ECU CHRYSLER VOYAGER 2004 Service Manual

The Task Manager Screen shows both a Requested
MIL state and an Actual MIL state. When the MIL is
illuminated upon completion of a test for a good trip,
the Requested MIL state changes to OFF. However,
the MIL remains illuminated until the next key
cycle. (On some vehicles, the MIL will actually turn
OFF during the thirdgood trip) During the key cycle
for the third good trip, the Requested MIL state is
OFF, while the Actual MIL state is ON. After the
next key cycle, the MIL is not illuminated and both
MIL states read OFF.
Diagnostic Trouble Codes (DTCs)
With OBD II, different DTC faults have different
priorities according to regulations. As a result, the
priorities determine MIL illumination and DTC era-
sure. DTCs are entered according to individual prior-
ity. DTCs with a higher priority overwrite lower
priority DTCs.
Priorities
²Priority 0 ÐNon-emissions related trouble codes.
²Priority 1 Ð One trip failure of a two trip fault
for non-fuel system and non-misfire. (MIL Off)
²Priority 2 Ð One trip failure of a two trip fault
for fuel system (rich/lean) or misfire. (MIL Off)
²Priority3ÐTwotrip failure for a non-fuel sys-
tem and non-misfire or matured one trip comprehen-
sive component fault. (MIL On)
²Priority4ÐTwotrip failure or matured fault
for fuel system (rich/lean) and misfire or one trip cat-
alyst damaging misfire. Catalyst damage misfire is a
2 trip MIL. The MIL flashes on the first trip when
catalyst damage misfire levels are present. (MIL On)
Non-emissions related failures have no priority.
One trip failures of two trip faults have low priority.
Two trip failures or matured faults have higher pri-
ority. One and two trip failures of fuel system and
misfire monitor take precedence over non-fuel system
and non-misfire failures.
DTC Self Erasure
With one trip components or systems, the MIL is
illuminated upon test failure and DTCs are stored.
Two trip monitors are components requiring failure
in two consecutive trips for MIL illumination. Upon
failure of the first test, the Task Manager enters a
maturing code. If the component fails the test for a
second time the code matures and a DTC is set.
After three good trips the MIL is extinguished and
the Task Manager automatically switches the trip
counter to a warm-up cycle counter. DTCs are auto-
matically erased following 40 warm-up cycles if the
component does not fail again.
For misfire and fuel system monitors, the compo-
nent must pass the test under a Similar Conditions
Window in order to record a good trip. A Similar Con-ditions Window is when engine RPM is within  375
RPM and load is within  20% of when the fault
occurred.
NOTE: It is important to understand that a compo-
nent does not have to fail under a similar window of
operation to mature. It must pass the test under a
Similar Conditions Window when it failed to record
a Good Trip for DTC erasure for misfire and fuel
system monitors.
DTCs can be erased anytime with a DRBIIIt.
Erasing the DTC with the DRBIIIterases all OBD II
information. The DRBIIItautomatically displays a
warning that erasing the DTC will also erase all
OBD II monitor data. This includes all counter infor-
mation for warm-up cycles, trips and Freeze Frame.
Trip Indicator
TheTripis essential for running monitors and
extinguishing the MIL. In OBD II terms, a trip is a
set of vehicle operating conditions that must be met
for a specific monitor to run. All trips begin with a
key cycle.
Good Trip
The Good Trip counters are as follows:
²Global Good Trip
²Fuel System Good Trip
²Misfire Good Trip
²Alternate Good Trip (appears as a Global Good
Trip on DRBIIIt)
²Comprehensive Components
²Major Monitor
²Warm-Up Cycles
Global Good Trip
To increment a Global Good Trip, the Oxygen sen-
sor and Catalyst efficiency monitors must have run
and passed, and 2 minutes of engine run time.
Fuel System Good Trip
To count a good trip (three required) and turn off
the MIL, the following conditions must occur:
²Engine in closed loop
²Operating in Similar Conditions Window
²Short Term multiplied by Long Term less than
threshold
²Less than threshold for a predetermined time
If all of the previous criteria are met, the PCM will
count a good trip (three required) and turn off the
MIL.
