homelink CHRYSLER PACIFICA HYBRID 2018 Owners Manual

WINDOWS ........................... .120
▫ Power Windows ....................... .120
 TRI-PANE PANORAMIC SUNROOF —
IF EQUIPPED ......................... .123
▫ Opening Sunroof ...................... .124
▫ Closing Sunroof ....................... .125
▫ Wind Buffeting ....................... .125
▫ Power Sun Shade — If Equipped ............125
▫ Pinch Protect Feature ....................126
▫ Sunroof Maintenance ....................126
▫ Ignition Off Operation ...................126
 HOOD .............................. .126
▫ Opening ............................ .126
▫ Closing ............................. .128
 LIFTGATE ............................ .128
▫ Opening ............................ .128
▫ Closing ............................ .130▫
Power Liftgate — If Equipped ..............130
▫ Hands-Free Liftgate — If Equipped ..........132
▫ Cargo Area Features ....................134
 GARAGE DOOR OPENER — IF EQUIPPED . . . .134
▫ Before You Begin Programming HomeLink .....135
▫ Canadian/Gate Operator Programming .......138
▫ Using HomeLink ...................... .139
▫ Security ............................. .139
▫ Troubleshooting Tips ....................139
▫ General Information .....................140
 INTERNAL

EQUIPMENT ..................141
▫ Storage ............................. .141
▫ Power Outlets ........................ .144
▫ Power Inverter — If Equipped .............147
▫ Cigar Lighter — If Equipped ...............148
▫ Smoker’s Package Kit — If Equipped ........149
▫ Overhead Sunglass Storage ...............149
16 GETTING TO KNOW YOUR VEHICLE

Gas props support the liftgate in the open position. How-
ever, because the gas pressure drops with temperature, it
may be necessary to assist the props when opening the
liftgate in cold weather.
NOTE:Allow the power system to open the liftgate.
Manually pushing or pulling the liftgate may activate the
liftgate obstacle detection feature and stop the power
operation or reverse its direction.
WARNING!
During power operation, personal injury or cargo
damage may occur. Ensure the liftgate travel path is
clear. Make sure the liftgate is closed and latched
before driving away.
Cargo Area Features
Cargo Area Storage
When the third row seats are not in the stowed position,
there is a large area for cargo storage. NOTE:
With all rear seats stowed or removed, four by
eight foot sheets of building material will fit on the vehicle
floor with the liftgate closed. The front seats must be
moved slightly forward of the rearmost position.GARAGE DOOR OPENER — IF EQUIPPED
HomeLink replaces up to three hand-held transmitters that
operate devices such as garage door openers, motorized
gates, lighting or home security systems. The HomeLink
unit is powered by your vehicles 12 Volt battery.
Rear Cargo Area
134 GETTING TO KNOW YOUR VEHICLE

The HomeLink buttons, located on the driver ’s sunvisor,
designate the three different HomeLink channels. The
HomeLink indicator is located above the center button.
NOTE:HomeLink is disabled when the Vehicle Security
Alarm is active.
Before You Begin Programming HomeLink
Be sure that your vehicle is parked outside of the garage
before you begin programming.
For more efficient programming and accurate transmission
of the radio-frequency signal it is recommended that a new battery be placed in the hand-held transmitter of the device
that is being programmed to the HomeLink system.
To erase the channels, place the ignition in the ON/RUN
position, and push and hold the two outside HomeLink
buttons (I and III) for up to 20 seconds or until the orange
indicator flashes.
NOTE:
•
Erasing all channels should only be performed when
programming HomeLink for the first time. Do not erase
channels when programming additional buttons.
• If you have any problems, or require assistance, please
call toll-free 1-800-355-3515 or, on the Internet at
HomeLink.com for information or assistance.
Programming A Rolling Code
For programming garage door openers that were manufac-
tured after 1995. These garage door openers can be identi-
fied by the “LEARN” or “TRAIN” button located where
the hanging antenna is attached to the garage door opener.
NOTE: It is NOT the button that is normally used to open
and close the door. The name and color of the button may
vary by manufacturer.
HomeLink Buttons/Overhead Console
3
GETTING TO KNOW YOUR VEHICLE 135

1. Place the ignition in the ON/RUN position.
2. Place the hand-held transmitter 1 to 3 inches (3 to 8 cm)away from the HomeLink button you wish to program
while keeping the HomeLink indicator light in view.
3. Push and hold the HomeLink button you want to program while you push and hold the hand-held trans-
mitter button. 4. Continue to hold both buttons and observe the indicator
light. The HomeLink indicator will flash slowly and
then rapidly after HomeLink has received the frequency
signal from the hand-held transmitter. Release both
buttons after the indicator light changes from slow to
rapid.
5. At the garage door opener motor (in the garage), locate the “LEARN” or “TRAINING” button. This can usually
be found where the hanging antenna wire is attached to
the garage door opener/device motor. Firmly push and
release the “LEARN” or “TRAINING” button. On some
garage door openers/devices there may be a light that
blinks when the garage door opener/device is in the
LEARN/TRAIN mode.
NOTE: You have 30 seconds in which to initiate the next
step after the LEARN button has been pushed.
6. Return to the vehicle and push the programmed HomeLink button twice (holding the button for two
seconds each time). If the garage door opener/device
activates, programming is complete.
NOTE: If the garage door opener/device does not activate,
push the button a third time (for two seconds) to complete
the training.
Training The Garage Door Opener
1 — Door Opener
2 — Training Button 136 GETTING TO KNOW YOUR VEHICLE

