seat memory CHRYSLER VOYAGER 2004 Workshop Manual

(4) Place front door trim panel in position on door.
(5) Install trim panel into inner belt molding at
top of door.
(6) Install clips to attach door trim to door frame
around perimeter of panel.
(7) If equipped, install screw to attach door trim to
door panel behind inside latch release handle.
(8) If equipped, connect power switch into wire
connector.
(9) Place power accessary switch in position on
door trim.
(10) Connect wire connector into memory seat/mir-
ror switch and install switch into trim panel.
(11) Install screws to attach accessary switch
panel to door trim.
(12) Install screw cover into switch panel.
(13) If equipped, install window crank.
(14) If equipped, install screws to attach trim
panel to door inside map pocket.
(15) If equipped, install screw to attach door pull
cup to inner door panel.
(16) If equipped, install screws to attach door
assist handle to inner door panel.
(17) Connect wire connector into courtesy lamp.
(18) Install lamp in door trim.
(19) Install switch bezel.
WATERSHIELD
REMOVAL
(1) Remove door trim panel. (Refer to 23 - BODY/
DOOR - FRONT/TRIM PANEL - REMOVAL)
(2) Remove the front door speaker. (Refer to 8 -
ELECTRICAL/AUDIO/SPEAKER - REMOVAL)
(3) Peel watershield away from adhesive around
perimeter of inner door panel.
INSTALLATION
(1) Insure that enough adhesive remains to
securely retain the water dam. Replace as necessary.
(2) Place the shield into position and press
securely to adhesive making sure to properly route
wiring and linkages.
(3) Install the front door speaker. (Refer to 8 -
ELECTRICAL/AUDIO/SPEAKER - INSTALLATION)
(4) Install door trim panel. (Refer to 23 - BODY/
DOOR - FRONT/TRIM PANEL - INSTALLATION)
WINDOW CRANK
REMOVAL
(1) Using a window crank removal tool, disengage
clip attaching window crank to regulator shaft (Fig.
13).NOTE: Wrap a shop towel around the window crank
to catch the clip when it springs out.
(2) Pull window crank from regulator shaft.
INSTALLATION
(1) Place the clip on to the window crank handle.
(2) Position window crank to regulator shaft.
(3) Push window crank onto regulator shaft to
engage retaining clip.
EXTERIOR HANDLE
REMOVAL
(1) Roll door glass up.
(2) Remove the watershield as necessary to gain
access to the outside door handle. (Refer to 23 -
BODY/DOOR - FRONT/WATERSHIELD -
REMOVAL)
(3) Through access hole at rear of inner door
panel, disconnect Vehicle Theft Security System
(VTSS) switch connector from door harness, if
equipped.
(4) Disengage push in fasteners attaching VTSS
switch harness to inner door reinforcement bar, if
equipped.
(5) Disengage clip holding door latch linkage to
door latch (Fig. 11).
(6) Remove latch linkage from latch.
(7) Disengage clip holding door lock linkage to
door latch.
(8) Remove lock linkage from latch.
(9) Remove nuts holding outside door handle to
door outer panel.
(10) Remove outside door handle from vehicle.
Fig. 13 WINDOW CRANK - TYPICAL
1 - WINDOW CRANK REMOVAL TOOL
2 - WINDOW CRANK
RSDOOR - FRONT23-21
TRIM PANEL (Continued)

chemical reaction takes place. This means the con-
centration of oxygen will be the same downstream as
upstream. The output voltage of the downstream
O2S copies the voltage of the upstream sensor. The
only difference is a time lag (seen by the PCM)
between the switching of the O2S's.
To monitor the system, the number of lean-to-rich
switches of upstream and downstream O2S's is
counted. The ratio of downstream switches to
upstream switches is used to determine whether the
catalyst is operating properly. An effective catalyst
will have fewer downstream switches than it has
upstream switches i.e., a ratio closer to zero. For a
totally ineffective catalyst, this ratio will be one-to-
one, indicating that no oxidation occurs in the device.
The system must be monitored so that when cata-
lyst efficiency deteriorates and exhaust emissions
increase to over the legal limit, the MIL (Check
Engine lamp) will be illuminated.
NATURAL VACUUM LEAK DETECTION (NVLD) (if equipped)
The Natural Vacuum Leak Detection (NVLD) sys-
tem is the next generation evaporative leak detection
system that will first be used on vehicles equipped
with the Next Generation Controller (NGC). This
new system replaces the leak detection pump as the
method of evaporative system leak detection. This is
to detect a leak equivalent to a 0.0209(0.5 mm) hole.