Misfire Good Trip
If the following conditions are met the PCM will
count one good trip (three required) in order to turn
off the MIL:
²Operating in Similar Condition Window
²1000 engine revolutions with no misfire
RSON-BOARD DIAGNOSTICS25-25
TASK MANAGER (Continued)

SEAT TRACK MANUAL ADJUSTER -
INSTALLATION, FRONT................23-95
SEAT TRACK MANUAL ADJUSTER -
REMOVAL, FRONT....................23-95
SEAT TRACK POWER ADJUSTER -
INSTALLATION, FRONT................23-95
SEAT TRACK POWER ADJUSTER -
REMOVAL, FRONT....................23-95
SEATBACK ASSIST STRAP -
INSTALLATION, FRONT................23-92
SEATBACK ASSIST STRAP - REMOVAL,
FRONT.............................23-92
SEATBACK COVER - INSTALLATION,
FRONT.............................23-93
SEATBACK COVER - REMOVAL, FRONT . . . 23-93
SEATBACK PANEL - INSTALLATION,
BENCH.............................23-99
SEATBACK PANEL - INSTALLATION,
FRONT.............................23-93
SEATBACK PANEL - REMOVAL, BENCH . . . 23-99
SEATBACK PANEL - REMOVAL, FRONT....23-92
SEAT/MIRROR MODULE - DESCRIPTION,
MEMORY...........................8E-10
SEAT/MIRROR MODULE - DIAGNOSIS
AND TESTING, MEMORY...............8E-10
SEAT/MIRROR MODULE -
INSTALLATION, MEMORY..............8E-10
SEAT/MIRROR MODULE - OPERATION,
MEMORY...........................8E-10
SEAT/MIRROR MODULE - REMOVAL,
MEMORY...........................8E-10
SEATS - CLEANING, INTAKE/EXHAUST
VALVES.....................9-105,9-32,9s-22
SEATS - DESCRIPTION, INTAKE/
EXHAUST VALVES...........9-104,9-32,9s-21
SEATS - INSPECTION, INTAKE/EXHAUST
VALVES .......................9-105,9s-22
SEATS - INSTALLATION, INTAKE/
EXHAUST VALVES...............9-106,9s-23
SEATS - OPERATION, INTAKE/EXHAUST
VALVES .......................9-104,9s-21
SEATS - REMOVAL, INTAKE/EXHAUST
VALVES .......................9-105,9s-22
SEATS - STANDARD PROCEDURE,
REFACING VALVES AND VALVE.....9-104,9s-21
SECOND ROW - INSTALLATION, BENCH
SEAT RISER........................23-101
SECOND ROW - LEFT OUTBOARD -
INSTALLATION, SEAT BELT &
RETRACTOR........................8O-17
SECOND ROW - LEFT OUTBOARD -
REMOVAL, SEAT BELT & RETRACTOR....8O-17
SECOND ROW - REMOVAL, BENCH SEAT
RISER............................23-101
SECOND ROW - RIGHT OUTBOARD -
INSTALLATION, SEAT BELT &
RETRACTOR........................8O-15
SECOND ROW - RIGHT OUTBOARD -
REMOVAL, SEAT BELT & RETRACTOR
....8O-15
SECOND ROW - RIGHT OUTBOARD
WITH REAR HVAC - LWB -
INSTALLATION, SEAT BELT &
RETRACTOR
........................8O-16
SECOND ROW - RIGHT OUTBOARD
WITH REAR HVAC - LWB - REMOVAL,
SEAT BELT & RETRACTOR
.............8O-16
SECOND ROW - THREE PASSENGER
BENCH - INSTALLATION, SEAT BELT
BUCKLE
............................8O-15
SECOND ROW - THREE PASSENGER
BENCH - REMOVAL, SEAT BELT
BUCKLE
............................8O-15
SECOND ROW INBOARD - 50/50 BENCH
- INSTALLATION, SEAT BELT BUCKLE
....8O-13
SECOND ROW INBOARD - 50/50 BENCH
- REMOVAL, SEAT BELT BUCKLE
........8O-13
SECTION IDENTIFICATION AND
INFORMATION - DESCRIPTION
........8W-01-6
SECURITY - DESCRIPTION, VEHICLE
THEFT
..............................8Q-1
SECURITY - OPERATION, VEHICLE THEFT
. . 8Q-1
SECURITY SYSTEM - DIAGNOSIS AND
TESTING, VEHICLE THEFT
..............8Q-3
SELECTION, ADJUSTMENTS - OUTPUT
FLANGE SHIM
........................21-7
SELECTOR - INSTALLATION, GEARSHIFT
CABLE
.............................21-84SELECTOR - REMOVAL, GEARSHIFT
CABLE.............................21-81
SELF-DIAGNOSTICS - DIAGNOSIS AND
TESTING............................8J-2
SENDING UNIT / SENSOR -
DESCRIPTION, FUEL LEVEL.............14-5
SENDING UNIT / SENSOR -
INSTALLATION, FUEL LEVEL.............14-5
SENDING UNIT / SENSOR - OPERATION,
FUEL LEVEL..........................14-5
SENDING UNIT / SENSOR - REMOVAL,
FUEL LEVEL..........................14-5
SENSE - PCM INPUT - OPERATION,
IGNITION...........................8E-15
SENSITIVE DEVICES - STANDARD
PROCEDURE, ELECTROSTATIC
DISCHARGE (ESD).................8W-01-8
SENSOR - 2.4L - DESCRIPTION, ENGINE
COOLANT TEMPERATURE...............7-21
SENSOR - 2.4L - INSTALLATION, ENGINE
COOLANT TEMPERATURE...............7-21
SENSOR - 2.4L - REMOVAL, ENGINE