To program the remaining two HomeLink buttons, repeat
each step for each remaining button. DO NOT erase the
channels.
Reprogramming A Single HomeLink Button (Rolling Code)
To reprogram a channel that has been previously trained,
follow these steps:
1. Cycle the ignition to the ON/RUN position.
2. Push and hold the desired HomeLink button until theindicator light begins to flash after 20 seconds. Do not
release the button.
3. Without releasing the button proceed with “Program- ming A Rolling Code” step 2 and follow all remaining
steps.
Programming A Non-Rolling Code
For programming Garage Door Openers manufactured
before 1995.
1. Cycle the ignition to the ON/RUN position.
2. Place the hand-held transmitter 1 to 3 inches (3 to 8 cm)away from the HomeLink button you wish to program
while keeping the HomeLink indicator light in view. 3. Press and hold the HomeLink button you want to
program while you press and hold the hand-held trans-
mitter button.
4. Continue to hold both buttons and observe the indicator light. The HomeLink indicator will flash slowly and
then rapidly after HomeLink has received the frequency
signal from the hand-held transmitter. Release both
buttons after the indicator light changes from slow to
rapid.
5. Press and hold the programmed HomeLink button and observe the indicator light.
• If the indicator light stays on constantly, programming
is complete and the garage door/device should acti-
vate when the HomeLink button is pressed.
• To program the two remaining HomeLink buttons,
repeat each step for each remaining button. DO NOT
erase the channels.
Reprogramming A Single HomeLink Button (Non-Rolling
Code)
To reprogram a channel that has been previously trained,
follow these steps:
1. Cycle the ignition to the ON/RUN position.
3
GETTING TO KNOW YOUR VEHICLE 137

2. Press and hold the desired HomeLink button until theindicator light begins to flash after 20 seconds. Do not
release the button.
3. Without releasing the button, proceed with “Program- ming A Non-Rolling Code” step 2 and follow all remain-
ing steps.
Canadian/Gate Operator Programming
For programming transmitters in Canada/United States
that require the transmitter signals to “time-out” after
several seconds of transmission.
Canadian radio frequency laws require transmitter signals
to time-out (or quit) after several seconds of transmission –
which may not be long enough for HomeLink to pick up
the signal during programming. Similar to this Canadian
law, some U.S. gate operators are designed to time-out in
the same manner.
It may be helpful to unplug the device during the cycling
process to prevent possible overheating of the garage door
or gate motor.
1. Cycle the ignition to the ON/RUN position. 2. Place the hand-held transmitter 1 to 3 inches (3 to 8 cm)
away from the HomeLink button you wish to program
while keeping the HomeLink indicator light in view.
3. Continue to press and hold the HomeLink button, while you press and release (“cycle”) your hand-held trans-
mitter every two seconds until HomeLink has success-
fully accepted the frequency signal. The indicator light
will flash slowly and then rapidly when fully trained.
4. Watch for the HomeLink indicator to change flash rates. When it changes, it is programmed. It may take up to 30
seconds or longer in rare cases. The garage door may
open and close while you are programming.
5. Press and hold the programmed HomeLink button and observe the indicator light.
NOTE: •If the indicator light stays on constantly, programming
is complete and the garage door/device should acti-
vate when the HomeLink button is pressed.
• To program the two remaining HomeLink buttons,
repeat each step for each remaining button. DO NOT
erase the channels.
138 GETTING TO KNOW YOUR VEHICLE

If you unplugged the garage door opener/device for
programming, plug it back in at this time.
Reprogramming A Single HomeLink Button (Canadian/
Gate Operator)
To reprogram a channel that has been previously trained,
follow these steps:
1. Cycle the ignition to the ON/RUN position.
2. Press and hold the desired HomeLink button until theindicator light begins to flash after 20 seconds. Do not
release the button.
3. Without releasing the button, proceed with “Canadian/ Gate Operator Programming” step 2 and follow all
remaining steps.
Using HomeLink
To operate, push and release the programmed HomeLink
button. Activation will now occur for the programmed
device (i.e. garage door opener, gate operator, security
system, entry door lock, home/office lighting, etc.). The
hand-held transmitter of the device may also be used at
any time.
Security
It is advised to erase all channels before you sell or turn in
your vehicle.
To do this, push and hold the two outside buttons for
20 seconds until the orange indicator flashes. Note that all
channels will be erased. Individual channels cannot be
erased.
The HomeLink Universal Transceiver is disabled when the
Vehicle Security Alarm is active.
Troubleshooting Tips
If you are having trouble programming HomeLink, here
are some of the most common solutions:
•Replace the battery in the Garage Door Opener hand-
held transmitter.
• Push the LEARN button on the Garage Door Opener to
complete the training for a Rolling Code.
• Did you unplug the device for programming and re-
member to plug it back in?
If you have any problems, or require assistance, please call
toll-free 1-800-355-3515 or, on the Internet at HomeLink.com
for information or assistance.
3
GETTING TO KNOW YOUR VEHICLE 139

