battery CHRYSLER VOYAGER 2001 Repair Manual

TEST ACTION APPLICABILITY
2WARNING: TURN IGNITION OFF, DISCONNECT THE BATTERY AND WAIT
TWO MINUTES BEFORE PROCEEDING.
WARNING: DO NOT PLACE AN INTACT UNDEPLOYED SEAT BACK PAD-
DED SIDE DOWN ON A HARD SURFACE, THE AIRBAG WILL PROPEL
INTO THE AIR IF ACCIDENTALLY DEPLOYED, AND COULD RESULT IN
SERIOUS OR FATAL INJURY.
Disconnect the Left Seat Airbag inline connector located between the seat back and
seat cushion.
Do not disconnect the airbag connectors at the base of the seat.
Disconnect the Left Side Impact Airbag Control Module connector
NOTE: Check connectors - Clean and repair as necessary.
Connect the SRS Load Tool 8443 SIACM adaptor to the Left Side Impact Airbag
Control Module connector.
Measure the resistance of the Left Seat Squib Line 2 circuit between the Left Side
Impact Airbag Control Module connector and ground.
Is the resistance below 5.0 Ohms on the Left Seat Squib Line 2 circuit?All
Ye s®Repair Left Seat Squib Line 2 short to ground.
Perform AIRBAG VERIFICATION TEST - VER 1.
No®Go To 3
NOTE: When reconnecting Airbag system components, the ignition must be
turned off and the battery must be disconnected.
3WARNING: TURN IGNITION OFF, DISCONNECT THE BATTERY AND WAIT
TWO MINUTES BEFORE PROCEEDING.
WARNING: DO NOT PLACE AN INTACT UNDEPLOYED SEAT BACK PAD-
DED SIDE DOWN ON A HARD SURFACE, THE AIRBAG WILL PROPEL
INTO THE AIR IF ACCIDENTALLY DEPLOYED, AND COULD RESULT IN
SERIOUS OR FATAL INJURY.
Disconnect the Left Seat Airbag inline connector located between the seat back and
seat cushion.
Do not disconnect the airbag connectors at the base of the seat.
Disconnect the Left Side Impact Airbag Control Module connector.
NOTE: Check connectors - Clean and repair as necessary.
Connect the SRS Load Tool 8443 SIACM adaptor to the Left Side Impact Airbag
Control Module connector.
Measure the resistance of the Left Seat Squib Line 1 circuit between the Left SIACM
connector and ground.
Is the resistance below 5.0 Ohms on the Left Seat Squib Line 1 circuit?All
Ye s®Repair Left Seat Squib Line 1 short to ground.
Perform AIRBAG VERIFICATION TEST - VER 1.
No®Go To 4
NOTE: When reconnecting Airbag system components, the ignition must be
turned off and the battery must be disconnected.
68
AIRBAG
LEFT SIACM, SEAT SQUIB SHORT TO GROUND - ACTIVE ÐContinued

TEST ACTION APPLICABILITY
4WARNING: TURN IGNITION OFF, DISCONNECT THE BATTERY AND WAIT
TWO MINUTES BEFORE PROCEEDING.
WARNING: IF THE LEFT SIDE IMPACT AIRBAG CONTROL MODULE IS
DROPPED AT ANY TIME, IT MUST BE REPLACED.
If there are no possible causes remaining, view repair.All
Repair
Replace the Left Side Impact Airbag Control Module in accordance
with Service Instructions. WARNING: make sure the battery is
disconnected and wait 2 minutes before proceeding.
Perform AIRBAG VERIFICATION TEST - VER 1.
NOTE: When reconnecting Airbag system components, the ignition must be
turned off and the battery must be disconnected.
69
AIRBAG
LEFT SIACM, SEAT SQUIB SHORT TO GROUND - ACTIVE ÐContinued

