ACCESSORIES CHRYSLER VOYAGER 2000 Diagnostic Manual

NOTE:IF THREE ATTEMPTS ARE MADE TO
ENTER THE SECURE ACCESS MODE USING
AN INCORRECT PIN, SECURED ACCESS
MODE WILL BE LOCKED OUT FOR ONE
HOUR. TO EXIT THIS LOCKOUT MODE, TURN
THE IGNITION TO THE RUN POSITION FOR
ONE HOUR THEN ENTER THE CORRECT
PIN. (ENSURE ALL ACCESSORIES ARE
TURNED OFF. ALSO MONITOR THE
BATTERY STATE AND CONNECT A BATTERY
CHARGER IF NECESSARY).
5. Press ``ENTER'' to transfer the secret key (the
SKIM will send the secret key to the PCM).
3.2.10 PROGRAMMING THE SENTRY KEY
IMMOBILIZER MODULE
NOTE:IF THE PCM AND THE SKIM ARE
REPLACED AT THE SAME TIME, PROGRAM
THE VIN INTO THE PCM FIRST. ALL VEHICLE
KEYS WILL THEN NEED TO BE REPLACED
AND PROGRAMMMED TO THE NEW SKIM.
1. Turn the ignition on (transmission in park/
neutral).
2. Use the DRB and select ``THEFT ALARM'',
``SKIM'' then MISCELLLANEOUS.
3. Select ``SKIM MOSULE REPLACEMENT (GAS-
OLINE)''
4. Program the vehicle four-digit PIN into the
SKIM.
5. Select ``COUNTRY CODE'' and enter the correct
country.
NOTE:BE SURE TO ENTER THE CORRECT
COUNTRY CODE. IF THE INCORRECT
COUNTRY CODE IS PROGRAMMED INTO
SKIM, THE SKIM MUST BE REPLACED.
6. Select ``UPDATE VIN'' (the SKIM will learn the
VIN from the PCM).
7. Press ``ENTER'' to transfer the VIN (the PCM
will send the VIN to the SKIM).
8. The DRB will ask if you want to transfer the
secret key. Select ``ENTER'' to transfer secret key
from the PCM. This will ensure the current
vehicle ignition keys will still operate the SKIS
system.
3.2.11 PROGRAMMING THE IGNITION
KEYS TO THE SENTRY KEY
IMMOBILIZER MODULE
1. Turn the ignition on (transmission in park/
neutral).2. Use the DRB and select ``THEFT ALARM'',
``SKIM'' then ``MISCELLANEOUS''.
3. Select ``PROGRAM IGNITION KEYS''.
4. Enter secured access mode by entering the vehi-
cle four-digit PIN.
NOTE:A MAXIMUM OF EIGHT KEYS CAN BE
LEARNED TO EACH SKIM. ONCE A KEY IS
LEARNED TO A SKIM IT (THE KEY) CANNOT
BE RANFERRED TO ANOTHER VEHICLE.
If ignition key programming is unsuccessful, the
DRB will display one of the following messages:
Programming Not Attempted -The DRB at-
tempts to read the programmed key status and
there are no keys programmmed in the SKIM
memory.
Programming Key Failed -(Possible Used Key
From Wrong Vehicle) - SKIM is unable to program
key due to one of the following:
- faulty ignition key transponder
- ignition key is programmed to another vehicle.
8 Keys Already Learned, Programming Not
Done -SKIM transponder ID memory is full.
1. Obtain ignition keys to be programmed from
customer (8 keys maximum)
2. Using the DRB, erase all ignition keys by select-
ing ``MISCELLANEOUS'' and ``ERASE ALL
CURRENT IGN. KEYS''
3. Program all ignition keys.
Learned Key In Ignition -Ignition key tran-
sponder ID is currently programmed in SKIM mem-
ory.
3.3 DIAGNOSTIC TROUBLE CODES
Each diagnostic trouble code is diagnosed by
following a specific testing procedure. The diagnos-
tic test procedures contain step-by-step instructions
for determining the cause of trouble codes as well as
no trouble code problems. It is not necessary to
perform all of the tests in this book to diagnose an
individual code.
Always begin by reading the diagnostic trouble
codes using the DRBIIIt.
