bulb CHRYSLER VOYAGER 1996 Owner's Manual

INSTALLATION
(1) Position fog lamp on vehicle.
(2) Connect wire connector to body wire harness.
(3) Install fog lamp into bumper fascia.
(4) Install screws to hold fog lamp to front bumper
fascia.
FOG LAMP ± TOWN and COUNTRY
REMOVAL
(1) From behind fascia remove nuts attaching fog
lamp housing to fascia (Fig. 3).
(2) Remove fog lamp from fascia.
(3) Disconnect wire connector from body wire har-
ness.
(4) Remove fog lamp housing from vehicle.
INSTALLATION
(1) Connect wire connector to body wire harness.
(2) Position fog lamp on vehicle.
(3) Verify fog lamp operation.
(4) Insert fog lamp into bumper fascia.
(5) Install nuts attaching fog lamp to fascia.
FRONT SIDE MARKER LAMP TOWN and COUNTRY
REMOVAL
(1) Remove screw attaching side marker lamp.
(2) Remove housing by pulling rearward and away
from fascia (Fig. 7).
(3) Rotate lamp socket counterclockwise one quar-
ter turn.
(4) Pull bulb socket from the rear of lamp (Fig. 4).
(5) Remove side marker housing from vehicle.
INSTALLATION
(1) Insert bulb socket into rear of housing.
(2) Rotate park and turn signal socket clockwise
one quarter turn.
(3) Verify bulb(s) operation.
(4) Install screw attaching side marker lamp.
FRONT PARKING AND TURN SIGNAL LAMP ±
TOWN and COUNTRY
REMOVAL
(1) Remove screw attaching side marker lamp.
(2) Remove housing by pulling outward and away
from the fascia (Fig. 10).
Fig. 2 Fog Lamp
Fig. 3 Fog Lamp Bulb ± T&C
Fig. 4 Front Side Marker Lamp ± T&C
NSLAMPS 8L - 15
REMOVAL AND INSTALLATION (Continued)

(3) Remove screw attaching parking and turn sig-
nal lamp housing to fascia.
(4) Rotate lamp socket(s) counterclockwise one
quarter turn (Fig. 11).
(5) Pull bulb socket(s).
(6) Remove parking and turn signal lamp housing
from vehicle (Fig. 5).
INSTALLATION
(1) Insert bulb socket into housing.
(2) Rotate parking and turn signal socket clock-
wise one quarter turn.
(3) Verify bulb(s) operation.
(4) Install screw attaching parking and turn signal
lamp housing.
(5) Install screw attaching side marker lamp.
TAIL, STOP, TURN SIGNAL AND BACK-UP LAMP
REMOVAL
(1) Release liftgate latch and open liftgate.
(2) Remove screws holding tail, stop, turn signal
and back-up lamp to rear door opening trough.
(3) Remove inner end of lamp from quarter panel.
(4) Disengage hook holding outer end of lamp to
quarter panel opening.
(5) Remove lamp from quarter panel (Fig. 6).
(6) Disconnect positive lock on wire connector (Fig.
7).
(7) Depress lock tab on the side of the body har-
ness connector.
(8) Disconnect wire connector from tail lamp cir-
cuit board.
(9) Remove tail lamp from vehicle.
INSTALLATION
(1) Place tail lamp in position on vehicle.
(2) Connect wire connector into tail lamp circuit
board.
(3) Connect positive lock on wire connector.
(4) Place lamp in position in position on quarter
panel.(5) Engage hook to hold outer end of lamp to quar-
ter panel opening.
(6) Position inner end of lamp into quarter panel.
(7) Install screws to hold tail, stop, turn signal and
back-up lamp to rear door opening trough.
(8) Verify tail lamp operation.
LICENSE PLATE LAMP
REMOVAL
(1) Release liftgate latch and open liftgate.
(2) Remove liftgate trim panel. Refer to Group 23,
Body, for proper procedures.
(3) Remove water shield as necessary to gain
access to back of license plate lamp bar.
(4) Disconnect wire connector from liftgate wire
harness.
(5) Remove screws holding license plate lamp bar
to liftgate.
(6) Remove license plate lamp bar from liftgate
(Fig. 8).
(7) Remove license plate lamp bar from vehicle.
Fig. 5 Parking and Turn Signal Lamp Housing ±
T&C
Fig. 6 Tail, Stop, Turn Signal and Back-up Lamp
Fig. 7 Tail Lamp Connector
8L - 16 LAMPSNS
REMOVAL AND INSTALLATION (Continued)