This system has the capability to detect holes of this
size very dependably.
The basic leak detection theory employed with
NVLD is the9Gas Law9. This is to say that the pres-
sure in a sealed vessel will change if the temperature
of the gas in the vessel changes. The vessel will only
see this effect if it is indeed sealed. Even small leaks
will allow the pressure in the vessel to come to equi-
librium with the ambient pressure. In addition to the
detection of very small leaks, this system has the
capability of detecting medium as well as large evap-
orative system leaks.
The NVLD seals the canister vent during engine off
conditions. If the EVAP system has a leak of less than
the failure threshold, the evaporative system will be
pulled into a vacuum, either due to the cool down
from operating temperature or diurnal ambient tem-
perature cycling. The diurnal effect is considered one
of the primary contributors to the leak determination
by this diagnostic. When the vacuum in the system
exceeds about 19H2O (0.25 KPA), a vacuum switch
closes. The switch closure sends a signal to the NGC.
The NGC, via appropriate logic strategies (described
below), utilizes the switch signal, or lack thereof, to
make a determination of whether a leak is present.
The NVLD device is designed with a normally open
vacuum switch, a normally closed solenoid, and a
seal, which is actuated by both the solenoid and a
diaphragm. The NVLD is located on the atmosphericvent side of the canister. The NVLD assembly may
be mounted on top of the canister outlet, or in-line
between the canister and atmospheric vent filter. The
normally open vacuum switch will close with about 19
H2O (0.25 KPA) vacuum in the evaporative system.
The diaphragm actuates the switch. This is above the
opening point of the fuel inlet check valve in the fill
tube so cap off leaks can be detected. Submerged fill
systems must have recirculation lines that do not
have the in-line normally closed check valve that pro-
tects the system from failed nozzle liquid ingestion,
in order to detect cap off conditions.
The normally closed valve in the NVLD is intended
to maintain the seal on the evaporative system dur-
ing the engine off condition. If vacuum in the evapo-
rative system exceeds 39to 69H2O (0.75 to 1.5 KPA),
the valve will be pulled off the seat, opening the seal.
This will protect the system from excessive vacuum
as well as allowing sufficient purge flow in the event
that the solenoid was to become inoperative.
The solenoid actuates the valve to unseal the can-
ister vent while the engine is running. It also will be
used to close the vent during the medium and large
leak tests and during the purge flow check. This sole-
noid requires initial 1.5 amps of current to pull the
valve open but after 100 ms. will be duty cycled down
to an average of about 150 mA for the remainder of
the drive cycle.
Another feature in the device is a diaphragm that
will open the seal in the NVLD with pressure in the
evaporative system. The device will9blow off9at
about 0.59H2O (0.12 KPA) pressure to permit the
venting of vapors during refueling. An added benefit
to this is that it will also allow the tank to9breathe9
during increasing temperatures, thus limiting the
pressure in the tank to this low level. This is benefi-
cial because the induced vacuum during a subse-
quent declining temperature will achieve the switch
closed (pass threshold) sooner than if the tank had to
decay from a built up pressure.
The device itself has 3 wires: Switch sense, sole-
noid driver and ground. It also includes a resistor to
protect the switch from a short to battery or a short
to ground. The NGC utilizes a high-side driver to
energize and duty-cycle the solenoid.
DESCRIPTION - HIGH AND LOW LIMITS
The PCM compares input signal voltages from each
input device with established high and low limits for
the device. If the input voltage is not within limits
and other criteria are met, the PCM stores a diagnos-
tic trouble code in memory. Other diagnostic trouble
code criteria might include engine RPM limits or
input voltages from other sensors or switches that
must be present before verifying a diagnostic trouble
code condition.
