fuse CHRYSLER VOYAGER 2000 Diagnostic Manual

Symptom List:
P-1696 PCM FAILURE EEPROM WRITE DENIED
P-1697 PCM FAILURE SRI MILE NOT STORED
Test Note: All symptoms listed above are diagnosed using the same tests.
The title for the tests will be P-1696 PCM FAILURE EEPROM
WRITE DENIED.
POSSIBLE CAUSES
POWERTRAIN CONTROL MODULE DEFECTIVE9WRITE REFUSED9
SRI MEMORY / INSTRUMENT PANEL ODO MILEAGE SAME
SRI MEMORY9SRI MILEAGE INVALID9
SRI MEMORY NEEDS UPDATING
PCM DEFECTIVE9WRITE FAILURE9
TEST ACTION APPLICABILITY
1 Ignition on, engine not running.
With the DRB, perform the SRI Memory Test.
Does the DRB display9Write Refused9?All
Ye s®Go To 2
No®Go To 4
2 Ignition on, engine not running.
With the DRB, perform the SRI Memory Test.
Does the DRB display9Write Failure?9All
Ye s®Replace the Powertrain Control Module.
Perform Verification Test VER-2A.
No®Go To 3
3 Ignition on, engine not running.
With the DRB, perform the SRI Memory Test.
Note: Retest the SRI Memory two more times when necessary.
Did the trouble code9Write Refused9return?All
Ye s®Replace the Powertrain Control Module.
Perform Powertrain Verification Test VER-2A.
No®Test Complete.
4 Ignition on, engine not running.
With the DRB, perform the SRI Memory Test.
Does the DRB display9SRI Mileage Invalid?9All
Ye s®Update the mileage and retest the SRI Memory.
Perform Powertrain Verification Test VER-2A.
No®Go To 5
222
DRIVEABILITY
ProCarManuals.com

Symptom:
* CHECKING PCM POWER AND GROUND CIRCUITS
POSSIBLE CAUSES
OPEN PCM GROUND CIRCUIT AT CAVITY 10
FUSED IGNITION SWITCH OUTPUT CIRCUIT OPEN
OPEN PCM GROUND CIRCUIT AT CAVITY 50
TEST ACTION APPLICABILITY
1 Ignition Off
Disconnect the PCM Connector.
Note: Check connectors - Clean/repair as necessary.
With an Ohmmeter, measure the ground circuits at cavities 10 and 50.
Is the resistance below 5.0 ohms?All
Ye s®Go To 2
No®Repair the open ground circuit(s).
Perform Verification Test VER-2A.
2 Ignition Off
Disconnect the PCM Connector.
Note: Check connectors - Clean/repair as necessary.
Turn Ignition on.
With a Voltmeter, measure the Fused Ignition Switch Output Circuit cavity 20.
Is the voltage above 10.0 volts?All
Ye s®Go To 3
No®Repair the open Fused Ignition Switch Output Circuit.
Perform Verification Test VER-2A.
3 Ignition Off
Disconnect the Powertrain Control Module Connector.
Note: Check connectors - Clean/repair as necessary.
Turn Ignition on.
Using a voltmeter, probe the fused B (+) circuit 46.
Is the voltage above 10.0 volts?All
Ye s®Test Complete.
No®Repair the open fused B (+) circuit.
Perform Verification Test VER-2A.
251
DRIVEABILITY
ProCarManuals.com

