ignition CHRYSLER VOYAGER 2000 Diagnostic Manual

Symptom:
P-0601 INTERNAL CONTROLLER FAILURE
When Monitored and Set Condition:
P-0601 INTERNAL CONTROLLER FAILURE
When Monitored: With the ignition key on.
Set Condition: Internal checksum for software failed, does not match calculated value.
POSSIBLE CAUSES
INTERNAL CONTROLLER FAILURE
TEST ACTION APPLICABILITY
1 Ignition On, Engine Not Running.
With the DRB, read Trouble Codes.
Is Trouble Code INTERNAL CONTROLLER FAILURE present?All
Ye s®Replace the Powertrain Control Module.
Perform Powertrain Verification Test VER-2A
No®Test Complete.
169
DRIVEABILITY
ProCarManuals.com

Symptom:
P-0645 A/C CLUTCH RELAY CIRCUIT
When Monitored and Set Condition:
P-0645 A/C CLUTCH RELAY CIRCUIT
When Monitored: With the ignition key on and battery voltage greater than 10 volts.
Set Condition: An open or shorted condition is detected in the A/C clutch relay control
circuit.
POSSIBLE CAUSES
FUSED IGNITION SWITCH OUTPUT CIRCUIT OPEN
AIR CONDITIONING CLUTCH RELAY DEFECTIVE
A/C CLUTCH RELAY CIRCUIT WITHOUT INTER DEFECT
A/C CLUTCH RELAY CIRCUIT WITHOUT OBSER DEFECT
A/C CLUTCH RELAY CONTROL CIRCUIT SHORT TO GROUND
AIR CONDITIONING CLUTCH RELAY CONTROL CIRCUIT OPEN
PCM DEF (A/C CLUTCH RELAY)
TEST ACTION APPLICABILITY
1 Ignition On, Engine Not Running
Actuate the Air Conditioning Clutch Relay.
Is the Air Conditioning Clutch Relay clicking?All
Ye s®Go To 2
No®Go To 4
2 Ignition On, Engine Not Running
Actuate the Air Conditioning Clutch Relay.
Wiggle the Wiring Harness from the Relay to the PCM.
Did the wiggling interrupt the clicking?All
Ye s®Repair as necessary where wiggling caused the clicking to be
interrupted.
Perform Powertrain Verification Test VER-2A.
No®Go To 3
3 Ignition Off
Using the schematic as a guide, inspect the Wiring and Connectors.
Were any problems found?All
Ye s®Repair as necessary.
Perform Powertrain Verification Test VER-2A.
No®Test Complete.
170
DRIVEABILITY
ProCarManuals.com

TEST ACTION APPLICABILITY
4 Ignition Off
Remove the Air Conditioning Clutch Relay.
Note: Check connectors - Clean/repair as necessary.
Using a Voltmeter, measure the Fused Ignition Switch Output Circuit.
Is the voltage above 10.0 volts?All
Ye s®Go To 5
No®Repair the open Fused Ignition Switch Output Circuit.
Perform Powertrain Verification Test VER-2A.
5 Ignition Off
Remove the Air Conditioning Clutch Relay.
Note: Check connectors - Clean/repair as necessary.
Using an ohmmeter, measure the resistance between terminals C (85) and A (86) of
the Air Conditioning Clutch Relay.
Is the resistance below between 50 to 90 ohms?All
Ye s®Go To 6
No®Replace the Air Conditioning Clutch Relay.
Perform Powertrain Verification Test VER-2A.
6 Ignition Off
Disconnect the PCM grey connector.
Note: Check connectors - Clean/repair as necessary.
Using an Ohmmeter, measure the A/C Clutch Control Circuit from the PCM
connector to ground.
Is the resistance below 5.0 ohms?All
Ye s®Repair the Air Conditioning Clutch Relay Control Circuit for a
short to ground.
Perform Powertrain Verification Test VER-2A.
No®Go To 7
7 Ignition Off
Disconnect the PCM grey connector.
Remove the Air Conditioning Clutch Relay.
Note: Check connectors - Clean/repair as necessary.
Using an ohmmeter, measure the resistance of the Air Conditioning Clutch Relay
Control Circuit from the relay to the PCM.
Is the resistance below 5.0 ohms?All
Ye s®Go To 8
No®Repair open Air Conditioning Clutch Relay Control Circuit.
Perform Powertrain Verification Test VER-2A.
8 Ignition Off
If there are no potential causes remaining, the PCM is assumed to be defective.
View repair options.All
Repair
Replace the PCM.
Perform Powertrain Verification Test VER-2A.
171
DRIVEABILITY
P-0645 A/C CLUTCH RELAY CIRCUIT ÐContinued
ProCarManuals.com

