check engine CHRYSLER VOYAGER 2000 Diagnostic Manual

TEST ACTION APPLICABILITY
4 Ignition Off
Disconnect the Fuel Pump Relay.
Note: Check connectors - Clean/repair as necessary.
Ignition On, Engine Not Running
Using a Voltmeter, measure the Fused Ignition Switch Output Circuit.
Is the voltage above 10.0 volts?All
Ye s®Go To 5
No®Repair the open Fused Ignition Switch Output Circuit.
Perform Powertrain Verification Test VER-2A.
5 Ignition Off
Disconnect the Fuel Pump Relay.
Note: Check connectors - Clean/repair as necessary.
Using an Ohmmeter, measure across Terminals 85 and 86 of the Fuel Pump Relay for
resistance.
Is the resistance between 50 and 90 ohms?All
Ye s®Go To 6
No®Replace Fuel Pump Relay.
Perform Powertrain Verification Test VER-2A.
6 Ignition Off
Disconnect the Powertrain Control Module Connector.
Note: Check connectors - Clean/repair as necessary.
Disconnect the Fuel Pump Relay.
Note: Check connectors - Clean/repair as necessary
Using an Ohmmeter, measure the Fuel Pump Relay Control Circuit for resistance.
Is the resistance below 5.0 ohms?All
Ye s®Go To 7
No®Repair the open Fuel Pump Relay Control Circuit.
Perform Powertrain Verification Test VER-2A.
7 Ignition Off
Disconnect the PCM Connector.
Note: Check connectors - Clean/repair as necessary.
Disconnect the Fuel Pump Relay.
Note: Check connectors - Clean/repair as necessary.
Using an Ohmmeter, measure the Fuel Pump Relay Control Circuit to ground.
Is the resistance below 5.0 ohms?All
Ye s®Repair the Fuel Pump Relay Control Circuit for a short to ground.
Perform Powertrain Verification Test VER-2A.
No®Go To 8
8 Ignition off.
If there are no potential causes remaining, the PCM is assumed to be defective.
View repair options.All
Repair
Replace the PCM.
Perform Powertrain Verification Test VER-2A.
179
DRIVEABILITY
P1282 FUEL PUMP RELAY CONTROL CIRCUIT ÐContinued
ProCarManuals.com

TEST ACTION APPLICABILITY
3 Ignition off.
Remove the Throttle Body per service information procedure.
Note: Clean Throttle Body in a well ventilated area and wear rubber gloves.
While holding the Throttle open spray entire Throttle Body Bore with Mopar parts
cleaner.
Using a soft scuff pad, clean the Throttle Body Bore and Throttle Plate.
Using compressed air, dry the Throttle Body and install Throttle Body on Manifold.
Reconnect IAC Motor Connector and reset the IAC Motor Steps with the DRB.
Start engine and let idle.
With the DRB, actuate the minimum air flow.
Is the idle RPM within the range shown in the chart? Refer to the Service
Information.All
Ye s®Test Complete.
No®Replace the Throttle Body.
Perform Powertrain Verification Test VER-5A.
4 Ignition Off
Start engine, allow engine idle to stabilize for 60 seconds.
With the DRB, read target idle and engine RPM.
Is the engine RPM within +200/-100 RPM of target idle?All
Ye s®Go To 5
No®Go To 8
5 Ignition Off
Remove the IAC Motor from the housing.
Turn Ignition on with Engine Not Running.
With the DRB, actuate the IAC Stepper Motor.
Wiggle the Wiring Harness from the IAC Motor to the PCM.
Did the IAC stop operating at any time?All
Ye s®Repair the Harness or Connectors as necessary.
Perform Powertrain Verification Test VER-5A.
No®Go To 6
6 Ignition Off
Using the schematic as a guide, inspect the Wiring and Connectors.
Were any problems found?All
Ye s®Repair as necessary.
Perform Powertrain Verification Test VER-5A.
No®Go To 7
7 Ignition On, Engine Not Running
Check Throttle Plate and Linkage for a binding condition.
The Throttle Linkage must be free and the Throttle Plate at the idle
position.
Ensure Throttle Plate is fully closed and against its stop.
Is the Throttle Plate and Linkage okay?All
Ye s®Test Complete.
No®Repair as necessary.
Perform Powertrain Verification Test VER-5A.
181
DRIVEABILITY
P-1294 TARGET IDLE NOT REACHED ÐContinued
ProCarManuals.com

