air conditioning CHRYSLER CARAVAN 2003 Service Manual

(19) Install plugs in, or tape over the opened suc-
tion line fittings.
(20) Lower the vehicle.
(21) Remove the suction line from the engine com-
partment.
INSTALLATION
The front air conditioner suction line includes the
low side service port on a section of tubing located
near the compressor. On models equipped with the
optional rear air conditioner, the front air conditioner
suction line also includes a suction line hose and
tube extension that connects the front suction line to
the suction line for the rear air conditioner.
WARNING: REFER TO THE APPLICABLE WARN-
INGS AND CAUTIONS FOR THIS SYSTEM BEFORE
PERFORMING THE FOLLOWING OPERATION.
(Refer to 24 - HEATING & AIR CONDITIONING/
PLUMBING - FRONT - WARNING - A/C PLUMBING)
and (Refer to 24 - HEATING & AIR CONDITIONING/
PLUMBING - FRONT - CAUTION - A/C PLUMBING).
(1) Position the suction line into the engine com-
partment.
(2) Remove the tape or plugs from the suction line
and liquid line fittings and both expansion valve
ports.
(3) Lubricate new rubber O-ring seals with clean
refrigerant oil and install them on the suction line
and liquid line fittings.
(4) Reconnect the liquid line and suction line fit-
tings to the expansion valve.
(5) Install and tighten the nut that secures the
suction line and liquid line fittings to the expansion
valve. Tighten the nut to 23 N´m (17 ft. lbs.).
(6) Engage the retainer that secures the suction
line routing clip to the filter-drier mounting bracket
on the side of the right front strut tower in the
engine compartment.
(7) Remove the tape or plugs from the compressor
suction port and the suction line fitting.
(8) Lubricate a new rubber O-ring seal with clean
refrigerant oil and install it on the suction line fit-
ting.
(9) Reconnect the suction line fitting to the com-
pressor suction port.
(10) Install and tighten the nut that secures the
suction line fitting to the compressor. Tighten the nut
to 23 N´m (17 ft. lbs.).
(11) Reconnect the drain tube to the wiper module
drain on the right side of the engine compartment.
(12) Reinstall the air cleaner top cover and snorkel
onto the air cleaner housing located on the right side
of the engine compartment.
(13) Reconnect the battery negative cable.
(14) If the vehicle is equipped with the optional
rear air conditioner, go to Step 15. If the vehicle does
not have the optional rear air conditioner, go to Step
21.
(15) Raise and support the vehicle.
Fig. 7 Suction Line
1 - EXPANSION VALVE
2 - SUCTION LINE EXTENSION (REAR A/C ONLY)
3 - NUT
4 - ROUTING CLIP (If Equipped)
5 - SUCTION LINE
Fig. 8 Underbody Connections
1 - SUCTION LINE EXTENSION
2 - LIQUID LINE EXTENSION
3 - TIE STRAP
4- HEATER LINE EXTENSIONS
5 - UNDERBODY LINES
24 - 102 PLUMBING - REARRS
SUCTION LINE (Continued)
ProCarManuals.com

(16) Remove the tape or plugs from the suction
line extension fitting and the underbody suction line
fitting (Fig. 35).
(17) Lubricate a new rubber O-ring seal with clean
refrigerant oil and install it on the underbody suction
line fitting.
(18) Reconnect the suction line extension fitting to
the underbody suction line fitting. Tighten the fit-
tings to 23 N´m (17 ft. lbs.).
(19) Install a new tie strap just forward of the con-
nections between the underbody plumbing and the
engine compartment plumbing for the rear heater
and air conditioner.
(20) Lower the vehicle.
(21) Evacuate the refrigerant system. (Refer to 24
- HEATING & AIR CONDITIONING/PLUMBING -
FRONT/REFRIGERANT - STANDARD PROCE-
DURE - REFRIGERANT SYSTEM EVACUATE).
(22) Charge the refrigerant system. (Refer to 24 -
HEATING & AIR CONDITIONING/PLUMBING -
FRONT/REFRIGERANT - STANDARD PROCE-
DURE - REFRIGERANT SYSTEM CHARGE).UNDERBODY LINES
DESCRIPTION
The rear heater-A/C unit plumbing is used only on
models with the optional rear heater-A/C unit. The
formed metal rear heater-A/C unit suction line, liquid
line, and heater lines are available for separate ser-
vice replacement. The molded and straight heater
hoses used on the rear heater-A/C unit can be ser-
viced in the vehicle. Refer to Group 7 - Cooling Sys-
tem for the heater hose service procedures.
OPERATION
The rear heater and A/C lines are all serviced as
individual pieces. When disconnecting any line or
block ensure that the area around it is clean of any
contaminations that can get in to the system (Fig. 9),
(Fig. 10), (Fig. 12), (Fig. 11) and (Fig. 13).
Any kinks or sharp bends in the rear heater-A/C
unit plumbing will reduce the capacity of the entire
heating and air conditioning system. Kinks and
sharp bends reduce the system flow. High pressures
are produced in the refrigerant system when the air
conditioning compressor is operating. High tempera-
ture coolant is present in the heater plumbing when
the engine is operating. Extreme care must be exer-
cised to make sure that each of the plumbing connec-
tions is pressure-tight and leak free.
Fig. 9 Rear Heater and A/C Lines
1 - HEATER CONNECTION
2 - REAR A/C LINE BLOCK CONNECTION
RSPLUMBING - REAR24 - 103
SUCTION LINE (Continued)
ProCarManuals.com

REMOVAL
REMOVAL - REAR HEATER LINES
(1) Raise and support vehicle.
(2) Pinch off rubber heater line hose.
(3) Disconnect quick connect fitting at C-pillar.
(4) Loosen one screw and remove the other screw
at each of the three brackets holding the front of the
line to the underbody.
(5) Lower rear of line and drain coolant into a
suitable container.
(6) Loosen hose clamps at front of line and remove
line from vehicle.
REMOVAL - REAR AIR CONDITIONING LINES
(1) Recover A/C system.
(2) Hoist and support vehicle.
(3) Loosen one screw and remove the other screw
at each of the three brackets holding the A/C lines to
the underbody (Fig. 9).
(4) Remove both A/C lines from the two rear
retaining clamps, behind rear wheel.
(5) Remove both compression fittings at front of
A/C lines (Fig. 10).
(6) Remove (1) bolt securing A/C lines to block
located at A/C housing, behind rear wheel, and sepa-
rate block (Fig. 13).
(7) Remove rear wheel.
(8) Separate ABS harness from flex hose clamps.
(9) Remove heater lines from underbody brackets.
(10) Pinch off rubber heater line hoses at front of
vehicle.
Fig. 10 Front Lines Connected to Rear Lines
Fig. 11 Rear Heater Hose Connection
1 - REAR HEATER HOSE
Fig. 12 Rear heater hose quick connects
1 - INSERT
2 - QUICK CONNECT
3 - COMPRESS INSERT FOR REMOVAL
Fig. 13 Rear A/C Block Connection
1 - CLEAN AREA AROUND BLOCK BEFORE REMOVAL
24 - 104 PLUMBING - REARRS
UNDERBODY LINES (Continued)
ProCarManuals.com

(11) Loosen hose clamps at front of heater lines
and allow them to hang from vehicle.
(12) Remove rear A/C lines from vehicle.
(13) Remove nylon wedge holding lines into rear
block (Fig. 14).INSTALLATION
INSTALLATION - REAR HEATER LINES
(1) Install line into underbody straps.