3.3.1 HARD CODE
A diagnostic trouble code that comes back within
one cycle of the ignition key is a ªhardº code. This
means that the defect is there every time the
powertrain control module checks that circuit or
function. Procedures in this manual verify if the
trouble code is a hard code at a the beginning of
each test. When it is not a hard code, an ªintermit-
tentº test must be performed.
Codes that are for Euro Stage III OBD monitors will
not set with just the ignition key on. Comparing these
7
GENERAL INFORMATION
ProCarManuals.com

4.3.3 ELECTRONIC PINION FACTOR
WARNING
The pinion factor must be set for all new trans-
mission control modules. If the pinion factor is not
set or if it is set incorrectly, any speed-related
accessories will not operate or will operate inaccu-
rately. This includes the speedometer, speed con-
trol, rolling door locks, and other devices that are
operated by the powertrain and body control mod-
ules. For instructions on setting the pinion factor,
see the appropriate transmission diagnostic man-
ual or the service manual.
5.0 RECOMMENDED TOOLS
AND EQUIPMENT
DRBIIIt(diagnostic readout box) scan tool
fuel pressure adapter (C-6631) or #6539
fuel pressure kit (C-4799-B) or #5069
fuel release hose (C-4799-1)
MinAir flow fitting #6457
jumper wires
ohmmeter
oscilloscope
vacuum gauge
voltmeter
12 volt test light minimum 25 ohms resistance
with probe #8382
CAUTION: A 12 VOLT TEST LIGHT SHOULD
NOT BE USED FOR THE FOLLOWING
CIRCUITS, DAMAGE TO THE POWERTRAIN
CONTROLLER WILL OCCUR.
²5 Volt Supply
²8 Volt Supply
²J1850 PCI Bus
²CCD Bus
²CKP Sensor Signal
²CMP Sensor Signal
²Vehicle Speed Sensor Signal
²O2 Sensor Signal
6.0 GLOSSARY OF TERMS
ABSantilock brake system
backfire,
popbackfuel ignites in either the intake or
the exhaust system
CKPcrank position sensor
CMPcamshaft position sensor
cuts out,
missesa steady pulsation or the inability of
the engine to maintain a consistent
rpmDLCdata link connector (previously
called ªengine diagnostic connectorº)
detona-
tion,
spark
knocka mild to severe ping, especially un-
der loaded engine conditions
ECTengine coolant temperature sensor
EGRexhaust gas recirculation valve and
system
genera-
torpreviously called ªalternatorº
hard
startThe engine takes longer than usual
to start, even though it is able to
crank normally.
hesita-
tion, sag,
stumble
There is a momentary lack of response
when the throttle is opened.
This can
occur at all vehicle speeds. If it is se-
vere enough, the engine may stall.
IATintake air temperature sensor
IACidle air control valve
JTECCombined engine and transmission
control module
lack of
power,
sluggish
The engine has less than expected
power, with little or no increase in vehi-
cle speed when the throttle is opened.
LDPLeak Detection Pump
MAPmanifold absolute pressure sensor
MILmalfunction indicator lamp
MTVmanifold tuning valve
O2Soxygen sensor
PCIProgrammable Communication In-
terface
PCMpowertrain control module
PCMpowertrain control module
PCVpositive crankcase ventilation
PEPPeripheral Expansion Port
poor fuel
economyThere is significantly less fuel mile-
age than other vehicles of the same
design and configuration
rough,
unstable,
or er-
ratic idle
stallingThe engine runs unevenly at idle
and causes the engine to shake if it
is severe enough. The engine idle
rpm may vary (called ªhuntingº).
This condition may cause stalling if
it is severe enough.
SKIMSentry Key Immobilizer Module
SKISSentry Key Immobilizer System
start and
stallThe engine starts but immediately
dies.
13
GENERAL INFORMATION
ProCarManuals.com

TEST ACTION APPLICABILITY
3 Turn off all accessories.
Start engine, allow engine to reach normal operating temperature.
Disconnect the Vacuum Supply Hose to the EGR Solenoid.
Connect a vacuum gauge to the disconnected hose.
Does the gauge read over 109of vacuum?All
Ye s®Go To 4
No®Repair the Vacuum Supply to the EGR Solenoid.
Perform VERIFICATION TEST VER-5A3.
4 Engine still running.
Reconnect the Vacuum Hose to the EGR Solenoid.