25 - 8 EMISSIONS CONTROLRS
EMISSIONS CONTROL (Continued)

LOWER HINGE - REMOVAL.............23-28
LOWER INSTRUMENT PANEL -
INSTALLATION.......................23-69
LOWER INSTRUMENT PANEL -
REMOVAL..........................23-69
LOWER INTAKE MANIFOLD -
INSTALLATION.......................9-149
LOWER INTAKE MANIFOLD - REMOVAL . . . 9-148
LOWER STEERING COLUMN COVER -
INSTALLATION.......................23-70
LOWER STEERING COLUMN COVER -
REMOVAL..........................23-70
LOWER TRIM - INSTALLATION,
B-PILLAR...........................23-75
LOWER TRIM - REMOVAL, B-PILLAR.....23-74
LUBRICANTS - DESCRIPTION, ENGINE
OIL .................................0-1
LUBRICATION - DESCRIPTION......9-136,9-52
LUBRICATION - OPERATION........9-136,9-52
LUBRICATION - STANDARD PROCEDURE....2-2
LUBRICATION POINTS - DESCRIPTION......0-7
LUBRICATION, SPECIFICATIONS - BODY . . 23-12
LUGGAGE RACK CROSSBAR -
INSTALLATION.......................23-57
LUGGAGE RACK CROSSBAR - REMOVAL . . 23-56
LUGGAGE RACK RISER - INSTALLATION . . 23-56
LUGGAGE RACK RISER - REMOVAL......23-55
LUMBAR SUPPORT - INSTALLATION....23-106
LUMBAR SUPPORT - REMOVAL........23-106
LWB - INSTALLATION, SEAT BELT &
RETRACTOR - SECOND ROW - RIGHT
OUTBOARD WITH REAR HVAC..........8O-16
LWB - REMOVAL, SEAT BELT &
RETRACTOR - SECOND ROW - RIGHT
OUTBOARD WITH REAR HVAC..........8O-16
MACHINING - STANDARD PROCEDURE,
BRAKE ROTOR..................5-53,5s-56
MAIN BEARING FITTING - STANDARD
PROCEDURE........................9-123
MAIN BEARINGS - INSTALLATION,
CRANKSHAFT.......................9-124
MAIN BEARINGS - REMOVAL,
CRANKSHAFT.......................9-124
MANAGER - DESCRIPTION, TASK........25-24
MANAGER - OPERATION, TASK.........25-24
MANIFOLD - CLEANING, EXHAUST........9-61
MANIFOLD - DESCRIPTION, INTAKE . . 9-144,9-58
MANIFOLD - INSPECTION, EXHAUST......9-61
MANIFOLD - INSTALLATION, EXHAUST....9-61
MANIFOLD - INSTALLATION, LOWER
INTAKE ............................9-149
MANIFOLD - INSTALLATION, UPPER
INTAKE ............................9-147
MANIFOLD - LEFT - CLEANING,
EXHAUST...........................9-152
MANIFOLD - LEFT - INSPECTION,
EXHAUST...........................9-152
MANIFOLD - LEFT - INSTALLATION,
EXHAUST...........................9-152
MANIFOLD - LEFT - REMOVAL, EXHAUST . 9-152
MANIFOLD - LOWER - CLEANING,
INTAKE ............................9-148
MANIFOLD - LOWER - INSPECTION,
INTAKE ........................9-148,9-60
MANIFOLD - LOWER - INSTALLATION,
INTAKE .............................9-60
MANIFOLD - LOWER - REMOVAL,
INTAKE .............................9-60
MANIFOLD - REMOVAL, EXHAUST........9-61
MANIFOLD - REMOVAL, LOWER INTAKE . . 9-148
MANIFOLD - REMOVAL, UPPER INTAKE . . . 9-145
MANIFOLD - RIGHT - CLEANING,
EXHAUST...........................9-151
MANIFOLD - RIGHT - INSPECTION,
EXHAUST...........................9-151
MANIFOLD - RIGHT - INSTALLATION,
EXHAUST...........................9-151
MANIFOLD - RIGHT - REMOVAL,
EXHAUST...........................9-150
MANIFOLD - UPPER - INSPECTION,
INTAKE
.............................9-59
MANIFOLD - UPPER - INSTALLATION,
INTAKE
.............................9-59
MANIFOLD - UPPER - REMOVAL, INTAKE
. . 9-58
MANIFOLD LEAKS - DIAGNOSIS AND
TESTING, INTAKE