(2) Install line into front hose and install hose
clamp.
(3) Connect quick fitting at rear of line.
(4) Lower vehicle.
(5) Fill cooling system (Refer to 7 - COOLING -
STANDARD PROCEDURE).
INSTALLATION - REAR AIR CONDITIONING
LINES
(1) Before installation, replace all O-rings and gas-
kets. Coat all sealing surfaces with approved wax-
free refrigerant oil.
(2) Install A/C line into rear block with nylon
wedge.
(3) Install A/C lines into five underbody brackets.
(4) Connect forward compression fittings.
(5) Install bolt at sealing block to rear A/C hous-
ing.
(6) Install ABS harness into clips.
(7) Install heater hoses into underbody brackets.
(8) Install lines into front hoses and install hose
clamps.
(9) Lower vehicle.
(10) Evacuate and recharge system.
(11) Fill cooling system (Refer to 7 - COOLING -
STANDARD PROCEDURE).
Fig. 14 UNDERBODY LINE WEDGES
1 - O-RING
2 - DISCHARGE LINE
3 - NYLON WEDGE
4 - SEALING BLOCK
5 - VISE
6 - SUCTION LINE
RSPLUMBING - REAR24 - 105
UNDERBODY LINES (Continued)
ProCarManuals.com

CONDITIONING/CABIN HEATER/FUEL LINE -
INSTALLATION).
(4) Connect the electrical connector to the fuel
pump by depressing the integral spring and pushing
the connector towards the dosing pump. Pull the con-
nector towards the heater to verify the installation.
(5) Verify function of the heater.
FUEL LINE
STANDARD PROCEDURE - CLEANING
(1) Remove the cabin heater fuel line(Refer to 24 -
HEATING & AIR CONDITIONING/CABIN HEAT-
ER/FUEL LINE - REMOVAL).
(2) With cabin heater line removed from vehicle
place a shop cloth on the fuel tank end of the fuel
line to catch any residue, then apply a small amount
of air pressure to the other end of the fuel line.
(3) Check to see if air pressure is coming from the
tank end of the line. If pressure is flowing unre-
stricted the line is clean.
(4) If the line shows any signs of being restricted
after air pressure is applied, then the fuel line should
be replaced.(5) Install the cabin heater line(Refer to 24 -
HEATING & AIR CONDITIONING/CABIN HEAT-
ER/FUEL LINE - INSTALLATION).
(6) Verify function of the heater.
REMOVAL
(1) Elevate vehicle on a lift taking note of the
heater exhaust tube flexible section.
(2) Remove clamps on dosing pump end of fuel line
and separate line from pump (Fig. 3).
NOTE: Have an approved fuel holding device ready
to capture any diesel fuel that drains from fuel line
or heater unit.
(3) Remove clamp from fuel line at fuel tank con-
nection and separate line from tank.
(4) Remove any retaining clips and remove line
from vehicle.
Fig. 2 Dosing Pump Fuel Line
1 - Fuel Line
2 - Retaining Clamps3 - Dosing Pump
4 - Heater Unit Air Intake Pipe
RSDIESEL SUPPLEMENTAL HEATER - DCHA - EXPORT24 - 109
FUEL DOSING PUMP (Continued)
ProCarManuals.com

NOTE: Do not activate the Dosing Pump Prime
more than one time. This will put excess fuel in the
DCHA Heater Module an cause smoke to emit from
the DCHA exhaust pipe when heater activation
occurs.
NOTE: A clicking noise heard coming from the Dos-
ing Pump indicates that the pump is operational.
(7) With the DRBIIItin Cabin Heater, select Sys-
tem Tests and Dosing Pump Prime. Allow the Dosing
Pump to run for the full 45 second cycle time. When
the 45 second cycle is complete, press Page Back on
the DRBIIItkey pad to exit the Dosing Pump Prime.
The Dosing Pump priming procedure is now com-
plete.
HEATER UNIT
REMOVAL
WARNING: ALLOW THE DCHA TO COOL BEFORE
PERFORMING A COMPONENT INSPECTION/REPAIR
OR REPLACEMENT. FAILURE TO FOLLOW THESE
INSTRUCTIONS MAY RESULT IN PERSONAL
INJURY.
WARNING: ALLOW THE EXHAUST SYSTEM TO
COOL BEFORE PERFORMING A COMPONENT
INSPECTION/REPAIR OR REPLACEMENT. FAILURE
TO FOLLOW THESE INSTRUCTION MAY RESULT IN
PERSONAL INJURY.
(1) Elevate the vehicle on a hoist/lift taking note of
heater exhaust tube flexible section.
(2) Drain cooling system(Refer to 7 - COOLING -
STANDARD PROCEDURE).
(3) Carefully open one hose to the underbody tube
assembly and drain the remaining coolant. A salvage
hose is a good idea to control the residual coolant, as
flow will occur from both the heater and the hose and
tube assemblies.
(4) Remove the second hose from the underbody
hose and tube assembly.
(5) Loosen the hose and tube assembly from the
toe-board cross member at two locations.
(6) Disconnect the electrical connector from the
body harness near the toe board cross member and
rail.
(7) Remove the wiring harness from the toe board
cross member(Refer to 24 - HEATING & AIR CON-
DITIONING/CABIN HEATER/HEATER UNIT -
REMOVAL).
(8) Open the fuel fill cap. Disconnect the rubber
fuel hose between the body tube assembly and thefuel pump nipple at the body tube joint. A minimal
amount of fuel may flow from the open port.
NOTE: Utilize an approved fuel storage container to
catch any residual fuel.
(9) Loosen the two M8 fasteners at the rail. Take
care to notice that the exhaust tube bracket tab is on
top of the heater bracket and that there are (2)
spacer washers installed between the rubber grom-
mets.
(10) Remove the heater exhaust tube flex section
from the exhaust tube by loosening the M6 bolt of
the clamp assembly. Remove the hose from the
exhaust tube. Removal of the rail tube assembly may
aid in this service operation.(Refer to 24 - HEATING
& AIR CONDITIONING/CABIN HEATER/EXHAUST
TUBE - REMOVAL).
(11) Remove seat hex nut at the heater mounting
flange to cross member.
(12) Loosen the remaining M6 and M8 fasteners
which mount the exhaust tube assembly to the vehi-
cle.
(a) Install a suitable cabin heater support device
under the cabin heater and secure the cabin heater
to the device.
(13) Loosen the remaining three M6 fasteners to
the cross members.
(14) Remove the loosened fasteners that support
the heater while supporting the weight of the heater.
(15) Swing the unit mounting bracket from
between the exhaust bracket and rail mounting loca-
tion. Drain any residual coolant from the heater unit.
(16) Lower the cabin heater and remove from the
supporting device and place on a suitable work area.
INSTALLATION
(1) Install the unit mounting bracket between the
exhaust bracket and the rail mounting location.
(2) Install the fasteners that support the heater
while supporting the weight of the heater.
(3) Install the three M6 fasteners to the cross
members. Tighten the M6 fasteners to 7 Nm (5 ft.
lbs.).
(4) Position the two spacer washers between the
body and the rubber grommets for the two M8
mounting points on the rail.
(5) Tighten the remaining M6 fasteners to 7 Nm (5
ft. lbs.) and the M8 fasteners to 23 Nm (17 ft. lbs.)
which mount the exhaust tube assembly to the vehi-
cle.