Symptom:
*(NO RESPONSE(CONDITION
POSSIBLE CAUSES
IGNITION NOT ON
DIAGNOSTIC READ-OUT BOX ADAPTER CABLE DEFECTIVE
FUEL PUMP DEFECTIVE
FUSED IGNITION SWITCH OUTPUT CIRCUIT OPEN
PCM GROUNDS OPEN
FUEL PUMP RELAY OUT CKT INTERMITTENT SHORT TO GRND
FUEL PUMP RELAY OUTPUT CIRCUIT SHORT TO GROUND
SCI RECEIVE CIRCUIT OPEN
SCI RECEIVE CIRCUIT SHORT TO GROUND
SCI TRANSMIT CIRCUIT OPEN
SCI TRANSMIT CIRCUIT SHORTED TO GROUND
FUSED B(+) CIRCUIT OPEN BETWEEN FUSE AND BATTERY
DIAGNOSTIC READ-OUT BOX DEFECTIVE
PCM DEFECTIVE (NO RESPONSE)
FUSED B(+) CIRCUIT OPEN BETWEEN FUSE AND PCM
FUSED B(+) CIRCUIT SHORT TO GROUND
TEST ACTION APPLICABILITY
1 Attempt to start vehicle.
Does the vehicle start?All
Ye s®Go To 2
No®Go To 12
2 Was the Ignition on when the ªNo Responseº message was displayed? All
Ye s®Go To 3
No®Turn the ignition on to get a response.
3 Ignition off.
Using an Ohmmeter, measure the DLC ground circuit (terminals 4 and 5) to ground.
Is the resistance below 5.0 ohms for each measurement?All
Ye s®Go To 4
No®Repair the open ground circuit(s).
Perform Powertrain Verification Test VER-1A.
272
STARTING
ProCarManuals.com

TEST ACTION APPLICABILITY
9 Ignition Off.
Connect the DRB to a functional Data Link Connector on another vehicle.
Turn the ignition on.
With the DRB, attempt to read trouble codes.
Did the DRB display ªNo Responseº?All
Ye s®Go To 10
No®Replace the initial vehicle's Powertrain Control Module.
Perform Powertrain Verification Test VER-1A.
10 Ignition Off.
Substitute another DRB Adapter Cable.
Ignition on, Engine not running.
With the DRB, attempt to read trouble codes.
Did the DRB display ªNo Responseº?All
Ye s®Go To 11
No®Replace the DRB Adapter Cable.
Perform Powertrain Verification Test VER-1A.
11 If there are no potential causes remaining, the Diagnostic Readout Box is assumed to
be defective.
View repair options.All
Repair
Have the DRB repaired or replaced.
Perform Powertrain Verification Test VER-1A.
12 Ignition Off.
Disconnect the TP Sensor Connector.
Note: Check connector-Clean/repair as necessary.
Turn the ignition on.
With a voltage, measure the Throttle Position Sensor 5±volt Supply circuit.
Is the voltage above 6.0 volts?All
Ye s®Repair the open grounds at the Powertrain Control Module
Cavities 10 and 50.
Perform the Powertrain Verification Test VER-1A
No®Go To 13
13 Ignition Off.
Disconnect the Powertrain Control Module.
Note: Check connector-Clean/repair as necessary.
Turn the ignition on.
With a voltmeter, measure Fused Ignition Switch Output Circuit.
Is the voltage above 10.0 volts?All
Ye s®Go To 14
No®Repair the open Fused Ignition Switch Output Circuit (check
Ignition Switch Fuse in PDC).
Perform Powertrain Verification Test VER-1A.
274
STARTING
*(NO RESPONSE(CONDITION ÐContinued
ProCarManuals.com

TEST ACTION APPLICABILITY
14 Ignition Off.
Disconnect the Powertrain Control Module.
Note: Check connectors - Clean/repair as necessary.
Turn the ignition on.
With a voltmeter, mesure the Fused B(+) Curcuit.
Is the voltage above 10.0 volts?All
Ye s®Go To 15
No®Go To 16
15 If there are no potential causes remaining, replace the Powertrain Control Module.
View repair options.All
Replace the Powertrain Control Module.
Perform the Powertrain Verification Test VER-1A.
16 Remove Fuel Pump Fuse from the Power Distribution Center.
Inspect the Fuse.
Is the fuse OK?All
Ye s®Go To 17
No®Go To 18
17 Ignition On.
Remove the Fuel Pump Fuse from the PCM.
With a voltmeter, measure the B(+) side of the Fuse Socket.
Is the voltage above 10.0 volts?All
Ye s®Repair the opem B(+) circuit between the Fuse and the PCM.
Perform Powertrain Verification Test VER-1A.
No®Repair the opem B(+) circuit between the Fuse and the battery.
Perform Powertrain Verification Test VER-1A.
18 Ignition Off
Disconnect the Fuel Pump Relay.
Disconnect the Fuel Pump Electrical Connector.
Note: Check connectors - Clean/repair as necessary.
With an Ohmmeter, measure the Fuel Pump Relay Output Circuit to ground.
Is the resistance below 5.0 ohms?All
Ye s®Repair the Fuel Pump Relay Output Circuit for a short to ground.
Perform Powertrain Verification Test VER-1A.
No®Go To 19
19 If there are no potential causes remaining, the Fuel Pump is assumed to be defective.
View repair options.All
Repair
Replace the Fuel Pump. Replace Fuel Pump Fuse.
Perform Powertrain Verification Test VER-1A.
275
STARTING
*(NO RESPONSE(CONDITION ÐContinued
ProCarManuals.com