COOLANT TEMPERATURE...............7-21
SENSOR - 3.3/3.8L - DESCRIPTION,
ENGINE COOLANT TEMPERATURE........7-21
SENSOR - 3.3/3.8L - INSTALLATION,
ENGINE COOLANT TEMPERATURE........7-22
SENSOR - 3.3/3.8L - REMOVAL, ENGINE
COOLANT TEMPERATURE...............7-21
SENSOR - AWD - INSTALLATION, REAR
WHEEL SPEED........................5-80
SENSOR - AWD - REMOVAL, REAR
WHEEL SPEED........................5-80
SENSOR - DESCRIPTION, AMBIENT
TEMP.............................8M-11
SENSOR - DESCRIPTION, BATTERY
TEMPERATURE......................8F-23
SENSOR - DESCRIPTION, CAMSHAFT
POSITION............................8I-4
SENSOR - DESCRIPTION, CRANKSHAFT
POSITION..........................14-25
SENSOR - DESCRIPTION, ENGINE SPEED . 14-26
SENSOR - DESCRIPTION, EVAPORATOR
TEMPERATURE......................24-27
SENSOR - DESCRIPTION, FUEL LEVEL
SENDING UNIT.......................14-5
SENSOR - DESCRIPTION, HEATED SEAT . . 8G-12
SENSOR - DESCRIPTION, INFRARED
TEMPERATURE......................24-29
SENSOR - DESCRIPTION, INLET AIR
TEMPERATURE......................14-30
SENSOR - DESCRIPTION, KNOCK.........8I-8
SENSOR - DESCRIPTION, MAP..........14-30
SENSOR - DESCRIPTION, O2...........14-32
SENSOR - DESCRIPTION, PINCH........8N-17
SENSOR - DESCRIPTION, THROTTLE
POSITION..........................14-36
SENSOR - DESCRIPTION,
TRANSMISSION RANGE.......21-248,21s-150
SENSOR - DIAGNOSIS AND TESTING,
AMBIENT TEMPERATURE..............8M-12
SENSOR - DIAGNOSIS AND TESTING,
HEATED SEAT .......................8G-12
SENSOR - DIAGNOSIS AND TESTING,
TIRE PRESSURE
................22-10,22s-2
SENSOR - FWD - INSTALLATION, REAR
WHEEL SPEED
........................5-81
SENSOR - FWD - REMOVAL, REAR
WHEEL SPEED
........................5-81
SENSOR - INPUT - DESCRIPTION,
SPEED
.....................21-239,21s-140
SENSOR - INPUT - INSTALLATION,
SPEED
.....................21-240,21s-141
SENSOR - INPUT - OPERATION, SPEED
. 21-240,
21s-140
SENSOR - INPUT - REMOVAL, SPEED
. . . 21-240,
21s-141
SENSOR - INSTALLATION, FRONT
WHEEL SPEED
........................5-80
SENSOR - INSTALLATION, FUEL LEVEL
SENDING UNIT
.......................14-5
SENSOR - INSTALLATION, PINCH
........8N-17
SENSOR - INSTALLATION,
TRANSMISSION RANGE
.......21-249,21s-152
SENSOR - INSTALLATION, VEHICLE
SPEED
............................21-115
SENSOR - OPERATION, AMBIENT TEMP
. . 8M-11SENSOR - OPERATION, BATTERY
TEMPERATURE......................8F-23
SENSOR - OPERATION, CAMSHAFT
POSITION............................8I-4
SENSOR - OPERATION, CRANKSHAFT
POSITION..........................14-25
SENSOR - OPERATION, ENGINE SPEED . . . 14-26
SENSOR - OPERATION, EVAPORATOR
TEMPERATURE......................24-28
SENSOR - OPERATION, FUEL LEVEL
SENDING UNIT.......................14-5
SENSOR - OPERATION, HEATED SEAT....8G-12
SENSOR - OPERATION, INFRARED
TEMPERATURE......................24-29
SENSOR - OPERATION, KNOCK...........8I-8
SENSOR - OPERATION, MAP...........14-30
SENSOR - OPERATION, O2.............14-32
SENSOR - OPERATION, PINCH..........8N-17
SENSOR - OPERATION, THROTTLE
POSITION..........................14-36
SENSOR - OPERATION, TRANSMISSION
RANGE.....................21-248,21s-151
SENSOR - OUTPUT - DESCRIPTION,
SPEED.....................21-241,21s-142
SENSOR - OUTPUT - INSTALLATION,
SPEED.....................21-242,21s-143
SENSOR - OUTPUT - OPERATION,
SPEED.....................21-241,21s-142
SENSOR - OUTPUT - REMOVAL, SPEED . 21-241,
21s-143
SENSOR - REMOVAL, BATTERY
TEMPERATURE........................8F-23
SENSOR - REMOVAL, CRANKSHAFT
POSITION..........................14-25
SENSOR - REMOVAL, FRONT WHEEL
SPEED..............................5-79
SENSOR - REMOVAL, FUEL LEVEL
SENDING UNIT.......................14-5
SENSOR - REMOVAL, PINCH...........8N-17
SENSOR - REMOVAL, TRANSMISSION
RANGE.....................21-249,21s-151
SENSOR - REMOVAL, VEHICLE SPEED . . . 21-115
SENSOR - SPECIFICATIONS, BATTERY
TEMPERATURE......................8F-22
SENSOR - TPM - CAUTION........22-10,22s-2
SENSOR - TPM - DESCRIPTION....22-10,22s-1
SENSOR - TPM - INSTALLATION....22-12,22s-3
SENSOR - TPM - OPERATION......22-10,22s-2
SENSOR - TPM - REMOVAL.......22-11,22s-2
