.
T
R
O
U
B
L
E
C
O
D
E
T
E
S
T
S
283
ProCarManuals.com

TEST TC-94ACONTINUED - REPAIRING - VEHICLE THEFT ALARM TROUBLE CODES
*Perform Verification TEST VER-2A. **Check connectors - Clean / repair as necessary.
TEST TC-94A TURN IGNITION OFF. RECONNECT ONLY THE
CONTINUED FROM ENGINE CONTROL
THE PREVIOUS INSTALL THE DIESEL MODULE HARNESS
PAGE. POWER RELAY. CONNECTORS.
KEY ON. MEASURE
USE AN AMMETER IN AMPERAGE FROM BCM IS THE AMPERAGE NO REPLACE THE ENGINE
THE FOLLOWING HARNESS CONNECTOR BETWEEN 1.0 AND CONTROL MODULE.*
STEP. CAVITY 72 TO GROUND. 1.4 MA?
FIG.1
YES
KEY ON. USING THE DRB
OSCILLOSCOPE
RECONNECT THE BODY FUNCTION, SELECT
CONTROL MODULE "LAB SCOPE".
HARNESS CONNECTORS.
SET VOLTAGE RANGE SET TIME RANGE TO
TO +20.0V. SET 0.1S/DIV.
PROBE TO X10.
FIG.2 FIG.3
KEY ON. USING NOTE: A VALID
OSCILLOSCOPE LEAD, IMMOBILIZER SIGNAL
BACKPROBE ECM WILL CYCLE HI AND
HARNESS CONNECTOR LO SIMILAR...
CAVITY 38. FIG. 1
DOES THE DRB
TO THE PATTERN DISPLAY SHOW THE YES REPLACE THE ENGINE
SHOWN IF FIGURE 3. 12 VOLT CONTROL MODULE.*
IMMOBILIZER SIGNAL
CYCLING HI AND LO?
NO
REPLACE THE BODY
CONTROL MODULE.*
T
R
O
U
B
L
E
C
O
D
E
T
E
S
T
S
285
ProCarManuals.com

TEST SC-3ACONTINUED - CHECKING SPEED CONTROL OPERATION
*Perform Verification TEST VER-3A. **Check connectors - Clean / repair as necessary.
TEST SC-3A KEY OFF.
CONTINUED FROM
THE PREVIOUS DISCONNECT THE BRAKE
PAGE. LAMP SWITCH HARNESS
CONNECTOR.**
USING A VOLTMETER, REPAIR THE BRAKE
PROBE BRAKE LAMP IS THE VOLTAGE NO LAMP SWITCH FUSED
SWITCH HARNESS ABOVE 9.0 VOLTS? BATTERY SUPPLY
CONNECTOR CAVITY 6. CIRCUIT FOR AN
FIG.1 OPEN.*
YES
CONNECT A JUMPER DOES THE DRB
BETWEEN BRAKE LAMP DISPLAY CHANGE YES ADJUST OR REPLACE
SWITCH HARNESS TURN IGNITION ON. FROM "RELEASED" TO THE BRAKE LAMP
CONNECTOR CAVITIES "PRESSED"? SWITCH.*
5 AND 6. FIG.1
NO
REMOVE THE JUMPER. AT THE BRAKE LAMP REPAIR THE PRIMARY
USING A VOLTMETER, SWITCH HARNESS IS THE VOLTAGE NO BRAKE SWITCH
MEASURE THE CONNECTOR CAVITY 5. BELOW 1.0 VOLT? SIGNAL CIRCUIT FOR
PRIMARY SWITCH A SHORT TO
SIGNAL CIRCUIT... FIG.1 VOLTAGE.*
YES
KEY OFF. USING AN OHMMETER, REPAIR THE PRIMARY
MEASURE RESISTANCE IS THE RESISTANCE NO BRAKE SWITCH
DISCONNECT THE ECM OF THE PRIMARY BRAKE BELOW 5.0 OHMS? SIGNAL CIRCUIT FOR
HARNESS SW SIGNAL CKT. AN OPEN.*
CONNECTORS.** FIG.2
YES
REPLACE THE ENGINE
CONTROL MODULE.*
S
P
E
E
D
C
O
N
T
R
O
L
T
E
S
T
S
381
ProCarManuals.com

