warning CHRYSLER VOYAGER 2000 Diagnostic Manual

TEST ACTION APPLICABILITY
10 Ignition Off.
Warning: The Fuel System must be opened and may be under high pressure.
Release Fuel pressure.
Remove the Fuel Pump Module.
Inspect the Fuel Pump Inlet Strainer.
Is the Inlet Strainer plugged?ENGINE - 3.0L V6
Ye s®Replace the Fuel Inlet Strainer.
Perform Powertrain Verification Test VER-1A.
No®Go To 11
11 Record the Fuel Pressure Gauge reading.
Ignition key off.
Warning: The Fuel System must be opened and may be under high pressure.
Release Fuel pressure.
Remove the Fuel Pressure Gauge.
Remove Fuel Pressure Gauge Adapter 6433 and reconnect Fuel Line to Fuel Rail.
Install adapter 6631 between Fuel Filter Outlet and Chassis Fuel Supply Tube.
Connect Fuel Pressure Gauge to adapter 6631.
Ignition On, Engine Not Running.
With DRB, actuate the ASD Fuel System.
Record the Fuel Pressure Gauge reading.
Compare this reading with the previous reading.
Is the fuel pressure at least 2 psi higher than the previous reading?ENGINE - 3.0L V6
Ye s®Repair restriction in Chassis Fuel Supply Line between Fuel
Filter and Fuel Rail.
Perform Powertrain Verification Test VER-1A.
No®Go To 12
12 If there are no potential causes remaining, the Fuel Pump Module is assumed to be
defective.
View repair options.ENGINE - 3.0L V6
Repair
Replace Fuel Pump Module.
Perform Powertrain Verification Test VER-1A.
13 Ignition On, Engine Not Running
With DRB, read Throttle Position Sensor voltage.
Is the voltage above 1.5 volts?ENGINE - 3.0L V6
Ye s®Disconnect the TP Sensor Conn. Replace Throttle Position Sensor.
Perform Powertrain Verification Test VER-1A.
No®Go To 14
14 Ignition Off.
Disconnect the Fuel Pump Harness Connector.
Note: Check connectors - Clean/repair as necessary.
Caution: It is critical that the Fuel Pump Connector has a clean and tight
connection.
With an Ohmmeter, measure the Fuel Pump Ground Circuit.
Is the resistance below 5.0 ohms?ENGINE - 3.0L V6
Ye s®Go To 15
No®Repair the open Fuel Pump Ground Circuit.
Perform Powertrain Verification Test VER-1A.
281
STARTING
* CHECKING THE FUEL SYSTEM ÐContinued
ProCarManuals.com

TEST ACTION APPLICABILITY
20 Ignition On, Engine Not Running
With the DRB, actuate the Fuel System and check for Fuel Pump operation at the
Fuel Tank.
Is the Fuel Pump operating?ENGINE - 2.0L,
2.4L I-4 DOHC
and/or ENGINE -
3.3L V6 FFV and/or
ENGINE - 3.3L V6
and/or ENGINE -
3.8L V6
Ye s®Go To 21
No®Go To 30
21 Ignition Off.
Warning: The Fuel System must be opened and may be under high pressure.
Relieve Fuel pressure.
Install a Fuel Pressure Gauge to the Fuel Rail.
Note: The Fuel Tank must be at least 1/4 full for the following tests.
Ignition On, Engine Not Running.
With the DRB, actuate the Fuel System.
Read the Fuel Pressure Gauge.
For 3.3 liter engines fuel pressure should be 50 to 60 psi, and for all other engines fuel
pressure should be 43 to 53 psi.
Is the Fuel pressure above the specification ?ENGINE - 2.0L,
2.4L I-4 DOHC
and/or ENGINE -
3.3L V6 FFV and/or
ENGINE - 3.3L V6
and/or ENGINE -
3.8L V6
Ye s®Go To 22
No®Go To 25
22 Ignition Off.
Warning: The Fuel System must be opened and may be under high pressure.