Disconnect the vacuum hose to the EGR Valve.
Connect a vacuum gauge to the disconnected hose.
Does the gauge pulsate?All
Ye s®Go To 5
No®Go To 7
5 While observing gauge, momentarily raise engine speed above 2000 rpm.
Did vacuum stabilize?All
Ye s®Go To 6
No®Replace EGR Valve Assembly.
Perform VERIFICATION TEST VER-5A3.
6 Remove the EGR Valve and inspect manifold and tube for restrictions.
Were any restrictions found?All
Ye s®Repair or replace as necessary.
Perform VERIFICATION TEST VER-5A3.
No®Replace EGR Valve Assembly.
Perform VERIFICATION TEST VER-5A3.
7 Check for sizeable exhaust leak.
Were any leaks found?All
Ye s®Repair as necessary.
Perform VERIFICATION TEST VER-5A3.
No®Go To 8
8 Engine Running.
Disconnect Back Pressure Hose from Transducer.
Connect a pressure gauge to the Back Pressure Hose.
Is pressure gauge pulsating?All
Ye s®Replace EGR Assembly.
Perform VERIFICATION TEST VER-5A3.
No®Go To 9
9 Check EGR Back Mount. Check Valve tightness. Check EGR Valve Gasket.
Were any problems found?All
Ye s®Repair or replace as necessary.
Perform VERIFICATION TEST VER-5A3.
No®Replace EGR Valve Assembly.
Perform VERIFICATION TEST VER-5A3.
132
DRIVEABILITY
P-0401 EGR SYSTEM FAILURE ÐContinued
ProCarManuals.com

Verification Tests
VERIFICATION TEST VER-1A APPLICABILITY
No Start Verification
Use this test to verify that a No Start condition has been repaired and that the vehicle can be
returned to the customer.
Note: If the Powertrain Control Module has been replaced and the correct VIN and
mileage have not been programmed, a DTC will be set in the ABS, Airbag and the
SKIM modules. In addition, if the vehicle is equipped with a Sentry Key Immobilizer
Module (SKIM), Secret Key data must be updated to enable starting. Refer to
GENERAL INFORMATION section for programming information for the PCM, SKIM
and the Transponder (ignition key).
1. Inspect the vehicle to ensure that all components related to the repair are connected
properly.
2. Inspect the engine oil for fuel contamination. Replace the oil and filter as necessary
3. Attempt to start the engine.
4. If the No Start condition is still present, refer to the symptom list and perform diagnostic
testing as necessary. Refer to any Technical Service Bulletins that may apply.
5. Run the engine for one warm-up cycle to verify proper operation. With the DRBIIIt, confirm
that no DTC's are present and that all components are functioning properly.
6. If DTC's are present, refer to the symptom list and perform diagnostic testing as necessary.ALL
VERIFICATION TEST VER-2A APPLICABILITY
Non-OBDII Verification
Use this test to verify that a non-OBDII symptom has been repaired and that the vehicle can
be returned to the customer. A non-OBDII symptom is a comprehensive component related
symptom that is not the result of a failed OBDII major monitor.
Note: If the Powertrain Control Module has been replaced and the correct VIN and
mileage have not been programmed, a DTC will be set in the ABS, Airbag and the
SKIM modules. In addition, if the vehicle is equipped with a Sentry Key Immobilizer
Module (SKIM), Secret Key data must be updated to enable starting. Refer to
GENERAL INFORMATION section for programming information for the PCM, SKIM
and the Transponder (ignition key).
1. Inspect the vehicle to ensure that all components related to the repair are connected
properly.
2. With the DRBIIIt, Clear DTC's and Reset Memory (all engine values).
3. Run the engine for one warm-up cycle to verify proper operation.
4. Road test the vehicle. Use all accessories that may be related to this repair.
With the DRBIIIt, confirm that no DTC's are present and that all components are functioning
properly.
6. If this test is being performed after a No Trouble Code test, verify that the symptom is no
longer present. If the symptom is still present, or any other symptom or DTC is present, refer
to the symptom list for further diagnostic testing procedures. Check for any Technical Service
Bulletins that may apply.
7. If there are no DTC's present and all components are functioning properly, repair is
complete.ALL
317
VERIFICATION TESTS
ProCarManuals.com