SENSOR AIR GAP, SPECIFICATIONS -
WHEEL SPEED........................5-79
SENSOR CIRCUIT - DIAGNOSIS AND
TESTING, AMBIENT TEMPERATURE......8M-12
SENSOR RETRAIN - STANDARD
PROCEDURE, TIRE PRESSURE.....22-10,22s-2
SENSOR RETURN - PCM INPUT -
OPERATION.........................8E-15
SENTRY KEY IMMOBILIZER MODULE -
DESCRIPTION.......................8E-18
SENTRY KEY IMMOBILIZER MODULE -
INSTALLATION.......................8E-19
SENTRY KEY IMMOBILIZER MODULE -
OPERATION.........................8E-18
SENTRY KEY IMMOBILIZER MODULE -
REMOVAL..........................8E-18
SENTRY KEY REMOTE ENTRY MODULE -
DESCRIPTION
........................8Q-3
SENTRY KEY REMOTE ENTRY MODULE -
DIAGNOSIS AND TESTING
..............8Q-5
SENTRY KEY REMOTE ENTRY MODULE -
INSTALLATION
.......................8Q-6
SENTRY KEY REMOTE ENTRY MODULE -
OPERATION
..........................8Q-4
SENTRY KEY REMOTE ENTRY MODULE -
REMOVAL
...........................8Q-5
SENTRY KEY REMOTE ENTRY SYSTEM -
DIAGNOSIS AND TESTING
..............8Q-3
SERVO - DESCRIPTION
.................8P-4
SERVO - INSTALLATION
................8P-5
SERVO - OPERATION
..................8P-4
SERVO - REMOVAL
....................8P-5
SET SWITCH - DESCRIPTION,
MEMORY
.....................8N-12,8N-55
SET SWITCH - INSTALLATION,
MEMORY
.....................8N-13,8N-56
SET SWITCH - OPERATION,
MEMORY
.....................8N-13,8N-56
RSINDEX31
Description Group-Page Description Group-Page Description Group-Page

SWITCH - REMOVAL, LEFT B-PILLAR....8N-32
SWITCH - REMOVAL, MEMORY SET.....8N-13,
8N-56
SWITCH - REMOVAL, MULTI-FUNCTION . . . 8L-18
SWITCH - REMOVAL, OIL PRESSURE....9-141,
9-54
SWITCH - REMOVAL, PASSENGER
HEATED SEAT .......................8G-14
SWITCH - REMOVAL, PASSENGER SEAT . . 8N-14,
8N-57
SWITCH - REMOVAL, REMOTE..........8N-49
SWITCH - REMOVAL, RIGHT B-PILLAR . . . 8N-32
SWITCH - REMOVAL, SUNROOF........23-123
SWITCH - REMOVAL, WASHER FLUID
LEVEL.............................8R-12
SWITCH - REMOVAL, WINDOW.........8N-65
SWITCH ASSY - DESCRIPTION,
SOLENOID/PRESSURE.........21-237,21s-137
SWITCH ASSY - INSTALLATION,
SOLENOID/PRESSURE.........21-239,21s-139
SWITCH ASSY - OPERATION, SOLENOID/
PRESSURE..................21-237,21s-137
SWITCH ASSY - REMOVAL, SOLENOID/
PRESSURE..................21-238,21s-138
SWITCHES - DESCRIPTION, REMOTE.....8A-12
SWITCHES - DIAGNOSIS AND TESTING,
REMOTE...........................8A-12
SWITCHES - INSTALLATION, REMOTE....8A-14
SWITCHES - OPERATION, REMOTE......8A-12
SWITCHES - REMOVAL, REMOTE........8A-13
SYMBOLS - DESCRIPTION,
INTERNATIONAL....................Intro.-5
SYMBOLS - DESCRIPTION,
INTERNATIONAL.......................0-1
SYNCHRONIZER - DESCRIPTION.......21-114
SYNCHRONIZER - DISASSEMBLY.......21-114
SYNCHRONIZING CABLE ADJUSTMENT,
INSTALLATION.................23-102,23-88
T850 MANUAL TRANSAXLE - ASSEMBLY . . 21-42
T850 MANUAL TRANSAXLE -
DESCRIPTION.......................21-21
T850 MANUAL TRANSAXLE -
DISASSEMBLY.......................21-35
T850 MANUAL TRANSAXLE -
INSTALLATION.......................21-51
T850 MANUAL TRANSAXLE -
OPERATION.........................21-24
T850 MANUAL TRANSAXLE - REMOVAL . . 21-31
T850 MANUAL TRANSAXLE -
SPECIFICATIONS.....................21-56
T850 TRANSAXLE - SPECIAL TOOLS.......6-6
T850 TRANSAXLE - SPECIAL TOOLS.....21-58
TABLE, SPECIFICATIONS -
SPECIFICATIONS.................8N-29,8N-9
TAIL LAMP - INSTALLATION............8L-19
TAIL LAMP - REMOVAL................8L-18
TAIL LAMP UNIT - INSTALLATION.......8L-19
TAIL LAMP UNIT - REMOVAL...........8L-19
TANK - DESCRIPTION, FUEL............14-10
TANK - INSTALLATION, FUEL...........14-12
TANK - OPERATION, FUEL..............14-11
TANK - REMOVAL, FUEL...............14-11
TANK - STANDARD PROCEDURE,
DRAINING FUEL......................14-2
TANK FILLER TUBE - INSTALLATION,
FUEL..............................14-13
TANK FILLER TUBE - REMOVAL, FUEL....14-12
TAPE ATTACHED - INSTALLATION,
EXTERIOR NAME PLATES..............23-51
TAPE ATTACHED - REMOVAL, EXTERIOR
NAME PLATES.......................23-51
TASK MANAGER - DESCRIPTION........25-24
TASK MANAGER - OPERATION..........25-24
TD - INSTALLATION, CLUTCH DISC AND