ORC, NO PCI TRANSMISSION - ACTIVE
When Monitored: With the ignition in the On position and the ORC transmitting
information on the PCI BUS.
Set Condition: The code will set if the ORC cannot detect the ORC transmitting
information on the PCI BUS for 5 consecutive seconds. NOTE: Any PCI Bus Failure will
cause this code to set.
POSSIBLE CAUSES
ORC, ACTIVE OR STORED CODE
TEST ACTION APPLICABILITY
1WARNING: TURN THE IGNITION OFF, DISCONNECT THE BATTERY AND
WAIT TWO MINUTES BEFORE PROCEEDING.
WARNING: IF THE AIRBAG MODULE IS DROPPED AT ANY TIME, IT MUST
BE REPLACED.
If there are no possible causes remaining, view repair.All
Repair
Replace the Occupant Restraint Controller in accordance with
Service Instructions. WARNING: make sure the battery is discon-
nected and wait 2 minutes before proceeding.
Perform AIRBAG VERIFICATION TEST - VER 1.
NOTE: When reconnecting airbag system components the Ignition must be
turned off and the Battery must be disconnected.
72
AIRBAG
ORC ACCELEROMETER - ACTIVE ÐContinued

TEST ACTION APPLICABILITY
3WARNING: TURN THE IGNITION OFF, DISCONNECT THE BATTERY AND
WAIT TWO MINUTES BEFORE PROCEEDING.
WARNING: IF THE OCCUPANT RESTRAINT CONTROLLER IS DROPPED
AT ANY TIME, IT MUST BE REPLACED.
If there are no possible causes remaining, view repair.All
Repair
Replace the Occupant Restraint Controller in accordance with
Service Instructions. WARNING: make sure the battery is discon-
nected and wait 2 minutes before proceeding.
Perform AIRBAG VERIFICATION TEST - VER 1.
NOTE: When reconnecting airbag system components the Ignition must be
turned off and the Battery must be disconnected.
74
AIRBAG
ORC, CALIBRATION MISMATCH - ACTIVE ÐContinued

Symptom List:
ORC, CALIBRATION MISMATCH - STORED
ORC, CLUSTER MESSAGE MISMATCH - STORED
ORC, DRIVER SBS OPEN - STORED
ORC, DRIVER SBS SHORT TO BATTERY - STORED
ORC, DRIVER SBS SHORT TO GROUND - STORED
ORC, DRIVER SBT CIRCUIT OPEN - STORED
ORC, DRIVER SBT CIRCUIT SHORT - STORED
ORC, DRIVER SBT SHORT TO BATTERY - STORED
ORC, DRIVER SBT SHORT TO GROUND - STORED
ORC, DRIVER SQUIB 1 CIRCUIT OPEN - STORED
ORC, DRIVER SQUIB 1 CIRCUIT SHORT - STORED
ORC, DRIVER SQUIB 1 SHORT TO BATTERY - STORED
ORC, DRIVER SQUIB 1 SHORT TO GROUND - STORED
ORC, DRIVER SQUIB 2 CIRCUIT OPEN - STORED
ORC, DRIVER SQUIB 2 CIRCUIT SHORT - STORED
ORC, DRIVER SQUIB 2 SHORT TO BATTERY - STORED
ORC, DRIVER SQUIB 2 SHORT TO GROUND - STORED
ORC, LOSS OF IGNITION RUN ONLY - STORED
ORC, LOSS OF IGNITION RUN-START - STORED
ORC, NO CLUSTER MESSAGE - STORED
ORC, NO ODOMETER MESSAGE - STORED
ORC, PASSENGER SBS OPEN - STORED
ORC, PASSENGER SBS SHORT TO BATTERY - STORED
ORC, PASSENGER SBS SHORT TO GROUND - STORED
ORC, PASSENGER SBT CIRCUIT OPEN - STORED
ORC, PASSENGER SBT CIRCUIT SHORT - STORED
ORC, PASSENGER SBT SHORT TO BATTERY - STORED
ORC, PASSENGER SBT SHORT TO GROUND - STORED
ORC, PASSENGER SQUIB 1 CIRCUIT OPEN - STORED
ORC, PASSENGER SQUIB 1 CIRCUIT SHORT - STORED
ORC, PASSENGER SQUIB 1 SHORT TO BATTERY - STORED
ORC, PASSENGER SQUIB 1 SHORT TO GROUND - STORED
ORC, PASSENGER SQUIB 2 CIRCUIT OPEN - STORED
ORC, PASSENGER SQUIB 2 CIRCUIT SHORT - STORED
ORC, PASSENGER SQUIB 2 SHORT TO BATTERY - STORED
ORC, PASSENGER SQUIB 2 SHORT TO GROUND - STORED
ORC, VEHICLE BODY STYLE UNKNOWN - STORED
ORC, WARNING INDICATOR CIRCUIT OPEN - STORED
ORC, WARNING INDICATOR CIRCUIT SHORT - STORED
Test Note: All symptoms listed above are diagnosed using the same tests.
The title for the tests will be ORC, CALIBRATION MISMATCH
- STORED.
75
AIRBAG