Symptom:
* CHECKING THE FUEL SYSTEM
POSSIBLE CAUSES
FUEL PUMP GROUND CIRCUIT OPEN
FUEL PUMP GROUND CIRCUIT OPEN
FUEL PUMP RELAY FUSED B(+) CIRCUIT OPEN
FUEL PUMP RELAY FUSED B(+) CIRCUIT OPEN
FUEL PUMP RELAY OUTPUT CIRCUIT OPEN
FUEL PUMP RELAY OUTPUT CIRCUIT OPEN
FUEL FILTER DEFECTIVE
FUEL FILTER DEFECTIVE
FUEL PUMP DEFECTIVE
FUEL PUMP DEFECTIVE
FUEL PUMP RELAY
FUEL PUMP RELAY
IN-TANK FUEL PRESSURE REGULATOR DEFECTIVE
IN-TANK FUEL PRESSURE REGULATOR DEFECTIVE
THROTTLE POSITION SENSOR DEFECTIVE
FUEL FILTER DEFECTIVE
FUEL FILTER DEFECTIVE
FUEL INLET STRAINER DEFECTIVE
FUEL INLET STRAINER DEFECTIVE
FUEL PUMP MODULE DEFECTIVE
FUEL PUMP MODULE DEFECTIVE
FUEL SUPPLY LINE DEFECTIVE
FUEL SUPPLY LINE DEFECTIVE
FUEL TUBE RESTRICTED
FUEL TUBE RESTRICTED
POWERTRAIN CONTROL MODULE DEFECTIVE
POWERTRAIN CONTROL MODULE DEFECTIVE
THROTTLE CABLES DEFECTIVE
THROTTLE CABLES DEFECTIVE
THROTTLE POSITION SENSOR DEFECTIVE
278
STARTING
ProCarManuals.com

TEST ACTION APPLICABILITY
15 Ignition Off.
Disconnect the Fuel Pump Relay.
Check connectors - Clean/repair as necessary.
Ignition On , Engine Not Running.
With a Voltmeter, measure the Fuel Pump Relay Fused B(+) Circuit.
Is the voltage above 10.0 volts?ENGINE - 3.0L V6
Ye s®Go To 16
No®Repair the open Fuel Pump Relay Fused B(+) Circuit.
Perform Powertrain Verification Test VER-1A.
16 Ignition Off.
Disconnect the Fuel Pump Harness Connector.
Note; Check Connectors - clean/repair as necessary.
Caution: It is critical that the Fuel Pump Connector has a clean and tight
connection.
Ignition On, Engine Not Running.
Actuate the ASD Fuel System test.
With a Voltmeter, measure the Fuel Pump Relay Output Circuit.
Is the voltage above 10.0 volts?ENGINE - 3.0L V6
Ye s®Go To 17
No®Repair the open Fuel Pump Relay Output Circuit.
Perform Powertrain Verification Test VER-1A.
17 Ignition Off.
Disconnect the Fuel Pump Relay.
Check connectors - Clean/repair as necessary.
Install a substitute Relay of the same part number for the Fuel Pump Relay.
Attempt to start the Engine.
Does the engine start?ENGINE - 3.0L V6
Ye s®Replace the Fuel Pump Relay.
Perform Powertrain Verification Test VER-1A.
No®Go To 18
18 Ignition off.
If there are no potential causes remaining, the Fuel Pump is assumed to be defective.
View repair options.ENGINE - 3.0L V6
Repair
Replace the Fuel Pump.
Perform Powertrain Verification Test VER-1A.
19Note: Ensure the SKIM has proper communication and that there are no
SKIM DTC's present before continuing.
Ignition Off.
Ensure the Throttle Cables are not holding the Throttle open.
Is the Throttle held open?ENGINE - 2.0L,
2.4L I-4 DOHC
and/or ENGINE -
3.3L V6 FFV and/or
ENGINE - 3.3L V6
and/or ENGINE -
3.8L V6
Ye s®Repair condition that holds the Throttle Body open.
No®Go To 20
282
STARTING
* CHECKING THE FUEL SYSTEM ÐContinued
ProCarManuals.com