PRESSURE PLATE - 2.5L...............6-12
TD - REMOVAL, CLUTCH DISC AND
PRESSURE PLATE - 2.5L...............6-11
TEMP SENSOR - DESCRIPTION,
AMBIENT..........................8M-11
TEMP SENSOR - OPERATION, AMBIENT
. . 8M-11
TEMPERATURE CONTROL (ATC) -
INSTALLATION, AUTOMATIC
............24-29
TEMPERATURE CONTROL (ATC) -
REMOVAL, AUTOMATIC
................24-28
TEMPERATURE CONTROL (MTC) -
INSTALLATION, MANUAL
..............24-29
TEMPERATURE CONTROL (MTC) -
REMOVAL, MANUAL
..................24-29TEMPERATURE CONTROL SYSTEM -
OPERATION, AUTOMATIC.............24-112
TEMPERATURE CONTROL SYSTEM -
OPERATION, MANUAL................24-112
TEMPERATURE SENSOR - 2.4L -
DESCRIPTION, ENGINE COOLANT.........7-21
TEMPERATURE SENSOR - 2.4L -
INSTALLATION, ENGINE COOLANT........7-21
TEMPERATURE SENSOR - 2.4L -
REMOVAL, ENGINE COOLANT............7-21
TEMPERATURE SENSOR - 3.3/3.8L -
DESCRIPTION, ENGINE COOLANT.........7-21
TEMPERATURE SENSOR - 3.3/3.8L -
INSTALLATION, ENGINE COOLANT........7-22
TEMPERATURE SENSOR - 3.3/3.8L -
REMOVAL, ENGINE COOLANT............7-21
TEMPERATURE SENSOR - DESCRIPTION,
BATTERY...........................8F-23
TEMPERATURE SENSOR - DESCRIPTION,
EVAPORATOR.......................24-27
TEMPERATURE SENSOR - DESCRIPTION,
INFRARED..........................24-29
TEMPERATURE SENSOR - DESCRIPTION,
INLET AIR..........................14-30
TEMPERATURE SENSOR - DIAGNOSIS
AND TESTING, AMBIENT..............8M-12
TEMPERATURE SENSOR - OPERATION,
BATTERY...........................8F-23
TEMPERATURE SENSOR - OPERATION,
EVAPORATOR.......................24-28
TEMPERATURE SENSOR - OPERATION,
INFRARED..........................24-29
TEMPERATURE SENSOR - REMOVAL,
BATTERY.............................8F-23
TEMPERATURE SENSOR -
SPECIFICATIONS, BATTERY.............8F-22
TEMPERATURE SENSOR CIRCUIT -
DIAGNOSIS AND TESTING, AMBIENT....8M-12
TENSION - STANDARD PROCEDURE,
CHECKING POWER STEERING BELT........7-8
TENSION RELEASE - STANDARD
PROCEDURE, PARKING BRAKE
AUTOMATIC ADJUSTER............5-58,5s-61
TENSION RESET - STANDARD
PROCEDURE, PARKING BRAKE
AUTOMATIC ADJUSTER............5-59,5s-61
TENSION, SPECIFICATIONS -
ACCESSORY DRIVE BELT................7-5
TENSIONER - 2.4L - INSTALLATION,
BELT ...............................7-10
TENSIONER - 2.4L - REMOVAL, BELT......7-10
TENSIONER - 3.3/3.8L - INSTALLATION,
BELT ...............................7-12
TENSIONER - 3.3/3.8L - REMOVAL, BELT . . . 7-12
TENSIONER - DESCRIPTION, SEAT BELT . . 8O-17
TENSIONER - OPERATION, SEAT BELT....8O-17
TENSIONER & PULLEY - INSTALLATION,
TIMING BELT.........................9-69
TENSIONER & PULLEY - REMOVAL,
TIMING BELT.........................9-68
TERMINAL - INSTALLATION.........8W-01-14
TERMINAL - REMOVAL.............8W-01-14
TERMINAL REPAIR - STANDARD
PROCEDURE, GRID LINE...............8G-4
TEST - 2.5L DIESEL - DIAGNOSIS AND
TESTING, SYSTEM CHARGE LEVEL......24-68
TEST - DIAGNOSIS AND TESTING, A/C
COOL DOWN.........................24-6
TEST - DIAGNOSIS AND TESTING, A/C
PERFORMANCE.......................24-7
TEST - DIAGNOSIS AND TESTING,
CONTROL CIRCUIT..............8F-30,8F-32
TEST - DIAGNOSIS AND TESTING,
COOLING SYSTEM LEAK.................7-2
TEST - DIAGNOSIS AND TESTING,
CYLINDER COMBUSTION PRESSURE
LEAKAGE.........................9-83,9-9
TEST - DIAGNOSIS AND TESTING,
CYLINDER COMPRESSION PRESSURE
. . 9-83,9-9
TEST - DIAGNOSIS AND TESTING, FEED
CIRCUIT
.......................8F-33,8F-35
TEST - DIAGNOSIS AND TESTING, FEED
CIRCUIT RESISTANCE
............8F-32,8F-34
TEST - DIAGNOSIS AND TESTING,
HEATER PERFORMANCE
...............24-10
TEST - DIAGNOSIS AND TESTING,
POWER STEERING SYSTEM FLOW
AND PRESSURE
......................19-1TEST - DIAGNOSIS AND TESTING, ROAD . . . 8P-3
TEST - DIAGNOSIS AND TESTING,
ROAD.......................21-119,21s-27
TEST - DIAGNOSIS AND TESTING,
STARTING SYSTEM..............8F-28,8F-30
TEST - GASOLINE ENGINES -
DIAGNOSIS AND TESTING, SYSTEM
CHARGE LEVEL......................24-67
TEST - STANDARD PROCEDURE,
IGNITION-OFF DRAW..................8F-13
TEST - STANDARD PROCEDURE,
OPEN-CIRCUIT VOLTAGE...............8F-13
TEST MODE, OPERATION - DRB IIIT
STATE DISPLAY.......................25-9
