hood release CHRYSLER SEBRING SEDAN 2007 3.G Owners Manual
[x] Cancel search | Manufacturer: CHRYSLER, Model Year: 2007, Model line: SEBRING SEDAN, Model: CHRYSLER SEBRING SEDAN 2007 3.GPages: 376
Page 103 of 376
TO OPEN AND CLOSE THE HOOD
To open the hood, two latches must be released. First pull
the hood release lever located under the left side of the
instrument panel.Then lift the secondary latch located under the front edge
of the hood, near the center and raise the hood.
Hood Release Lever
Hood Safety Catch
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 103
3
Page 209 of 376
engine is flooded. Leave the ignition key in the ON
position, release the accelerator pedal and repeat the
“NORMAL STARTING” procedure.
WARNING!
Never pour fuel or other flammable liquid into the
throttle body air inlet opening in an attempt to start
the vehicle. This could result in flash fire causing
serious personal injury.
CAUTION!
To prevent damage to the starter, do not crank the
engine for more than 15 seconds at a time. Wait 10 to
15 seconds before trying again.
After Starting
The idle speed will automatically decrease as the engine
warms up.
Remote Start System — If Equipped
Remote start conveniently starts the engine from outside
the vehicle by using the Remote Keyless Entry (RKE) key
fob while maintaining security. The system has a targeted
range of 328 ft. (100 m). The vehicle must be locked, the
deck lid and hood closed and the transmission in Park in
order to start the engine using the Remote Start button on
the key fob.
NOTE:Remote start requires Automatic Transaxle
equipped vehicles.
How To Use Remote Start
Toenter the Remote Start mode, depress the Remote
Start button twice on the key fob. The engine will start
and the vehicle will remain in the remote start mode for
a 15 minute cycle.
STARTING AND OPERATING 209
5
Page 303 of 376
Body Lubrication
Locks and all body pivot points, including such items as
seat tracks, doors, liftgate and hood hinges, should be
lubricated periodically to assure quiet, easy operation
and to protect against rust and wear. Prior to the appli-
cation of any lubricant, the parts concerned should be
wiped clean to remove dust and grit; after lubricating
excess oil and grease should be removed. Particular
attention should also be given to hood latching compo-
nents to insure proper function. When performing other
underhood services, the hood latch, release mechanism
and safety catch should be cleaned and lubricated.
The external lock cylinders should be lubricated twice a
year, preferably in the fall and spring. Apply a small
amount of a high quality lubricant such as MoparLock
Cylinder Lubricant directly into the lock cylinder.
Windshield Wiper Blades
Clean the rubber edges of the wiper blades and the
windshield periodically with a sponge or soft cloth and a
mild non abrasive cleaner or use the washer solvent. This
will remove accumulations of salt, waxes or road film
and help reduce streaking and smearing.
Operation of the wipers on dry glass for long periods
may cause deterioration of the wiper blades. Always use
washer fluid when using the wipers to remove salt or dirt
from a dry windshield. Avoid using the wiper blades to
remove frost or ice from the windshield. Make sure that
they are not frozen to the glass before turning them on to
avoid damaging the blade. Keep the blade rubber out of
contact with petroleum products such as engine oil,
gasoline, etc.
Windshield Wiper Blade Replacement
1. Lift the wiper arm away from the glass.
2. Push the release tab shown in the illustration and slide
the wiper blade assembly down along the arm. Gently
place the wiper arm on the windshield.
MAINTAINING YOUR VEHICLE 303
7
Page 363 of 376
General Information................. 14,95,248
General Maintenance.................... 293
Glass Cleaning......................... 316
GrossAxleWeightRating ..............259,262
GrossVehicleWeightRating ............259,261
GVWR............................... 259
Hands-Free Phone (UConnect™)............ 73
Hazard Warning Flasher.................. 272
Head Restraints........................ 101
Headlights............................ 322
Bulb Replacement..................... 322
Cleaning............................ 316
High Beam.......................108,145
High Beam/Low Beam Select Switch...... 108
Passing............................. 106
Switch ............................. 105
Heated Seats........................... 99
Hitches
TrailerTowing ....................... 263
HomeLink(Garage Door Opener)
Transmitter........................... 115
Hood Prop............................ 104Hood Release.......................... 103
Hoses............................... 309
Ignition............................... 10
Key ................................ 10
Ignition Key Removal.................... 10
IlluminatedEntry ....................... 16
Immobilizer (Sentry Key).................. 12
InfantRestraint ....................... 54,55
Information Center, Vehicle............... 147
Inside Rearview Mirror................... 70
Instrument Cluster...................137,139
Instrument Panel and Controls............. 136
Instrument Panel Cover.................. 317
Instrument Panel Lens Cleaning............ 316
Integrated Power Module (Fuses)........... 318
Interior Appearance Care................. 315
InteriorLights ......................... 104
Introduction............................ 4
Jack Location.......................... 274
Jack Operation......................274,276
Jacking Instructions..................... 276
INDEX 363
10