TEST ACTION APPLICABILITY
28 Record the Fuel Pressure Gauge reading.
Ignition Key Off.
Warning: The Fuel System must be opened and may be under high pressure.
Release Fuel pressure.
Remove the Fuel Pressure Gauge.
Install adapter 6631 between Fuel Filter Outlet and Chassis Fuel Supply Tube.
Connect Fuel Pressure Gauge to adapter 6631.
Ignition On, Engine Not Running.
With DRB, actuate the ASD Fuel System.
Record the Fuel Pressure Gauge reading.
Compare this reading with the previous reading.
Is the fuel pressure at least 2 psi higher than the previous reading?ENGINE - 2.0L,
2.4L I-4 DOHC
and/or ENGINE -
3.3L V6 FFV and/or
ENGINE - 3.3L V6
and/or ENGINE -
3.8L V6
Ye s®Repair restriction in Chassis Fuel Supply Line between Fuel
Filter and Fuel Rail.
Perform Powertrain Verification Test VER-1A.
No®Go To 29
29 If there are no potential causes remaining, the Fuel Pump Module is assumed to be
defective.
View repair options.ENGINE - 2.0L,
2.4L I-4 DOHC
and/or ENGINE -
3.3L V6 FFV and/or
ENGINE - 3.3L V6
and/or ENGINE -
3.8L V6
Repair
Replace Fuel Pump Module.
Perform Powertrain Verification Test VER-1A.
30 Ignition Off.
Disconnect the Fuel Pump Harness Connector.
Note: Check connectors - Clean/repair as necessary.
Caution: It is critical that the Fuel Pump Connector has a clean and tight
connection.
With an Ohmmeter, measure the Fuel Pump Ground Circuit.
Is the resistance below 5.0 ohms?ENGINE - 2.0L,
2.4L I-4 DOHC
and/or ENGINE -
3.3L V6 FFV and/or
ENGINE - 3.3L V6
and/or ENGINE -
3.8L V6
Ye s®Go To 31
No®Repair the open Fuel Pump Ground Circuit.
Perform Powertrain Verification Test VER-1A.
31 Ignition Off.
Disconnect the Fuel Pump Relay.
Check connectors - Clean/repair as necessary.
Ignition On , Engine Not Running.
With a Voltmeter, measure the Fuel Pump Relay Fused B(+) Circuit.
Is the voltage above 10.0 volts?ENGINE - 2.0L,
2.4L I-4 DOHC
and/or ENGINE -
3.3L V6 FFV and/or
ENGINE - 3.3L V6
and/or ENGINE -
3.8L V6
Ye s®Go To 32
No®Repair the open Fuel Pump Relay Fused B(+) Circuit.
Perform Powertrain Verification Test VER-1A.
285
STARTING
* CHECKING THE FUEL SYSTEM ÐContinued
ProCarManuals.com

