change wheel CHRYSLER PACIFICA 2018 Vehicle Warranty

When rotating tires with a directional tread pattern, observe the arrows
molded on the sidewall which show the direction the tire should turn.
Care must be taken to maintain the proper turning direction.
Some Tire Pressure Monitoring Systems (TPMS) may not recognize
that a tire has been moved to a different position on your vehicle. Make
certain that your TPMS system is reset, if necessary, so as to correctly
identify the location of each tire on your vehicle. Refer to your vehicle
owner ’s manual or your vehicle dealer.
Determine whether rotated tires require tire inflation adjustment as front
and rear position tire pressure may vary according to the vehicle
manufacturer ’s specification due to the actual load on that wheel
position. Some vehicles may have different sized tires mounted on the
front and rear axles, and these different sized tires have rotation
restrictions. Always check the vehicle owner ’s manual for the proper
rotation recommendations.
Full-size Spare
Full-size spare tires (not temporary spares) of the same size and construc-
tion should be used in a five (5) tire rotation. Always check the inflation
pressure of the full-size spare immediately before incorporating it into
rotation. Follow the vehicle manufacturer ’s recommended pattern for
rotation, or if not available, see a qualified tire technician.
Replacement of Two (2) Tires
It is recommended that all four (4) tires are replaced at the same time.
However, when only two tires are replaced, the new tires should be put
on the rear. The new tires, with deeper tread, may provide better grip and
water evacuation in wet driving conditions.
CUSTOMIZATION OF TIRES, WHEELS, OR SUSPENSION ON
SUVS AND LIGHT TRUCKS
Due to their size, weight and higher center of gravity, vehicles such as
SUVs and light trucks do not have the same handling characteristics as
automobiles. Because of these differing characteristics, failure to operate
your SUV/truck in a proper and safe manner can increase the likelihood
of vehicle rollover. Modifications to your SUV/truck tire size, tire type,
wheels or suspension can change its handling characteristics and further
increase the likelihood of vehicle rollover. Whether your SUV/truck has
the original equipment configuration for tires, wheels and suspension or
whether any of these items have been modified, always drive safely,
MICHELIN
178

avoid sudden, sharp turns or lane changes and obey all traffic laws.
Failure to do so may result in loss of vehicle control leading to an accident
and serious injury or death.
TIRE ALTERATIONS
Do not make or allow to be made any alterations on your tires.
Alterations may prevent proper performance, leading to tire damage
which can result in an accident. Tires which become unserviceable due to
alterations such as truing, whitewall inlays, addition of balancing or
sealant liquids, or the use of tire dressing containing petroleum distillates
are excluded from warranty coverage.
REPAIRS WHEREVER POSSIBLE, SEE YOUR MICHELIN® TIRE
RETAILER AT ONCE
If any MICHELIN® tire sustains a puncture, have the tire demounted
and thoroughly inspected by any Michelin tire retailer for possible
damage that may have occurred. A tread area puncture in any MI-
CHELIN® passenger or light truck tire can be repaired provided that the
puncture hole is not more than 1/4” in diameter, not more than one radial
cable per casing ply is damaged, and the tire has not been damaged
further by the puncturing object or by running underinflated. Tire
punctures consistent with these guidelines can be repaired by following
the Rubber Manufacturers Association (RMA) recommended repair
procedures.
TIRE REPAIRS
Repairs of all tires must be of the combined plug and inside patch type.
Your MICHELIN® PAX® System tires must be removed from the wheel
for inspection prior to repair. Plug only repairs are improper. A tire
should be removed from the rim and inspected prior to repair. Any tire
repair done without removing the tire from the rim is improper. An
improperly repaired tire will cause further damage to the tire by either
leaking air or allowing air, moisture and contaminants to enter the
structure of the tire. An improperly repaired tire can fail suddenly at a
later date.
Never repair a tire with less than 2/32 nds of an inch tread remaining. At
this tread depth, the tire is worn out and must be replaced.
MICHELIN
179