TEST ACTION APPLICABILITY
8 Ignition Off
Start engine, allow engine idle to stabilize for 60 seconds.
With the engine running at idle, the DRB in Systems Test, perform the IAC wiggle
test.
The idle speed should raise and lower with the display.
Does the RPM raise and lower correctly?All
Ye s®Go To 9
No®Refer to symptom P-0505 IDLE AIR CONTROL MOTOR CIR-
CUITS in the DRIVEABILITY category.
9 Ignition Off
Start engine, allow engine idle to stabilize for 60 seconds.
Check engine Vacuum Hoses and Components for vacuum leaks.
Ensure PCV Valve is the correct part and is operating correctly.
Were any problems found?All
Ye s®Repair as necessary.
Perform Powertrain Verification Test VER-5A.
No®Go To 10
10 Ignition Off
Remove the IAC Motor from the housing.
Turn Ignition on with Engine Not Running.
With the DRB, actuate the IAC Stepper Motor.
Wiggle the Wiring Harness from the IAC Motor to the PCM.
Did the IAC stop operating at any time?All
Ye s®Repair the Harness or Connectors as necessary.
Perform Powertrain Verification Test VER-5A.
No®Go To 11
11 Ignition On, Engine Not Running
Check Throttle Plate and Linkage for a binding condition.
The Throttle Linkage must be free and the Throttle Plate at the idle
position.
Ensure Throttle Plate is fully closed and against its stop.
Is the Throttle Plate and Linkage okay?All
Ye s®Go To 12
No®Repair as necessary.
Perform Powertrain Verification Test VER-5A.
12 Ignition Off
Using the schematic as a guide, inspect the Wiring and Connectors.
Were any problems found?All
Ye s®Repair as necessary.
Perform Powertrain Verification Test VER-5A.
No®Test Complete.
182
DRIVEABILITY
P-1294 TARGET IDLE NOT REACHED ÐContinued
ProCarManuals.com

Symptom:
P-1297 NO CHANGE IN MAP FROM START TO RUN
When Monitored and Set Condition:
P-1297 NO CHANGE IN MAP FROM START TO RUN
When Monitored: Engine is idling with a stable RPM (RPM fluctuation < 64 RPM) and
the vehicle is not moving.
Set Condition: Too small a difference is seen between barometric pressure at ignition on
and manifold vacuum.
POSSIBLE CAUSES
MAP SENSOR 5-VOLT SUPPLY CIRCUIT OPEN
MAP SENSOR WIRING HARNESS INTERMITTENT DEF
VACUUM PORTS RESTRICTED OR DEFECTIVE
MANIFOLD ABSOLUTE PRESSURE SENSOR RESTRICTED
MAP SENSOR DEFECTIVE (A)
MAP SENSOR DEFECTIVE (B)
TEST ACTION APPLICABILITY
1 Ignition On, Engine Not Running
With the DRB, read codes
Is9MAP Sensor voltage too low9code set?All
Ye s®Refer to symptom P-0107 MAP SENSOR VOLTAGE TOO LOW in
the DRIVEABILITY category.
No®Go To 2
2 With the DRB erase Codes.
Ignition On, Engine Not Running
Start engine and allow engine to idle for 30 seconds.
With the DRB read codes.
Does the DRB show9No change in MAP from start to run9?All
Ye s®Go To 3
No®Go To 6
3 Ignition on, with engine not running.
Disconnect MAP Sensor.
Note:Check connectors - clean/repair as necessary.
Ignition on, with engine not running.
Using a Voltmeter, measure the MAP Sensor 5-Volt Supply Circuit at the MAP
Sensor Connector.
Is the voltage above 4.0 volts?All
Ye s®Go To 4
No®Repair the open MAP Sensor 5-volt Supply Circuit.
Perform Powertrain Verification Test VER-5A.
183
DRIVEABILITY
ProCarManuals.com