Release the Fuel pressure.
Inspect Fuel Filter for a restriction.
Is there a restriction?ENGINE - 2.0L,
2.4L I-4 DOHC
and/or ENGINE -
3.3L V6 FFV and/or
ENGINE - 3.3L V6
and/or ENGINE -
3.8L V6
Ye s®Replace the Fuel Filter.
Perform Powertrain Verification Test VER-1A.
No®Go To 23
23 Ignition Off.
Warning: The Fuel System must be opened and may be under high pressure.
Release the Fuel pressure.
Inspect Fuel Filter for a restriction.
Is there a restriction ?ENGINE - 2.0L,
2.4L I-4 DOHC
and/or ENGINE -
3.3L V6 FFV and/or
ENGINE - 3.3L V6
and/or ENGINE -
3.8L V6
Ye s®Go To 24
No®Replace the Fuel Pressure Regulator.
Perform Powertrain Verification Test VER-1A.
283
STARTING
* CHECKING THE FUEL SYSTEM ÐContinued
ProCarManuals.com

TEST ACTION APPLICABILITY
24 Ignition Off.
Warning: The Fuel System must be opened and may be under high pressure.
Release the Fuel pressure.
Inspect Fuel Return Tube for restriction between fuel Filter and Fuel Pump Module.
Is there a restriction ?ENGINE - 2.0L,
2.4L I-4 DOHC
and/or ENGINE -
3.3L V6 FFV and/or
ENGINE - 3.3L V6
and/or ENGINE -
3.8L V6
Ye s®Replace restricted Fuel Tube.
Perform Powertrain Verification Test VER-1A.
No®Test Complete.
25 Ignition Off.
Warning: The Fuel System must be opened and may be under high pressure.
Relieve Fuel pressure.
Tee-In a Fuel Pressure Gauge into the Fuel Hose using tool #6433.
Note: The Fuel Tank must be at least 1/4 full for the following tests.
Ignition On, Engine Not Running.
With the DRB, actuate the Fuel System.
Read the Fuel Pressure Gauge.
Fuel pressure should be 43 to 53 PSI for Gasoline, 50 to 60 PSI for (E85) Ethanol.
Is the Fuel pressure below the specification ?ENGINE - 2.0L,
2.4L I-4 DOHC
and/or ENGINE -
3.3L V6 FFV and/or
ENGINE - 3.3L V6
and/or ENGINE -
3.8L V6
Ye s®Go To 26
No®Test Complete.
26 Ignition Off.
Warning: The Fuel System must be opened and may be under high pressure.
Release Fuel pressure.
Remove adapter 6631 and reinstall Fuel Line.
Install adapter 6631 between Fuel Pump and Fuel Filter.
Connect Fuel Pressure Gauge to adapter 6631.
Key On.
With the DRB, actuate Fuel System.
Is the fuel pressure at least 2 psi higher than the previous reading?ENGINE - 2.0L,
2.4L I-4 DOHC
and/or ENGINE -
3.3L V6 FFV and/or
ENGINE - 3.3L V6
and/or ENGINE -
3.8L V6
Ye s®Replace the Fuel Filter.
Perform Powertrain Verification Test VER-1A.
No®Go To 27
27 Ignition Off.
Warning: The Fuel System must be opened and may be under high pressure.
Release Fuel pressure.
Remove the Fuel Pump Module.
Inspect the Fuel Pump Inlet Strainer.
Is the Inlet Strainer plugged?ENGINE - 2.0L,
2.4L I-4 DOHC
and/or ENGINE -
3.3L V6 FFV and/or
ENGINE - 3.3L V6
and/or ENGINE -
3.8L V6
Ye s®Replace the Fuel Inlet Strainer.
Perform Powertrain Verification Test VER-1A.
No®Go To 28
284
STARTING
* CHECKING THE FUEL SYSTEM ÐContinued
ProCarManuals.com

TEST ACTION APPLICABILITY
28 Record the Fuel Pressure Gauge reading.
Ignition Key Off.
