buttons CHRYSLER SEBRING SEDAN 2007 3.G Owners Manual
[x] Cancel search | Manufacturer: CHRYSLER, Model Year: 2007, Model line: SEBRING SEDAN, Model: CHRYSLER SEBRING SEDAN 2007 3.GPages: 376
Page 18 of 376
1. Press and hold the LOCK button on a programmed
key fob.
2. Continue to hold the LOCK button at least 4 seconds,
but not longer than 10 seconds, then press and hold the
UNLOCK button. A single chime will sound to indicate
that this feature has changed.
3. Release both buttons at the same time.
4. Test the feature while outside of the vehicle, by
pressing the LOCK/UNLOCK button on the keyfob.
NOTE:Pressing the LOCK button on the keyfob while
you are inside the vehicle will activate the Security
Alarm. Opening a door with the Security Alarm activated
will cause the alarm to sound. Press the UNLOCK button
to deactivate the Security Alarm.
5. If the desired programming was not achieved or to
reactivate this feature, repeat the above steps.
To lock the doors:
Press and release the LOCK button on the transmitter to
lock all doors. The turn signal lights will flash and the
horn will chip once to acknowledge the lock signal. If
desired, the “Sound Horn On Lock” feature can be
turned on or off. On electronic vehicle information center
(EVIC) equipped vehicles refer to “Personal Settings” in
the “Electronic Vehicle Information Center (EVIC)” sec-
tion of this manual. On non EVIC – equipped vehicles
perform the following steps:
1. Press the LOCK button for 4 to 10 seconds.
2. While the LOCK button is pressed (after 4 seconds),
press the PANIC button. Release both buttons.
The “Sound Horn On Lock” feature can be reactivated by
repeating this procedure.
To Unlatch the Trunk:
Press the trunk button on the transmitter two times to
unlatch the trunk.
18 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE
Page 19 of 376
Using The Express Down Window Feature — If
Equipped
The key fob remotely lowers both driver and passenger
front windows simultaneously. Lowering the front win-
dows using the key fob is a two step operation:
1. Press theunlockbutton once.
2. Press theunlockbutton a second time and hold the
button until the glass lowers completely or the windows
drop to the desired level
Using The Panic Alarm:
To turn the panic alarm feature ON or OFF, press and
hold the PANIC button on the transmitter for at least one
second and release. When the panic alarm is on, the
headlights and park lights will flash, the horn will pulse
on and off and the interior lights will turn on.
The panic alarm will stay on for 3 minutes unless you
turn it off by pressing the PANIC button a second time or
if the vehicle speed is 5 mph (8 km/h) or greater.
NOTE:When you turn off the panic alarm by pressing
the PANIC button a second time, you may have to be
closer to the vehicle due to the radio frequency noises of
the system.
To Turn Off “Flash Lights With Lock”
NOTE:
The “Flash Lights With Lock” feature can be
turned on or off. On electronic vehicle information center
(EVIC) equipped vehicles refer toPersonal Settingsin
the EVIC section of this manual. On non EVIC - equipped
vehicles perform the following steps:
1. Press the UNLOCK button for 4 to 10 seconds.
2. While the UNLOCK button is pressed, (after 4 sec-
onds) press the LOCK button. Release both buttons.
3. Test the flash lamps with LOCK feature while outside
of the vehicle, by pressing the LOCK button on the key
fob with the ignition in the LOCK position, and the key
removed.
The “Flash Lights On Lock/Unlock” feature can be
reactivated by repeating this procedure.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 19
2
Page 20 of 376
NOTE:Pressing the LOCK button on the key fob, while
you are in the vehicle, will activate the Security Alarm.
Opening a door with the Security Alarm activated will
cause the alarm to sound. Press the UNLOCK button to
deactivate the Security Alarm.
To Program Transmitters:
Refer to SENTRY KEY “Sentry Key Programming.”
If you do not have a programmed transmitter, contact
your dealer for details.
General Information
This device complies with part 15 of FCC rules and with
RS-210 of Industry Canada. Operation is subject to the
following conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference that may be
received including interference that may cause undesired
operation.
NOTE:Changes or modifications not expressly ap-
proved by the party responsible for compliance could
void the user’s authority to operate the equipment.
If your Remote Lock Control fails to operate from a
normal distance, check for these two conditions.
1. Weak batteries in transmitter. The expected life of
batteries is five years.
2. Closeness to a radio transmitter such as a radio station
tower, airport transmitter, military base, and some mobile
or CB radios.
Battery Replacement
The recommended replacement battery is CR2032.