................9-145,9-58
MANIFOLD STRIPPED THREAD REPAIR -
STANDARD PROCEDURE
...............9-145MANIFOLD VACUUM PORT REPAIR -
STANDARD PROCEDURE, INTAKE........9-145
MANUAL - INSTALLATION, WINDOW
REGULATOR........................23-23
MANUAL - REMOVAL, WINDOW
REGULATOR........................23-22
MANUAL ADJUSTER - INSTALLATION,
FRONT SEAT TRACK..................23-95
MANUAL ADJUSTER - REMOVAL, FRONT
SEAT TRACK........................23-95
MANUAL TEMPERATURE CONTROL
(MTC) - INSTALLATION................24-29
MANUAL TEMPERATURE CONTROL
(MTC) - REMOVAL...................24-29
MANUAL TEMPERATURE CONTROL
SYSTEM - OPERATION...............24-112
MANUAL THREE ZONE - DESCRIPTION....24-2
MANUAL THREE ZONE - OPERATION......24-5
MANUAL TRACK - INSTALLATION,
FRONT SEAT RISER...................23-95
MANUAL TRACK - REMOVAL, FRONT
SEAT RISER.........................23-94
MANUAL TRANSAXLE - ASSEMBLY, T850 . 21-42
MANUAL TRANSAXLE - DESCRIPTION,
T850..............................21-21
MANUAL TRANSAXLE - DISASSEMBLY,
T850..............................21-35
MANUAL TRANSAXLE - INSTALLATION,
T850..............................21-51
MANUAL TRANSAXLE - OPERATION,
T850..............................21-24
MANUAL TRANSAXLE - REMOVAL, T850 . . 21-31
MANUAL TRANSAXLE - SPECIFICATIONS,
T850..............................21-56
MANUFACTURER PLATE - DESCRIPTION . Intro.-11
MAP SENSOR - DESCRIPTION..........14-30
MAP SENSOR - OPERATION............14-30
MASTER CYLINDER - LHD -
INSTALLATION........................6-10
MASTER CYLINDER - LHD - REMOVAL.....6-9
MASTER CYLINDER - RHD -
INSTALLATION.........................6-9
MASTER CYLINDER - RHD - REMOVAL.....6-8
MASTER CYLINDER BLEEDING -
STANDARD PROCEDURE...........5-35,5s-34
MASTER CYLINDER (FLUID RESERVOIR)
- ASSEMBLY....................5-38,5s-37
MASTER CYLINDER (FLUID RESERVOIR)
- DISASSEMBLY.................5-37,5s-36
MATCH MOUNTING - STANDARD
PROCEDURE, TIRE AND WHEEL..........22-7
MATS - INSTALLATION, CARPETS AND
FLOOR.............................23-76
MATS - REMOVAL, CARPETS AND
FLOOR.............................23-75
MEASUREMENT - STANDARD
PROCEDURE, CURB HEIGHT.............2-55
MEASUREMENT AND ADJUSTMENT,
ADJUSTMENTS - DIFFERENTIAL
BEARING PRELOAD.................21s-100
MEASUREMENTS - SPECIFICATIONS,
GAP AND FLUSH
....................23-124
MEASURING BEARING CLEARANCE
USING PLASTIGAGE - STANDARD
PROCEDURE
.....................9-12,9-84
MEASURING CAMSHAFT END PLAY -
STANDARD PROCEDURE
................9-29
MEASURING CONNECTING ROD
BEARING CLEARANCE - STANDARD
PROCEDURE
........................9-120
MEASURING CRANKSHAFT END PLAY -
STANDARD PROCEDURE
...............9-125
MEASURING TIMING CHAIN WEAR -
STANDARD PROCEDURE
...............9-153
MECHANICAL - DIAGNOSIS AND
TESTING, ENGINE DIAGNOSIS
........9-6,9-80
MECHANISM - INSTALLATION,
GEARSHIFT
.........................21-89
MECHANISM - REMOVAL, GEARSHIFT
....21-87
MEMORIES, OPERATION - FUEL
CORRECTION OR ADAPTIVE
............14-20
MEMORY SEAT/MIRROR MODULE -
DESCRIPTION
.......................8E-10
MEMORY SEAT/MIRROR MODULE -
DIAGNOSIS AND TESTING
.............8E-10
MEMORY SEAT/MIRROR MODULE -
INSTALLATION
.......................8E-10MEMORY SEAT/MIRROR MODULE -