Warning: The Fuel System must be opened and may be under high pressure.
Release Fuel pressure.
Remove the Fuel Pressure Gauge.
Install adapter 6631 between Fuel Filter Outlet and Chassis Fuel Supply Tube.
Connect Fuel Pressure Gauge to adapter 6631.
Ignition On, Engine Not Running.
With DRB, actuate the ASD Fuel System.
Record the Fuel Pressure Gauge reading.
Compare this reading with the previous reading.
Is the fuel pressure at least 2 psi higher than the previous reading?ENGINE - 2.0L,
2.4L I-4 DOHC
and/or ENGINE -
3.3L V6 FFV and/or
ENGINE - 3.3L V6
and/or ENGINE -
3.8L V6
Ye s®Repair restriction in Chassis Fuel Supply Line between Fuel
Filter and Fuel Rail.
Perform Powertrain Verification Test VER-1A.
No®Go To 29
29 If there are no potential causes remaining, the Fuel Pump Module is assumed to be
defective.
View repair options.ENGINE - 2.0L,
2.4L I-4 DOHC
and/or ENGINE -
3.3L V6 FFV and/or
ENGINE - 3.3L V6
and/or ENGINE -
3.8L V6
Repair
Replace Fuel Pump Module.
Perform Powertrain Verification Test VER-1A.
30 Ignition Off.
Disconnect the Fuel Pump Harness Connector.
Note: Check connectors - Clean/repair as necessary.
Caution: It is critical that the Fuel Pump Connector has a clean and tight
connection.
With an Ohmmeter, measure the Fuel Pump Ground Circuit.
Is the resistance below 5.0 ohms?ENGINE - 2.0L,
2.4L I-4 DOHC
and/or ENGINE -
3.3L V6 FFV and/or
ENGINE - 3.3L V6
and/or ENGINE -
3.8L V6
Ye s®Go To 31
No®Repair the open Fuel Pump Ground Circuit.
Perform Powertrain Verification Test VER-1A.
31 Ignition Off.
Disconnect the Fuel Pump Relay.
Check connectors - Clean/repair as necessary.
Ignition On , Engine Not Running.
With a Voltmeter, measure the Fuel Pump Relay Fused B(+) Circuit.
Is the voltage above 10.0 volts?ENGINE - 2.0L,
2.4L I-4 DOHC
and/or ENGINE -
3.3L V6 FFV and/or
ENGINE - 3.3L V6
and/or ENGINE -
3.8L V6
Ye s®Go To 32
No®Repair the open Fuel Pump Relay Fused B(+) Circuit.
Perform Powertrain Verification Test VER-1A.
285
STARTING
* CHECKING THE FUEL SYSTEM ÐContinued
ProCarManuals.com

Symptom:
* CHECKING THE SECONDARY IGNITION SYSTEM
POSSIBLE CAUSES
GOOD SPARK AT SPARK PLUG #1
AUTO SHUTDOWN RELAY OUTPUT CIRCUIT OPEN
AUTO SHUTDOWN RELAY OUTPUT CIRCUIT OPEN
COIL SECONDARY CABLE DEFECTIVE
FUSED B(+) CIRCUIT OPEN
FUSED B(+) CIRCUIT OPEN
IGNITION COIL CONNECTOR OBSERVABLE DEFECT
IGNITION COIL CONNECTOR OBSERVABLE DEFECT
IGNITION COIL DEFECTIVE
IGNITION COIL SECONDARY CABLE #1 DEFECTIVE
IGNITION COIL SECONDARY CABLE #4 DEFECTIVE
SECONDARY IGNITION COMPONENT(S) DEFECTIVE
SPARK PLUG CABLE #1 DEFECTIVE
AUTO SHUTDOWN RELAY DEFECTIVE
AUTO SHUTDOWN RELAY DEFECTIVE
IGNITION COIL DEFECTIVE
IGNITION COIL DEFECTIVE (RESISTANCE OUT OF RANGE)
SPARK PLUG #1 OR #4 DEFECTIVE
GOOD SPARK AT SPARK PLUG #1
GOOD SPARK AT SPARK PLUG #1
TEST ACTION APPLICABILITY
1 Ignition Off.
Disconnect the Spark Plug Cable at Spark Plug #1.