TEST SC-3BCONTINUED - CHECKING SPEED CONTROL OPERATION
*Perform Verification TEST VER-3A. **Check connectors - Clean / repair as necessary.
TEST SC-3B
CONTINUED FROM DISCONNECT THE ECM
THE PREVIOUS TURN IGNITION OFF. HARNESS
PAGE. CONNECTORS.**
OF THE SECONDARY REPAIR OPEN IN THE
USING AN OHMMETER, BRAKE LAMP SWITCH IS THE RESISTANCE NO SECONDARY BRAKE
MEASURE THE SIGNAL CIRCUIT. BELOW 5.0 OHMS? LAMP SWITCH SIGNAL
RESISTANCE...CIRCUIT.*
FIG.1
YES
THE BRAKE LAMP REPAIR SHORT TO
USING AN OHMMETER, SWITCH CONNECTOR IS THE RESISTANCE YES GROUND IN THE
MEASURE RESISTANCE CAVITY 1 AND GROUND. BELOW 5.0 OHMS? SECONDARY BRAKE
BETWEEN... LAMP SWITCH SIGNAL
FIG.2 CIRCUIT.*
NO
REPLACE THE ENGINE
CONTROL MODULE.*
S
P
E
E
D
C
O
N
T
R
O
L
T
E
S
T
S
385
ProCarManuals.com

TEST NS-3BREPAIRING - NO START
Perform TEST NS-3A Before Proceeding
*Perform Verification TEST VER-1A. **Check connectors - Clean / repair as necessary.
START TEST
NS-3B. TURN IGNITION OFF.
DISCONNECT THE
DISCONNECT THE ECM BODY CONTROL
HARNESS MODULE HARNESS
CONNECTORS.** CONNECTORS.**
USING AN OHMMETER,
MEASURE RESISTANCE IS THE RESISTANCE YES REPAIR THE OPEN
OF THE IMMOBILIZER ABOVE 5.0 OHMS? IMMOBILIZER SIGNAL
SIGNAL CIRCUIT. CIRCUIT.*
FIG.1
NO
ENGINE CONTROL REPAIR THE
MEASURE RESISTANCE MODULE HARNESS IS THE RESISTANCE YES IMMOBILIZER SIGNAL
BETWEEN ... CONNECTOR CAVITY BELOW 5.0 OHMS? CIRCUIT FOR A
38 AND GROUND. SHORT TO GROUND.*
FIG. 1
NO
USING A VOLTMETER, REPAIR THE
MEASURE VOLTAGE AT IS THE VOLTAGE YES IMMOBILIZER SIGNAL
TURN IGNITION ON. ECM HARNESS ABOVE 1.0 VOLT? CIRCUIT FOR A
CONNECTOR CAVITY 38. SHORT TO VOLTAGE.*
FIG. 1
NO
CONTINUE TEST
NS-3B ON THE
NEXT PAGE.
N
O
S
T
A
R
T
T
E
S
T
S
415
ProCarManuals.com

TEST NS-3BCONTINUED - REPAIRING - NO START
*Perform Verification TEST VER-1A. **Check connectors - Clean / repair as necessary.
TEST NS-3B TURN IGNITION OFF.
CONTINUED FROM RECONNECT THE
THE PREVIOUS ENGINE CONTROL
PAGE. MODULE HARNESS
CONNECTORS.
KEY ON. MEASURE
USE AN AMMETER IN AMPERAGE FROM BCM IS THE AMPERAGE NO REPLACE THE ENGINE
THE FOLLOWING HARNESS CONNECTOR BETWEEN 1.0 AND CONTROL MODULE.*
STEP. CAVITY 72 TO GROUND. 1.4 MA?
FIG.1
YES
RECONNECT THE BODY USING THE DRB
CONTROL MODULE OSCILLOSCOPE
HARNESS FUNCTION, SELECT
CONNECTORS. "LAB SCOPE".
SET VOLTAGE RANGE TO KEY ON. USING
+20.0V. SET TIME OSCILLOSCOPE LEAD,
RANGE TO 0.1S/DIV. BACKPROBE ECM
SET PROBE TO X10. HARNESS CONNECTOR
FIG.2 CAVITY 38. FIG.1
NOTE: AN IMMOBILIZER DOES THE DRB DISPLAY
SIGNAL WILL CYCLE HI SHOW THE 12 VOLT YES REPLACE THE ENGINE
TO LO SIMILAR TO THE IMMOBILIZER SIGNAL CONTROL MODULE.*
PATTERN SHOWN IN CYCLING HI AND LO?
FIG.2 FIG.2
NO
REPLACE THE BODY
CONTROL MODULE.*
N
O
S
T
A
R
T
T
E
S
T
S
417
ProCarManuals.com