OPERATION.........................8E-10
MEMORY SEAT/MIRROR MODULE -
REMOVAL..........................8E-10
MEMORY SET SWITCH - DESCRIPTION . . 8N-12,
8N-55
MEMORY SET SWITCH - INSTALLATION . . 8N-13,
8N-56
MEMORY SET SWITCH - OPERATION....8N-13,
8N-56
MEMORY SET SWITCH - REMOVAL . 8N-13,8N-56
MEMORY SWITCH - DIAGNOSIS AND
TESTING......................8N-13,8N-56
MEMORY SYSTEM - DESCRIPTION . . 8N-51,8N-8
MEMORY SYSTEM - DIAGNOSIS AND
TESTING......................8N-10,8N-53
MEMORY SYSTEM - OPERATION....8N-52,8N-9
METRIC SYSTEM - DESCRIPTION......Intro.-6
MINI-TRIP COMPUTER - DIAGNOSIS
AND TESTING, COMPASS.............8M-10
MIRROR - DESCRIPTION, AUTOMATIC
DAY / NIGHT........................8N-47
MIRROR - DIAGNOSIS AND TESTING,
AUTOMATIC DAY / NIGHT..............8N-47
MIRROR - INSTALLATION, REAR VIEW . . . 23-81
MIRROR - INSTALLATION, SIDE VIEW....23-59
MIRROR - OPERATION, AUTOMATIC DAY
/ NIGHT............................8N-47
MIRROR - REMOVAL, REAR VIEW.......23-81
MIRROR - REMOVAL, SIDE VIEW........23-59
MIRROR - REMOVAL, SIDEVIEW..........8N-49
MIRROR GLASS - INSTALLATION, SIDE
VIEW..............................23-59
MIRROR GLASS - REMOVAL, SIDE VIEW . . 23-59
MIRROR SWITCH - EXPORT -
DESCRIPTION, POWER FOLDAWAY......8N-48
MIRROR SWITCH - EXPORT -
INSTALLATION, POWER FOLDAWAY......8N-49
MIRROR SWITCH - EXPORT -
OPERATION, POWER FOLDAWAY........8N-48
MIRROR SWITCH - EXPORT - REMOVAL,
POWER FOLDAWAY..................8N-48
MIRRORS - DESCRIPTION, HEATED.......8G-6
MIRRORS - DESCRIPTION, POWER......8N-45
MIRRORS - DIAGNOSIS AND TESTING,
POWER............................8N-46
MIRRORS - OPERATION, HEATED........8G-6
MIRRORS - OPERATION, POWER........8N-45
MISALIGNMENT - DIAGNOSIS AND
TESTING, DRIVE PLATE.................6-6
MODE DOOR ACTUATOR - DESCRIPTION . . 24-30
MODE DOOR ACTUATOR -
INSTALLATION.......................24-31
MODE DOOR ACTUATOR - OPERATION . . . 24-30
MODE DOOR ACTUATOR - REAR -
DESCRIPTION.......................24-39
MODE DOOR ACTUATOR - REAR -
INSTALLATION.......................24-40
MODE DOOR ACTUATOR - REAR -
OPERATION.........................24-40
MODE DOOR ACTUATOR - REAR -
REMOVAL..........................24-40
MODE DOOR ACTUATOR - REMOVAL.....24-30
MODE, OPERATION - DRB IIITS TAT E
DISPLAY TEST........................25-9
MODES OF OPERATION - OPERATION....14-18
MODULAR CLUTCH ASSY - 2.4L GAS -
INSTALLATION........................6-11
MODULAR CLUTCH ASSY - 2.4L GAS -
REMOVAL...........................6-11
MODULE - BLOWER MOTOR -
DESCRIPTION, POWER................24-31
MODULE - BLOWER MOTOR -
INSTALLATION, POWER...............24-32
MODULE - BLOWER MOTOR -
OPERATION, POWER..................24-31
MODULE - BLOWER MOTOR -
REMOVAL, POWER...................24-31
MODULE - DESCRIPTION, BODY
CONTROL............................8s-1
MODULE - DESCRIPTION, BODY
CONTROL
...........................8E-3
MODULE - DESCRIPTION, FRONT
CONTROL
...........................8E-7
MODULE - DESCRIPTION, FUEL PUMP
....14-8
MODULE - DESCRIPTION, HEATED SEAT
. . . 8E-8
MODULE - DESCRIPTION, INTEGRATED
POWER
..........................8W-97-2
RSINDEX21
Description Group-Page Description Group-Page Description Group-Page