(6) Install the seat hex nut at the heater mounting
flange to the cross members. Tighten to 60 Nm (44 ft.
lbs.)
(7) Install the heater exhaust tube flex section to
the exhaust tube by tightening the M6 bolt of the
clamp assembly. Install the hose to the exhaust tube.
RSDIESEL SUPPLEMENTAL HEATER - DCHA - EXPORT24 - 111
FUEL LINE (Continued)
ProCarManuals.com

(8) Tighten the two M8 fasteners at the rail to 23
Nm (17 ft. lbs.). Taking care so that the exhaust tube
bracket tab is on the top of the heater bracket.
(9) Install the wiring harness(Refer to 24 - HEAT-
ING & AIR CONDITIONING/CABIN HEATER/
HEATER UNIT - INSTALLATION).
(10) Tighten the hose and tube assembly to the
toe-board cross member at two locations.
(11) Install the second hose to the underbody hose
and tube assembly.
(12) Connect the rubber fuel hose between the
body tube assembly and the fuel pump nipple at the
body tube joint. Close the fuel fill cap.
(13) Remove the heater unit support device from
under the vehicle.
(14) Lower vehicle from lift.
(15) Refill cooling system(Refer to 7 - COOLING -
STANDARD PROCEDURE).
(16) Verify function of the cabin heater.
SUPPLEMENTAL DIESEL
HEATER WIRING
REMOVAL
(1) Elevate vehicle on a lift taking note of the
exhaust tube flexible section.
(2) Unplug connector from vehicle wiring harness
to cabin heater harness.
(3) Unplug connector from cabin heater harness to
dosing pump connector.
(4) Unplug two connectors from cabin heater har-
ness to cabin heater controller connectors.
(5) Remove two wiring harness connectors from
underbody.
(6) Remove two wiring harness connectors from
cabin heater shield.
(7) Carefully route the cabin heater harness to the
left side between the cabin heater unit and the cabin
heater shield.
INSTALLATION
(1) Carefully route the cabin heater harness from
the left side of the cabin heater between the cabin
heater unit and the cabin heater shield.
(2) Install the two wiring harness retaining con-
nectors to the cabin heater shield.
(3) Route the wiring harness along the underside
of the vehicle and install the two wiring harness
retaining connectors.
(4) Plug the two connectors from the cabin heater
harness to the cabin heater controller.
(5) Plug the connector to the cabin heater harness
to the dosing pump connector.
(6) Plug the connector from the vehicle wiring har-
ness to the cabin heater harness.(7) Lower the vehicle.
(8) Verify function of the cabin heater.
AIR INTAKE PIPE
REMOVAL
NOTE: Heater air intake tube is part of an assembly
that includes the heater cooling intake and return
pipes. If heater air intake tube requires removal or
replacement the entire assembly will require remov-
al/replacement.
(1) Drain cooling system(Refer to 7 - COOLING -
STANDARD PROCEDURE).
(2) Remove clamps from the heater tubes at the
lower heater port and the lower EGR connector
which are located under the hood.
(3) Remove the retaining clamp at the heater air
intake muffler connection(Refer to 24 - HEATING &
AIR CONDITIONING/CABIN HEATER/INLET
MUFFLER - REMOVAL).
(4) Remove the clamp at the flexible tube to steel
tube connection (Fig. 4).
Fig. 4 FLEXIBLE AIR INTAKE LINE
1 - HEATER UNIT AND SPLASH SHIELD
2 - DOSING PUMP
3 - DOSING PUMP FUEL LINE
4 - FLEXIBLE INTAKE LINE
5 - CLAMP
6 - STEEL INTAKE PIPE
24 - 112 DIESEL SUPPLEMENTAL HEATER - DCHA - EXPORTRS
HEATER UNIT (Continued)
ProCarManuals.com

ABS FASTENER TORQUE,
SPECIFICATIONS......................5-79
ABSORBER - DESCRIPTION, SHOCK.......2-36
ABSORBER - INSTALLATION, SHOCK......2-38
ABSORBER - OPERATION, SHOCK........2-36
ABSORBER - REMOVAL, SHOCK..........2-36
ABSORBER (UPPER BUSHING) -
ASSEMBLY, SHOCK....................2-37
ABSORBER (UPPER BUSHING) -
DISASSEMBLY, SHOCK.................2-36
A/C COMPRESSOR - DESCRIPTION......24-63
A/C COMPRESSOR - OPERATION........24-63
A/C COOL DOWN TEST - DIAGNOSIS
AND TESTING........................24-4
A/C DISTRIBUTION DUCT -
INSTALLATION.......................24-53
A/C DISTRIBUTION DUCT - REMOVAL....24-53
A/C HEATER CONTROL - INSTALLATION....24-9
A/C HEATER CONTROL - REMOVAL.......24-9
A/C PERFORMANCE TEST - DIAGNOSIS
AND TESTING........................24-5
A/C PLUMBING - CAUTION.............24-61
A/C PLUMBING - WARNING............24-61
A/C PRESSURE TRANSDUCER -
DESCRIPTION.......................24-10
A/C PRESSURE TRANSDUCER -
DIAGNOSIS AND TESTING.............24-10
A/C PRESSURE TRANSDUCER -
INSTALLATION.......................24-11
A/C PRESSURE TRANSDUCER -
OPERATION.........................24-10
A/C PRESSURE TRANSDUCER -
REMOVAL..........................24-10
ACCELERATOR PEDAL - INSTALLATION . . . 14-24
ACCELERATOR PEDAL - REMOVAL.......14-23
ACCESSORY DRIVE BELT - DIAGNOSIS
AND TESTING.........................7-7
ACCESSORY DRIVE BELT TENSION,
SPECIFICATIONS.......................7-5
ACCESSORY RELAY - DESCRIPTION . . . 8W-97-2
ACCESSORY RELAY - DIAGNOSIS &
TESTING.........................8W-97-2
ACCESSORY RELAY - OPERATION.....8W-97-2
ACCUMULATOR - DESCRIPTION........21-188
ACCUMULATOR - OPERATION..........21-189
A/C-HEATER CONTROL - INSTALLATION . . . 24-29
A/C-HEATER CONTROL - REMOVAL......24-29
ACTUATOR - DESCRIPTION, BLEND
DOOR........................24-11,24-30
ACTUATOR - DESCRIPTION, ENGAGE.....8N-10
ACTUATOR - DESCRIPTION, LATCH......8N-14
ACTUATOR - DESCRIPTION, MODE
DOOR.............................24-24
ACTUATOR - DESCRIPTION,
RECIRCULATION DOOR................24-27