Connect the Cable to a Spark Tester.
Connect the Spark Tester to a good Ground.
Warning: Ensure that there are no Fuel or Fuel vapors present in or near
the Engine compartment before continuing with the test.
While cranking the Engine for 10 seconds, watch for spark.
Is there good spark?ENGINE - 3.0L V6
Ye s®Refer to Symptom list for further diagnostic tests.
No®Go To 2
288
STARTING
ProCarManuals.com

TEST ACTION APPLICABILITY
12 Ignition Off.
Disconnect the Ignition Coil Connector.
Note: Check connectors - Clean/repair as necessary.
Disconnect the ASD Relay.
Note: Check connectors - Clean/repair as necessary.
Using a Jumper Wire connect the ASD Relay Output Circuit to Ground at the
Ignition Coil Connector.
With an Ohmmeter mesaure the ASD Output Circuit for resistance to Ground at the
Relay.
Is the resistance below 5.0 ohms?ENGINE - 3.0L V6
Ye s®Go To 13
No®Repair open ASD Relay Output Circuit.
Perform Powetrain Verification Test VER-1A.
13 Ignition Off.
Disconnect the ASD Relay.
Note: Check connectors - Clean/repair as necessary.
Ignition On, Engine Not Running.
With a Voltmeter, measure the Fused B(+) Circuit cavity B in ASD Relay Connector.
Is the voltage above 10 volts?ENGINE - 3.0L V6
Ye s®Replace the Auto Shutdown Relay.
Perform Powertrain Verification Test VER-1A.
No®Repair open Fused B+.
Perform Verification TEST VER-1A
14 Ignition Off.
Remove the Distributor Cap.
Is the Distributor Rotor loose?ENGINE - 3.0L V6
Ye s®Repair loose Distributor Rotor as necessary.
Perform Verification TEST VER-1A
No®Go To 15
15 If there are no potential causes remaining, the Distributor Drive System is assumed
to be defective.
View repair options.ENGINE - 3.0L V6
Repair
Repair the Distributor Drive System.
Perform Powertrain Verification Test VER-1A.
16 Ignition Off.
Disconnect the Spark Plug Cable at Spark Plug #1.
Connect the Cable to a Spark Tester.
Connect the Spark Tester to a good Ground.
Warning: Ensure that there are no Fuel or Fuel vapors present in or near
the Engine compartment before continuing with the test.
While cranking the Engine for 10 seconds, watch for spark.
Is there good spark?ENGINE - 2.0L
and 2.4L I-4 DOHC
Ye s®Refer to Symptom list for further diagnostic tests.
No®Go To 17
291
STARTING
* CHECKING THE SECONDARY IGNITION SYSTEM ÐContinued
ProCarManuals.com

TEST ACTION APPLICABILITY
26 Ignition Off.
Disconnect the Spark Plug Cable at Spark Plug #1.
Connect the Cable to a Spark Tester.
Connect the Spark Tester to a good Ground.
Warning: Ensure that there are no Fuel or Fuel vapors present in or near
the Engine compartment before continuing with the test.
While cranking the Engine for 10 seconds, watch for spark.
Is there good spark?ENGINE - 2.0L,
2.4L I-4 DOHC
and/or ENGINE -
3.3L V6 and/or EN-
GINE - 3.8L V6
and/or ENGINE -
3.3L V6 FFV
Ye s®Refer to Symptom list for further diagnostic tests.
No®Go To 27
27 Ignition Off.
Disconnect the Spark Plug Cable at Spark Plug #2.
Connect the other end of the Cable to a Spark Tester.