NOTE: Wire connector may be disconnected at
socket which eliminates removal of liftgate trim.
INSTALLATION
(1) Place license plate lamp bar in position on lift-
gate.
(2) Install screws to hold license plate lamp bar to
liftgate.
(3) Connect wire connector into liftgate wire har-
ness.
(4) Install water shield.
(5) Install liftgate trim panel.
(6) Verify license plate lamp operation.
CENTER HIGH MOUNTED STOP LAMP (CHMSL)
REMOVAL
(1) Release liftgate latch and open liftgate.(2) Disengage clips holding CHMSL access cover to
liftgate.
(3) Remove cover from liftgate.
(4) Rotate bulb sockets counterclockwise one quar-
ter turn.
(5) Pull sockets from lamp.
(6) Remove screws holding CHMSL to liftgate.
(7) Remove CHMSL from vehicle (Fig. 9).
INSTALLATION
(1) Place CHMSL in position on vehicle.
(2) Install screws to hold CHMSL to liftgate.
(3) Insert bulb into socket.
(4) Insert sockets into lamp.
(5) Rotate bulb sockets clockwise one quarter turn.
(6) Place CHMSL access cover in position on lift-
gate.
(7) Engage clips to hold access cover to liftgate.
(8) Verify CHMSL operation.
Fig. 8 License Plate Lamp
Fig. 9 CHMSL
NSLAMPS 8L - 17
REMOVAL AND INSTALLATION (Continued)

INTERIOR LAMPS
INDEX
page page
REMOVAL AND INSTALLATION
CONVENIENCE BIN LAMP................. 20
DOME LAMP BULB...................... 21
DOME LAMP........................... 21
FRONT DOOR COURTESY LAMP BULB...... 22
FRONT DOOR COURTESY LAMP........... 21
GLOVE BOX LAMP AND SWITCH........... 19
GLOVE BOX LAMP BULB.................. 19
HEADER READING/COURTESY LAMP BULB . . . 19HEADER READING/COURTESY LAMP....... 18
IGNITION HALO LAMP BULB............... 19
INSTRUMENT PANEL LAMPS AND SWITCHES . 20
LIFTGATE COURTESY LAMP BULB.......... 24
LIFTGATE COURTESY LAMP............... 23
OVERHEAD CONSOLE READING/COURTESY
LAMP BULB.......................... 18
RAIL LAMP MODULE BULB................ 23
REMOVAL AND INSTALLATION
OVERHEAD CONSOLE READING/COURTESY LAMP
BULB
REMOVAL
(1) Using a trim stick, lightly pry outward the for-
ward end of reading lamp lens.
(2) Rotate reading lamp bulb socket one quarter
turn counterclockwise.
(3) Pull socket out of lamp (Fig. 1).
(4) Pull bulb from socket.
INSTALLATION
(1) Push bulb into socket.
(2) Push socket into lamp.
(3) Rotate reading lamp bulb socket one quarter
turn clockwise.
(4) Insert tab on lamp lens between lamp switch
and overhead console.(5) Snap lens onto lamp lens pivots.
HEADER READING/COURTESY LAMP
REMOVAL
(1) Grasp outer edges of header reading/courtesy
lamp at headlining.
(2) Pull downward to disengage clips on reading/
courtesy lamp from roof header panel (Fig. 2).
(3) Disconnect wire connector from reading/cour-
tesy lamp.
(4) Remove lamp from vehicle.
INSTALLATION
(1) Position lamp on vehicle.
(2) Connect wire connector to reading/courtesy
lamp.
(3) Align clips on reading/courtesy lamp to mating
holes in roof header panel.
(4) Push upward to engage clips on reading/cour-
tesy lamp to roof header panel.
Fig. 1 Reading/Courtesy LampFig. 2 Header Reading/Courtesy Lamp
8L - 18 LAMPSNS