ACTUATOR - INSTALLATION, BLEND
DOOR........................24-12,24-31
ACTUATOR - INSTALLATION, ENGAGE....8N-11
ACTUATOR - INSTALLATION, LATCH.....8N-14
ACTUATOR - INSTALLATION, MODE
DOOR........................24-25,24-36
ACTUATOR - INSTALLATION,
RECIRCULATION DOOR................24-28
ACTUATOR - OPERATION, BLEND DOOR . . 24-11,
24-30
ACTUATOR - OPERATION, ENGAGE......8N-11
ACTUATOR - OPERATION, LATCH........8N-14
ACTUATOR - OPERATION, MODE DOOR . . . 24-24
ACTUATOR - OPERATION,
RECIRCULATION DOOR................24-27
ACTUATOR - REMOVAL, BLEND DOOR . . . 24-12,
24-31
ACTUATOR - REMOVAL, ENGAGE........8N-11
ACTUATOR - REMOVAL, LATCH.........8N-14
ACTUATOR - REMOVAL, MODE DOOR....24-25,
24-36
ACTUATOR - REMOVAL, RECIRCULATION
DOOR.............................24-27
ADAPTER - INSTALLATION, FRONT DISC
BRAKE CALIPER......................5-31
ADAPTER - INSTALLATION, OIL FILTER
. . . 9-139
ADAPTER - REMOVAL, FRONT DISC
BRAKE CALIPER
......................5-31
ADAPTER - REMOVAL, OIL FILTER
.......9-139
ADAPTIVE MEMORIES, OPERATION -
FUEL CORRECTION OR
................14-20
ADDING ADDITIONAL COOLANT -
STANDARD PROCEDURE
.................7-5ADDITIONAL COOLANT - STANDARD
PROCEDURE, ADDING...................7-5
ADHESIVE ATTACHED - INSTALLATION,
EXTERIOR NAME PLATES..............23-50
ADHESIVE ATTACHED - REMOVAL,
EXTERIOR NAME PLATES..............23-50
ADHESIVE LOCATIONS -
SPECIFICATIONS, STRUCTURAL........23-153
ADJUSTER-BORC-PILLAR -
INSTALLATION, SEAT BELT HEIGHT......8O-12
ADJUSTER-BORC-PILLAR -
REMOVAL, SEAT BELT HEIGHT..........8O-12
ADJUSTER - DIAGNOSIS AND TESTING,
DRUM BRAKE AUTOMATIC..............5-13
ADJUSTER - INSTALLATION, FRONT
SEAT TRACK MANUAL................23-94
ADJUSTER - INSTALLATION, FRONT
SEAT TRACK POWER.................23-94
ADJUSTER - REMOVAL, FRONT SEAT
TRACK MANUAL.....................23-94
ADJUSTER - REMOVAL, FRONT SEAT
TRACK POWER......................23-94
ADJUSTER KNOB - INSTALLATION, SEAT
BELT HEIGHT.......................8O-13
ADJUSTER KNOB - REMOVAL, SEAT
BELT HEIGHT.......................8O-13
ADJUSTER NOISE DIAGNOSIS -
DIAGNOSIS AND TESTING, HYDRAULIC
LASH...............................9-34
ADJUSTER TENSION RELEASE -
STANDARD PROCEDURE, PARKING
BRAKE AUTOMATIC....................5-58
ADJUSTER TENSION RESET -
STANDARD PROCEDURE, PARKING
BRAKE AUTOMATIC.....................5-59
ADJUSTERS - INSTALLATION,
HYDRAULIC LASH.....................9-34
ADJUSTERS - REMOVAL, HYDRAULIC
LASH...............................9-34
AERATION - DIAGNOSIS AND TESTING,
COOLING SYSTEM.....................7-3
AFTER AN AIRBAG DEPLOYMENT -
STANDARD PROCEDURE, SERVICE.......8O-3
AIR CLEANER ELEMENT - INSTALLATION . . 9-24,
9-98
AIR CLEANER ELEMENT - REMOVAL . . 9-24,9-98
AIR CLEANER HOUSING - INSTALLATION . . 9-24,
9-99
AIR CLEANER HOUSING - REMOVAL . . 9-24,9-99
AIR CONDITIONING LINES -
INSTALLATION, REAR................24-105
AIR CONDITIONING LINES - REMOVAL,
REAR.............................24-104
AIR CONTROL MOTOR - DESCRIPTION,
IDLE...............................14-28
AIR CONTROL MOTOR - INSTALLATION,
IDLE...............................14-29
AIR CONTROL MOTOR - OPERATION,
IDLE...............................14-28
AIR CONTROL MOTOR - REMOVAL, IDLE . . 14-29
AIR EXHAUSTER - DESCRIPTION, REAR
QUARTER PANEL/FENDER..............23-56
AIR EXHAUSTER - INSTALLATION, REAR
QUARTER PANEL/FENDER..............23-57
AIR EXHAUSTER - REMOVAL, REAR
QUARTER PANEL/FENDER..............23-56
AIR FILTER - DESCRIPTION............24-39
AIR FILTER - INSTALLATION............24-40
AIR FILTER - REMOVAL...............24-39
AIR GAP - STANDARD PROCEDURE,
COMPRESSOR CLUTCH...............24-17
AIR GAP, SPECIFICATIONS - WHEEL
SPEED SENSOR.......................5-79
AIR INTAKE PIPE - INSTALLATION......24-113
AIR INTAKE PIPE - REMOVAL..........24-112
AIR OUTLETS - DESCRIPTION.....24-40,24-52
AIR OUTLETS - INSTALLATION..........24-52
AIR OUTLETS - REMOVAL.............24-52
AIR PRESSURE TESTS - DIAGNOSIS
AND TESTING, CLUTCH...............21-122
AIR TEMPERATURE SENSOR -
DESCRIPTION, INLET.................14-29
AIR TEMPERATURE SENSOR -
OPERATION, INLET
...................14-29
AIRBAG - DESCRIPTION, DRIVER
........8O-5
AIRBAG - DESCRIPTION, PASSENGER
.....8O-7
AIRBAG - DESCRIPTION, SEAT
..........8O-10
AIRBAG - INSTALLATION, DRIVER
........8O-6AIRBAG - INSTALLATION, PASSENGER....8O-9
AIRBAG - OPERATION, DRIVER..........8O-5
AIRBAG - OPERATION, PASSENGER.......8O-8
AIRBAG - OPERATION, SEAT...........8O-11
AIRBAG - REMOVAL, DRIVER............8O-5
AIRBAG - REMOVAL, PASSENGER........8O-8
AIRBAG CONTROL MODULE -
DESCRIPTION, SIDE IMPACT...........8O-17
AIRBAG CONTROL MODULE -
INSTALLATION, SIDE IMPACT...........8O-17
AIRBAG CONTROL MODULE -
OPERATION, SIDE IMPACT.............8O-17
AIRBAG CONTROL MODULE - REMOVAL,
SIDE IMPACT.......................8O-17
AIRBAG DEPLOYMENT - STANDARD
PROCEDURE, SERVICE AFTER AN........8O-3
AIRBAG SYSTEM - DIAGNOSIS AND
TESTING............................8O-2
AIRBAG TRIM COVER - INSTALLATION,
DRIVER.............................8O-7
AIRBAG TRIM COVER - REMOVAL,
DRIVER.............................8O-6
AIRBAGS - STANDARD PROCEDURE,
HANDLING..........................8O-3
AJAR SWITCH - EXPORT -
INSTALLATION, HOOD.................8Q-3
AJAR SWITCH - EXPORT - REMOVAL,
HOOD..............................8Q-3
ALIGNMENT - DESCRIPTION, WHEEL......2-46
ALIGNMENT - EXPORT - STANDARD
PROCEDURE, FRONT FOG LAMP UNIT.....8L-9
ALIGNMENT - EXPORT - STANDARD