MODULE - DESCRIPTION, MEMORY
SEAT/MIRROR.......................8E-10
MODULE - DESCRIPTION, POWER
LIFTGATE CONTROL..................8E-10
MODULE - DESCRIPTION, REAR
DRIVELINE...........................3-23
MODULE - DESCRIPTION, REMOTE
KEYLESS ENTRY.....................8N-43
MODULE - DESCRIPTION, SENTRY KEY
IMMOBILIZER.......................8E-18
MODULE - DESCRIPTION, SENTRY KEY
REMOTE ENTRY......................8Q-3
MODULE - DESCRIPTION, SLIDING
DOOR CONTROL.....................8E-19
MODULE - DESCRIPTION,
TRANSMISSION CONTROL.............8E-20
MODULE - DIAGNOSIS AND TESTING,
FRONT CONTROL.....................8E-7
MODULE - DIAGNOSIS AND TESTING,
HEATED SEAT ........................8E-9
MODULE - DIAGNOSIS AND TESTING,
MEMORY SEAT/MIRROR...............8E-10
MODULE - DIAGNOSIS AND TESTING,
REMOTE KEYLESS ENTRY.............8N-43
MODULE - DIAGNOSIS AND TESTING,
SENTRY KEY REMOTE ENTRY...........8Q-5
MODULE - EXPORT - DESCRIPTION,
ANTENNA...........................8A-6
MODULE - EXPORT - DIAGNOSIS AND
TESTING, ANTENNA...................8A-7
MODULE - EXPORT - INSTALLATION,
ANTENNA...........................8A-7
MODULE - EXPORT - OPERATION,
ANTENNA.............................8A-6
MODULE - EXPORT - REMOVAL,
ANTENNA...........................8A-7
MODULE - INSTALLATION, BODY
CONTROL............................8s-3
MODULE - INSTALLATION, BODY
CONTROL...........................8E-5
MODULE - INSTALLATION, FRONT
CONTROL...........................8E-8
MODULE - INSTALLATION, FUEL PUMP....14-9
MODULE - INSTALLATION, HEATED SEAT . . 8E-10
MODULE - INSTALLATION, INTEGRATED
POWER..........................8W-97-3
MODULE - INSTALLATION, MEMORY
SEAT/MIRROR.......................8E-10
MODULE - INSTALLATION, POWER
LIFTGATE CONTROL..................8E-11
MODULE - INSTALLATION, REMOTE
KEYLESS ENTRY.....................8N-44
MODULE - INSTALLATION, SENTRY KEY
IMMOBILIZER.......................8E-19
MODULE - INSTALLATION, SENTRY KEY
REMOTE ENTRY......................8Q-6
MODULE - INSTALLATION, SLIDING
DOOR CONTROL.....................8E-20
MODULE - INSTALLATION, WIPER.......8R-15
MODULE - OPERATION, BODY CONTROL . . . 8s-1
MODULE - OPERATION, BODY CONTROL . . . 8E-3
MODULE - OPERATION, FRONT
CONTROL...........................8E-7
MODULE - OPERATION, FUEL PUMP
......14-8
MODULE - OPERATION, HEATED SEAT
.....8E-9
MODULE - OPERATION, INTEGRATED
POWER
..........................8W-97-2
MODULE - OPERATION, MEMORY
SEAT/MIRROR
.......................8E-10
MODULE - OPERATION, POWER
LIFTGATE CONTROL
..................8E-11
MODULE - OPERATION, REAR
DRIVELINE
...........................3-23
MODULE - OPERATION, REMOTE
KEYLESS ENTRY
.....................8N-43
MODULE - OPERATION, SENTRY KEY
IMMOBILIZER
.......................8E-18
MODULE - OPERATION, SENTRY KEY
REMOTE ENTRY
......................8Q-4
MODULE - OPERATION, SLIDING DOOR
CONTROL
..........................8E-19
MODULE - OPERATION, TRANSMISSION
CONTROL
..........................8E-20
MODULE - REAR BLOWER MOTOR -
DESCRIPTION, POWER
................24-41
MODULE - REAR BLOWER MOTOR -
INSTALLATION, POWER
...............24-42MODULE - REAR BLOWER MOTOR -
OPERATION, POWER..................24-41
MODULE - REAR BLOWER MOTOR -