ROADSIDE ASSISTANCE
Patterns sold after May 1st 2014 by NEXEN TIRE in the United States and
Canada are eligible for a free 24/7/365 Roadside Assistance for a period
of 36 months from the purchase date. Upon purchasing Nexen tires, the
consumer will receive an activation card from the tire shop. An online
registration needs to be completed in order to have access to a toll free
phone number to call in case of a flat tire. A qualified professional will
change your flat tire with your spare tire free of charge. If a working spare
is not available, towing will be provided free of charge to the nearest
NEXEN TIRE dealer or authorized place of repair.
*Nexen Tire reserves the right to change the terms and conditions of all
warranties at any time.
TIRE CARE AND MAINTENANCE GUIDE
Tire failure can result in serious damage and/or personal injury. To
reduce the risk of tire failure we recommend the following:
•Maintain proper inflation pressure and do not use at under inflation or
over inflation. Pressure should be set at the level recommended by
vehicle manufacturer.
•Wheel alignment and balancing should be checked at regular intervals.
•Do not overload. The maximum load carrying capacity is molded on
the sidewall of the tire.
•Do not spin your tires excessively and avoid driving over curbs,
potholes, obstacles and edges of pavement.
•Never drive on smooth (bald) tires. By law, tires must be replaced
when 2/32of tread depth remained, as indicated by tread wear
indicator molded in the tread grooves.
•Check your tires frequently for any scrapes, cuts, foreign objects,
separations or bulges. If damage is found, do not attempt to dismount
a tire yourself. Change damaged tire with the spare and contact your
local authorized NEXEN TIRE dealer immediately.
•Do not drive in excess of speed limits allowed by law or the maximum
speed justified by driving conditions.
•To achieve proper even wear and gain maximum tread life, tire
rotation at regular intervals is required.
NEXEN TIRE
191

Pirelli “Seal Inside” Technology
Select Pirelli tires incorporate “Seal Inside” technology, a construction
designed to stop the loss of air from a tire when punctured by an object.
Providing the puncture does not compromise the structural integrity of
the tire, a sealing material layer prevents possible air leakage in the event
of a carcass puncture.
The “Seal Inside ” technology is not designed or intended to be a
permanent repair, and is only meant to allow the consumer to go to a
Pirelli dealer for an inspection to determine if repair or replacement is
needed.
Visit
www.ca.pirelli.comfor more information.
What Is Not Covered By The Warranty?
•Tires on any vehicle registered and normally operated outside the
United States of America or Canada.
•Tires transferred from the vehicle on which they were originally
installed.
•Tires misapplied due to insufficient Speed Rating, Load Index, under-
sized or oversized tires.
•Tires damaged from improper mounting/dismounting practices,
abuse, misuse, or neglect.
•Tire dealer/retailer services: mounting, dismounting, balancing, stud-
ding, tire rotation, or wheel alignment.
•Mileage warranty on tires fitted as Original Equipment (Pirelli brand
tires supplied as original equipment on new vehicles).
•Passenger tires ( Euro-metric / P-metric ) used on commercial vehicles
or used in commercial applications.
•Tires in which any thing other than air or nitrogen has been used as the
support medium.
•Tires injected with liquid balancer or sealant or any other balancing
material.
•Tires which have been modified by the addition or removal of material
or any tire intentionally altered to change its appearance.
PIRELLI TIRES
202

8. Tire Replacement
The tires fitted to your vehicle as original equipment were tested and
approved by the vehicle manufacturer and the tire manufacturer and take
into account all aspects of the vehicle’s operation. Changes in the tire size,
type or construction should not be made without seeking advice from the
vehicle or tire manufacturer or an authorized Pirelli dealer since unap-
proved tires on your vehicle could adversely affect steering, handling,
braking and traction. The tire information (tire size, load index and speed
symbol) as found on the vehicle placard or in the owner ’s manual should
always be followed when replacing tires.
It is strongly recommended that Pirelli tires be mounted in sets of four
with the same tread type. Pirelli tires should not be mixed with other tire
brands. It is necessary to follow this procedure because different tire
constructions have different handling characteristics. Tires on the same
axle must be the same manufacturer, brand, tire size, load index, speed
rating and Pirelli part number.
When changing only two tires on a vehicle which is homogeneously
fitted (four tires of the same tire size), fit the new tires on the rear axle.
This applies to all vehicles regardless of their drive axle. (Front or Rear
Drive).
On all wheel drive or four wheel drive vehicles the tires must always be
replaced in sets of four.
When replacing tires on light truck vehicles, you should always follow
the vehicle manufacturer ’s recommendations. Passenger and light truck
tires are not interchangeable, due to differences in their pressures and
load carrying capacity.
P-Metric and Euro-metric Interchangeability: Euro-metric (Example: 225/
45R17) tires have a load index which is equal to or greater than that of the
same size P-metric (Example: P225/45R17) tire. Therefore, they have the
same or higher load carrying capacity at the maximum rated inflation
pressure. Always check with your tire dealer or Pirelli Tire Consumer
Affairs to be sure of the exact interchangeability to maintain proper
vehicle dynamics.
Please be aware that it is important that, before fitting the suggested tires,
the fitment is allowed by the technical specifications of the vehicle, the
vehicle manufacturer and the relevant homologations. Pirelli Tire does
not express any view as to the compatibility of the wheel/tire combina-
tion with the technical specifications for the chassis and vehicle.
PIRELLI TIRES
211