PROCEDURE, HEADLAMP UNIT.........8L-17
ALIGNMENT - STANDARD PROCEDURE,
FRONT FOG LAMP UNIT................8L-9
ALIGNMENT - STANDARD PROCEDURE,
FRONT WIPER ARM...................8R-8
ALIGNMENT - STANDARD PROCEDURE,
HEADLAMP UNIT.....................8L-17
ALIGNMENT - STANDARD PROCEDURE,
WHEEL.............................2-51
ALIGNMENT, SPECIFICATIONS - WHEEL....2-55
ALUMINUM WHEEL CARE - CLEANING . . . 22-18
AMBIENT TEMP SENSOR - DESCRIPTION . 8M-11
AMBIENT TEMP SENSOR - OPERATION . . 8M-11
AMBIENT TEMPERATURE SENSOR -
DIAGNOSIS AND TESTING.............8M-12
AMBIENT TEMPERATURE SENSOR
CIRCUIT - DIAGNOSIS AND TESTING....8M-12
AN AIRBAG DEPLOYMENT - STANDARD
PROCEDURE, SERVICE AFTER...........8O-3
ANTENNA - EXPORT - DESCRIPTION,
QUARTER GLASS INTEGRAL............8A-9
ANTENNA - EXPORT - DIAGNOSIS AND
TESTING, QUARTER GLASS INTEGRAL....8A-9
ANTENNA - EXPORT - OPERATION,
QUARTER GLASS INTEGRAL............8A-9
ANTENNA BODY AND CABLE -
DESCRIPTION........................8A-4
ANTENNA BODY AND CABLE -
DIAGNOSIS AND TESTING..............8A-4
ANTENNA BODY AND CABLE -
INSTALLATION.......................8A-6
ANTENNA BODY AND CABLE -
OPERATION..........................8A-4
ANTENNA BODY AND CABLE - REMOVAL . . 8A-5
ANTENNA CABLE - INSTALLATION,
INSTRUMENT PANEL..................8A-9
ANTENNA CABLE - REMOVAL,
INSTRUMENT PANEL..................8A-8
ANTENNA MODULE - EXPORT -
DESCRIPTION........................8A-6
ANTENNA MODULE - EXPORT -
DIAGNOSIS AND TESTING..............8A-7
ANTENNA MODULE - EXPORT -
INSTALLATION.......................8A-7
ANTENNA MODULE - EXPORT -
OPERATION..........................8A-6
ANTENNA MODULE - EXPORT -
REMOVAL
...........................8A-7
ANTILOCK BRAKE - DESCRIPTION,
CONTROLLER
........................8E-5
ANTILOCK BRAKE - INSTALLATION,
CONTROLLER
........................8E-6
ANTILOCK BRAKE - OPERATION,
CONTROLLER
........................8E-5
ANTILOCK BRAKE - REMOVAL,
CONTROLLER
........................8E-6
RSINDEX1
Description Group-Page Description Group-Page Description Group-Page
ProCarManuals.com

COLUMN COVER BACKING PLATE -
REMOVAL, STEERING.................23-69
COLUMN TORQUE, SPECIFICATIONS.....19-14
COMBUSTION PRESSURE LEAKAGE
TEST - DIAGNOSIS AND TESTING,
CYLINDER........................9-83,9-9
COMMON PROBLEM CAUSES -
DIAGNOSIS AND TESTING.............21-30
COMMUNICATION RECEIVE - PCM INPUT
- OPERATION, DATA BUS..............8E-15
COMMUNICATIONS INTERFACE (PCI)
BUS, OPERATION - PROGRAMMABLE....14-21
COMPASS CALIBRATION - STANDARD
PROCEDURE.........................8M-3
COMPASS DEMAGNETIZING -
STANDARD PROCEDURE...............8M-4
COMPASS MINI-TRIP COMPUTER -
DIAGNOSIS AND TESTING.............8M-10
COMPASS VARIATION ADJUSTMENT -
STANDARD PROCEDURE...............8M-5
COMPASS/MINI-TRIP COMPUTER -
DESCRIPTION........................8M-9
COMPASS/MINI-TRIP COMPUTER -
INSTALLATION......................8M-10
COMPASS/MINI-TRIP COMPUTER -
OPERATION.........................8M-9
COMPASS/MINI-TRIP COMPUTER -
REMOVAL..........................8M-10
COMPLAINTS - DIAGNOSIS AND
TESTING, CLUTCH CHATTER..............6-6
COMPRESSION PRESSURE TEST -
DIAGNOSIS AND TESTING, CYLINDER . . 9-83,9-9
COMPRESSOR - 2.4/3.3/3.8L ENGINES -
REMOVAL............................24-64
COMPRESSOR - DESCRIPTION, A/C......24-63
COMPRESSOR - INSTALLATION.........24-65
COMPRESSOR - OPERATION, A/C........24-63
COMPRESSOR CLUTCH - DESCRIPTION . . 24-16
COMPRESSOR CLUTCH - OPERATION....24-17
COMPRESSOR CLUTCH AIR GAP -
STANDARD PROCEDURE...............24-17
COMPRESSOR CLUTCH BREAK-IN -
STANDARD PROCEDURE...............24-17
COMPRESSOR CLUTCH COIL -
DIAGNOSIS AND TESTING.............24-20
COMPRESSOR CLUTCH RELAY -
DESCRIPTION.......................24-21
COMPRESSOR CLUTCH RELAY -
DIAGNOSIS AND TESTING.............24-22
COMPRESSOR CLUTCH RELAY -
INSTALLATION.......................24-22
COMPRESSOR CLUTCH RELAY -
OPERATION.........................24-21
COMPRESSOR CLUTCH RELAY -
REMOVAL..........................24-22
COMPRESSOR CLUTCH/COIL -
INSPECTION........................24-18
COMPRESSOR MOUNTING BRACKET -
2.4L ENGINE - INSTALLATION...........24-66
COMPRESSOR MOUNTING BRACKET -
2.4L ENGINE - REMOVAL..............24-65
COMPRESSOR NOISE DIAGNOSIS -
DIAGNOSIS AND TESTING.............24-63
COMPUTER - DESCRIPTION, COMPASS/
MINI-TRIP..........................8M-9
COMPUTER - DIAGNOSIS AND TESTING,
COMPASS MINI-TRIP
.................8M-10
COMPUTER - INSTALLATION, COMPASS/
MINI-TRIP
.........................8M-10
COMPUTER - OPERATION, COMPASS/
MINI-TRIP
..........................8M-9
COMPUTER - REMOVAL, COMPASS/
MINI-TRIP
.........................8M-10
CONCENTRATION TESTING - DIAGNOSIS
AND TESTING, COOLANT
...............7-19
CONDENSER - DESCRIPTION
...........24-66
CONDENSER - INSTALLATION
...........24-67
CONDENSER - OPERATION
.............24-66
CONDENSER - REMOVAL
..............24-66
CONDITION CHECK, STANDARD
PROCEDURE - FLUID LEVEL
...........21-201
CONDITIONING LINES - INSTALLATION,
REAR AIR
.........................24-105
CONDITIONING LINES - REMOVAL, REAR
AIR
..............................24-104
CONNECTING ROD - DESCRIPTION,
PISTON
........................9-116,9-42CONNECTING ROD - INSTALLATION,
PISTON.............................9-44
CONNECTING ROD - REMOVAL, PISTON . . . 9-43
CONNECTING ROD BEARING
CLEARANCE - STANDARD
PROCEDURE, MEASURING.............9-120
CONNECTING ROD, FITTING.............9-45