REMOVAL, POWER...................24-41
MODULE - REMOVAL, BODY CONTROL....8s-3
MODULE - REMOVAL, BODY CONTROL....8E-4
MODULE - REMOVAL, FRONT CONTROL . . . 8E-8
MODULE - REMOVAL, FUEL PUMP........14-8
MODULE - REMOVAL, HEATED SEAT......8E-9
MODULE - REMOVAL, INTEGRATED
POWER..........................8W-97-2
MODULE - REMOVAL, MEMORY
SEAT/MIRROR.......................8E-10
MODULE - REMOVAL, POWER LIFTGATE
CONTROL..........................8E-11
MODULE - REMOVAL, REMOTE KEYLESS
ENTRY.............................8N-44
MODULE - REMOVAL, SENTRY KEY
IMMOBILIZER.......................8E-18
MODULE - REMOVAL, SENTRY KEY
REMOTE ENTRY......................8Q-5
MODULE - REMOVAL, SLIDING DOOR
CONTROL..........................8E-19
MODULE - REMOVAL, WIPER...........8R-15
MODULE - SPECIFICATIONS, REAR
DRIVELINE...........................3-34
MODULE, BENCH SEAT - REMOVAL,
CHILD SEAT.........................23-87
MODULE FLUIDS - DESCRIPTION, AWD
REAR DRIVELINE......................0-6
MODULE LAMP REPLACEMENT -
STANDARD PROCEDURE.................8M-3
MODULE NOISE - DIAGNOSIS AND
TESTING, REAR DRIVELINE.............3-24
MODULE OPERATION - DIAGNOSIS AND
TESTING, REAR DRIVELINE.............3-26
MOLDING - INSTALLATION, FRONT
DOOR INNER BELT..................23-115
MOLDING - INSTALLATION, FRONT
DOOR OUTER BELT..................23-113
MOLDING - INSTALLATION, ROOF JOINT . . 23-58
MOLDING - REMOVAL, FRONT DOOR
INNER BELT........................23-115
MOLDING - REMOVAL, FRONT DOOR
OUTER BELT.......................23-113
MOLDING - REMOVAL, ROOF JOINT......23-58
MOLDINGS - INSTALLATION, BODY SIDE . . 23-46
MOLDINGS - REMOVAL, BODY SIDE.....23-45
MONITORED COMPONENT -
DESCRIPTION........................25-1
MONITORED SYSTEMS - DESCRIPTION....25-6
MONITORING - DESCRIPTION, TIRE
PRESSURE.....................22-9,22s-1
MONITORING - OPERATION, TIRE
PRESSURE.....................22-9,22s-1
MOTOR - DESCRIPTION, BLOWER . . 24-46,24-57
MOTOR - DESCRIPTION, IDLE AIR
CONTROL..........................14-28
MOTOR - DESCRIPTION, LIFTGATE......8N-15
MOTOR - DESCRIPTION, POWER
MODULE - BLOWER..................24-31
MOTOR - DESCRIPTION, POWER
MODULE - REAR BLOWER.............24-41
MOTOR - DESCRIPTION, SLIDING DOOR . . 8N-30
MOTOR - DIAGNOSIS AND TESTING,
BLOWER...........................24-47
MOTOR - DIAGNOSIS AND TESTING,
DOOR LOCK....................8N-4,8N-41
MOTOR - DIAGNOSIS AND TESTING,
RADIATOR FAN.......................7-29
MOTOR - DIAGNOSIS AND TESTING,
REAR BLOWER......................24-58
MOTOR - DIAGNOSIS AND TESTING,
VENT WINDOW......................8N-63
MOTOR - INSTALLATION, BLOWER . 24-49,24-58
MOTOR - INSTALLATION, FRONT
WASHER PUMP......................8R-8
MOTOR - INSTALLATION, FRONT WIPER . . . 8R-9
MOTOR - INSTALLATION, IDLE AIR
CONTROL..........................14-29
MOTOR - INSTALLATION, LIFTGATE
......8N-15
MOTOR - INSTALLATION, POWER
MODULE - BLOWER
..................24-32
MOTOR - INSTALLATION, POWER
MODULE - REAR BLOWER
.............24-42
MOTOR - INSTALLATION, REAR WASHER
PUMP
.............................8R-10
MOTOR - INSTALLATION, REAR WIPER
. . . 8R-11MOTOR - INSTALLATION, SLIDING DOOR . 8N-31
MOTOR - INSTALLATION, SLIDING DOOR
LOCK.........................8N-44,8N-6