WARNING!(Continued)
Pull over to a safe area as soon as possible and inspect the tires for
signs of bulges, blisters, or separations. Seek roadside assistance or
change the damaged tire with your spare tire.
If you experience a blowout or a sudden tire failure, the following
information should be helpful:
•When the tire failure occurs, you may hear a loud noise, or feel a
vibration, and/or the vehicle may pull toward the side of the failed
tire. Do not abruptly brake or turn.
•Maintain steady pressure on the accelerator pedal.
•Hold the steering wheel firmly and steer to maintain your lane
position.
•Find a safe place to pull off the road and allow the vehicle to gradually
decelerate. Apply light braking as required to stop safely.
•Gradually pull over to the shoulder and come to a stop. Look for a
damaged tire on your vehicle.
•Seek roadside assistance or change the damaged tire with your spare
tire.
•Have all of your tires and the vehicle thoroughly inspected by a tire
professional.
TIRE ROTATION
The purpose for rotating tires is to achieve more uniform wear for all tires
on a vehicle. Your tires should be thoroughly examined on a lift by a tire
dealer for any abnormalities. If tires show uneven treadwear, ask the
service person to check and/or correct any vehicle wheel alignment or
other mechanical problem before rotation.
The following rotation patterns are acceptable. Please refer to your
vehicle Owner ’s Manual for rotation advice.
TOYO TIRES – LIMITED WARRANTY
241

More frequent rotation or a thorough vehicle inspection may be necessary
if, upon inspection, irregular or erratic treadwear is beginning to appear.
It is important to remember the following:
•These tire rotation recommendations do not take into account different
tire and construction types mixed on the vehicle.
•Some tires cannot be rotated in the manner described. Such tires
include unidirectional tires. Unidirectional tread patterns must be
rotated front-to-rear only so that the direction of revolution does not
change.
•Some vehicles are designed with different tire sizes on the front and
rear axles. Normally, such combinations will not allow rotation. Prior
to rotating, consult the vehicle Owner ’s Manual.
•For vehicles with dual rear wheels, see the vehicle Owner ’s Manual for
the vehicle manufacturer ’s procedures. If your vehicle Owner ’s
Manual is not available, please contact the vehicle manufacturer.
•Some vehicles are equipped with wheels that limit the choice of
rotation pattern. Consult the vehicle Owner ’s Manual.
•Do not include temporary spare tires in the rotation pattern. However,
if your spare tire is the same size and type as a road tire (for LT tires
of the same size, type, and load rating), it should be included in the tire
rotation process. The proper procedure is to use the vehicle manufac-
turer ’s recommended tire rotation procedures, or if not available, to
use the appropriate rotation pattern shown, inserting the spare in the
right rear position. Place the tire that would have gone to the right rear
in the spare tire storage position as the new spare.
•Important! After rotation, adjust the pressure of the individual tires to
the vehicle manufacturer ’s recommendation or the inflation pressure
recommended by Toyo Tires for an optional fitment according to the
tire’s new location on the vehicle.
•Do not mix speed-rated tires on the same axle. Higher speed-rated tires
must remain on the rear axle. Consult your authorized Toyo Tires
dealer.
TOYO TIRES – LIMITED WARRANTY
243