CONNECTING RODS - STANDARD
PROCEDURE, FITTING.................9-116
CONNECTOR - DESCRIPTION, DATA LINK . . 8E-6
CONNECTOR - INSTALLATION.......8W-01-11
CONNECTOR - OPERATION, DATA LINK....8E-7
CONNECTOR - REMOVAL...........8W-01-11
CONNECTOR, GROUND AND SPLICE
INFORMATION - DESCRIPTION........8W-01-7
CONNECTOR/GROUND/SPLICE LOCATION
- DESCRIPTION....................8W-91-1
CONSOLE - DESCRIPTION, OVERHEAD....8M-1
CONSOLE - DIAGNOSIS AND TESTING,
OVERHEAD..........................8M-2
CONSOLE - INSTALLATION, LOWER......23-68
CONSOLE - OPERATION, OVERHEAD......8M-2
CONSOLE - REMOVAL, LOWER..........23-68
CONSOLE - REMOVAL, OVERHEAD.......8M-6
CONSOLE LAMP SWITCH -
INSTALLATION, CENTER...............8L-26
CONSOLE LAMP SWITCH - REMOVAL,
CENTER............................8L-26
CONSOLE, SPECIAL TOOLS - OVERHEAD . . 8M-6
CONSOLE TRAY - BRACKET ASSEMBLY -
INSTALLATION, FLOOR................23-82
CONSOLE TRAY - BRACKET ASSEMBLY -
REMOVAL, FLOOR....................23-82
CONSOLE TRAY - INSTALLATION, FLOOR . . 23-81
CONSOLE TRAY - REMOVAL, FLOOR.....23-81
CONTAINER - DESCRIPTION, COOLANT
RECOVERY..........................7-19
CONTAINER - INSTALLATION, COOLANT
RECOVERY..........................7-20
CONTAINER - OPERATION, COOLANT
RECOVERY..........................7-19
CONTAINER - REMOVAL, COOLANT
RECOVERY..........................7-20
CONTAMINATION - DIAGNOSIS AND
TESTING, BRAKE FLUID................5-32
CONTINUITY - STANDARD PROCEDURE,
TESTING.........................8W-01-9
CONTROL (4 SPEED EATX ONLY) -
OPERATION, INTERACTIVE SPEED........8P-2
CONTROL ARM - DESCRIPTION, LOWER . . . 2-12
CONTROL ARM - INSPECTION, LOWER....2-14
CONTROL ARM - INSTALLATION, LOWER . . 2-15
CONTROL ARM - OPERATION, LOWER.....2-12
CONTROL ARM - REMOVAL, LOWER......2-12
CONTROL ARM (REAR BUSHING -
HYDRO) - ASSEMBLY, LOWER...........2-14
CONTROL ARM (REAR BUSHING -
HYDRO) - DISASSEMBLY, LOWER........2-14
CONTROL ARM (REAR BUSHING -
STANDARD) - ASSEMBLY, LOWER........2-14
CONTROL ARM (REAR BUSHING -
STANDARD) - DISASSEMBLY, LOWER.....2-13
CONTROL CABLE - INSTALLATION,
THROTTLE..........................14-35
CONTROL CABLE - REMOVAL,
THROTTLE..........................14-35
CONTROL CALIBRATION - STANDARD
PROCEDURE, HEATER-A/C..............24-8
CONTROL CIRCUIT TEST - DIAGNOSIS
AND TESTING.......................8F-30
CONTROL INFORMATION LABEL -
DESCRIPTION, VEHICLE EMISSION.......25-1
CONTROL MODULE - DESCRIPTION,
BODY...............................8E-3
CONTROL MODULE - DESCRIPTION,
FRONT..............................8E-7
CONTROL MODULE - DESCRIPTION,
POWER LIFTGATE....................8E-10
CONTROL MODULE - DESCRIPTION,
SIDE IMPACT AIRBAG
.................8O-17
CONTROL MODULE - DESCRIPTION,
SLIDING DOOR
......................8E-19
CONTROL MODULE - DESCRIPTION,
TRANSMISSION
......................8E-20
CONTROL MODULE - DIAGNOSIS AND
TESTING, FRONT
......................8E-7
CONTROL MODULE - INSTALLATION,
BODY
...............................8E-5CONTROL MODULE - INSTALLATION,
FRONT..............................8E-8
CONTROL MODULE - INSTALLATION,
POWER LIFTGATE....................8E-11
CONTROL MODULE - INSTALLATION,
SIDE IMPACT AIRBAG.................8O-17
CONTROL MODULE - INSTALLATION,
SLIDING DOOR......................8E-20
CONTROL MODULE - OPERATION, BODY . . . 8E-3
CONTROL MODULE - OPERATION,
FRONT..............................8E-7
CONTROL MODULE - OPERATION,
POWER LIFTGATE....................8E-11
CONTROL MODULE - OPERATION, SIDE
IMPACT AIRBAG.....................8O-17
CONTROL MODULE - OPERATION,
SLIDING DOOR......................8E-19
CONTROL MODULE - OPERATION,
TRANSMISSION......................8E-20
CONTROL MODULE - REMOVAL, BODY....8E-4
CONTROL MODULE - REMOVAL, FRONT . . . 8E-8
CONTROL MODULE - REMOVAL, POWER
LIFTGATE...........................8E-11
CONTROL MODULE - REMOVAL, SIDE
IMPACT AIRBAG.....................8O-17
CONTROL MODULE - REMOVAL,
SLIDING DOOR......................8E-19
CONTROL MOTOR - DESCRIPTION, IDLE
AIR ...............................14-28
CONTROL MOTOR - INSTALLATION, IDLE
AIR ...............................14-29
CONTROL MOTOR - OPERATION, IDLE
AIR.................................14-28
CONTROL MOTOR - REMOVAL, IDLE AIR . . 14-29
CONTROL RELAY - DESCRIPTION,
TRANSMISSION.....................21-247
CONTROL RELAY - OPERATION,
TRANSMISSION.....................21-248
CONTROL SWITCH - DIAGNOSIS AND
TESTING, TRACTION...................5-82
CONTROL SYSTEM - DESCRIPTION,
TRACTION...........................5-76
CONTROL SYSTEM - OPERATION,
EVAPORATION.......................25-10
CONTROL SYSTEM - OPERATION,
TRACTION...........................5-77
CONTROLLER - DESCRIPTION,
OCCUPANT RESTRAINT................8O-7
CONTROLLER - INSTALLATION,
OCCUPANT RESTRAINT................8O-7
CONTROLLER - INSTALLATION, SBEC....8E-17
CONTROLLER - OPERATION, 8-VOLT
SUPPLY - PCM OUTPUT - SBEC.........8E-15
CONTROLLER - OPERATION, OCCUPANT
RESTRAINT..........................8O-7
CONTROLLER - REMOVAL, NGC.........8E-17
CONTROLLER - REMOVAL, OCCUPANT
RESTRAINT..........................8O-7
CONTROLLER - REMOVAL, SBEC........8E-16
CONTROLLER ANTILOCK BRAKE -
DESCRIPTION........................8E-5
CONTROLLER ANTILOCK BRAKE -
INSTALLATION........................8E-6
CONTROLLER ANTILOCK BRAKE -
OPERATION..........................8E-5
CONTROLLER ANTILOCK BRAKE -
REMOVAL...........................8E-6
CONVENTIONAL BATTERY CHARGING -
STANDARD PROCEDURE...............8F-11