TESTS - DIAGNOSIS AND TESTING,
CLUTCH AIR PRESSURE........21-122,21s-30
TESTS - DIAGNOSIS AND TESTING,
HYDRAULIC PRESSURE........21-120,21s-28
THEFT SECURITY - DESCRIPTION,
VEHICLE............................8Q-1
THEFT SECURITY - OPERATION, VEHICLE . . 8Q-1
THEFT SECURITY SYSTEM - DIAGNOSIS
AND TESTING, VEHICLE................8Q-3
THERMOSTAT - 2.4L - INSTALLATION,
ENGINE COOLANT.....................7-23
THERMOSTAT - 2.4L - REMOVAL,
ENGINE COOLANT.....................7-23
THERMOSTAT - 3.3/3.8L -
INSTALLATION, ENGINE COOLANT........7-24
THERMOSTAT - 3.3/3.8L - REMOVAL,
ENGINE COOLANT.....................7-23
THERMOSTAT - DESCRIPTION, ENGINE
COOLANT............................7-22
THERMOSTAT - DIAGNOSIS AND
TESTING, ENGINE COOLANT.............7-23
THERMOSTAT - OPERATION, ENGINE
COOLANT............................7-22
THERMOWRAP - DESCRIPTION.........8F-19
THERMOWRAP - INSTALLATION.........8F-19
THERMOWRAP - OPERATION...........8F-19
THERMOWRAP - REMOVAL............8F-19
THIRD ROW - INSTALLATION, BENCH
SEAT RISER........................23-101
THIRD ROW - REMOVAL, BENCH SEAT
RISER............................23-101
THREAD REPAIR - DESCRIPTION, FRONT
CRADLE CROSSMEMBER...............13-9
THREAD REPAIR - STANDARD
PROCEDURE, MANIFOLD STRIPPED......9-145
THREADED HOLE REPAIR -
DESCRIPTION......................Intro.-5
THREADS - STANDARD PROCEDURE,
REPAIR OF DAMAGED OR WORN.....9-10,9-86
THREE PASSENGER BENCH -
INSTALLATION, SEAT BELT BUCKLE -
SECOND ROW.......................8O-15
THREE PASSENGER BENCH - REMOVAL,
SEAT BELT BUCKLE - SECOND ROW.....8O-15
THREE ZONE - DESCRIPTION,
AUTOMATIC..........................24-3
THREE ZONE - DESCRIPTION, MANUAL....24-2
THREE ZONE - OPERATION, MANUAL.....24-5
THREE ZONE ATC - OPERATION..........24-5
THROTTLE BODY - DESCRIPTION........14-35
THROTTLE BODY - INSTALLATION.......14-35
THROTTLE BODY - OPERATION.........14-35
THROTTLE BODY - REMOVAL...........14-35
THROTTLE CONTROL CABLE -
INSTALLATION.......................14-36
THROTTLE CONTROL CABLE - REMOVAL . . 14-35
THROTTLE POSITION SENSOR -
DESCRIPTION.......................14-36
THROTTLE POSITION SENSOR -
OPERATION.........................14-36
TIE ROD - INSTALLATION, OUTER.......19-34
TIE ROD - REMOVAL, OUTER...........19-34
TIMING BELT - INSTALLATION...........9-65
TIMING BELT - REMOVAL...............9-63
TIMING BELT COVER(S) - INSTALLATION . . . 9-62
TIMING BELT COVER(S) - REMOVAL
......9-61
TIMING BELT TENSIONER & PULLEY -
INSTALLATION
........................9-69
TIMING BELT TENSIONER & PULLEY -
REMOVAL
...........................9-68
TIMING CHAIN AND CAMSHAFT
SPROCKET - INSTALLATION
............9-157
TIMING CHAIN AND CAMSHAFT
SPROCKET - REMOVAL
................9-156
RSINDEX35
Description Group-Page Description Group-Page Description Group-Page

VALVE (HEIGHT SENSING) -
DESCRIPTION, PROPORTIONING....5-48,5s-51
VALVE (HEIGHT SENSING) - DIAGNOSIS
AND TESTING, PROPORTIONING....5-49,5s-52
VALVE (HEIGHT SENSING) -
INSTALLATION, PROPORTIONING....5-51,5s-53
VALVE (HEIGHT SENSING) - OPERATION,
PROPORTIONING.................5-48,5s-51
VALVE (HEIGHT SENSING) - REMOVAL,
PROPORTIONING.................5-50,5s-53
VALVE SEATS - STANDARD PROCEDURE,
REFACING VALVES...............9-104,9s-21
VALVE SPRINGS - DESCRIPTION . . . 9-106,9s-23
VALVE SPRINGS - OPERATION.....9-106,9s-23
VALVE STEM SEALS - DESCRIPTION.....9-111,
9s-29
VALVE STEM SEALS - INSTALLATION....9-112,
9s-29
VALVE STEM SEALS - REMOVAL . . . 9-112,9s-29
VALVE TIMING VERIFICATION -
STANDARD PROCEDURE...............9-153
VALVES - OPERATION, HYDRAULIC
CIRCUITS............................5-83
VALVES & SEATS - CLEANING,
INTAKE/EXHAUST...........9-105,9-32,9s-22
VALVES & SEATS - DESCRIPTION,
INTAKE/EXHAUST...........9-104,9-32,9s-21
VALVES & SEATS - INSPECTION,
INTAKE/EXHAUST...............9-105,9s-22
VALVES & SEATS - INSTALLATION,
INTAKE/EXHAUST...............9-106,9s-23
VALVES & SEATS - OPERATION,
INTAKE/EXHAUST.................9-104,9s-21
VALVES & SEATS - REMOVAL,
INTAKE/EXHAUST...............9-105,9s-22
VALVES AND VALVE SEATS - STANDARD
PROCEDURE, REFACING..........9-104,9s-21
VANITY LAMP - INSTALLATION.........8L-24
