brakes CHRYSLER VOYAGER 2000 Diagnostic Manual

Symptom:
P-0500 NO VEHICLE SPEED SENSOR SIGNAL
When Monitored and Set Condition:
P-0500 NO VEHICLE SPEED SENSOR SIGNAL
When Monitored: For 3 Speed: With engine running, transmission not in park or neutral,
brakes not applied, engine rpm greater than 1500. For 4 Speed: With the engine running,
transmission not in park or neutral, brakes not applied, engine rpm greater than 1500.
Set Condition: For 3 Speed: No signal from the vehicle speed sensor for more than 11
seconds for 2 consecutive trips. For 4 Speed: No signal from the vehicle speed sensor (TCM)
is present for more than 11 seconds for 2 consecutive trips.
POSSIBLE CAUSES
ELECTRONIC AUTO TRANSAXLE TROUBLE CODES PRESENT
8-VOLT SUPPLY CIRCUIT OPEN
PCM DEF (NO VSS SIGNAL CKT)
PCM TERMINAL DEFECTIVE
VEHICLE SPEED SENSOR GROUND CIRCUIT OPEN
VEHICLE SPEED SENSOR SIGNAL CIRCUIT WIRING HARNESS OBSERVABLE DEFECT
PINION GEAR DEFECTIVE
OUTPUT SPEED SENSOR CIRCUIT OPEN
OUTPUT SPEED SENSOR CIRCUIT SHORTED TO GROUND
VEHICLE SPEED SENSOR SIGNAL CIRCUIT OPEN
VSS SIGNAL CIRCUIT SHORTED TO GROUND
OUTPUT SPEED SENSOR DEFECTIVE
OUTPUT SPEED SENSOR DEFECTIVE (RES > 5.0)
PCM DEFECTIVE (NO VSS SIGNAL CKT)
PCM DEFECTIVE (NO VSS SIGNAL CKT)
TCM DEFECTIVE (VSS SIG CKT)
VSS DEFECTIVE
153
DRIVEABILITY
ProCarManuals.com

Symptom:
P-1698 NO CCD MESSAGES FROM TCM
When Monitored and Set Condition:
P-1698 NO CCD MESSAGES FROM TCM
When Monitored: With the engine running.
Set Condition: No CCD messages are received from the TCM for 10 seconds.
POSSIBLE CAUSES
DRB DOES NOT SHOW BUS OPERATIONAL
CCD WIRING HARNESS OBSERVABLE DEFECT
CCD BUS (+) CIRCUIT OPEN BETWEEN PCM AND TCM
CCD BUS (-) CIRCUIT OPEN BETWEEN PCM AND TCM
PCM DEFECTIVE (NO CCD MESSAGE)
TCM DEFECTIVE (NO CCD MESSAGE)
TEST ACTION APPLICABILITY
1 Ignition On
With the DRB, select9Transmission9.
Note: The CCD Bus test is automatic.
Does the DRB show9Bus Operational9?All
Ye s®Go To 2
No®Go to the appropriate symptom group for body diagnostics.
2 Ignition Off
With the DRB, select9Engine9module.
With the DRB erase trouble codes.
Raise all four wheels off the ground and properly support the vehicle.
Caution: Keep clear of rotating wheels in the next step.
Start the engine. Place the Shift Lever in Drive and allow the wheels to rotate for 1
minute.
Step on the brakes, put the Shift Lever back in Park.
With the DRB read Trouble Codes.
Does display show9No CCD Message from TCM9and the start run counter equal to
zero?All
Ye s®Go To 3
No®Go To 7
224
DRIVEABILITY
ProCarManuals.com

Symptom:
* CHECKING FUEL DELIVERY
POSSIBLE CAUSES
FUEL LINE RESTRICTED
FUEL FILTER DEFECTIVE
FUEL LINE RESTRICTED
FUEL PRESSURE REGULATOR DEFECTIVE
FUEL PUMP/REGULATOR ASSEMBLY DEFECTIVE
FUEL RETURN LINE DEFECTIVE
FUEL PUMP/REGULATOR ASSEMBLY DEFECTIVE
TEST ACTION APPLICABILITY
1 Ignition Off
Warning: The Fuel System must be opened and may be under high pressure.
Release the Fuel Pressure.
Connect a Fuel Pressure Gauge to test port.
Ignition On, Engine Not Running
With the DRB, actuate Fuel System. Fuel Pressure should be 43 to 53 psi.
Fuel Pressure should be 43 to 53 psi.
Is the Fuel Pressure within the specification?ENGINE - 2.4L I-4
DOHC and/or EN-
GINE - 3.3L V6
and/or ENGINE -
3.3L V6 FFV and/or
ENGINE - 3.8L V6
Ye s®Go To 2
No®Go To 5
2 Ignition Off
Note: Make sure the Gear Lever is in neutral, and the Park Brakes engaged.
Start the engine.
Monitor the Fuel Pressure Gauge in the next step.
While monitoring the pressure, momentarily snap Throttle wide open raising RPM to
above 3000.
Did the fuel pressure drop below 35 psi at all?All
Ye s®Go To 3
No®Test Complete.
3 Ignition Off
Inspect the Chassis Fuel Supply Line to the engine for a kink or restriction.
Is the line kinked or restricted?All
Ye s®Release the fuel pressure. Repair the Fuel Line as necessary.
Perform Powertrain Verification Test VER-2A.
No®Go To 4
237
DRIVEABILITY
ProCarManuals.com