HEADER READING/COURTESY LAMP BULB
REMOVAL
(1) Insert a small, flat bladed pry tool at forward
position between reading/courtesy lamp lens and
lamp housing.
(2) Pry lamp lens from lamp housing (Fig. 3).
(3) Insert a small, flat bladed pry tool between
lamp light shield and lamp housing at inboard rear
corner of light shield.
(4) Pry light shield from housing (Fig. 4).
(5) Carefully press forward lamp bulb contact
toward opposite contact and rotate.
(6) Remove bulb from lamp bulb contacts.
INSTALLATION
(1) Carefully press forward lamp bulb contact
toward opposite contact and rotate bulb into position.
(2) Position bulb to lamp bulb contacts.
(3) Release lamp bulb contacts.
(4) Insert outer edge of light shield into lamp
housing (Fig. 4).(5) Rotate light shield upward and snap inboard
edge into lamp housing.
(6) Position lens switch tab to lamp switch.
(7) Press lens pivots to tabs on lamp housing until
both pivots are seated.
GLOVE BOX LAMP AND SWITCH
REMOVAL
(1) Open glove box door.
(2) Using a trim stick, lightly pry glove box lamp/
switch from instrument panel.
(3) Disconnect wire connector from glove box lamp
(Fig. 5).
(4) Remove glove box lamp from vehicle.
INSTALLATION
(1) Position glove box lamp in vehicle.
(2) Connect wire connector from glove box lamp.
(3) Position glove box lamp in instrument panel.
(4) Press lamp into instrument panel until fully
seated.
GLOVE BOX LAMP BULB
REMOVAL
(1) Remove glove box lamp/switch from instrument
panel.
(2) Pull bulb from glove box lamp (Fig. 6).
INSTALLATION
(1) Push bulb into glove box lamp.
(2) Install glove box lamp/switch in instrument
panel.
IGNITION HALO LAMP BULB
REMOVAL
(1) Remove steering column trim covers. Refer to
Group 19, Steering, for proper procedures.
Fig. 3 Reading/Courtesy Lamp Lens
Fig. 4 Reading/Courtesy Lamp Light Shield
Fig. 5 Glove Box Lamp and Switch
NSLAMPS 8L - 19
REMOVAL AND INSTALLATION (Continued)

(2) Rotate bulb socket counterclockwise one quar-
ter turn (Fig. 7).
(3) Pull bulb socket from halo lamp.
INSTALLATION
(1) Push bulb socket into halo lamp.
(2) Rotate bulb socket clockwise one quarter turn.
(3) Install steering column trim covers. Refer to
Group 19, Steering, for proper procedures.
CONVENIENCE BIN LAMP
If the lamp is not used refer to (Fig. 8).
REMOVAL
(1) Pull out the convenience bin cup holder.
(2) Insert the trim stick between access cover
above cup holder and center console.
(3) Carefully pry the access cover from the center
console (Fig. 9).
(4) Remove the access cover from the vehicle.(5) Using needle-nose pliers, carefully squeeze the
vertical metal legs of the lamp hood.
(6) Lift the lamp hood upward from the cup holder
tray.
(7) Carefully pull the lamp and wiring rearward
from the instrument panel (Fig. 10).
(8) Pull the lamp hood from the lamp socket.
(9) Pull bulb from socket.
INSTALLATION
For installation, reverse the above procedures.
INSTRUMENT PANEL LAMPS AND SWITCHES
For replacement of instrument panel lamps and
switches, refer to Group 8E, Instrument Panel and
Systems.
Fig. 6 Glove Box Lamp Bulb
Fig. 7 Ignition Halo Lamp Bulb
Fig. 8 Wiring for the Convenience Lamp
Fig. 9 Convenience Bin Access Cover
Fig. 10 Convenience Bin Lamp Bulb
8L - 20 LAMPSNS
REMOVAL AND INSTALLATION (Continued)

DOME LAMP
REMOVAL
(1) Insert a small, flat bladed pry tool between
dome lamp lens and dome lamp body on left side of
dome lamp.
(2) Disengage left side of dome lamp lens from
lamp body (Fig. 11).
(3) Pivot dome lamp lens downward until lens
hook is clear of headlining.
(4) Slide dome lamp toward right side of vehicle
until hook on dome lamp is clear of headlining (Fig.
12).
(5) Remove dome lamp from headlining.
(6) Disconnect wire connector from dome lamp.
(7) Remove dome lamp from vehicle.
INSTALLATION
(1) Position dome lamp in vehicle.
(2) Connect wire connector to dome lamp.
(3) Position dome lamp to headlining.
(4) Position hook on dome lamp above headlining
and slide lamp toward left side of vehicle until hook
on dome lamp is fully engaged to headlining.
(5) Push upward on dome lamp until dome lamp is
tight to headlining.
(6) Pivot dome lamp lens upward. Verify that lamp
lens hook is above the headlining.
(7) Install left side of dome lamp lens to lamp
body.
DOME LAMP BULB
REMOVAL
(1) Insert a small, flat bladed pry tool between
dome lamp lens and dome lamp body on left side of
dome lamp.
(2) Disengage left side of dome lamp lens from
lamp body (Fig. 13).
(3) Pull bulb from lamp socket
INSTALLATION
(1) Push bulb into lamp socket.
(2) Pivot dome lamp lens upward. Verify that lamp
lens hook is above the headlining.
(3) Engage left side of dome lamp lens to lamp
body.
FRONT DOOR COURTESY LAMP
REMOVAL
(1) Insert a trimstick between courtesy lamp hous-
ing and door trim panel (Fig. 14).
(2) Pry rear edge of housing from trim panel.
Fig. 11 Dome Lamp Lens
Fig. 12 Dome Lamp Hook
Fig. 13 Dome Lamp Bulb
NSLAMPS 8L - 21
REMOVAL AND INSTALLATION (Continued)