VANITY LAMP - REMOVAL.............8L-24
VAPOR CANISTER - DESCRIPTION.......25-18
VAPOR CANISTER - OPERATION.........25-18
VARIABLE BRAKE PROPORTIONING -
DESCRIPTION, ELECTRONIC.............5-75
VARIABLE BRAKE PROPORTIONING -
OPERATION, ELECTRONIC...............5-77
VARIATION ADJUSTMENT - STANDARD
PROCEDURE, COMPASS...............8M-5
VECI LABEL - DESCRIPTION..........Intro.-11
VEHICLE CERTIFICATION LABEL -
DESCRIPTION.....................Intro.-11
VEHICLE DOES NOT FILL - DIAGNOSIS
AND TESTING.......................25-16
VEHICLE EMISSION CONTROL
INFORMATION LABEL - DESCRIPTION.....25-1
VEHICLE IDENTIFICATION -
DESCRIPTION........................23-1
VEHICLE IDENTIFICATION NUMBER -
DESCRIPTION......................Intro.-9
VEHICLE INFO CENTER - DESCRIPTION,
ELECTRONIC........................8M-6
VEHICLE INFO CENTER - INSTALLATION,
ELECTRONIC........................8M-9
VEHICLE INFO CENTER - OPERATION,
ELECTRONIC........................8M-7
VEHICLE INFO CENTER - REMOVAL,
ELECTRONIC........................8M-9
VEHICLE INFORMATION CENTER -
DIAGNOSIS AND TESTING,
ELECTRONIC........................8M-7
VEHICLE INFORMATION CENTER
PROGRAMMING - STANDARD
PROCEDURE, ELECTRONIC.............8M-7
VEHICLE SPEED SENSOR -
INSTALLATION......................21-115
VEHICLE SPEED SENSOR - REMOVAL . . . 21-115
VEHICLE THEFT SECURITY -
DESCRIPTION........................8Q-1
VEHICLE THEFT SECURITY - OPERATION . . 8Q-1
VEHICLE THEFT SECURITY SYSTEM -
DIAGNOSIS AND TESTING..............8Q-3
VENT WINDOW MOTOR - DIAGNOSIS
AND TESTING
.......................8N-63
VENT WINDOW MOTOR - INSTALLATION
. . 8N-64
VENT WINDOW MOTOR - REMOVAL
.....8N-63
VERIFICATION - STANDARD
PROCEDURE, VALVE TIMING
...........9-153
VIBRATION - DIAGNOSIS AND TESTING,
TIRE AND WHEEL
.....................22-1VIBRATION DAMPER - INSTALLATION....9-130,
9-47
VIBRATION DAMPER - REMOVAL....9-130,9-47
VIDEO SCREEN - DESCRIPTION.........8A-16
VIDEO SCREEN - INSTALLATION........8A-16
VIDEO SCREEN - OPERATION...........8A-16
VIDEO SCREEN - REMOVAL............8A-16
VIEW MIRROR - INSTALLATION, REAR . . . 23-81
VIEW MIRROR - INSTALLATION, SIDE....23-59
VIEW MIRROR - REMOVAL, REAR.......23-81
VIEW MIRROR - REMOVAL, SIDE........23-59
VIEW MIRROR GLASS - INSTALLATION,
SIDE..............................23-59
VIEW MIRROR GLASS - REMOVAL, SIDE . . 23-59
VISCOUS COUPLER - DESCRIPTION.......3-41
VISCOUS COUPLER - OPERATION........3-42
VISOR - INSTALLATION, SUN...........23-82
VISOR - REMOVAL, SUN...............23-82
VISOR SUPPORT - INSTALLATION, SUN . . . 23-83
VISOR SUPPORT - REMOVAL, SUN......23-83
VOLT SUPPLY - PCM OUTPUT -
OPERATION, 5.......................8E-15
VOLTAGE DROP - STANDARD
PROCEDURE, TESTING FOR A.......8W-01-10
VOLTAGE POTENTIAL - STANDARD
PROCEDURE, TESTING OF...........8W-01-9
VOLTAGE REGULATOR - DESCRIPTION . . . 8F-27,
8F-29
VOLTAGE REGULATOR - OPERATION.....8F-27,
8F-29
VOLTAGE TEST - STANDARD
PROCEDURE, OPEN-CIRCUIT...........8F-13
VTSS/SKIS INDICATOR LAMP -
DESCRIPTION........................8Q-7
VTSS/SKIS INDICATOR LAMP -
OPERATION..........................8Q-8
WARNING - A/C SYSTEM..............24-65
WARNING - ENGINE COOLING SYSTEM . . . 24-65
WARNING - INSTALLATION............23-109
WARNING - INSTALLATION.............19-13
WARNING - REMOVAL...............23-108
WARNING - REMOVAL................19-12
WARNING - SAFETY PRECAUTIONS AND
WARNINGS..........................23-1
WARNING - WARNINGS AND CAUTIONS . . 19-10,
19-27
WARNING - WINDSHIELD SAFETY
PRECAUTIONS......................23-108
WARNING, CHIME/BUZZER..............8B-1
WARNING, DESCRIPTION............5-4,5s-3
WARNING, DESCRIPTION..............19-37
WARNING, LAMPS/LIGHTING -
EXTERIOR...........................8L-3
WARNING, RESTRAINTS................8O-2
WARNINGS AND CAUTIONS, WARNING . . 19-10,
19-27
WARNINGS, GENERAL..............8W-01-7
WARNINGS, WARNING - SAFETY
PRECAUTIONS........................23-1
WASHER FLUID LEVEL SWITCH -
INSTALLATION......................8R-12
WASHER FLUID LEVEL SWITCH -
REMOVAL..........................8R-12
WASHER HOSES - INSTALLATION.......8R-13
WASHER HOSES - REMOVAL...........8R-13
WASHER PUMP MOTOR -
