windshield wipers CHRYSLER SEBRING SEDAN 2007 3.G Owners Manual
[x] Cancel search | Manufacturer: CHRYSLER, Model Year: 2007, Model line: SEBRING SEDAN, Model: CHRYSLER SEBRING SEDAN 2007 3.GPages: 376
Page 68 of 376
Lights..............................104
▫Map/Reading/Interior Lights............104
▫Multi-Function Control Lever.............105
▫Headlights, Parking Lights, Instrument
Panel Lights.........................105
▫Automatic Headlight System — If Equipped . . 106
▫Headlight Time Delay..................106
▫Passing Light / Flash To Pass.............106
▫Daytime Running Lights (DRL) —
If Equipped.........................107
▫Lights On Reminder...................107
▫Fog Lights — If Equipped...............107
▫Turn Signals.........................108
▫Highbeam/Lowbeam Select Switch.........108
Windshield Wipers And Washers..........109
▫Windshield Washers...................109▫Mist Feature.........................110
▫Windshield Wiper Operation.............111
▫Speed Sensitive Intermittent Wiper System . . . 111
▫Adding Washer Fluid..................111
Tilt/Telescoping Steering Column..........112
Electronic Speed Control — If Equipped.....113
▫ToActivate ..........................113
▫To Set At A Desired Speed...............113
▫To Deactivate........................114
▫To Resume Speed.....................114
▫To Vary The Speed Setting...............114
▫To Accelerate For Passing...............115
Garage Door Opener (HomeLink)—
If Equipped
..........................115
▫Programming The Universal Transceiver
(HomeLink) ........................115
68 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
Page 109 of 376
WINDSHIELD WIPERS AND WASHERS
The wipers and washers are operated by a switch
on the control lever. The lever is located on the
right side of the steering column.
Windshield Washers
To use the washer, pull the multi-function control lever
toward you and hold while spray is desired. If the lever
is pulled while in the delay range, the wiper will operate
in low speed for two wipe cycles after the lever is
released, and then resume the intermittent interval pre-
viously selected.
If the lever is pulled while in the OFF position, the wipers
will operate for two wipe cycles, then turn OFF.
NOTE:Always remove any buildup of snow that
prevents the windshield wiper blades from returning to
the OFF position. If the windshield wiper switch is
turned OFF and the blades cannot return to the OFF
position, damage to the wiper motor may occur.
Windshield Wiper / Washer Lever
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 109
3
Page 110 of 376
Mist Feature
Push down on the wiper control lever to activate a single
wipe to clear the windshield of road mist or spray from
a passing vehicle. As long as the lever is held down, the
wipers will continue to operate.WARNING!
Sudden loss of visibility through the windshield
could lead to an accident. You might not see other
vehicles or other obstacles. To avoid sudden icing of
the windshield during freezing weather, warm the
windshield with defroster before and during wind-
shield washer use.
Mist Control
110 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
Page 111 of 376
Windshield Wiper Operation
Turn to the second detent for low wiper speed and the
third detent for high wiper speed.
Speed Sensitive Intermittent Wiper System
Use the intermittent wiper when weather conditions
make a single wiping cycle, with a variable pause be-
tween cycles, desirable. Select the delay interval by
turning the end of the lever. Rotate the knob upward to
decrease the delay time and downward to increase thedelay time. The delay can be regulated from a maximum
of approximately 18 seconds between cycles, to a cycle
every second.
NOTE:The wiper delay times depend on vehicle speed.
If the vehicle is moving less than 10 mph (16 km/h),
delay times will be doubled.
NOTE:If the front wiper is operating when the ignition
is turned off, the wiper will automatically return to the
Parkposition. When the vehicle is restarted, the wipers
will resume operation.
Adding Washer Fluid
The fluid reservoir for the windshield washers is located
in the engine compartment and should be checked for
fluid level at regular intervals. Fill the reservoir with
windshield washer solvent (not radiator antifreeze) and
operate the system for a few seconds to flush out the
residual water. Refer to the appropriate engine diagram
(Section 7 “Maintaining Your Vehicle”) for the location of
the reservoir.
Wiper Control
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 111
3
Page 303 of 376
Body Lubrication
Locks and all body pivot points, including such items as
seat tracks, doors, liftgate and hood hinges, should be
lubricated periodically to assure quiet, easy operation
and to protect against rust and wear. Prior to the appli-
cation of any lubricant, the parts concerned should be
wiped clean to remove dust and grit; after lubricating
excess oil and grease should be removed. Particular
attention should also be given to hood latching compo-
nents to insure proper function. When performing other
underhood services, the hood latch, release mechanism
and safety catch should be cleaned and lubricated.
The external lock cylinders should be lubricated twice a
year, preferably in the fall and spring. Apply a small
amount of a high quality lubricant such as MoparLock
Cylinder Lubricant directly into the lock cylinder.
Windshield Wiper Blades
Clean the rubber edges of the wiper blades and the
windshield periodically with a sponge or soft cloth and a
mild non abrasive cleaner or use the washer solvent. This
will remove accumulations of salt, waxes or road film
and help reduce streaking and smearing.
Operation of the wipers on dry glass for long periods
may cause deterioration of the wiper blades. Always use
washer fluid when using the wipers to remove salt or dirt
from a dry windshield. Avoid using the wiper blades to
remove frost or ice from the windshield. Make sure that
they are not frozen to the glass before turning them on to
avoid damaging the blade. Keep the blade rubber out of
contact with petroleum products such as engine oil,
gasoline, etc.
Windshield Wiper Blade Replacement
1. Lift the wiper arm away from the glass.
2. Push the release tab shown in the illustration and slide
the wiper blade assembly down along the arm. Gently
place the wiper arm on the windshield.
MAINTAINING YOUR VEHICLE 303
7
Page 371 of 376
Vacuum/Vapor Harnesses................ 309
VanityMirrors .......................... 73
Variance, Compass...................... 151
Vehicle Certification Label................ 258
Vehicle Identification Number (VIN).......... 6
Vehicle Loading..................232,258,260
Vehicle Modifications/Alterations............ 6
Vehicle Storage......................200,321
Vehicle Theft Alarm (Security Alarm)......... 14
Video Entertainment System
(Rear Seat Video System)................. 187
Warning Lights
(Instrument Cluster Description)............ 139
Warnings and Cautions.................... 6
Warranty Information.................... 352Washer, Adding Fluid.................... 111
Washers, Windshield.................... 109
Washing Vehicle........................ 314
Wheel Alignment and Balance............. 242
Wheel and Wheel Trim................... 315
Wheel and Wheel Trim Care............... 315
WindBuffeting ...................... 29,123
Window Fogging....................... 200
Windows.............................. 26
Power.............................. 26
Windshield Washers..................... 109
Windshield Wipers...................109,303
Wiper Blade Replacement................. 303
Wipers,Intermittent ..................... 111
YES EssentialsFabric Cleaning Procedure.... 316
INDEX 371
10