Connect the Spark Tester to a good Ground.
Ensure that there are no fuel or fuel vapors present in or near the Engine
Compartment before continuing with the test.
While cranking the Engine for 10 seconds, watch for spark.
Is there good spark?ENGINE - 2.0L,
2.4L I-4 DOHC
and/or ENGINE -
3.3L V6 and/or EN-
GINE - 3.8L V6
and/or ENGINE -
3.3L V6 FFV
Ye s®Go To 28
No®Go To 29
28 Ignition Off.
Disconnect the Spark Plug Cable at Spark Plug #2.
Connect the other end of the Cable to a Spark Tester.
Connect the Spark Tester to a good Ground.
Ensure that there are no fuel or fuel vapors present in or near the Engine
Compartment before continuing with the test.
While cranking the Engine for 10 seconds, watch for spark.
Is there good spark?ENGINE - 2.0L,
2.4L I-4 DOHC
and/or ENGINE -
3.3L V6 and/or EN-
GINE - 3.8L V6
and/or ENGINE -
3.3L V6 FFV
Ye s®Replace Spark Plug Cable that was initially used to test for spark.
Perform Powertrain Verification Test VER-1A.
No®Test Complete.
29 Ignition Off.
Disconnect the Ignition Coil Connector.
Note: Check connectors - Clean/repair as necessary.
Inspect Terminals.
Is any Terminal damaged, pushed out, or miswired?ENGINE - 2.0L,
2.4L I-4 DOHC
and/or ENGINE -
3.3L V6 and/or EN-
GINE - 3.8L V6
and/or ENGINE -
3.3L V6 FFV
Ye s®Repair Terminal(s) for damage, pushout, or miswiring.
Perform Powertrain Verification Test VER-1A.
No®Go To 30
294
STARTING
* CHECKING THE SECONDARY IGNITION SYSTEM ÐContinued
ProCarManuals.com

Symptom:
* NO CRANK CONDITION
POSSIBLE CAUSES
BATTERY CIRCUIT RESISTANCE TOO HIGH
FUSED B(+) CIRCUIT OPEN
STARTER RELAY CONTROL CIRCUIT OPEN
STARTER RELAY OUTPUT CIRCUIT OPEN
CRANKSHAFT NOT ABLE TO ROTATE
STARTER MOTOR DEFECTIVE
PCM DEFECTIVE (NO CRANK CONDITION)
STARTER RELAY DEFECTIVE (RESISTANCE <=100 OHMS)
STARTER RELAY DEFECTIVE (RESISTANCE ABOVE 100 OHMS)
IGNITION SWITCH OUTPUT CIRCUIT OPEN
PARK/NEUTRAL SWITCH DEFECTIVE
TEST ACTION APPLICABILITY
1Note: Ensure the SKIM has proper communication and that there are no
SKIM DTC's present before continuing.
Ignition Off.
Disconnect the Starter Relay Connector.
Note: Check connectors - Clean/repair as necessary.
Warning: The Transmission must be in Park and the Parking Brake must be
on for the next step.
Warning: The engine may be cranked in the next step. Keep away from
moving parts.
Briefly connect a jumper wire between Starter Relay Output and Fused B(+)
Circuits.
Did the Starter Motor crank the Engine?All
Ye s®Go To 2
No®Go To 9
2 Ignition Off.
Disconnect the Starter Relay Connector.
Note: Check connectors - Clean/repair as necessary.
With a Voltmeter, measure the Fused B(+) Circuit.
Is the voltage above 11.6 volts?All
Ye s®Go To 3
No®Repair open Fused B(+) Circuit. (check Ignition Switch Fuse in
PDC).
Perform Powertrain Verification Test VER-1A.
296
STARTING
ProCarManuals.com

TEST ACTION APPLICABILITY
3 Ignition Off.
Ensure the Transmission is in Park.
With the DRB, read the Park/Neutral Position Switch.
Does the Switch show Park?All
Ye s®Go To 4
No®Repair Park/Neutral Switch.