INSTALLATION, FRONT.................8R-8
WASHER PUMP MOTOR -
INSTALLATION, REAR.................8R-10
WASHER PUMP MOTOR - REMOVAL,
FRONT..............................8R-8
WASHER PUMP MOTOR - REMOVAL,
REAR..............................8R-10
WASHER RESERVOIR - INSTALLATION . . . 8R-13
WASHER RESERVOIR - REMOVAL.......8R-13
WASHER SYSTEM - DIAGNOSIS AND
TESTING............................8R-4
WATER CHANNEL - INSTALLATION......23-121
WATER CHANNEL - REMOVAL.........23-121
WATER LEAKS - DIAGNOSIS AND
TESTING............................23-1
WATER PUMP - 2.4L - CLEANING........7-32
WATER PUMP - 2.4L - DESCRIPTION......7-31
WATER PUMP - 2.4L - INSPECTION
.......7-32
WATER PUMP - 2.4L - INSTALLATION
.....7-32
WATER PUMP - 2.4L - REMOVAL
.........7-31
WATER PUMP - 3.3/3.8L - CLEANING
.....7-34
WATER PUMP - 3.3/3.8L - DESCRIPTION
. . . 7-33WATER PUMP - 3.3/3.8L - INSPECTION....7-34
WATER PUMP - 3.3/3.8L -
INSTALLATION........................7-34
WATER PUMP - 3.3/3.8L - REMOVAL......7-33
WATER PUMP INLET TUBE - 2.4L -
DESCRIPTION........................7-35
WATER PUMP INLET TUBE - 2.4L -
INSTALLATION........................7-35
WATER PUMP INLET TUBE - 2.4L -
REMOVAL...........................7-35
WATER PUMP INLET TUBE - 3.3/3.8L -
INSTALLATION........................7-36
WATER PUMP INLET TUBE - 3.3/3.8L -
REMOVAL...........................7-36
WATERSHIELD - INSTALLATION.........23-21
WATERSHIELD - REMOVAL.............23-21
WEAR - STANDARD PROCEDURE,
MEASURING TIMING CHAIN............9-153
WEAR INDICATORS - DIAGNOSIS AND
TESTING, TREAD................22-16,22s-8
WEAR PATTERNS - DIAGNOSIS AND
TESTING, TIRE..................22-16,22s-8
WEATHERSTRIP - INSTALLATION, FRONT
DOOR............................23-114
WEATHERSTRIP - INSTALLATION, FRONT
DOOR GLASS RUN..................23-113
WEATHERSTRIP - INSTALLATION,
SLIDING DOOR.....................23-115
WEATHERSTRIP - REMOVAL, FRONT
DOOR............................23-114
WEATHERSTRIP - REMOVAL, FRONT
DOOR GLASS RUN..................23-113
WEATHERSTRIP - REMOVAL, SLIDING
DOOR............................23-115
WELD LOCATIONS - SPECIFICATIONS . . . 23-166
WHEEL - DESCRIPTION...............22-18
WHEEL - INSPECTION, TONE............5-82
WHEEL - INSTALLATION, STEERING......19-24
WHEEL - REMOVAL, STEERING.........19-23
WHEEL ALIGNMENT - DESCRIPTION......2-47
WHEEL ALIGNMENT - STANDARD
PROCEDURE.........................2-52
WHEEL ALIGNMENT, SPECIFICATIONS.....2-56
WHEEL ASSEMBLY (ALUMINUM WHEEL)
- INSTALLATION, TIRE.................22-8
WHEEL ASSEMBLY (ALUMINUM WHEEL)
- REMOVAL, TIRE.....................22-7
WHEEL ASSEMBLY (STEEL WHEEL) -
INSTALLATION, TIRE...................22-8
WHEEL ASSEMBLY (STEEL WHEEL) -
REMOVAL, TIRE......................22-8
WHEEL BALANCE - STANDARD
PROCEDURE, TIRE....................22-5
WHEEL CARE - CLEANING, ALUMINUM . . . 22-18
WHEEL COVER - DESCRIPTION.........22-19
WHEEL COVER - INSTALLATION.........22-19
WHEEL COVER - REMOVAL............22-19
WHEEL CYLINDERS - INSPECTION . . . 5-57,5s-59
WHEEL CYLINDERS - INSTALLATION . 5-57,5s-60
WHEEL CYLINDERS - REMOVAL.....5-57,5s-59
WHEEL INSPECTION - DIAGNOSIS AND
TESTING...........................22-18
WHEEL MATCH MOUNTING - STANDARD
PROCEDURE, TIRE
....................22-7
WHEEL MOUNTING STUDS - FRONT -
INSTALLATION
.......................22-21
WHEEL MOUNTING STUDS - FRONT -
REMOVAL
..........................22-20
WHEEL MOUNTING STUDS - REAR -
INSTALLATION
.......................22-22
WHEEL MOUNTING STUDS - REAR -
REMOVAL
..........................22-21
WHEEL ROTATION - STANDARD
PROCEDURE, TIRE
....................22-7
WHEEL RUNOUT, SPECIFICATIONS -
TONE
...............................5-79
WHEEL, SPECIFICATIONS
..............22-19
WHEEL SPEED SENSOR - AWD -
INSTALLATION, REAR
..................5-80
WHEEL SPEED SENSOR - AWD -
REMOVAL, REAR
......................5-80
WHEEL SPEED SENSOR - FWD -
INSTALLATION, REAR
..................5-81
WHEEL SPEED SENSOR - FWD -
REMOVAL, REAR
......................5-81
WHEEL SPEED SENSOR -
INSTALLATION, FRONT
.................5-80
38 INDEXRS
Description Group-Page Description Group-Page Description Group-Page