Symptom:
P-0703 BRAKE SWITCH STUCK PRESSED OR RELEASED
When Monitored and Set Condition:
P-0703 BRAKE SWITCH STUCK PRESSED OR RELEASED
When Monitored: With engine running. The PCM expects the signal to be high for 16
cycles while it monitors the brake switch signal during accel and decel modes.
Set Condition: After the vehicle speed increases, the PCM must accumulate 6 seconds
while delta throttle voltage is above 0.02 volt. The count is reset to zero whenever the
brake switch indicates a low signal.
POSSIBLE CAUSES
BRAKE SWITCH GROUND CIRCUIT OPEN
BRAKE SWITCH INTERNAL SHORT
BRAKE SWITCH SENSE CIRCUIT OPEN
BRAKE SWITCH SENSE CIRCUIT SHORT TO GROUND
PCM CONNECTOR OBSERVABLE DEFECT
PCM DEF (VOLTAGE HIGH)
PCM DEF (VOLTAGE LOW)
TEST ACTION APPLICABILITY
1 Ignition Off
Disconnect the Brake Switch Connector.
Note: Check connectors - Clean/repair as necessary.
Key on.
With a Voltmeter, measure the Brake Switch Sense Circuit at the Brake Switch
Connector.
Is the voltage above 9.0 volts?All
Ye s®Go To 2
No®Go To 5
2 Ignition Off
Disconnect the Brake Switch Connector.
Note: Check connectors - Clean/repair as necessary.
With an Ohmmeter, measure the Brake Switch Ground Circuit at the Brake Switch
Connector to ground.
Is the resistance below 5.0 ohms?All
Ye s®Go To 3
No®Repair the Brake Switch Ground Circuit.
Perform Powertrain Verification Test VER-2A.
172
DRIVEABILITY
ProCarManuals.com

TEST ACTION APPLICABILITY
3 Ignition off.
Disconnect the Brake Switch Connector.
Note: Check connectors - Clean/repair as necessary.
Ignition on with engine not running.
Monitor Brake Switch status on the DRB while performing the next step.
Connect a jumper across the Brake Switch Circuit to Ground Circuit.
Did the DRB change from9pressed9to9released9?All
Ye s®Replace or adjust the Brake Switch.
Perform Powertrain Verification Test VER-2A.
No®Go To 4
4 If there are no potential causes remaining, the Powertrain Control Module is
assumed to be defective.
View repair options.All
Repair
Replace the PCM.
Perform Powertrain Verification Test VER-2A.
5 Ignition Off
Disconnect the Powertrain Control Module.
Disconnect the Brake Switch Connector.
Note: Check connectors - Clean/repair as necessary.
With an Ohmmeter, measure the Brake Switch Sense Circuit resistance from the
PCM to the Brake Switch Connector.
Is the resistance below 5.0 ohms?All
Ye s®Go To 6
No®Repair the Brake Switch Sense Circuit for an open.
Perform Powertrain Verification Test VER-2A.
6 Ignition Off
Disconnect the Powertrain Control Module.
Note: Check connectors - Clean/repair as necessary.
Is any terminal damaged, pushed out, or miswired?All
Ye s®Repair as necessary.
Perform Powertrain Verification Test VER-2A.
No®Go To 7
7 Ignition Off
Disconnect the Powertrain Control Module.
Disconnect the Brake Switch Connector.
Note: Check connectors - Clean/repair as necessary.
With an Ohmmeter, measure the Brake Switch Sense Circuit to a good ground.
Is the resistance below 5.0 ohms?All
Ye s®Repair the Brake Switch Sense Circuit for a short to ground.
Perform Powertrain Verification Test VER-2A.
No®Go To 8
173
DRIVEABILITY
P-0703 BRAKE SWITCH STUCK PRESSED OR RELEASED ÐContinued
ProCarManuals.com