WARNING!
•Vehicle exhaust contains carbon monoxide, a danger-
ous gas. Do not run your vehicle in the garage while
programming the transceiver. Exhaust gas can cause
serious injury or death.
• Your motorized door or gate will open and close
while you are programming the universal trans-
ceiver. Do not program the transceiver if people, pets
or other objects are in the path of the door or gate.
Only use this transceiver with a garage door opener
that has a “stop and reverse” feature as required by
Federal safety standards. This includes most garage
door opener models manufactured after 1982. Do not
use a garage door opener without these safety fea-
tures. Call toll-free 1-800-355-3515 or, on the Internet
at HomeLink.com for safety information or assis-
tance.
General Information
The following regulatory statement applies to all Radio
Frequency (RF) devices equipped in this vehicle:
This device complies with Part 15 of the FCC Rules and
with Industry Canada license-exempt RSS standard(s).
Operation is subject to the following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, in- cluding interference that may cause undesired opera-
tion.
NOTE: Changes or modifications not expressly approved
by the party responsible for compliance could void the
user ’s authority to operate the equipment.
140 GETTING TO KNOW YOUR VEHICLE

Starting.............................. .278
Engine Oil Viscosity ........................ .439
Engine Oil Viscosity Chart ....................439
Enhanced Accident Response Feature .........246, 428
Ethanol ................................. .495
Exhaust Gas Caution .....................271, 497
Exhaust System ....................... .271, 451
Exterior Lighting ....................... .93, 388
Exterior Lights ...................93, 274, 384, 388
Filters Air Cleaner ............................ .440
Air Conditioning ......................119,443
Engine Oil ......................... .440, 499
Engine Oil Disposal ...................... .439
Flashers Hazard Warning ........................ .378
Turn Signal ....................93, 182, 274, 387
Flash-To-Pass ........................... .93, 95
Fluid, Brake ............................. .501
Fluid Capacities ........................... .498
Fluid Leaks .............................. .274
Fluid Level Checks Brake ................................ .459
Fluids And Lubricants ...................... .499Fog Lights
......................... .93, 97, 389
Fog Light Service .......................... .389
Folding Rear Seat ...........................68
Forward Collision Warning ....................204
Freeing A Stuck Vehicle ..................... .424
Front Position Light ........................ .388
Fuel ................................... .494
Additives ............................. .495
Clean Air ............................. .494
Ethanol .............................. .495
Filler Cap (Gas Cap) ..................... .367
Gasoline .............................. .494
Materials Added ........................ .495
Methanol ............................. .495
Octane

Rating ....................... .494, 499
Requirements .......................... .494
Specifications .......................... .499
Tank Capacity .......................... .498
Fuses .................................. .390
Garage Door Opener (HomeLink) ............134, 139
Gas Cap (Fuel Filler Cap) .....................367
Gasoline, Clean Air ........................ .494
Gasoline (Fuel) ........................... .494
Gasoline, Reformulated ..................... .494
598 INDEX

Glass Cleaning........................... .490
GVWR ................................. .370
Hazard Driving Through Flowing, Rising, Or Shallow
Standing Water ......................... .375
Hazard Warning Flasher ..................... .378
Headlights Bulb Replacement ....................... .386
Cleaning .............................. .486
Delay ..................................93
High Beam/Low Beam Select Switch ...........93
Lights On Reminder .....................93, 96
Passing ............................. .93, 95
Replacing ............................. .386
Switch .................................93
Time Delay .......................... .93, 96
Washers ................................96
Head Restraints ............................83
Heated Mirrors ......................... .89, 92
High Beam/Low Beam Select (Dimmer) Switch . . .93, 94
Hill Start Assist ........................... .195
HomeLink (Garage Door Opener) ...............134
Hood Prop .............................. .126
Hood Release ............................ .126Hook, Coat
.............................. .144
Inside Rearview Mirror ....................89, 378
Instrument Cluster ..................... .159, 182
Instrument Cluster Display Information Display ...................... .160
Instrument Panel Lens Cleaning ................489
Interior And Instrument Lights ..................98
Interior Appearance Care .....................488
Interior Lights ..............................98
Intermittent Wipers (Delay Wipers) ..............101
Introduction ................................4
Inverter, Power ........................... .147
iPod/USB/MP3 Control ..................... .535
Jack Operation ........................ .400, 461
Jump Starting ............................ .418
KeyFob..................................38 Arm The Alarm ..........................54
Disarm The Alarm ........................54
Pr

ogramming Additional Key Fobs .............53
Remote Battery Replacement .................42
Key Fob Battery Service (Remote Keyless Entry) .....42
12
INDEX 599