speeds in excess of 65 mph may be required, then the following
adjustments or recommendations should be followed:
•At speeds from 66 mph through 75 mph, cold inflation pressure must
be increased 10 psi above the recommended pressures for the load
being carried.
•Do not exceed the maximum inflation pressure of the wheel (all wheels
have maximum allowable inflation pressures).
REPLACEMENT TIRES FOR LIGHT TRUCKS – P-METRIC VS .
LT-TRUCK
Tire installers should exercise extreme caution when replacing tires on
light trucks.
The maximum load capacity stamped on the sidewall of a P-metric tire is
reduced by a factor of 1.1 when used on a light truck, a sport utility
vehicle, or a trailer.
WARNING!
•P-metric and LT-metric tires are not necessarily interchangeable.
P-metric and LT-metric tires follow completely different Load/
Inflation tables and are designed to carry different loads at
different pressures.
(Continued)
TOYO TIRES – LIMITED WARRANTY
252

WARNING!(Continued)
Pull over to a safe area as soon as possible and inspect the tires for
signs of bulges, blisters, or separations. Seek roadside assistance or
change the damaged tire with your spare tire.
If you experience a blowout or a sudden tire failure, the following
information should be helpful:
•When the tire failure occurs, you may hear a loud noise, or feel a
vibration, and/or the vehicle may pull toward the side of the failed
tire. Do not abruptly brake or turn.
•Maintain steady pressure on the accelerator pedal.
•Hold the steering wheel firmly and steer to maintain your lane
position.
•Find a safe place to pull off the road and allow the vehicle to gradually
decelerate. Apply light braking as required to stop safely.
•Gradually pull over to the shoulder and come to a stop. Look for a
damaged tire on your vehicle.
•Seek roadside assistance or change the damaged tire with your spare
tire.
•Have all of your tires and the vehicle thoroughly inspected by a tire
professional.
TIRE ROTATION
The purpose for rotating tires is to achieve more uniform wear for all tires
on a vehicle. Your tires should be thoroughly examined on a lift by a tire
dealer for any abnormalities. If tires show uneven treadwear, ask the
service person to check and/or correct any vehicle wheel alignment or
other mechanical problem before rotation.
The following rotation patterns are acceptable. Please refer to your
vehicle Owner ’s Manual for rotation advice.
NITTO TIRE
296

More frequent rotation or a thorough vehicle inspection may be necessary
if, upon inspection, irregular or erratic treadwear is beginning to appear.
It is important to remember the following:
•These tire rotation recommendations do not take into account different
tire and construction types mixed on the vehicle.
•Some tires cannot be rotated in the manner described. Such tires
include unidirectional tires. Unidirectional tread patterns must be
rotated front-to-rear only so that the direction of revolution does not
change.
•Some vehicles are designed with different tire sizes on the front and
rear axles. Normally, such combinations will not allow rotation. Prior
to rotating, consult the vehicle Owner ’s Manual.
•For vehicles with dual rear wheels, see the vehicle Owner ’s Manual for
the vehicle manufacturer ’s procedures. If your vehicle Owner ’s
Manual is not available, please contact the vehicle manufacturer.
•Some vehicles are equipped with wheels that limit the choice of
rotation pattern. Consult the vehicle Owner ’s Manual.
•Do not include temporary spare tires in the rotation pattern. However,
if your spare tire is the same size and type as a road tire (for LT tires
of the same size, type, and load rating), it should be included in the tire
rotation process. The proper procedure is to use the vehicle manufac-
turer ’s recommended tire rotation procedures, or if not available, to
use the appropriate rotation pattern shown, inserting the spare in the
right rear position. Place the tire that would have gone to the right rear
in the spare tire storage position as the new spare.
•Important! After rotation, adjust the pressure of the individual tires to
the vehicle manufacturer ’s recommendation or the inflation pressure
recommended by Nitto for an optional fitment according to the tire’s
new location on the vehicle.
•Do not mix speed-rated tires on the same axle. Higher speed-rated tires
must remain on the rear axle. Consult your authorized Nitto dealer.
TIRE SPEED RATING
All Nitto passenger and light truck tires have a maximum speed rating
based on size and type. Tires must never be operated in excess of their
rated speed limit! Consult your tire dealer or contact Nitto at
NITTO TIRE
298