TEST ACTION APPLICABILITY
8 Ignition Off
Inspect the Chassis Fuel Supply Line to engine for a kink or restriction.
Is the Line kinked or restricted?ENGINE - 2.4L I-4
DOHC and/or EN-
GINE - 3.3L V6
and/or ENGINE -
3.3L V6 FFV and/or
ENGINE - 3.8L V6
Ye s®Release the Fuel Pressure. Repair the Fuel Line as necessary.
Perform Powertrain Verification Test VER-2A.
No®Go To 9
9 Ignition Off
Warning: The Fuel System must be opened and may be under high pressure.
Release the fuel pressure.
Connect a Fuel Pressure Adapter and Gauge to Supply Line between Tank/Filter.
Turn ignition on.
With the DRB, actuate the Fuel System test.
Is the Fuel Pressure at least 5 psi higher than previously recorded pressure?ENGINE - 2.4L I-4
DOHC and/or EN-
GINE - 3.3L V6
and/or ENGINE -
3.3L V6 FFV and/or
ENGINE - 3.8L V6
Ye s®Release the Fuel Pressure. Replace the Fuel Filter.
Perform Powertrain Verification Test VER-2A.
No®Go To 10
10 Ignition Off
Warning: The Fuel System must be opened and may be under high pressure.
Release the fuel pressure.
Connect a Fuel Pressure Adapter and Gauge to Supply Line between Tank/Filter.
Turn ignition on.
With the DRB, actuate the Fuel System test.
Is Fuel Pressure at least 5 psi higher than previously recorded pressure?ENGINE - 2.4L I-4
DOHC and/or EN-
GINE - 3.3L V6
and/or ENGINE -
3.3L V6 FFV and/or
ENGINE - 3.8L V6
Ye s®Test Complete.
No®Release the Fuel Pressure. Replace the Fuel Pump and Regulator
Assembly.
Perform Powertrain Verification Test VER-2A.
11 Ignition Off
Warning: The Fuel System must be opened and may be under high pressure.
Relieve the Fuel Pressure.
Tee-in Fuel Pressure Gauge into the Fuel Supply Hose using Tool #6433.
Turn ignition on.
With the DRB, actuate the ASD Fuel System test.
Is the Fuel Pressure between 43 and 53 psi?ENGINE - 3.0L V6
Ye s®Go To 12
No®Go To 15
12 Ignition Off
Note: Make sure the Gear Lever is in neutral, and the Park Brakes engaged.
Start the engine.
Monitor the Fuel Pressure Gauge in the next step.
While monitoring the pressure, momentarily snap Throttle wide open raising RPM to
above 3000.
Did the fuel pressure drop below 35 psi at all?All
Ye s®Go To 13
No®Test Complete.
239
DRIVEABILITY
* CHECKING FUEL DELIVERY ÐContinued
ProCarManuals.com

Symptom:
SPEED CONTROL DENIED MESSAGE
TEST ACTION APPLICABILITY
1 At this time the S/C switch and servo functions appear to operate properly.
Using the DRB, monitor the speed control9cutout9status.
Road test the vehicle at speeds over 30mph and attempt to set the speed control.
The following items will not allow the speed control to set. The last or most recent
cause for speed control not to set is indicated by the9Denied9status.
If ON/OFF Denied message is indicated, the Powertrain Control Module does not see
an9ON9signal from the switch at cavity 41.
If SPEED Denied message is indicated, the vehicle speed as seen by the Powertrain
Control Module at cavity 66 is not greater than 36 mph.
If RPM Denied message is indicated, the engine rpm is excessively high.
If BRAKE Denied message is indicated, the Brake Switch Sense Circuit is open
indicating to the PCM that the Brakes are applied. The Sense Circuit, cavity 62 of the
PCM, is grounded through the Brake Pedal Switch when the Brakes are released.
If P/N Denied message is indicated, Park/Neutral Switch Sense Circuit is grounded
indicating to PCM that transmission is not in gear. The Sense Circuit, cavity 76 of
PCM, is grounded through the Park/Neutral Switch when transmission is in park or
neutral.
If RPM/SPD Denied message is indicated, the PCM senses excessive engine rpm for
a given vehicle speed.
If SOL FLT Denied message is indicated, the Powertrain Control Module senses a
Servo Solenoid Circuit trouble code that is maturing or set in memory.All
Test Complete.
263
SPEED CONTROL
ProCarManuals.com