Symptom:
* CHECKING THE SECONDARY IGNITION SYSTEM
POSSIBLE CAUSES
GOOD SPARK AT SPARK PLUG #1
AUTO SHUTDOWN RELAY OUTPUT CIRCUIT OPEN
AUTO SHUTDOWN RELAY OUTPUT CIRCUIT OPEN
COIL SECONDARY CABLE DEFECTIVE
FUSED B(+) CIRCUIT OPEN
FUSED B(+) CIRCUIT OPEN
IGNITION COIL CONNECTOR OBSERVABLE DEFECT
IGNITION COIL CONNECTOR OBSERVABLE DEFECT
IGNITION COIL DEFECTIVE
IGNITION COIL SECONDARY CABLE #1 DEFECTIVE
IGNITION COIL SECONDARY CABLE #4 DEFECTIVE
SECONDARY IGNITION COMPONENT(S) DEFECTIVE
SPARK PLUG CABLE #1 DEFECTIVE
AUTO SHUTDOWN RELAY DEFECTIVE
AUTO SHUTDOWN RELAY DEFECTIVE
IGNITION COIL DEFECTIVE
IGNITION COIL DEFECTIVE (RESISTANCE OUT OF RANGE)
SPARK PLUG #1 OR #4 DEFECTIVE
GOOD SPARK AT SPARK PLUG #1
GOOD SPARK AT SPARK PLUG #1
TEST ACTION APPLICABILITY
1 Ignition Off.
Disconnect the Spark Plug Cable at Spark Plug #1.
Connect the Cable to a Spark Tester.
Connect the Spark Tester to a good Ground.
Warning: Ensure that there are no Fuel or Fuel vapors present in or near
the Engine compartment before continuing with the test.
While cranking the Engine for 10 seconds, watch for spark.
Is there good spark?ENGINE - 3.0L V6
Ye s®Refer to Symptom list for further diagnostic tests.
No®Go To 2
288
STARTING
ProCarManuals.com

TEST ACTION APPLICABILITY
12 Ignition Off.
Disconnect the Ignition Coil Connector.
Note: Check connectors - Clean/repair as necessary.
Disconnect the ASD Relay.
Note: Check connectors - Clean/repair as necessary.
Using a Jumper Wire connect the ASD Relay Output Circuit to Ground at the
Ignition Coil Connector.
With an Ohmmeter mesaure the ASD Output Circuit for resistance to Ground at the
Relay.
Is the resistance below 5.0 ohms?ENGINE - 3.0L V6
Ye s®Go To 13
No®Repair open ASD Relay Output Circuit.
Perform Powetrain Verification Test VER-1A.
13 Ignition Off.
Disconnect the ASD Relay.
Note: Check connectors - Clean/repair as necessary.
Ignition On, Engine Not Running.
With a Voltmeter, measure the Fused B(+) Circuit cavity B in ASD Relay Connector.
Is the voltage above 10 volts?ENGINE - 3.0L V6
Ye s®Replace the Auto Shutdown Relay.
Perform Powertrain Verification Test VER-1A.
No®Repair open Fused B+.
Perform Verification TEST VER-1A
14 Ignition Off.
Remove the Distributor Cap.
Is the Distributor Rotor loose?ENGINE - 3.0L V6
Ye s®Repair loose Distributor Rotor as necessary.
Perform Verification TEST VER-1A
No®Go To 15
15 If there are no potential causes remaining, the Distributor Drive System is assumed
to be defective.
View repair options.ENGINE - 3.0L V6
Repair
Repair the Distributor Drive System.
Perform Powertrain Verification Test VER-1A.
16 Ignition Off.
Disconnect the Spark Plug Cable at Spark Plug #1.
Connect the Cable to a Spark Tester.
Connect the Spark Tester to a good Ground.
Warning: Ensure that there are no Fuel or Fuel vapors present in or near
the Engine compartment before continuing with the test.
While cranking the Engine for 10 seconds, watch for spark.
Is there good spark?ENGINE - 2.0L
and 2.4L I-4 DOHC
Ye s®Refer to Symptom list for further diagnostic tests.
No®Go To 17
291
STARTING
* CHECKING THE SECONDARY IGNITION SYSTEM ÐContinued
ProCarManuals.com