TEST ACTION APPLICABILITY
4 Ignition off.
Remove MAP Sensor and inspect for Vacuum restrictions.
Check connectors - Clean/repair as necessary.
Was there a restriction?All
Ye s®Remove the restriction and reinstall the MAP Sensor
Perform Powertrain Verification Test VER-5A.
No®Go To 5
5 If there are no potential causes remaining, the MAP Sensor is assumed to be
defective.
View repair options.All
Repair
Replace the MAP Sensor.
Perform Powertrain Verification Test VER-5A.
6 Engine must be running.
While monitoring the DRB display, snap the Throttle open and closed.
Did the vacuum drop rapidly below 1.09?All
Ye s®Go To 7
No®Go To 8
7 Engine must be running.
With the DRB,set the engine speed to 1500 RPM.
With the engine RPM at 1500, read MAP sensor voltage.
While monitoring the voltage, wiggle the wiring from the MAP Sensor to PCM.
Did the engine stall or voltage become erratic?All
Ye s®Repair the Wiring or Connector defective between the Map
Sensor and the PCM.
Perform Powertrain Verification Test VER-5A.
No®Test Complete.
8 Engine must be running.
With the DRB,set the engine speed to 1500 RPM.
With the engine RPM at 1500, read MAP sensor voltage.
While monitoring the voltage, wiggle the wiring from the MAP Sensor to PCM.
Did the engine stall or voltage become erratic?All
Ye s®Repair the Wiring or Connector defective between the Map
Sensor and the PCM.
Perform Powertrain Verification Test VER-5A.
No®Go To 9
9 Ignition Off
Remove the MAP Sensor and inspect condition of Intake Manifold and MAP Sensor
Vacuum Ports.
Check connectors - Clean/repair as necessary.
Is there a restriction or defect in the Vacuum Ports?All
Ye s®Repair the restricted or defective Vacuum Ports.
Perform Powertrain Verification Test VER-5A.
No®Go To 10
184
DRIVEABILITY
P-1297 NO CHANGE IN MAP FROM START TO RUN ÐContinued
ProCarManuals.com

TEST ACTION APPLICABILITY
4 Ignition Off
Disconnect the PCM Connector.
Note: Check connectors - Clean/repair as necessary.
Remove the Auto Shutdown Relay.
Note: Check connectors - Clean/repair as necessary.
Using an ohmmeter, measure the resistance of the ASD Relay Output Circuit from
ASD Relay to the PCM Connector.
Is the resistance above 5.0 ohms?All
Ye s®Repair open ASD Relay Output Circuit.
Perform Powertrain Verification Test VER-2A.
No®Go To 5
5 Ignition off.
If there are no potential causes remaining, the Powertrain Control Module is
assumed to be defective.
View repair options.All
Repair
Replace the PCM.
Perform Powertrain Verification Test VER-2A.
6 Ignition Off
Remove the Auto Shutdown Relay.
Note: Check connectors - Clean/repair as necessary.
Using a Voltmeter, measure the Fused B (+) Circuit at Relay Connector.
Is the voltage above 10.0 volts?All
Ye s®Go To 7
No®Repair the open Fused B(+) Circuit. (Check Engine Fuse in PDC)
.
Perform Powertrain Verification Test VER-2A.
7 Ignition Off
Remove the Auto Shutdown Relay.
Note: Check connectors - Clean/repair as necessary.
Install a substitute Relay for the Auto Shutdown Relay.
Attempt to start the Vehicle.
Did the engine start?All
Ye s®Replace the original Auto Shutdown Relay.
Perform Powertrain Verification Test VER-2A.
No®Go To 8
8 Ignition Off.
Disconnect the Powertrain Control Module Connector.
Note: Check connectors - Clean/repair as necessary.
Remove the Auto Shutdown Relay.
Note: Check connectors - Clean/repair as necessary.
Using an ohmmeter, measure the resistance of the ASD Relay Output Circuit from
the Auto Shutdown Relay to the PCM.
Is the resistance above 5.0 ohms?All
Ye s®Repair open ASD Relay Output Circuit.
Perform Powertrain Verification Test VER-2A.
No®Go To 9
189
DRIVEABILITY
P-1389 NO ASD RELAY OUTPUT VOLTAGE AT PCM ÐContinued
ProCarManuals.com

