fuel cap release CHRYSLER VOYAGER 2000 Diagnostic Manual

TEST ACTION APPLICABILITY
7 Turn ignition off.
Warning: The fuel system is under a constant pressure (even with the engine
off). Before testing or servicing any fuel system hose, fitting or line, the fuel
system pressure must be released.
Remove the pressure test port cap at the fuel rail test port. Connect a fuel pressure
gauge to the test port pressure fitting on the fuel rail.
Ignition on. With the DRB, actuate the ASD Fuel System test and observe the fuel
pressure gauge.
Note: Fuel pressure specification is 49.2 psi +/- 5 psi
Choose a conclusion that best matches your fuel pressure reading.All
Below Specification
Go To 8
Within Specification
Go To 11
Above Specification
Replace the fuel filter pressure regulator.
Caution: Stop ALL Actuations.
8 Turn ignition off.
Warning: The fuel system is under a constant pressure (even with the engine
off). Before testing or servicing any fuel system hose, fitting or line, the fuel
system pressure must be released.
Raise vehicle on hoist,and disconnect the fuel pressure line at the fuel pump module.
Install speial 5/169fuel line adapter tool #6539 between disconnected fuel line and
the fuel pump module.
Attach a fuel pressure test gauge to the88T'' fitting on tool #6539.
Ignition on. With the DRB, actuate the ASD Fuel System test and observe the fuel
pressure gauge.
Note: Fuel pressure specification is 49.2 psi +/- 5 psi.
Is the fuel pressure within specification now?ALL
Ye s®Repair the restriction in the chassis fuel supply line between the
fuel tank and fuel rail.
No®Go to 9
Caution: Stop ALL Actuations.
9Warning: The fuel system is under a constant pressure (even with the engine
off). Before testing or servicing any fuel system hose, fitting or line, the fuel
system pressure must be released.
Remove the Fuel Pump Module and inspect the Fuel Inlet Strainer.
Is the Fuel Inlet Strainer plugged?All
Ye s®Replace the Fuel Inlet Strainer.
No®Go To 10
10 If there are no potential causes remaining, the Fuel Pump Module is assumed to be
defective.
View repair options.All
Repair
Replace the Fuel Pump Module
77
DRIVEABILITY
P-0171±1/1 FUEL SYSTEM LEAN ÐContinued
ProCarManuals.com

TEST ACTION APPLICABILITY
11 Check for any of the following conditions/mechanical problems.
ENGINE VACUUM Ð must be at least 13 inches in neutral
ENGINE VALVE TIMING Ð must be within specifications
ENGINE COMPRESSION Ð must be within specifications
ENGINE EXHAUST SYSTEM Ð must be free of any restrictions or leaks
ENGINE PVC SYSTEM Ð must flow freely
TORQUE CONVERTER STALL SPEED Ð must be within specifications
POWER BRAKE BOOSTER Ð no internal vacuum leaks
FUEL- must be free of contamination
FUEL INJECTOR Ð plugged or restricted injector; control wire not connected to
correct injector.
Are there any engine mechanical problems?All
Ye s®Repair as necessary.
Perform FUEL SYSTEM/MISFIRE MONITOR VERIFICATION
TEST
No®Go To 12
12 Turn ignition off.
Warning: The fuel system is under constant pressure (even with the engine
off). Before testing or servicing any fuel system hose, fitting or line, the fuel
system pressure must be released.
Disconnect the fuel supply line at the fuel rail.
Connect fuel line adapter #6539(5/169) or #6631 (3/89) to the disconnected fuel supply
line. Insert the other end of the adapter into a graduated container.
Caution: Do not operate the fuel pump for more than 7 seconds in the next
step. Fuel pump module reservoir may run empty and damage to the fuel
pump may result.
Specification: A good fuel pump will deliver at least 1/4 liter of fuel in 7
seconds.
With the DRB, actuate the ASD Fuel System test for 7 seconds.
Is the fuel pump capacity within specification?All
Ye s®Test Complete.
No®Check for a kinked/damaged fuel supply line between the fuel
tank and fuel rail. If OK, replace the fuel filter/pressure regulator.
Caution: Stop ALL Actuations.
13 The conditions required to set the DTC are no longer present.
With the DRB read and record the freeze frame data and the ªFuel System Similar
Conditions Windowº data.
Utilize the data and try to duplicate the operating conditions at which the DTC was
set. Pay particular attention to the ECT and RPM for added diagnostics.
Note: Refer to any TSB's that may apply to the symptom.
Test Complete
Repair
Test Complete.
78
DRIVEABILITY
P-0171±1/1 FUEL SYSTEM LEAN ÐContinued
ProCarManuals.com

TEST ACTION APPLICABILITY
8 Turn ignition off.
Warning: The fuel system is under a constant pressure (even with the engine
off). Before testing or servicing any fuel system hose, fitting or line, the fuel
system pressure must be released.
Remove the pressure test port cap at the fuel rail test port. Connect a fuel pressure
gauge to the test port pressure fitting on the fuel rail.
Ignition on. With the DRB, actuate the ASD Fuel System test and observe the fuel
pressure gauge.
Note: Fuel pressure specification is 49.2 psi +/þ 5 psi.
Choose a conclusion that best matches your fuel pressure reading.All
Below Specification
Go To 9
Within Specification
Go To 13
Above Specification
Replace the fuel filter/pressure regulator.
Caution: Stop ALL Actuations.
9 Check for any of the following conditions/mechanical problems.
ENGINE VACUUM Ð must be at least 13 inches in neutral
ENGINE VALVE TIMING Ð must be within specifications
ENGINE COMPRESSION Ð must be within specifications
ENGINE EXHAUST SYSTEM Ð must be free of any restrictions or leaks.
ENGINE PVC SYSTEM Ð must flow freely
TORQUE CONVERTER STALL SPEED Ð must be within specifications
POWER BRAKE BOOSTER Ð no internal vacuum leaks
FUEL - must be free of contamination
FUEL INJECTOR Ð plugged or restricted injector; control wire not connected to
correct injector
Are there any engine mechanical problems?All
Ye s®Repair as necessary.
Perform FUEL SYSTEM/MISFIRE MONITOR VERIFICATION
TEST
No®Go To 10
10 Turn ignition off.
Warning: The fuel system is under a constant pressure (even with the engine
off). Before testing or servicing any fuel system hose, fitting or line, the fuel
system pressure must be released.
Raise vehicle on hoist, and disconnect the fuel pressure line at the fuel pump module.
Install special 5/169fuel line adapter tool #6539 between disconnected fuel line and
the fuel pump module.
Attach a fuel pressure test gauge to the ªT'' fitting on tool #6539.
Ignition on. With the DRB, actuate the ASD Fuel System test and observe the fuel
pressure gauge.
Note: Fuel pressure specification is 49.2 psi +/- 5 psi.
Is the fuel pressure within specification now?All
Ye s®Repair the restriction in the chassis fuel supply line between the
fuel tank and fuel rail.
No®Go to 11
Caution: Stop ALL Actuations.
81
P0172 -1/1 FUEL SYSTEM RICH ÐContinued
ProCarManuals.com