When Monitored and Set Condition:
ORC, CALIBRATION MISMATCH - STORED
When Monitored: With ignition on, the ORC monitors the PCI Bus for the VIN message
containing the body style. The PCM transmits the 17- character VIN message every 14
seconds. Note: The VIN message should match the vehicle VIN plate.
Set Condition: If the Body style stored in ORC does not exactly match the vehicle body
style indicated by the PCM, then the fault shall be set.
ORC, CLUSTER MESSAGE MISMATCH - STORED
When Monitored: After the MIC bulb test is completed, the ORC compares the Lamp
Request by ORC (On or Off) and the Lamp on by MIC (On or Off) PCI Bus messages. Each
message is transmitted one time per second or when a change in the lamp state occur.
Set Condition: If the Lamp Request by ORC (On or Off) and the Lamp on by MIC (On or
Off) messages do not match, the code will set.
ORC, DRIVER SBS OPEN - STORED
When Monitored: The ORC monitors the Seat Belt Switch circuit for an open condition.
Set Condition: The code will set if the ORC does not detect the correct circuit voltage.
ORC, DRIVER SBS SHORT TO BATTERY - STORED
When Monitored: The ORC monitors the Seat Belt Switch circuit for an short to battery.
Set Condition: The code will set if the ORC detects high circuit voltage.
ORC, DRIVER SBS SHORT TO GROUND - STORED
When Monitored: The ORC monitors the Seat Belt Switch circuit for a shorted together
or shorted to ground condition.
Set Condition: The code will set if the ORC detects low circuit voltage.
ORC, DRIVER SBT CIRCUIT OPEN - STORED
When Monitored: When the ignition is On, the ORC monitors the resistance of the Driver
Seat Belt Tensioner circuits.
Set Condition: The ORC has detected an open circuit or high resistance on the Driver
Seat Belt Tensioner circuits.
ORC, DRIVER SBT CIRCUIT SHORT - STORED
When Monitored: When the ignition is on, the ORC monitors the resistance of the Driver
Seat Belt Tensioner circuits.
Set Condition: The ORC has detected low resistance in the Driver Seat Belt Tensioner
circuits.
76
AIRBAG
ORC, CALIBRATION MISMATCH - STORED ÐContinued