Perform Powertrain Verification Test VER-1A.
4 Ignition Off.
Disconnect the Starter Relay Connector.
Note: Check connectors - Clean/repair as necessary.
Using an ohmmeter, test the Starter Relay Terminals for resistance.
Is the resistance above 100 ohms?All
Ye s®Replace the Starter Relay.
Perform Powertrain Verification Test VER-1A.
No®Go To 5
5 Ignition Off
Disconnect the Starter Relay Connector.
Note: Check connectors - Clean/repair as necessary.
With a voltmeter, probe Ignition Switch Output Circuit.
While attempting to crank the engine, read the Voltmeter.
Is the voltage above 10 volts?All
Ye s®Go To 6
No®Repair the open Ignition Switch Output (Start) Circuit.
Perform Powertrain Verification Test VER-1A.
6 Ignition Off.
Disconnect the Starter Relay Connector.
Disconnect the Powertrain Control Module.
Note: Check connectors - Clean/repair as necessary.
With an ohmmeter, test the Starter Relay Control Circuit for resistance.
Is the resistance above 5.0 ohms?All
Ye s®Repair the open Starter Relay Control Circuit.
Perform Powertrain Verification Test VER-1A.
No®Go To 7
7 Ignition Off
Disconnect the Powertrain Control Module.
Note: Check connectors - Clean/repair as necessary.
Warning: The Transmission must be in park and the Parking Brake must be
on for the next step.
Warning: The Engine may be cranked in the next step. Keep away form
moving Engine parts.
Connect a jumper wire between the Starter Relay Control Circuit and ground.
Briefly turn the Ignition to the crank position and then release.
Did the Engine crank?All
yes
Go To 8
no
Replace the Starter Relay.
Perform Powertrain Verification Test VER-1A.
297
STARTING
* NO CRANK CONDITION ÐContinued
ProCarManuals.com

TEST ACTION APPLICABILITY
8 If there are no potential causes remaining, the Powertrain Control Module is
assumed to be defective.
View repair options.All
Repair
Replace the Powertrain Control Module.
Perform Powertrain Verification Test VER-1A.
9 Ignition Off.
Ensure the Transmission is in Park.
With the DRB, read the Park/Neutral Position Switch.
Does the Switch show Park?All
Ye s®Go To 10
No®Repair Park/Neutral Switch.
Perform Powertrain Verification Test VER-1A.
10 Ignition Off
Disconnect the Starter Relay Connector.
Note: Check connectors - Clean/repair as necessary.
Warning: The Engine may be cranked in the next step. Keep away from
moving parts.
Warning: The engine may be cranked in the next step. Keep away from
moving parts.
Briefly connect a jumper wire between Starter Relay Output and Fused B(+)
Circuits.
Did the Starter Solenoid click when the jumper wire was connected?All
Ye s®Go To 11
No®Go To 15
11 Ignition Off
Check the Battery Cables for high resistance. (Use Service Manual procedure.)
Did either Battery Circuit have a voltage drop greater than 0.2 volt?All
Ye s®Repair the Battery Circuit for high resistance.
Perform Powertrain Verification Test VER-1A.
No®Go To 12
12 Ignition Off
Attempt to manually rotate the Crankshaft 360 degrees.
Is the Crankshaft able to rotate 360 degrees?All
Ye s®Go To 13
No®Repair the Engine mechanical problem as necessary.
Perform Powertrain Verification Test VER-1A.
13 Ignition Off.
Disconnect the Starter Relay Connector.
Note: Check connectors - Clean/repair as necessary.
With a Voltmeter, measure the Fused B(+) Circuit.
Is the voltage above 11.6 volts?All
Ye s®Go To 14
No®Repair open Fused B(+) Circuit. (check Ignition Switch Fuse in
PDC).
Perform Powertrain Verification Test VER-1A.
298
STARTING
* NO CRANK CONDITION ÐContinued
ProCarManuals.com