TEST ACTION APPLICABILITY
3 Ignition Off
Disconnect the Upstream Oxygen Sensor Connector.
Note: Check connectors - Clean/repair as necessary.
Using an Ohmmeter, measure the resistance from the O2 Sensor Ground Circuit to
a good ground.
Is the resistance below 5.0 ohms?All
Ye s®Go To 4
No®Repair the open Sensor Ground Circuit to the Upstream Oxygen
Sensor.
Perform Powertrain Verification Test VER-5A.
4 Ignition Off
Disconnect the Upstream Oxygen Sensor Connector.
Note: Check connectors - Clean/repair as necessary.
Inspect the Connectors and Terminals.
Is any Terminal damaged, pushed out or miswired?All
Ye s®Repair or replace as necessary.
Perform Powertrain Verification Test VER-5A.
No®Go To 5
5 Ignition Off
Disconnect the Powertrain Control Module Connector.
Note: Check connectors - Clean/repair as necessary.
Inspect the Connector.
Is the Connector condition OK?All
Ye s®Go To 6
No®Repair as necessary.
Perform Powertrain Verification Test VER-5A.
6 If there are no potential causes remaining, the Upstream Oxygen Sensor is assumed
to be defective.
View repair options.All
Repair
Replace the Upstream Oxygen Sensor.
Perform Powertrain Verification Test VER-5A.
176
DRIVEABILITY
P-1195 SLOW 1/1 O2S DURING CATALYST MONITOR ÐContinued
ProCarManuals.com

Symptom:
P-1281 ENGINE IS COLD TOO LONG
When Monitored and Set Condition:
P-1281 ENGINE IS COLD TOO LONG
When Monitored: Ignition key on, engine not running. Ambient temperature greater
than þ11ÉC (-11ÉF) and coolant temperature greater than þ7ÉC (19ÉF)
Set Condition: The engine does not warm to 79 degrees C (176 degrees F) while driving
for 20 minutes after start.
POSSIBLE CAUSES
ENGINE COLD TOO LONG
TEST ACTION APPLICABILITY
1 Start Engine
Drive vehicle under normal driving conditions for 20 minutes.
With the DRB, read Engine Coolant Temperature.
Did the engine warm to 79 degrees C (176 degrees F)?All
Ye s®Test Complete.
No®See pertinent service manual information for cooling system
diagnostics.
177
DRIVEABILITY
ProCarManuals.com

Symptom:
P1282 FUEL PUMP RELAY CONTROL CIRCUIT
When Monitored and Set Condition:
P±1282 FUEL PUMP RELAY CONTROL CIRCUIT
When Monitored: With the ignition key on and battery voltage greater than 10 volts.
Set Condition: An open or shorted condition is detected in the fuel pump relay control
circuit.
POSSIBLE CAUSES
FUSED IGNITION SWITCH OUTPUT CIRCUIT OPEN
FUEL PUMP RELAY DEFECTIVE
FUEL PUMP RELAY CONTROL CIRCUIT OPEN
FUEL PUMP RELAY CONTROL CIRCUIT SHORT TO GROUND
FUEL PUMP RELAY WIRING HARNESS INTER DEF
FUEL PUMP RELAY WIRING HARNESS OBS DEF
PCM DEFECTIVE
TEST ACTION APPLICABILITY
1 Ignition On, Engine Not Running
With the DRB, actuate the Fuel Pump Relay.
Is the Fuel Pump Relay clicking?All
Ye s®Go To 2
No®Go To 4
2 Ignition On, Engine Not Running
With the DRB actuate the Fuel Pump Relay.
Wiggle the Wiring Harness from the Relay to the PCM.
Did the Fuel Pump Relay clicking stop or become erratic while wiggling the wires?All
Ye s®Repair Circuit as necessary where wiggling caused the clicking to
become erratic.
Perform Powertrain Verification Test VER-2A.
No®Go To 3
3 Ignition Off
Using the schematic as a guide, inspect the Wiring and Connectors.
Were any problems found?All
Ye s®Repair as necessary.
Perform Powertrain Verification Test VER-2A.
No®Test Complete.
178
DRIVEABILITY
ProCarManuals.com