TEST ACTION APPLICABILITY
2 Ignition Off.
Disconnect the CMP Sensor Connector.
Note: Check connectors - Clean/repair as necessary.
Inspect all Terminals.
Is any Terminal damaged, pushed out or miswired?ENGINE - 3.3L V6
and/or ENGINE -
3.8L V6 and/or EN-
GINE - 3.3L V6
FFV
Ye s®Repair Terminal(s) for damage, pushout or miswiring.
Perform Powertrain Verification Test VER-5A.
No®Go To 3
3 Ignition Off.
Disconnect the PCM.
Note: Check connectors - Clean/repair as necessary.
Inspect all Terminals.
Is any Terminal damaged, pushed out, or miswired?ENGINE - 3.3L V6
and/or ENGINE -
3.8L V6 and/or EN-
GINE - 3.3L V6
FFV
Ye s®Repair Terminal(s) for damage, pushout or miswiring.
Perform Powertrain Verification Test VER-5A.
No®Go To 4
4 Ignition Off.
Disconnect the CMP Sensor Connector.
Note: Check connectors - Clean/repair as necessary.
Remove the Camshaft Position Sensor.
Inspect the Camshaft Sprocket. See pertinent service information for instructions.
Is the Camshaft Sprocket okay?ENGINE - 3.3L V6
and/or ENGINE -
3.8L V6 and/or EN-
GINE - 3.3L V6
FFV
Ye s®Go To 5
No®Repair as necessary.
Perform Powertrain Verification Test VER-5A.
5 Ignition Off.
Disconnect the CMP Sensor Connector.
Note: Check connectors - Clean/repair as necessary.
Remove the CMP Sensor.
Inspect the Camshaft Thrust Plate(s).
Are the Camshaft Thrust Plate(s) attached?ENGINE - 3.3L V6
and/or ENGINE -
3.8L V6 and/or EN-
GINE - 3.3L V6
FFV
Ye s®Replace the Camshaft Position Sensor.
Perform Powertrain Verification Test VER-5A.
No®Repair or replace the Camshaft Thrust Plate(s) as necessary.
Perform Powertrain Verification Test VER-5A.
6 Start Engine.
At PCM, backprobe CMP Sensor Signal Circuit with Oscilloscope's voltage measure-
ment lead.
While observing the Oscilloscope pattern, wiggle CMP Sensor Circuit from Sensor to
PCM.
Were any signals missing when the wiggle test was conducted?ENGINE - 3.3L V6
and/or ENGINE -
3.8L V6 and/or EN-
GINE - 3.3L V6
FFV
Ye s®Note where wiggling the Wires caused a missing CMP Sensor
Signal. Repair Camshaft and Crankshaft Wiring Harness as
necessary.
Perform Powertrain Verification Test VER-5A.
No®Go To 7
192
DRIVEABILITY
P-1391 INTERMITTENT LOSS OF CMP OR CKP ÐContinued
ProCarManuals.com

TEST ACTION APPLICABILITY
7 Ignition Off.
At the CKP Sensor, backprobe the CKP Sensor Signal Circuit with the Oscilloscope's
voltage measurement lead.
Start the Engine and observe the CKP Sensor voltage pattern on the Oscilloscope.
Are any Crankshaft Position Sensor Signals missing?ENGINE - 3.3L V6
and/or ENGINE -
3.8L V6 and/or EN-
GINE - 3.3L V6
FFV
Ye s®Go To 8
No®Go To 11
8 Ignition Off.
Disconnect the CKP Sensor Connector.
Note: Check connectors - Clean/repair as necessary.
Inspect all Terminals.
Is any Terminal damaged, pushed out or miswired?ENGINE - 3.3L V6
and/or ENGINE -
3.8L V6 and/or EN-
GINE - 3.3L V6
FFV
Ye s®Repair Terminal(s) for damage, pushout or miswiring.
Perform Powertrain Verification Test VER-5A.
No®Go To 9
9 Ignition Off.
Disconnect the PCM.
Note: Check connectors - Clean/repair as necessary.
Inspect all Terminals.
Is any Terminal damaged, pushed out or miswired?ENGINE - 3.3L V6
and/or ENGINE -
3.8L V6 and/or EN-
GINE - 3.3L V6
FFV
Ye s®Repair Terminal(s) for damage, pushout or miswiring.
Perform Powertrain Verification Test VER-5A.
No®Go To 10
10 Ignition Off
Remove the Crankshaft Position (CKP) Sensor.
Inspect the Slots in the Flywheel for debris or damage.
Is the Flywheel damaged?ENGINE - 3.3L V6
and/or ENGINE -
3.8L V6 and/or EN-
GINE - 3.3L V6
FFV
Ye s®Repair or replace as necessary.
Perform Powertrain Verification Test VER-5A.
No®Replace the Crankshaft Position Sensor.
Perform Powertrain Verification Test VER-5A.
11 Start Engine.
At PCM, backprobe CKP Sensor Signal Circuit with Oscilloscope's voltage measure-
ment lead.
While observing the Oscilloscope pattern, wiggle CKP Sensor Circuit from Sensor to
PCM.
Were any CKP Sensor Signals missing when the wiggle test was conducted?ENGINE - 3.3L V6
and/or ENGINE -
3.8L V6 and/or EN-
GINE - 3.3L V6
FFV
Ye s®Note where wiggling the wires caused a missing CKP Sensor
signal. Repair Camshaft and Crankshaft Wire Harness as neces-
sary.
Perform Powertrain Verification Test VER-5A.
No®Test Complete.
193
DRIVEABILITY
P-1391 INTERMITTENT LOSS OF CMP OR CKP ÐContinued
ProCarManuals.com

