light CHRYSLER SEBRING CONVERTIBLE 2008 3.G Owners Manual

BULB REPLACEMENT
Low Beam Headlight, High Beam Headlight
1. Open the hood.
NOTE:It may be necessary to remove the air cleaner
filter housing and position the totally integrated power
module aside prior to replacing the low beam headlight
on the driver's side of the vehicle.
2. Rotate the applicable bulb and connector assembly
1¤4
turn counterclockwise and remove the assembly from the
headlight housing.
3. Disconnect the bulb from the harness connector and
then connect the replacement bulb.
1 Ð High Beam Headlight
2 Ð Low Beam HeadlightMAINTAINING YOUR VEHICLE 4017

CAUTION!
Do not touch the new bulb with your fingers. Oil
contamination will severely shorten bulb life. If the
bulb comes in contact with any oily surface, clean the
bulb with rubbing alcohol.
4. Install the bulb and connector assembly into the
headlight housing and rotate it
1¤4turn clockwise to lock
it in place.
Front Turn Signal/Park Light
1. Open the hood.
2. Rotate the bulb's electrical connector
1¤4turn counter-
clockwise and remove it from the headlight housing.
Front Turn Signal/Park Light
402 MAINTAINING YOUR VEHICLE

3. Remove the bulb from the connector socket and install
the replacement bulb.
4. Install the bulb and connector assembly into the
headlight housing and rotate the connector
1¤4turn clock-
wise to lock it in place.
Front Fog Light
NOTE:Access to the lights through the lower fascia
cutout is limited. We recommend you access the lights by
turning the steering wheel to allow access and remove
the inner fender shield.
1. Rotate the bulb's electrical connector
1¤4turn counter-
clockwise and remove it from the fog light housing.Front Fog Light
MAINTAINING YOUR VEHICLE 403
7

2. Remove the bulb from the connector socket and install
the replacement bulb.
CAUTION!
Do not touch the new bulb with your fingers. Oil
contamination will severely shorten bulb life. If the
bulb comes in contact with an oily surface, clean the
bulb with rubbing alcohol.
3. Install the bulb and connector assembly into the fog
light housing and rotate the connector
1¤4turn clockwise
to lock it in place.
Tail/Stop Light, Rear Turn Signal Light, Backup
Light
The taillights are a two-piece design. The tail/stop lights
and rear turn signal lights are located in the rear corner
body panels. The backup lights and rear fog lights are
located in the trunk lid.
Changing the Tail/Stop Light or Rear Turn Signal
Light
1. Open the trunk.
404 MAINTAINING YOUR VEHICLE

2. Remove the two plastic wing nuts from the taillight
housing.
3. Grasp the taillight housing with one hand on the
bottom of the housing and the other hand on the inboard
housing flange and pull it outward firmly to disengage
the housing from the vehicle.4. Rotate the applicable bulb's electrical connector1¤4
turn counterclockwise and remove it from the taillight
housing.
Location Plastic Wing Nuts
1 Ð Tail/Stop Light
2 Ð Turn Signal LightMAINTAINING YOUR VEHICLE 405
7

5. Remove the bulb from the connector socket and install
the replacement bulb.
6. Install the bulb and connector assembly into the
taillight housing and rotate the connector
1¤4turn clock-
wise to lock it in place.
7. Reinstall the taillight housing.
Changing the Backup Light
1. Open the trunk.
2. Rotate the bulb's electrical connector
1¤4turn counter-
clockwise and remove it from the housing.
3. Remove the bulb from the connector socket and install
the replacement bulb.
4. Install the bulb and connector assembly into the
housing and rotate the connector
1¤4turn clockwise to
lock it in place.
Backup and Rear Fog Light
406 MAINTAINING YOUR VEHICLE

License Plate Light
1. Remove the two retaining screws from the lens.2. Gently pry the lens loose.
3. Remove the bulb from the connector socket and install
the replacement bulb.
4. Install the lens and the two retaining screws.
Location and Removal of Rear License Light Lens
MAINTAINING YOUR VEHICLE 407
7

Center High-Mounted Stop Light (CHMSL)
1. Open the trunk lid.
2. Rotate the bulb's electrical connector
1¤4turn counter-
clockwise and remove it from the CHMSL housing.3. Disconnect the bulb from the harness connector and
then connect the replacement bulb.
4. Install the bulb and connector assembly into the
CHMSL housing and rotate the connector1¤4turn clock-
wise to lock it in place.
High-mounted Stop Light Bulb Replacement
408 MAINTAINING YOUR VEHICLE

Once a Month
²Check tire pressure and look for unusual wear or
damage.
²Inspect the battery and clean and tighten the terminals
as required.
²Check the fluid levels of coolant reservoir, brake
master cylinder, power steering, and automatic trans-
axle, and add fluid as needed.
NOTE:Six speed AutoSticktTransaxle Ð if equipped is
sealed, therefore checking the fluid level can only be
done by a certified dealership service center.
²Check all lights and other electrical items for correct
operation.At Each Oil Change
²Change the engine oil filter.
²Inspect the brake hoses and lines.
CAUTION!
Failure to perform the required maintenance items
may result in damage to the vehicle.
416 MAINTENANCE SCHEDULES
8
M
A
I
N
T
E
N
A
N
C
E
S
C
H
E
D
U
L
E
S

Customer Assistance For The Hearing Or Speech
Impaired (TDD/TTY)
To assist customers who have hearing difficulties, the
manufacturer has installed special TDD (Telecommuni-
cation Devices for the Deaf) equipment at its Customer
Center. Any hearing or speech impaired customer who
has access to a TDD or a conventional teletypewriter
(TTY) in the United States can communicate with the
manufacturer by dialing 1±800±380±CHRY.
Service Contract
You may have purchased a service contract for your
vehicle to help protect you from the high cost of unex-
pected repairs after your manufacturer's new vehicle
limited warranty expires. The manufacturer stands be-
hind only the manufacturer's Service Contracts. If you
purchased a manufacturer's Service Contract, you will
receive Plan Provisions and an Owner Identification Card
in the mail within three weeks of your vehicle delivery
date. If you have any questions about your servicecontract, call the manufacturer's Service Contract Na-
tional Customer Hotline at 1-800-521-9922.
The manufacturer will not stand behind any service
contract that is not the manufacturer's Service Contract. It
is not responsible for any service contract other than the
manufacturer's Service Contract. If you purchased a
service contract that is not a manufacturer's Service
Contract, and you require service after your manufactur-
er's new vehicle limited warranty expires, please refer to
your contract documents, and contact the person listed in
those documents.
We appreciate that you have made a major investment
when you purchased your vehicle. Your authorized
dealer has also made a major investment in facilities,
tools, and training to assure that you are absolutely
delighted with your ownership experience. You'll be
pleased with their sincere efforts to resolve any warranty
issues or related concerns.
IF YOU NEED CONSUMER ASSISTANCE 425
9