ORC, DRIVER SBT SHORT TO BATTERY - STORED
When Monitored: When the ignition is on, the ORC monitors the voltage of the Driver
Seat Belt Tensioner circuits.
Set Condition: When the ignition is on, the ORC monitors the voltage of the Driver Seat
Belt Tensioner circuits.
ORC, DRIVER SBT SHORT TO GROUND - STORED
When Monitored: When the ignition is on, the ORC monitors the resistance of the Driver
Seat Belt Tensioner circuits for low resistance.
Set Condition: The ORC has detected a short to ground in the Driver Seat Belt Tensioner
circuits.
ORC, DRIVER SQUIB 1 CIRCUIT OPEN - STORED
When Monitored: When the ignition is on, the ORC monitors the resistance of the Driver
Squib 1 circuits.
Set Condition: The ORC has detected an open circuit or high resistance in the Driver
Squib 1 circuits.
ORC, DRIVER SQUIB 1 CIRCUIT SHORT - STORED
When Monitored: When the ignition is on, the ORC monitors the resistance of the Driver
Squib 1 circuits.
Set Condition: The ORC has detected low resistance on the Driver Squib 1 circuits.
ORC, DRIVER SQUIB 1 SHORT TO BATTERY - STORED
When Monitored: When the ignition is on, the ORC monitors the voltage of the Driver
Squib 1 circuits.
Set Condition: The ORC has detected high voltage on the Driver Squib 1 circuits.
ORC, DRIVER SQUIB 1 SHORT TO GROUND - STORED
When Monitored: When the ignition is on, the ORC monitors the resistance of the Driver
Squib 1 circuits.
Set Condition: The ORC has detected a short to ground in the Driver Squib 1 circuits.
ORC, DRIVER SQUIB 2 CIRCUIT OPEN - STORED
When Monitored: When the ignition is on, the ORC monitors the resistance of the Driver
Squib 2 circuits.
Set Condition: The ORC has detected an open circuit or high resistance in the Driver
Squib 2 circuits.
ORC, DRIVER SQUIB 2 CIRCUIT SHORT - STORED
When Monitored: When the ignition is on, the ORC monitors the resistance of the Driver
Squib 2 circuits.
Set Condition: The ORC has detected low resistance on the Driver Squib 2 circuits.
77
AIRBAG
ORC, CALIBRATION MISMATCH - STORED ÐContinued

ORC, DRIVER SQUIB 2 SHORT TO BATTERY - STORED
When Monitored: When the ignition is on, the ORC monitors the voltage of the Driver
Squib 2 circuits.
Set Condition: The ORC has detected high voltage on the Driver Squib 2 circuits.
ORC, DRIVER SQUIB 2 SHORT TO GROUND - STORED
When Monitored: When the ignition is on, the ORC monitors the resistance of the Driver
Squib 2 circuits.
Set Condition: The ORC has detected a short to ground in the Driver Squib 2 circuits.
ORC, LOSS OF IGNITION RUN ONLY - STORED
When Monitored: With the ignition in the run position the ORC monitors the ORC Run
Only Driver circuit for proper system voltage.
Set Condition: If the voltage on the ORC Run Only Driver circuit drops below 4.5 volts,
the code will set.
ORC, LOSS OF IGNITION RUN-START - STORED
When Monitored: With the ignition in the run or start position the ORC monitors the
ORC Run-Start Driver circuit for proper system voltage.
Set Condition: If the voltage on the ORC Run-Start Driver circuit drops below 4.5 volts,
the code will set.
ORC, NO CLUSTER MESSAGE - STORED
When Monitored: With the ignition in the ON position, the ORC monitors the PCI Bus for
a message from the MIC containing the airbag warning lamp status. The MIC transmits
the message one time at ignition on, lamp state change, or in response to the ORC lamp
message.
Set Condition: If the MIC message is not received for 10 consecutive seconds, the code
will set.
ORC, NO ODOMETER MESSAGE - STORED
When Monitored: With ignition on, the ORC monitors the PCI Bus for the Odometer
message from the Body Control Module. The BCM transmits the odometer message at 1
second intervals.
Set Condition: The code will set, if the ORC does not see the odometer message for 10
seconds.
ORC, PASSENGER SBS OPEN - STORED
When Monitored: The ORC monitors the Seat Belt Switch circuit for an open condition.
Set Condition: The code will set if the ORC does not detect the correct circuit voltage.
78
AIRBAG
ORC, CALIBRATION MISMATCH - STORED ÐContinued