TEST ACTION APPLICABILITY
12 Ignition Off.
At the CMP Sensor, backprobe the CMP Sensor Signal Circuit with the Oscilloscope
voltage measurement lead.
Start the Engine and observe the CMP Sensor voltage pattern on the Oscilloscope.
Are there any of the Camshaft Position Sensor Signals missing?ENGINE - 3.0L V6
Ye s®Go To 13
No®Go To 16
13 Ignition Off.
Disconnect the CMP Sensor Connector.
Note: Check connectors - Clean/repair as necessary.
Inspect all Terminals.
Is any Terminal damaged, pushed out or miswired?ENGINE - 3.0L V6
Ye s®Repair Terminal(s) for damage, pushout or miswiring.
Perform Powertrain Verification Test VER-5A.
No®Go To 14
14 Ignition Off.
Disconnect the PCM.
Note: Check connectors - Clean/repair as necessary.
Inspect all Terminals.
Is any Terminal damaged, pushed out, or miswired?ENGINE - 3.0L V6
Ye s®Repair Terminal(s) for damage, pushout or miswiring.
Perform Powertrain Verification Test VER-5A.
No®Go To 15
15 Ignition Off.
Remove Distributor Cap and Rotor.
Inspect the Pulse Ring for damage or misalignment.
Is the Pulse Ring okay?ENGINE - 3.0L V6
Ye s®Replace the Camshaft Position Sensor.
Perform Powertrain Verification Test VER-5A.
No®Repair or replace the Distributor Pulse Ring as necessary.
Perform Powertrain Verification Test VER-5A.
16 Start Engine.
At PCM, backprobe CMP Sensor Signal Circuit with Oscilloscope's voltage measure-
ment lead.
While observing the Oscilloscope pattern, wiggle CMP Sensor Circuit from Sensor to
PCM.
Were any signals missing when the wiggle test was conducted?ENGINE - 3.0L V6
Ye s®Note where wiggling the Wires caused a missing CMP Sensor
Signal. Repair Camshaft and Crankshaft Wiring Harness as
necessary.
Perform Powertrain Verification Test VER-5A.
No®Go To 17
194
DRIVEABILITY
P-1391 INTERMITTENT LOSS OF CMP OR CKP ÐContinued
ProCarManuals.com

TEST ACTION APPLICABILITY
17 Ignition Off.
At the CKP Sensor, backprobe the CKP Sensor Signal Circuit with the Oscilloscope's
voltage measurement lead.
Start the Engine and observe the CKP Sensor voltage pattern on the Oscilloscope.
Are any Crankshaft Position Sensor Signals missing?ENGINE - 3.0L V6
Ye s®Go To 18
No®Go To 21
18 Ignition Off.
Disconnect the CKP Sensor Connector.
Note: Check connectors - Clean/repair as necessary.
Inspect all Terminals.
Is any Terminal damaged, pushed out or miswired?ENGINE - 3.0L V6
Ye s®Repair Terminal(s) for damage, pushout or miswiring.
Perform Powertrain Verification Test VER-5A.
No®Go To 19
19 Ignition Off.
Disconnect the PCM.
Note: Check connectors - Clean/repair as necessary.
Inspect all Terminals.
Is any Terminal damaged, pushed out or miswired?ENGINE - 3.0L V6
Ye s®Repair Terminal(s) for damage, pushout or miswiring.
Perform Powertrain Verification Test VER-5A.
No®Go To 20
20 Ignition Off.
Remove the Crankshaft Position (CKP) Sensor.
Inspect the Slots in the Flywheel for debris or damage.
Is the Flywheel damaged?ENGINE - 3.0L V6
Ye s®Repair or replace as necessary.
Perform Powertrain Verification Test VER-5A.
No®Replace the Crankshaft Position Sensor.
Perform Powertrain Verification Test VER-5A.
21 Start Engine.
At PCM, backprobe CKP Sensor Signal Circuit with Oscilloscope's voltage measure-
ment lead.
While observing the Oscilloscope pattern, wiggle CKP Sensor Circuit from Sensor to
PCM.
Were any CKP Sensor Signals missing when the wiggle test was conducted?ENGINE - 3.0L V6
Ye s®Note where wiggling the wires caused a missing CKP Sensor
signal. Repair Camshaft and Crankshaft Wire Harness as neces-
sary.
Perform Powertrain Verification Test VER-5A.
No®Test Complete.
195
DRIVEABILITY
P-1391 INTERMITTENT LOSS OF CMP OR CKP ÐContinued
ProCarManuals.com