wiper fluid CHRYSLER TOWN AND COUNTRY 2006 4.G Owners Manual

Intermittent Rear Wiper Operation — Automatic
Temperature Control Only
When this button is pressed and the ignition
switch is in the ON position, the rear wiper will
operate at a fixed interval of about 8 seconds. As
vehicle speed increases, the time delay will shorten. The
switch position as well as an indicator light will show
when the wiper is ON.
Rear Washer Operation — Automatic
Temperature Control Only
Press and hold the button as long as spray is
desired. If the switch is depressed while the wipers
are on, the wipers will operate for a few seconds
after the switch is released then resume the previously set
mode of intermittent wiper or continuous wipe. If the
switch is depressed when the wipers are off, the wipers
will operate for two cycles, then turn off. NOTE:
The washers will stop spraying if the switch is
pressed longer than 10 seconds.
Adding Washer Fluid
The fluid reservoir for the windshield washers and the
rear window washer is shared. It is located in the front of
the engine compartment on the passenger side and
should be checked for fluid level at regular intervals. Fill
the reservoir with windshield washer solvent (not radia-
tor antifreeze) and operate the system for a few seconds
to flush out the residual water.
304 UNDERSTANDING YOUR INSTRUMENT PANEL

â–«Steering Linkage ......................413
â–« Drive Shaft Universal Joints ..............413
â–« Body Lubrication .....................414
â–« Windshield Wiper Blades ................414
â–« Windshield And Rear Window Washers .....415
â–« Exhaust System ......................415
â–« Cooling System .......................416
â–« Hoses And Vacuum/Vapor Harnesses .......421
â–« Brakes .............................422
▫ Master Cylinder — Brake Fluid Level Check . . 423
â–« Fuel System Hoses ....................425
â–« Automatic Transmission ................425
â–« Front And Rear Wheel Bearings ...........428 â–«
Appearance Care And Protection From
Corrosion ...........................428
â–« Cleaning The Instrument Panel And Underseat
Cup Holders ........................433

Integrated Power Module (IPM) ............434

Vehicle Storage ........................437

Replacement Light Bulbs .................438

Bulb Replacement ......................439
â–« Headlights ..........................439
â–« Front Park/Turn Signal And Sidemarker
Lights .............................440
â–« Front Fog Light ......................441
â–« Rear Tail, Stop, Turn Signal, Side Marker And
Back-Up Lights .......................442
396 MAINTAINING YOUR VEHICLE

Continued operation could result in failure of the univer-
sal joint due to water and dirt contamination of the
grease. This would require complete replacement of the
joint assembly.
Body Lubrication
Locks and all body pivot points, including such items as
seat tracks, doors, liftgate, sliding doors and hood hinges,
should be lubricated periodically to assure quiet, easy
operation and to protect against rust and wear. Prior to
the application of any lubricant, the parts concerned
should be wiped clean to remove dust and grit; after
lubricating excess oil and grease should be removed.
Particular attention should also be given to hood latching
components to insure proper function. When performing
other underhood services, the hood latch, release mecha-
nism and safety catch should be cleaned and lubricated. The external lock cylinders should be lubricated twice a
year, preferably in the fall and spring. Apply a small
amount of a high quality lubricant such as Mopar
Lock
Cylinder Lubricant directly into the lock cylinder.
Windshield Wiper Blades
The rubber edges of the wiper blades and the windshield
should be cleaned periodically with a sponge or soft cloth
and a mild nonabrasive cleaner. This will remove accu-
mulations of salt or road film.
Operation of the wipers on dry glass for long periods
may cause deterioration of the wiper blades. Always use
washer fluid when using the wipers to remove salt or dirt
from a dry windshield.
Avoid using the wiper blades to remove frost or ice from
the windshield. Keep the blade rubber out of contact with
petroleum products such as engine oil, gasoline, etc.
414 MAINTAINING YOUR VEHICLE

Vanity Mirrors........................... 95
Variance, Compass ....................... 166
Vehicle Certification Label ................. 352
Vehicle Identification Number (VIN) ............ 6
Vehicle Information Center ................. 168
Vehicle Loading ................... 329,352,353
Vehicle Modifications/Alterations .............. 7
Vehicle Storage ....................... 301,437
Vehicle Theft Alarm (Security Alarm) .......... 27
Warning Flasher, Hazard .................. 368
Warning Lights (Instrument Cluster Description) . 209
Warnings and Cautions ..................... 6
Warranty Information ..................... 471
Washer, Adding Fluid .................. 304,415
Washer, Rear ........................ 303,304
Washing Vehicle ......................... 429
Wheel Alignment and Balance ............... 340
Wheel and Wheel Trim .................... 430 Wheel Bearings
......................... 428
Wind Buffeting ....................... 41,180
Window Fogging ........................ 301
Windows .............................. 40
Power ............................... 40
Rear Vent ............................ 40
Windshield Washers ................... 154,415
Windshield Wiper Blades .................. 414
Windshield Wipers ....................... 154
Wiper Blade Replacement .................. 414
Wiper, Rear ............................ 303
Wipers, Intermittent ...................... 155
Zone Control (Temperature Control) .......... 281
INDEX 493
10