CONVERTER - DESCRIPTION, CATALYTIC . . . 11-4
CONVERTER - DESCRIPTION, TORQUE . . . 21-242
CONVERTER - INSPECTION, CATALYTIC....11-5
CONVERTER - INSTALLATION, CATALYTIC . . 11-6
CONVERTER - INSTALLATION, TORQUE . . 21-247
CONVERTER - OPERATION, CATALYTIC....11-4
CONVERTER - OPERATION, TORQUE....21-245
CONVERTER - REMOVAL, CATALYTIC......11-5
CONVERTER - REMOVAL, TORQUE......21-247
CONVERTER HOUSING FLUID LEAKAGE -
DIAGNOSIS AND TESTING, TORQUE.....21-123
COOL DOWN TEST - DIAGNOSIS AND
TESTING, A/C
........................24-4
COOLANT - DESCRIPTION, ENGINE
.......7-19
COOLANT - DESCRIPTION, ENGINE
........0-3
COOLANT - STANDARD PROCEDURE,
ADDING ADDITIONAL
...................7-5
COOLANT CONCENTRATION TESTING -
DIAGNOSIS AND TESTING
..............7-19
RSINDEX7
Description Group-Page Description Group-Page Description Group-Page
ProCarManuals.com

LIFTGATE MOTOR - OPERATION.........8N-15
LIFTGATE MOTOR - REMOVAL..........8N-15
LIFTGATE SIDE - INSTALLATION.........23-43
LIFTGATE SIDE - REMOVAL............23-43
LIFTGATE SILL PLATE - INSTALLATION . . . 23-77
LIFTGATE SILL PLATE - REMOVAL.......23-77
LIFTGATE SPOILER - INSTALLATION......23-41
LIFTGATE SPOILER - REMOVAL.........23-41
LIFTGATE SYSTEM - DESCRIPTION,
POWER.............................8N-2
LIFTGATE SYSTEM - DIAGNOSIS AND
TESTING, POWER.....................8N-4
LIFTGATE SYSTEM - OPERATION,
POWER.............................8N-3
LIMITS - DESCRIPTION, HIGH AND LOW . . . 25-8
LINE - INSTALLATION, DISCHARGE......24-69
LINE - INSTALLATION, FUEL...........24-110
LINE - INSTALLATION, LIQUID..........24-82
LINE - INSTALLATION, SUCTION . . . 24-102,24-91
LINE - REMOVAL, DISCHARGE..........24-68
LINE - REMOVAL, FUEL...............24-109
LINE - REMOVAL, LIQUID..............24-80
LINE - REMOVAL, SUCTION......24-101,24-90
LINE AND TERMINAL REPAIR -
STANDARD PROCEDURE, GRID..........8G-3
LINE EXTENSION - INSTALLATION,
EVAPORATOR.......................24-96
LINE EXTENSION - REMOVAL,
EVAPORATOR.......................24-95
LINE REPAIR REAR - STANDARD
PROCEDURE, GRID....................8G-2
LINES - DESCRIPTION, OIL COOLER.....9-138
LINES - DESCRIPTION, UNDERBODY....24-103
LINES - INSTALLATION, OIL COOLER.....9-138
LINES - INSTALLATION, REAR AIR
CONDITIONING.....................24-105
LINES - INSTALLATION, REAR HEATER . . 24-105
LINES - INSTALLATION, TRANSMISSION
OIL COOLER.........................7-38
LINES - OPERATION, OIL COOLER.......9-138
LINES - OPERATION, UNDERBODY......24-103
LINES - REMOVAL, OIL COOLER........9-138
LINES - REMOVAL, REAR AIR
CONDITIONING.....................24-104
LINES - REMOVAL, REAR HEATER......24-104
LINES - REMOVAL, TRANSMISSION OIL
COOLER.............................7-38
LINES/HOSES AND CLAMPS -
DESCRIPTION, FUEL...................14-6
LINING - INSPECTION, REAR DRUM
BRAKE SHOE.........................5-22
LINK - DESCRIPTION, TRD............21-249
LINK - INSTALLATION, FUEL FILL DOOR
BLOCKER LOCKOUT..................23-53
LINK - OPERATION, TRD..............21-249
LINK - REMOVAL, FUEL FILL DOOR
BLOCKER LOCKOUT..................23-52
LINK CONNECTOR - DESCRIPTION, DATA . . 8E-6
LINK CONNECTOR - OPERATION, DATA....8E-7
LINK ROD - DESCRIPTION, LIFT GEAR . . . 8N-16
LINK ROD - INSTALLATION, LIFT GEAR . . . 8N-16
LINK ROD - OPERATION, LIFT GEAR.....8N-16
LINK ROD - REMOVAL, LIFT GEAR.......8N-16
LINKAGE - INSTALLATION, WIPER.......8R-18
LINKAGE - REMOVAL, WIPER...........8R-17
LIQUID LINE - INSTALLATION...........24-82
LIQUID LINE - REMOVAL
..............24-80
LOADS - STANDARD PROCEDURE,
TESTING FOR A SHORT TO GROUND
ON FUSES POWERING SEVERAL
.....8W-01-10
LOCATION - DESCRIPTION, CONNECTOR/
GROUND/SPLICE
...................8W-91-1
LOCATIONS - DESCRIPTION, FLUID
FILL/CHECK
...........................0-7
LOCATIONS - SPECIFICATIONS, BODY
SEALING
..........................23-127
LOCATIONS - SPECIFICATIONS,
STRUCTURAL ADHESIVE
..............23-153
LOCATIONS - SPECIFICATIONS, WELD
. . . 23-161
LOCK ASSEMBLY - INSTALLATION,
LATCH
.............................23-27
LOCK ASSEMBLY - REMOVAL, LATCH
....23-26
LOCK CYLINDER - INSTALLATION
. . 23-20,23-41
LOCK CYLINDER - REMOVAL
......23-19,23-41
LOCK CYLINDER HOUSING -
INSTALLATION
.......................19-19
LOCK CYLINDER HOUSING - REMOVAL
. . . 19-17LOCK MOTOR - DIAGNOSIS AND
TESTING, DOOR.....................8N-41
LOCK MOTOR - INSTALLATION, SLIDING
DOOR.............................8N-44
LOCK MOTOR - REMOVAL, SLIDING
DOOR.............................8N-44
LOCK SWITCH - DESCRIPTION, DOOR
CYLINDER..........................8N-40
LOCK SWITCH - DIAGNOSIS AND
TESTING, DOOR.....................8N-41
LOCK SWITCH - DIAGNOSIS AND
TESTING, DOOR CYLINDER............8N-40
LOCK SWITCH - INSTALLATION, DOOR . . . 8N-42
LOCK SWITCH - INSTALLATION, DOOR
CYLINDER..........................8N-41
LOCK SWITCH - OPERATION, DOOR
CYLINDER..........................8N-40
LOCK SWITCH - REMOVAL, DOOR.......8N-42
LOCK SWITCH - REMOVAL, DOOR
CYLINDER..........................8N-41
LOCKED ENGINE - STANDARD
PROCEDURE, HYDROSTATIC.........9-10,9-85
LOCK/LATCH - INSTALLATION, UNDER
SEAT STORAGE BIN.................23-104
LOCK/LATCH - REMOVAL, UNDER SEAT
STORAGE BIN......................23-104
LOCKOUT LINK - INSTALLATION, FUEL
FILL DOOR BLOCKER.................23-53
LOCKOUT LINK - REMOVAL, FUEL FILL
DOOR BLOCKER.....................23-52
LOCKS - DESCRIPTION, POWER........8N-38
LOCKS - OPERATION, POWER..........8N-39