1. With the transmitter buttons facing down, use a flat
blade to pry the two halves of the transmitter apart. Make
sure not to damage the seal during removal.
20 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE
Page 69 of 376
▫Programming A “Rolling Code” System.....117
▫Canadian Programming/Gate Programming . . 118
▫Using HomeLink.....................118
▫Erasing HomeLink Buttons..............118
▫Reprogramming a Single HomeLink Button . . . 119
▫Security............................119
Power Sunroof — If Equipped............121
▫Opening Sunroof - Manual..............122
▫Opening Sunroof - Express..............122
▫Closing Sunroof - Manual...............122
▫Venting Sunroof - Express...............122
▫Closing Sunroof - Express...............122
▫Auto Sunroof (Express) With Anti–Pinch
Protection — If Equipped...............122
▫Sunshade Operation...................123▫Wind Buffeting.......................123
▫Sunroof Maintenance...................123
▫Ignition Off Operation..................123
Electrical Power Outlets.................124
▫Electrical Power Inverter — If Equipped.....125
▫Electrical Outlet Use With Engine Off.......126
Cigar Lighter And Ash Receiver...........126
▫Cup Holder Ash Receiver — If Equipped....126
Console Features......................128
▫Console Features......................128
Cup Holders.........................130
▫Heated Or Cooled Cup Holder —
If Equipped.........................130
▫Rear Bottle Holders....................131
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 69
3
Page 74 of 376
The UConnect™ phone book enables you to store up to
32 names and four numbers per name. Each language has
a separate 32-name phone book accessible only in that
language. This system is driven through your Blue-
tooth™ Hands-Free profile cellular phone. UConnect™
features Bluetooth™ technology - the global standard
that enables different electronic devices to connect to
each other without wires or a docking station, so UCon-
nect works no matter where you stow your cellular
phone (be it your purse, pocket, or briefcase), as long as
your phone is turned on and has been paired to the
vehicle’s UConnect™ system. The UConnect™ system
allows up to seven cellular phones to be linked to system.
Only one linked (or paired) cellular phone can be used
with the system at a time. The system is available in
English, Spanish, or French languages (as equipped).The rearview mirror contains the microphone for the
system and the radio has the two control buttons that will
enable you to access the system. Actual button location
may vary with radio. The individual buttons are de-
scribed in the “Operations” section.
Microphone Location
74 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
Page 75 of 376
The UConnect™ system can be used with any Hands-
Free Profile certified Bluetooth™ cellular phone. See
www.chrysler.com/uconnect for supported phones. If
your cellular phone supports a different profile (e.g.,
Headset Profile) you may not be able to use any UCon-
nect™ features. Refer to your cellular service provider or
the phone manufacturer for details.
The UConnect™ system is fully integrated with the
vehicle’s audio system. The volume of the UConnect™system can be adjusted either from the radio volume
control knob or from the steering wheel radio control
(right switch), if so equipped.
The radio display will be used for visual prompts from
the UConnect™ system such asCELLor caller ID on
certain radios.
Operations
Voice commands can be used to operate the UConnect™
system and to navigate through the UConnect™ menu
structure. Voice commands are required after most
UConnect™ system prompts. You will be prompted for a
specific command and then guided through the available
options.
•Prior to giving a voice command, one must wait for
the beep, which follows theReadyprompt or another
prompt.
•For certain operations, compound commands can be
used. For example, instead of sayingSetupand then
Phone Pairing,the following compound command
can be said:Setup Phone Pairing.
UConnect Buttons
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 75
3
Page 115 of 376
To Accelerate For Passing:
Depress the accelerator as you would normally. When the
pedal is released, the vehicle will return to the set speed.
Using Speed Control On Hills
NOTE:
The speed control system maintains speed up
and down hills. A slight speed change on moderate hills
is normal.
On steep hills, a greater speed loss or gain may occur so
it may be preferable to drive without speed control.
GARAGE DOOR OPENER (HomeLink)—IF
EQUIPPED
The HomeLinkUniversal Transceiver replaces up to
three remote controls (hand held transmitters) that oper-
ate devices such as garage door openers, motorized
gates, or home lighting. It triggers these devices at the
push of a button. The Universal Transceiver operates off
your vehicle’s battery and charging system; no batteries
are needed.
NOTE:The HomeLinkUniversal Transceiver is dis-
abled when the Vehicle Security Alarm is active.For additional information on HomeLink, call 1–800–
355–3515, or on the internet at www.homelink.com.
The three buttons for your garage door opener will be
located in the driver’s sunvisor. The training procedure is
the same regardless of the 3-button location.