ORC, PASSENGER SBS SHORT TO BATTERY - STORED
When Monitored: The ORC monitors the Seat Belt Switch circuit for an short to battery.
Set Condition: The code will set if the ORC detects high circuit voltage.
ORC, PASSENGER SBS SHORT TO GROUND - STORED
When Monitored: The ORC monitors the Seat Belt Switch circuit for a shorted together
or shorted to ground condition.
Set Condition: The code will set if the ORC detects low circuit voltage.
ORC, PASSENGER SBT CIRCUIT OPEN - STORED
When Monitored: When the ignition is on, the ORC monitors the resistance of the
Passenger Seat Belt Tensioner circuits.
Set Condition: The ORC has detected an open circuit or high resistance or open circuit in
the Passenger Seat Belt Tensioner circuits.
ORC, PASSENGER SBT CIRCUIT SHORT - STORED
When Monitored: When the ignition is on, the ORC monitors the resistance of the
Passenger Seat Belt Tensioner circuits.
Set Condition: The ORC has detected low resistance in the Passenger Seat Belt Tensioner
circuits.
ORC, PASSENGER SBT SHORT TO BATTERY - STORED
When Monitored: When the ignition is on, the ORC monitors the voltage of the Passenger
Seat Belt Tensioner circuits.
Set Condition: The ORC has detected high voltage on the Passenger Seat Belt Tensioner
circuits.
ORC, PASSENGER SBT SHORT TO GROUND - STORED
When Monitored: When the ignition is on, the ORC monitors the resistance of the
Passenger Seat Belt Tensioner circuits for low resistance.
Set Condition: The ORC has detected a short to ground in the Passenger Seat Belt
Tensioner circuits.
ORC, PASSENGER SQUIB 1 CIRCUIT OPEN - STORED
When Monitored: With the ignition is On, the ORC monitors the resistance of the
Passenger Squib 1 circuits.
Set Condition: The ORC has detected an open circuit or high resistance on the Driver
Squib 1 circuits.
ORC, PASSENGER SQUIB 1 CIRCUIT SHORT - STORED
When Monitored: When the ignition is on, the ORC monitors the resistance of the
Passenger Squib 1 circuits.
Set Condition: The ORC has detected low resistance in the Passenger Squib 1 circuits.
79
AIRBAG
ORC, CALIBRATION MISMATCH - STORED ÐContinued

ORC, PASSENGER SQUIB 1 SHORT TO BATTERY - STORED
When Monitored: When the ignition is on, the ORC monitors the voltage of the Passenger
Squib 1 circuits.
Set Condition: The ORC has detected high voltage on the Passenger Squib 1 circuits.
ORC, PASSENGER SQUIB 1 SHORT TO GROUND - STORED
When Monitored: When the ignition is on, the ORC monitors the resistance of the
Passenger Squib 1 circuits for low resistance.
Set Condition: The ORC has detected a short to ground in the Passenger Squib 1 circuits.
ORC, PASSENGER SQUIB 2 CIRCUIT OPEN - STORED
When Monitored: With the ignition is On, the ORC monitors the resistance of the
Passenger Squib 2 circuits.
Set Condition: The ORC has detected an open circuit or high resistance on the Passenger
Squib 2 circuits.
ORC, PASSENGER SQUIB 2 CIRCUIT SHORT - STORED
When Monitored: When the ignition is on, the ORC monitors the resistance of the
Passenger Squib 2 circuits.
Set Condition: The ORC has detected low resistance in the Passenger Squib 2 circuits.
ORC, PASSENGER SQUIB 2 SHORT TO BATTERY - STORED
When Monitored: When the ignition is on, the ORC monitors the voltage of the Passenger
Squib 2 circuits.
Set Condition: The ORC has detected high voltage on the Passenger Squib 2 circuits.
ORC, PASSENGER SQUIB 2 SHORT TO GROUND - STORED
When Monitored: When the ignition is on, the ORC monitors the resistance of the
Passenger Squib 2 circuits for low resistance.
Set Condition: The ORC has detected a short to ground in the Passenger Squib 2 circuits.
ORC, VEHICLE BODY STYLE UNKNOWN - STORED
When Monitored: With ignition on, the ORC monitors the PCI Bus for the VIN message
containing the vehicle body style from the Powertrain Control Module. The PCM transmits
the VIN message every 14 seconds.
Set Condition: With ignition on, If the ORC does not receive the 2 consecutive matching
(vehicle Body Style) VIN messages on the bus the code will set.
80
AIRBAG
ORC, CALIBRATION MISMATCH - STORED ÐContinued