garage door opener CHRYSLER PT CRUISER 2005 1.G Owners Manual
[x] Cancel search | Manufacturer: CHRYSLER, Model Year: 2005, Model line: PT CRUISER, Model: CHRYSLER PT CRUISER 2005 1.GPages: 368, PDF Size: 10.02 MB
Page 65 of 368
Electronic Speed Control — If Equipped......102
▫To Activate..........................102
▫To Set At A Desired Speed...............103
▫To Deactivate........................103
▫To Resume Speed.....................103
▫To Vary The Speed Setting...............103
▫Manual Transaxle.....................104
▫To Accelerate For Passing...............104
Garage Door Opener — If Equipped.........105
▫Programming The Universal Transceiver.....106
▫“Rolling Code” Programming............108
▫Canadian Programming/Gate Programming . . 109
▫Operation...........................110▫Reprogramming A Single Button..........110
▫Security............................110
Overhead Console — If Equipped...........111
▫Compass/Temperature Display...........112
▫Automatic Compass Calibration...........113
▫Compass Variance Selection..............113
▫Manual Compass Calibration.............114
▫Outside Temperature...................114
Power Sunroof — If Equipped.............114
▫Express Open Feature..................115
▫Wind Buffeting.......................117
▫Sunroof Maintenance...................117
Electrical Power Outlets..................117
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 65
3
Page 105 of 368
Vehicles equipped with four speed automatic transaxles
may experience a downshift to 3rd gear while climbing
uphill or descending downhill. This downshift to 3rd
gear is necessary to maintain vehicle set speed.
On steep hills a greater speed loss or gain may occur so
it may be preferable to drive without speed control.
GARAGE DOOR OPENER — IF EQUIPPED
NOTE:The HomeLinksystem will be disabled if the
Vehicle Theft Alarm (if equipped) is in the Prearmed,
Armed or Alarming state. The HomeLinksystem will
only operate when the Vehicle Theft Alarm (if equipped)
is in the Disarmed mode.
The HomeLinkUniversal Transceiver replaces up to
three remote controls (hand held transmitters) that oper-
ate devices such as garage door openers, motorized
gates, or home lighting. It triggers these devices at thepush of a button. The Universal Transceiver operates off
your vehicle’s battery and charging system; no batteries
are needed.
For additional information on HomeLink, call 1–800–
355–3515, or on the internet at www.homelink.com.
HomeLink Buttons
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 105
3
Page 106 of 368
WARNING!
A moving garage door can cause injury to people and
pets in the path of the door. People or pets could be
seriously or fatally injured. Only use this transceiver
with a garage door opener that has a “stop and
reverse” feature as required by federal safety stan-
dards. This includes most garage door opener mod-
els manufactured after 1982. Do not use a garage
door opener without these safety features it could
cause injury or death. Call toll-free 1–800–355–3515
or, on the Internet at www.homelink.com for safety
information or assistance.
Programming The Universal Transceiver
For best results, install a new battery in the hand held
transmitter before programming. If your garage door
opener (located in the garage) is equipped with an
antenna, make sure that the antenna is hanging straight
down.
1. Turn off the engine.
WARNING!
Vehicle exhaust contains carbon monoxide, a danger-
ous gas. Do not run the vehicle’s exhaust while
training the transceiver. Exhaust gas can cause seri-
ous injury or death.
106 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
Page 107 of 368
WARNING!
Your motorized door or gate will open and close
while you are training the Universal Transceiver. Do
not train the transceiver if people or pets are in the
path of the door or gate. A moving door or gate can
cause serious injury or death to people and pets or
damage to objects.
2. Erase the factory test codes by pressing the two
outside buttons. Release the buttons when the light in the
Universal Transceiver begins to flash (about 20 seconds).
NOTE:Step 2 does not have to be followed to program
additional hand held transmitters.
3. Choose one of the three Universal Transceiver buttons
to program. Place the hand held controller one to three
inches from the Universal Transceiver while keeping its
indicator light in view.4. Using both hands, press the hand held transmitter
button and the desired Universal Transceiver button. Do
not release the buttons until step 5 has been completed.
NOTE:Some entry gates and garage door openers may
require you to replace step 4 with the procedures listed
under Canadian Programming.
HomeLink Programming
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 107
3
Page 108 of 368
5. The indicator light in the Universal Transceiver will
begin to flash, first slowly and then rapidly. The rapid
flashing indicates successful programming. If after 90
seconds the indicator light does not flash rapidly or goes
out, return to step 1 and repeat the procedure. To train the
other buttons, repeat steps 3 and 4. Be sure to keep your
hand held transmitters in case you need to retrain the
Universal Transceiver.
NOTE: If you do not successfully program the Uni-
versal Transceiver to learn the signal of your hand held
transmitter, refer to the Rolling Code Paragraph, or call
toll free for customer assistance at 1–800–355–3515, or
on the internet at www.homelink.com.
“Rolling Code” Programming
NOTE:If your hand held transmitter appears to pro-
gram the Universal Transceiver, but your garage door or
other device does not operate, and your device wasmanufactured after 1996, your garage door opener or
other device may have a “Rolling Code” system.
On garage door openers with the “Rolling Code” feature,
the transmitter code changes after each use to prevent the
copying of your code.
To check if your device is protected by a “Rolling Code”
system:
•Check the owner’s manual for the device for mention
of “Rolling Codes”.
•Press and hold the programmed button on the Univer-
sal Transceiver. If the Universal Transceiver indicator
light flashes rapidly and then stays on after 2 seconds,
the device has the “Rolling Code” feature.
To train a garage door opener (or other rolling code
equipped devices) with the rolling code feature, follow
these instructionsaftercompleting theProgramming
portion of this text:
108 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
Page 109 of 368
NOTE:The assistance of a second person may make the
following programming procedure quicker and easier.
