hood release CHRYSLER PT CRUISER 2005 1.G Owners Manual
[x] Cancel search | Manufacturer: CHRYSLER, Model Year: 2005, Model line: PT CRUISER, Model: CHRYSLER PT CRUISER 2005 1.GPages: 360, PDF Size: 11.21 MB
Page 93 of 360
TO OPEN AND CLOSE THE HOOD
To open the hood, two latches must be released. First pull
the hood release lever located under the left side of the
instrument panel.Then move the safety catch located under the front edge
of the hood, near the center and slightly to the right, and
raise the hood.
Use the hood prop rod clipped to the driver’s side of the
engine compartment to secure the hood in the open
position. Place the hood prop at the location stamped into
the inner hood surface.
To prevent possible damage, do not slam the hood to
close it. Lower the hood until it is open approximately 20
cm (8 inches) and then drop it. This should secure both
latches. Never drive your vehicle unless the hood is fully
closed, with both latches engaged.
Hood Release Lever
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 93
3
Page 242 of 360
WARNING!
Battery fluid is a corrosive acid solution; do not
allow battery fluid to contact eyes, skin or clothing.
Don’t lean over battery when attaching clamps or
allow the clamps to touch each other. If acid splashes
in eyes or on skin, flush the contaminated area
immediately with large quantities of water.
A battery generates hydrogen gas which is flam-
mable and explosive. Keep flame or spark away
from the vent holes. Do not use a booster battery or
any other booster source with an output that exceeds
12 volts.
5. Connect the other cable, first to the negative terminal
of the booster battery and then to the negative jump start
terminal, located near the hood release latch, of the
vehicle with the discharged battery. Make sure you have
a good contact.6. Turn the ignition switch to the ON position for 3
seconds before moving the ignition switch to the START
position.
7. Start the engine in the vehicle that has the booster
battery, let the engine idle a few minutes, then start the
engine in the vehicle with the discharged battery.
Negative Jump Start
242 WHAT TO DO IN EMERGENCIES
Page 269 of 360
Body Lubrication
Locks and all body pivot points, including such items as
seat tracks, doors, deck lid and hood hinges, should be
lubricated periodically to assure quiet, easy operation
and to protect against rust and wear. Prior to the appli-
cation of any lubricant, the parts concerned should be
wiped clean to remove dust and grit; after lubricating
excess oil and grease should be removed. Particular
attention should also be given to hood latching compo-
nents to insure proper function. When performing other
underhood services, the hood latch, release mechanism
and safety catch should be cleaned and lubricated.
The external lock cylinders should be lubricated twice a
year, preferably in the fall and spring. Apply a small
amount of a high quality lubricant such as MoparLock
Cylinder Lubricant directly into the lock cylinder.
Windshield Wiper Blades
Clean the rubber edges of the wiper blades and the
windshield periodically with a sponge or soft cloth and a
mild non abrasive cleaner or use the washer solvent. This
will remove accumulations of salt, waxes or road film
and help reduce streaking and smearing.
Operation of the wipers on dry glass for long periods
may cause deterioration of the wiper blades. Always use
washer fluid when using the wipers to remove salt or dirt
from a dry windshield. Avoid using the wiper blades to
remove frost or ice from the windshield. make sure that
they are not frozen to the glass before turning them on to
avoid damaging the blade. Keep the blade rubber out of
contact with petroleum products such as engine oil,
gasoline, etc.
Windshield Wiper Blade Replacement
1. Lift the wiper arm away from the glass.
MAINTAINING YOUR VEHICLE 269
7
Page 346 of 360
High Beam.........................97,129
High Beam/Low Beam Select Switch......... 97
Passing.............................. 97
Switch............................... 96
Heated Seats............................ 86
Homelink Transmitter.................... 106
Hood Release........................... 93
Hoses................................ 277
Ignition............................... 12
Key ................................. 12
Wiring System........................ 262
Immobilizer..........................14,26
Indicator, Traction Control...............131,132
Infant Restraint.......................... 50
Inside Rearview Mirror.................... 75
Instrument Cluster....................124,127
Instrument Panel and Controls.............. 123
Instrument Panel Cover................... 289Instrument Panel Lens Cleaning............. 289
Integrated Power Module.................. 292
Interior Appearance Care.................. 288
Interior Fuses.......................... 295
Interior Lights........................... 94
Intermittent Wipers....................... 99
Introduction............................. 4
Jack Location........................... 235
Jack Operation.......................235,238
Jump Starting.......................... 240
Key, Programming........................ 16
Key Release Button....................... 13
Key, Replacement........................ 16
Key, Sentry............................. 14
Key-In Reminder......................... 14
Keyless Entry System...................... 21
Keys................................. 12
346 INDEX