(3) Separate housing from trim panel.
(4) Disengage wire connector from lamp.
(5) Separate lamp housing from vehicle.
INSTALLATION
(1) Position lamp housing to vehicle.
(2) Engage wire connector to lamp.
(3) Slide tab on forward edge of housing behind
trim panel.
(4) Snap rear edge of housing into trim panel.
FRONT DOOR COURTESY LAMP BULB
REMOVAL
(1) Using a small, flat bladed pry tool, pry rear
edge of courtesy lamp lens from courtesy lamp (Fig.
15).
(2) Remove lens from lamp.
(3) Squeeze brass lamp bulb contacts together gen-
tly.(4) Disengage bulb from lamp contacts (Fig. 16).
(5) Remove bulb from lamp.
Fig. 14 Door Courtesy Lamp Housing
Fig. 15 Door Courtesy Lamp Lens
Fig. 16 Door Courtesy Lamp Bulb
8L - 22 LAMPSNS
REMOVAL AND INSTALLATION (Continued)

INSTALLATION
(1) Position bulb to lamp contacts.
(2) Engage bulb to lamp contacts.
(3) Insert long edge of lens into lamp housing.
(4) Press on center of lens to engage remainder of
clips
RAIL LAMP MODULE BULB
REMOVAL
(1) Using a small screw driver, pry stationary end
of rail lamp lens from rail lamp module (Fig. 17).
(2) Remove lens tab from between rail lamp mod-
ule and rail lamp switch.
(3) Remove lens from lamp.
(4) Pull bulb from lamp (Fig. 18).
INSTALLATION
(1) Push bulb into bulb contacts in rail lamp mod-
ule.
(2) Insert tab on lamp lens between rail lamp mod-
ule and rail lamp switch.(3) Snap lens onto lens pivots on module.
LIFTGATE COURTESY LAMP
REMOVAL
(1) Insert trim stick between courtesy lamp and
liftgate trim panel at upper inboard corner of cour-
tesy lamp (Fig. 19).
(2) Disengage tabs holding courtesy lamp to lift-
gate trim panel (Fig. 20).
(3) Disconnect wire connector from courtesy lamp.
(4) Remove lamp from vehicle.
INSTALLATION
(1) Position lamp to vehicle.
(2) Connect wire connector to courtesy lamp.
Fig. 17 Rail Lamp Module Lens
Fig. 18 Rail Lamp Module Bulb
Fig. 19 Courtesy Lamp
Fig. 20 Courtesy Lamp Tabs
NSLAMPS 8L - 23
REMOVAL AND INSTALLATION (Continued)

(3) Position courtesy lamp to liftgate trim panel.
(4) Press courtesy lamp into trim panel until tabs
engage fully to trim panel.
LIFTGATE COURTESY LAMP BULB
REMOVAL
(1) Remove liftgate courtesy lamp.
(2) Insert a small, flat bladed pry tool between
courtesy lamp lens and courtesy lamp body.
(3) Carefully depress tabs holding lens to courtesy
lamp body (Fig. 21).
(4) Remove lamp lens from lamp body.
(5) Carefully press lamp bulb contact toward oppo-
site contact.
(6) Remove bulb from lamp body.
INSTALLATION
(1) Carefully press lamp bulb contact toward oppo-
site contact.
(2) Position bulb to lamp bulb contacts.(3) Position long side of lamp lens to tabs on lamp
body.
(4) Press on center of lens to engage tabs on oppo-
site side of lamp body.
(5) Install liftgate courtesy lamp.
Fig. 21 Liftgate Courtesy Lamp Bulb
8L - 24 LAMPSNS
REMOVAL AND INSTALLATION (Continued)