TEST ACTION APPLICABILITY
4 Ignition Off
Disconnect the Fuel Pump Relay.
Note: Check connectors - Clean/repair as necessary.
Ignition On, Engine Not Running
Using a Voltmeter, measure the Fused Ignition Switch Output Circuit.
Is the voltage above 10.0 volts?All
Ye s®Go To 5
No®Repair the open Fused Ignition Switch Output Circuit.
Perform Powertrain Verification Test VER-2A.
5 Ignition Off
Disconnect the Fuel Pump Relay.
Note: Check connectors - Clean/repair as necessary.
Using an Ohmmeter, measure across Terminals 85 and 86 of the Fuel Pump Relay for
resistance.
Is the resistance between 50 and 90 ohms?All
Ye s®Go To 6
No®Replace Fuel Pump Relay.
Perform Powertrain Verification Test VER-2A.
6 Ignition Off
Disconnect the Powertrain Control Module Connector.
Note: Check connectors - Clean/repair as necessary.
Disconnect the Fuel Pump Relay.
Note: Check connectors - Clean/repair as necessary
Using an Ohmmeter, measure the Fuel Pump Relay Control Circuit for resistance.
Is the resistance below 5.0 ohms?All
Ye s®Go To 7
No®Repair the open Fuel Pump Relay Control Circuit.
Perform Powertrain Verification Test VER-2A.
7 Ignition Off
Disconnect the PCM Connector.
Note: Check connectors - Clean/repair as necessary.
Disconnect the Fuel Pump Relay.
Note: Check connectors - Clean/repair as necessary.
Using an Ohmmeter, measure the Fuel Pump Relay Control Circuit to ground.
Is the resistance below 5.0 ohms?All
Ye s®Repair the Fuel Pump Relay Control Circuit for a short to ground.
Perform Powertrain Verification Test VER-2A.
No®Go To 8
8 Ignition off.
If there are no potential causes remaining, the PCM is assumed to be defective.
View repair options.All
Repair
Replace the PCM.
Perform Powertrain Verification Test VER-2A.
179
DRIVEABILITY
P1282 FUEL PUMP RELAY CONTROL CIRCUIT ÐContinued
ProCarManuals.com

Symptom:
P-1294 TARGET IDLE NOT REACHED
When Monitored and Set Condition:
P-1294 TARGET IDLE NOT REACHED
When Monitored: Engine idling more than 2.8 seconds and coolant temp greater than 70
degrees C (160 degrees F). For an automatic transmission, in drive mode. There must not
be a MAP Sensor or TP Sensor or speed sensor trouble code.
Set Condition: Engine idle is > 200 RPM above target idle speed or less than 100 RPM
below target idle speed for 20 seconds. Two consecutive failures in a row will store this
trouble code.
POSSIBLE CAUSES
ENG VACUUM HOSES AND COMPONENTS LEAKS
THROTTLE BODY DEFECTIVE
THROTTLE PLATE/LINKAGE NOT IN CORRECT POS
IAC WIRING HARNESS INTERMITTENT DEFECT
IAC WIRING HARNESS OBSERVABLE DEFECTIVE
TEST ACTION APPLICABILITY
1 Ignition Off
Does the engine exhibit a start and stall condition?All
Ye s®Go To 2
No®Go To 4
2 Ignition Off
Perform minimum air flow test that is described in the service information.
Is the idle RPM within the range shown in the chart?All
Ye s®Test Complete.
No®Go To 3
180
DRIVEABILITY
ProCarManuals.com