LOUVER - INSTALLATION, REAR HVAC . . . 23-79
LOUVER - REMOVAL, REAR HVAC.......23-79
LOW LIMITS - DESCRIPTION, HIGH.......25-8
LOWER - CLEANING, INTAKE MANIFOLD . . 9-148
LOWER - INSPECTION, INTAKE
MANIFOLD......................9-148,9-60
LOWER - INSTALLATION, INTAKE
MANIFOLD...........................9-60
LOWER - INSTALLATION, SHROUD.......19-22
LOWER - REMOVAL, INTAKE MANIFOLD . . . 9-60
LOWER - REMOVAL, SHROUD..........19-21
LOWER BALL JOINT - DESCRIPTION......2-10
LOWER BALL JOINT - DIAGNOSIS AND
TESTING............................2-10
LOWER BALL JOINT - OPERATION........2-10
LOWER CONSOLE - INSTALLATION......23-68
LOWER CONSOLE - REMOVAL..........23-68
LOWER CONTROL ARM - DESCRIPTION . . . 2-12
LOWER CONTROL ARM - INSPECTION.....2-14
LOWER CONTROL ARM - INSTALLATION . . . 2-15
LOWER CONTROL ARM - OPERATION.....2-12
LOWER CONTROL ARM - REMOVAL......2-12
LOWER CONTROL ARM (REAR BUSHING
- HYDRO) - ASSEMBLY.................2-14
LOWER CONTROL ARM (REAR BUSHING
- HYDRO) - DISASSEMBLY..............2-14
LOWER CONTROL ARM (REAR BUSHING
- STANDARD) - ASSEMBLY..............2-14
LOWER CONTROL ARM (REAR BUSHING
- STANDARD) - DISASSEMBLY...........2-13
LOWER DRIVE UNIT - DESCRIPTION.....8N-32
LOWER DRIVE UNIT - INSTALLATION....8N-33
LOWER DRIVE UNIT - OPERATION.......8N-32
LOWER DRIVE UNIT - REMOVAL
........8N-33
LOWER DRIVE UNIT TRACK & RACK -
DESCRIPTION
.......................8N-34
LOWER DRIVE UNIT TRACK & RACK -
INSTALLATION
......................8N-34
LOWER DRIVE UNIT TRACK & RACK -
OPERATION
.........................8N-34
LOWER DRIVE UNIT TRACK & RACK -
REMOVAL
..........................8N-34
LOWER EXTENSION TRIM -
INSTALLATION, A-PILLAR
..............23-73
LOWER EXTENSION TRIM - REMOVAL,
A-PILLAR
...........................23-73
LOWER HINGE - INSTALLATION
.........23-28
LOWER HINGE - REMOVAL
.............23-28
LOWER INSTRUMENT PANEL -
INSTALLATION
.......................23-68
LOWER INSTRUMENT PANEL -
REMOVAL
..........................23-68
LOWER INTAKE MANIFOLD -
INSTALLATION
.......................9-149
LOWER INTAKE MANIFOLD - REMOVAL
. . . 9-148LOWER STEERING COLUMN COVER -
INSTALLATION.......................23-69
LOWER STEERING COLUMN COVER -
REMOVAL..........................23-69
LOWER TRIM - INSTALLATION,
B-PILLAR...........................23-74
LOWER TRIM - REMOVAL, B-PILLAR.....23-73
LUBRICANTS - DESCRIPTION, ENGINE
OIL .................................0-1
LUBRICATION - DESCRIPTION......9-136,9-52
LUBRICATION - OPERATION........9-136,9-52
LUBRICATION - STANDARD PROCEDURE....2-2
LUBRICATION POINTS - DESCRIPTION......0-7
LUBRICATION, SPECIFICATIONS - BODY . . 23-12
LUGGAGE RACK CROSSBAR -
INSTALLATION.......................23-56
LUGGAGE RACK CROSSBAR - REMOVAL . . 23-55
LUGGAGE RACK RISER - INSTALLATION . . 23-55
LUGGAGE RACK RISER - REMOVAL......23-54
LUMBAR SUPPORT - INSTALLATION....23-104
LUMBAR SUPPORT - REMOVAL........23-104
LWB - INSTALLATION, SEAT BELT &
RETRACTOR - SECOND ROW - RIGHT
OUTBOARD WITH REAR HVAC..........8O-15
LWB - REMOVAL, SEAT BELT &
RETRACTOR - SECOND ROW - RIGHT
OUTBOARD WITH REAR HVAC..........8O-15
MACHINING - STANDARD PROCEDURE,
BRAKE ROTOR.......................5-53
MAIN BEARING FITTING - STANDARD
PROCEDURE..........................9-123
MAIN BEARINGS - INSTALLATION,
CRANKSHAFT.......................9-124
MAIN BEARINGS - REMOVAL,
CRANKSHAFT.......................9-124
MAINTENANCE SCHEDULES -
DESCRIPTION.........................0-7
MANAGER - DESCRIPTION, TASK........25-24
MANAGER - OPERATION, TASK.........25-24
MANIFOLD - CLEANING, EXHAUST........9-61
MANIFOLD - DESCRIPTION, INTAKE . . 9-144,9-58
MANIFOLD - INSPECTION, EXHAUST......9-61
MANIFOLD - INSTALLATION, EXHAUST....9-61
MANIFOLD - INSTALLATION, LOWER
INTAKE ............................9-149
MANIFOLD - INSTALLATION, UPPER
INTAKE ............................9-147
MANIFOLD - LEFT - CLEANING,
EXHAUST...........................9-152
MANIFOLD - LEFT - INSPECTION,
EXHAUST...........................9-152
MANIFOLD - LEFT - INSTALLATION,
EXHAUST...........................9-152
MANIFOLD - LEFT - REMOVAL, EXHAUST . 9-152
MANIFOLD - LOWER - CLEANING,
INTAKE ............................9-148
MANIFOLD - LOWER - INSPECTION,
INTAKE ........................9-148,9-60
MANIFOLD - LOWER - INSTALLATION,
INTAKE .............................9-60
MANIFOLD - LOWER - REMOVAL,
INTAKE .............................9-60
MANIFOLD - REMOVAL, EXHAUST........9-61
MANIFOLD - REMOVAL, LOWER INTAKE . . 9-148
MANIFOLD - REMOVAL, UPPER INTAKE . . . 9-145
MANIFOLD - RIGHT - CLEANING,
EXHAUST...........................9-151
MANIFOLD - RIGHT - INSPECTION,
EXHAUST...........................9-151
MANIFOLD - RIGHT - INSTALLATION,
EXHAUST...........................9-151
MANIFOLD - RIGHT - REMOVAL,
EXHAUST...........................9-150
MANIFOLD - UPPER - INSPECTION,
INTAKE .............................9-59
MANIFOLD - UPPER - INSTALLATION,
INTAKE .............................9-59
MANIFOLD - UPPER - REMOVAL, INTAKE . . 9-58
MANIFOLD LEAKS - DIAGNOSIS AND
TESTING, INTAKE
................9-145,9-58
MANIFOLD STRIPPED THREAD REPAIR -
STANDARD PROCEDURE
...............9-145
MANIFOLD VACUUM PORT REPAIR -
STANDARD PROCEDURE, INTAKE
........9-145
MANUAL - INSTALLATION, WINDOW
REGULATOR
........................23-23
MANUAL - REMOVAL, WINDOW
REGULATOR
........................23-23
RSINDEX19
Description Group-Page Description Group-Page Description Group-Page
ProCarManuals.com