1. Locate the training button on the garage door motor
head unit. The exact location and color of the button may
vary by garage door opener manufacturer. If you have
difficulty in locating the training button, check your
garage door opener manual, or call 1-800-355-3515 or, on
the Internet, at www.homelink.com.
2. Press and hold the training button on the garage door
opener head unit. This will activate the “training” light.
NOTE:After completing step 2, you have 30 seconds to
start step 3.
3. Return to the Universal Transceiver in the vehicle and
firmly press and release the garage door button. Press
and release the button a second time to complete thetraining process. Some garage door openers may require
you to do this procedure a third time to complete the
training.
Your garage door opener should now recognize your
Universal Transceiver. The remaining two buttons may
now be programmed if this has not previously been
done. Refer to the Programming instructions. You may
use either your Universal Transceiver or your original
hand-held transmitter to open you garage door.
Canadian Programming/Gate Programming
Canadian frequency laws, and the technology of some
entry gates, require you to press and release the hand
held transmitter button every two seconds during pro-
gramming.
Continue to press and hold the Universal Transceiver
button while you press and release the hand held trans-
mitter button until the frequency signal has been learned.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 109
3
Page 110 of 368
The Universal Transceiver light will flash slowly and
then rapidly when the programming is successful.
NOTE:When programming such a garage door opener
or gate, unplug the device to prevent possible damage to
the garage door or gate motor.
Operation
Press and hold the desired button on the Universal
Transceiver until the garage door or other device begins
to operate. The light in the display shows that the signal
is being transmitted. The hand held transmitter may also
be used at any time.
Reprogramming A Single Button
1. Press and hold the Universal Transceiver button to be
reprogrammed. Do not release until step 4 has been
completed.2. When the indicator light begins to flash slowly (after
20 seconds) position the hand held transmitter one to
three inches away from the button to be trained.
3. Press and hold the hand held transmitter button.
4. The Universal Transceiver indicator light will begin to
flash, first slowly, then rapidly. When the indicator lights
begin to flash rapidly, release both buttons.
Security
If you sell your vehicle, be sure to erase the frequencies.
To erase all of the previously trained frequencies, hold
down both outside buttons until the indicator light
begins to flash.
110 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
Page 353 of 368
Inspection........................... 287
Points to Remember.................286,288
Pressure Cap......................... 286
Selection of Coolant.................... 285
Corrosion Protection..................... 297
Crankcase Emission Control System.......... 276
Cruise Light........................... 141
Cup Holder............................ 120
Customer Assistance..................... 340
Dealer Service.......................... 268
Defroster, Rear Window................... 190
Defroster, Windshield...................62,185
Delay (Intermittent) Wipers................. 100
Diagnostic System, Onboard................ 266
Dimmer Switch, Headlight.................. 98
Disposal
Antifreeze (Engine Coolant)............... 287
Engine Oil........................... 273Door Ajar............................. 141
Door Locks............................. 18
Door Locks, Automatic.................... 20
Door Opener, Garage..................... 105
Downshifting.......................... 208
Drive Belts............................ 273
Driving
On Slippery Surfaces.................... 256
Electric Rear Window Defrost............... 190
Electric Remote Mirrors.................... 69
Electrical Power Outlets................... 117
Electronic Power Distribution Center.......... 303
Electronic Speed Control................... 102
Emergency, In Case of
Jacking............................. 248
Jump Starting......................... 254
Towing............................. 258
Emergency Trunk Release................... 29
INDEX 353
10
Page 355 of 368
Fuel..............................235,312
Adding............................. 239
Additives............................ 237
Capacity............................ 311
Clean Air............................ 236
Filler Cap.........................143,239
Filler Door........................... 143
Filter............................... 276
Gasoline............................ 235
Gauge.............................. 137
Hoses.............................. 289
Light............................... 143
Octane Rating........................ 235
Requirements......................... 235
System Hoses......................... 289
Tank Capacity........................ 311
Fueling............................... 239
Fuses................................ 303Garage Door Opener..................... 105
GasCap .............................. 239
Gasoline...........................235,311
Gasoline, Clean Air...................... 236
Gasoline, Reformulated................... 236
Gauges
Coolant Temperature.................... 138
Fuel................................ 137
Tachometer.......................... 139
Gearshift.............................. 201
General Information....................17,24
General Maintenance..................... 269
Glass Cleaning.......................... 302
Hands-Free Phone........................ 70
Hazard Warning Flasher................... 246
Head Restraints.......................... 85
INDEX 355
10
Page 359 of 368
Vanity............................... 70
Modifications/Alterations, Vehicle............. 7
Mopar Parts.........................268,345
Multi-Function Control Lever................ 96
Navigation System....................... 177
New Vehicle Break-In Period................ 60
Occupant Restraints....................... 33
Octane Rating, Gasoline................... 235
Odometer............................. 141
Trip .............................141,144
Oil, Engine.........................269,311
Capacity............................ 311
Change Interval....................... 270
Checking............................ 269
Disposal............................ 273
Filter............................... 273
Identification Logo..................... 272Materials Added to..................... 273
Quality............................. 272
Recommendation....................272,311
Synthetic............................ 272
Viscosity............................ 272
Oil Pressure Light....................... 137
Onboard Diagnostic System..............266,267
Opener, Garage Door..................... 105
Operator Manuals (Owner’s Manuals)........... 4
Outside Air Intake....................... 189
Overdrive............................. 203
Overhead Console....................... 111
Overhead Travel Information Center.......... 111
Overheating, Engine...................... 246
Owner’s Manual.......................4,346
Paint Care............................. 297
Panel Rear Shelf........................ 122
Panic Alarm............................ 23
INDEX 359
10