Programming The Universal Transceiver
(HomeLink)
NOTE:
When programming a garage door opener, it is
advised to park outside the garage and with the engine
off. It is also recommended that you install a new battery
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 115
3
Page 116 of 376
in the hand-held transmitter of the device being pro-
grammed. This will allow for quicker training and accu-
rate transmission of the radio-frequency signal.
If your garage door opener (located in the garage) is
equipped with an antenna, make sure that the antenna is
hanging straight down.
1. Erase the factory test codes by pressing the two
outside buttons. Release the buttons when the light in the
Universal Transceiver begins to flash (about 20 seconds).
NOTE:Step 1 above does not have to be followed to
program additional hand held transmitters.
2. Choose one of the three Universal Transceiver buttons
to program. Position the end of your hand-held transmit-
ter 1-3 inches (3-8 cm) away from the HomeLink buttons
while keeping its indicator light in view.3. Simultaneously press and hold the HomeLink button
(that you want to train) and the hand-held transmitter
button.Do not release the buttons until Step 4 is
complete.
NOTE:Some gate operators and garage door openers
may require you to replace this Programming Step 3 with
procedures noted underGate Operator/Canadian Pro-
gramming.
Proper Transceiver Training Distance
116 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
Page 117 of 376
4. The indicator light in the Universal Transceiver will
begin to flash, first slowly and then rapidly. The rapid
flashing indicates successful programming. If after 90
seconds the indicator light does not flash rapidly or goes
out, return to step 1 and repeat the procedure. To train the
other buttons, repeat steps 3 and 4. Be sure to keep your
hand held transmitters in case you need to retrain the
Universal Transceiver.
NOTE:To program the remaining two HomeLink but-
tons, begin withProgrammingStep Two. Do not repeat
Step One.
NOTE:If your garage door opener fails to respond to
the programmed HomeLinkUniversal Transceiver, and
your garage door opener is manufactured after 1995, it
may have a multiple security code system (rolling code
system). If your garage door opener is the “rolling code”
type, please proceed to the heading “Programming A
Rolling Code System.”
Programming A “Rolling Code” System
On garage door openers with the “Rolling Code” feature,
the transmitter code changes after each use to prevent the
copying of your code.
NOTE:The assistance of a second person may make the
following programming procedure quicker and easier.
1. Locate the training button on the garage door motor
head unit. The exact location and color of the button may
vary by garage door opener manufacturer. If you have
difficulty in locating the training button, check your
garage door opener manual, or call 1-800-355-3515 or, on
the Internet, at www.homelink.com.
2. Press and hold the training button on the garage door
opener head unit. This will activate the “training” light.
NOTE:After completing step 2, you have 30 seconds to
start step 3.
3. Return to the Universal Transceiver in the vehicle and
firmly press and release the garage door button. Press
and release the button a second time to complete the
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 117
3
Page 118 of 376
training process. Some garage door openers may require
you to do this procedure a third time to complete the
training.
Canadian Programming/Gate Programming
Canadian radio-frequency laws require transmitter sig-
nals totime-out(or quit) after several seconds of
transmission, which may not be long enough for
HomeLink to pick up the signal during programming.
Similar to this Canadian law, some U.S. gate operators are
designed totime-outin the same manner.
If you live in Canada or you are having difficulties
programming a gate operator by using theProgram-
mingprocedures (regardless of where you live),replace
Programming HomeLinkStep 3with the following:
3. Continue to press and hold the HomeLink button
while youpress and releaseyour hand-held transmitter
every two secondsuntil the frequency signal is accepted
successfully by HomeLink. The Universal Transceiver
light will flash slowly and then rapidly when the pro-
gramming is successful. Proceed withProgramming
HomeLinkStep 4to complete the procedure.
NOTE:When programming such a garage door opener
or gate, unplug the device to prevent possible damage to
the garage door or gate motor.
Using HomeLink
To operate, simply press and release the programmed
HomeLink button. Activation will now occur for the
trained device (i.e. garage door opener, gate operator,
security system, entry door lock, home/office lighting,
etc.). The light in the display shows that the signal is
being transmitted. For convenience, the hand-held trans-
mitter of the device may also be used at any time.
Erasing HomeLink Buttons
To erase programming from the three buttons (individual
buttons cannot be erased but can bereprogrammed-
note below), follow the step noted:
Press and hold the two outer HomeLink buttons (for
approximately 20 seconds). Release the buttons when the
indicator begins to flash rapidly. All three channels will
be cleared.
118 UNDERSTANDING THE FEATURES OF YOUR VEHICLE