wiring CHRYSLER PT CRUISER 2005 1.G Owners Manual

The front airbag system consists of the following:
•Airbag Control Module (ACM)
•AIRBAG Readiness Light
•Driver and Passenger Front Airbag/Inflator Units
•Unique Steering Wheel and Column
•Unique Instrument Panel
•Interconnecting Wiring
•Seat Belt Pretensioners
•Knee Impact Bolster
The Side Airbag System, on vehicles equipped, consists
of the following:
•AIRBAG Readiness Light (shared with the front airbag
system)
•Side Airbag in the driver’s seat
•Side Airbag in the passenger’s seat
•Airbag Control Module (shared with the front airbag
system)
•Side impact sensors
•Interconnecting Wiring
How The Front Airbag System Works
•
The airbag control module determines if a frontal
impact is severe enough to require the airbags to
inflate. The control module will not detect, roll over, or
rear collisions. The airbag control module will only
detect side collisions if the vehicle is so equipped with
side airbags.
The airbag control module also monitors the readiness
of the electronic parts of the system whenever the
ignition switch is in the START or ON positions. These
include all of the items listed above except the knee
44 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

Maintaining Your Airbag System
WARNING!
•Modifications to any part of the airbag system
could cause it to fail when you need it. You could
be injured because the airbags are not there to
protect you. Do not modify the components or
wiring, including adding any kind of badges or
stickers to the steering wheel hub trim cover or
the upper right side of the instrument panel. Do
not modify the front bumper, vehicle body struc-
ture, or frame.
•You need proper knee impact protection in a
collision. Do not mount or locate any aftermarket
equipment on or behind the knee bolsters.
•It is dangerous to try to repair any part of the
airbag system yourself. Be sure to tell anyone who
works on your vehicle that it has airbags.
Airbag Light
You will want to have the airbags ready to inflate for your
protection in a collision. While the airbag system is
designed to be maintenance free, if any of the following
occurs, have an authorized dealer service the system
immediately.
•The AIRBAG light does not come on or flickers during
the 6 to 8 seconds when the ignition switch is first
turned on.
•The light remains on or flickers after the 6 to 8 second
interval.
•The light flickers or comes on and remains on while
driving.
48 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

MAINTAINING YOUR VEHICLE
CONTENTS

2.4L Turbo Engine Compartment............252

2.4L Engine Compartment................253

Onboard Diagnostic System—OBDII........254

Emissions Inspection And Maintenance
Programs............................255

Replacement Parts......................256

Dealer Service.........................256

Maintenance Procedures..................257
▫Engine Oil..........................257▫Drive Belts—Check Condition And Tension . . 261
▫Spark Plugs.........................262
▫Ignition Wiring System.................262
▫Catalytic Converter....................262
▫Engine Timing Belt....................264
▫Crankcase Emission Control System........264
▫Fuel Filter..........................264
▫Air Cleaner Element (Filter)..............264
▫Maintenance-Free Battery................265
7

Special tools are required to properly measure tension
and to restore belt tension to factory specifications. Also,
check belt routing to make sure there is no interference
between the belts and other engine components.
Spark Plugs
Spark plugs must fire properly to assure engine perfor-
mance and emission control. New plugs should be in-
stalled at the specified mileage. The entire set should be
replaced if there is any malfunction due to a faulty spark
plug. Refer to the Engine data Label located under the
hood for the proper type of spark plug for use in your
vehicle.
Ignition Wiring System
The ignition cables should be kept clean and properly
connected. Terminals should be fully seated. Cracked,
damaged, or faulty cables should be replaced.
Catalytic Converter
The catalytic converter requires the use of unleaded fuel
only. Leaded gasoline will destroy the effectiveness of the
catalyst as an emission control device.
Under normal operating conditions, the catalytic con-
verter will not require maintenance. However, it is im-
portant to keep the engine properly tuned to assure
proper catalyst operation and prevent possible catalyst
damage.
262 MAINTAINING YOUR VEHICLE

High Beam.........................97,129
High Beam/Low Beam Select Switch......... 97
Passing.............................. 97
Switch............................... 96
Heated Seats............................ 86
Homelink Transmitter.................... 106
Hood Release........................... 93
Hoses................................ 277
Ignition............................... 12
Key ................................. 12
Wiring System........................ 262
Immobilizer..........................14,26
Indicator, Traction Control...............131,132
Infant Restraint.......................... 50
Inside Rearview Mirror.................... 75
Instrument Cluster....................124,127
Instrument Panel and Controls.............. 123
Instrument Panel Cover................... 289Instrument Panel Lens Cleaning............. 289
Integrated Power Module.................. 292
Interior Appearance Care.................. 288
Interior Fuses.......................... 295
Interior Lights........................... 94
Intermittent Wipers....................... 99
Introduction............................. 4
Jack Location........................... 235
Jack Operation.......................235,238
Jump Starting.......................... 240
Key, Programming........................ 16
Key Release Button....................... 13
Key, Replacement........................ 16
Key, Sentry............................. 14
Key-In Reminder......................... 14
Keyless Entry System...................... 21
Keys................................. 12
346 INDEX