MOTOR - INSTALLATION, SUNROOF.....23-121
MOTOR - INSTALLATION, VENT WINDOW . 8N-64
MOTOR - OPERATION, BLOWER....24-46,24-57
MOTOR - OPERATION, IDLE AIR
CONTROL..........................14-28
MOTOR - OPERATION, LIFTGATE........8N-15
MOTOR - OPERATION, POWER MODULE
- BLOWER..........................24-31
MOTOR - OPERATION, POWER MODULE
- REAR BLOWER.....................24-41
MOTOR - OPERATION, SLIDING DOOR . . . 8N-30
MOTOR - REMOVAL, BLOWER.....24-47,24-58
MOTOR - REMOVAL, FRONT WASHER
PUMP..............................8R-8
MOTOR - REMOVAL, FRONT WIPER......8R-9
MOTOR - REMOVAL, IDLE AIR CONTROL . . 14-29
MOTOR - REMOVAL, LIFTGATE.........8N-15
MOTOR - REMOVAL, POWER MODULE -
BLOWER...........................24-31
MOTOR - REMOVAL, POWER MODULE -
REAR BLOWER......................24-41
MOTOR - REMOVAL, REAR WASHER
PUMP.............................8R-10
MOTOR - REMOVAL, REAR WIPER......8R-11
MOTOR - REMOVAL, SLIDING DOOR.....8N-30
MOTOR - REMOVAL, SLIDING DOOR
LOCK...........................8N-44,8N-6
MOTOR - REMOVAL, SUNROOF........23-121
MOTOR - REMOVAL, VENT WINDOW.....8N-63
MOTOR - REMOVAL, WINDOW..........8N-64
MOTOR RELAY - DESCRIPTION,
BLOWER......................24-24,24-37
MOTOR RELAY - INSTALLATION,
BLOWER......................24-25,24-38
MOTOR RELAY - OPERATION, BLOWER . . 24-24,
24-37
MOTOR RELAY - REMOVAL, BLOWER....24-25,
24-38
MOTOR RESISTOR - DESCRIPTION,
BLOWER...........................24-38
MOTOR RESISTOR - INSTALLATION,
BLOWER...........................24-39
MOTOR RESISTOR - OPERATION,
BLOWER...........................24-38
MOTOR RESISTOR - REMOVAL,
BLOWER...........................24-39
MOTOR RESISTOR BLOCK -
DESCRIPTION, BLOWER...............24-26
MOTOR RESISTOR BLOCK - DIAGNOSIS
AND TESTING, BLOWER...............24-26
MOTOR RESISTOR BLOCK - DIAGNOSIS
AND TESTING, REAR BLOWER..........24-38
MOTOR RESISTOR BLOCK -
INSTALLATION, BLOWER..............24-27
MOTOR RESISTOR BLOCK - OPERATION,
BLOWER...........................24-26
MOTOR RESISTOR BLOCK - REMOVAL,
BLOWER...........................24-26
MOUNT - INSTALLATION, FRONT....9-131,9-49
MOUNT - INSTALLATION, LEFT......9-133,9-50
MOUNT - INSTALLATION, REAR.....9-134,9-50
MOUNT - INSTALLATION, RIGHT....9-135,9-51
MOUNT - REMOVAL, FRONT........9-131,9-49
MOUNT - REMOVAL, LEFT.........9-133,9-49
MOUNT - REMOVAL, REAR.........9-133,9-50
MOUNT - REMOVAL, RIGHT........9-135,9-51
MOUNT BUSHINGS - INSTALLATION,
FRONT CROSSMEMBER...............13-12
MOUNT BUSHINGS - REMOVAL, FRONT
CROSSMEMBER.....................13-12
MOUNTED STOP LAMP - INSTALLATION,
CENTER HIGH........................8L-6
MOUNTED STOP LAMP - REMOVAL,
CENTER HIGH........................8L-6
MOUNTED STOP LAMP UNIT -
INSTALLATION, CENTER HIGH...........8L-6
MOUNTED STOP LAMP UNIT -
REMOVAL, CENTER HIGH
...............8L-6
MOUNTING - DESCRIPTION, ENGINE
. 9-131,9-48
MOUNTING - STANDARD PROCEDURE,
TIRE AND WHEEL MATCH
...............22-7
MOUNTING BRACKET - 2.4L ENGINE -
INSTALLATION, A/C COMPRESSOR
.......24-76
MOUNTING BRACKET - 2.4L ENGINE -
REMOVAL, A/C COMPRESSOR
..........24-75
22 INDEXRS
Description Group-Page Description Group-Page Description Group-Page

SEAT TRACK MANUAL ADJUSTER -
INSTALLATION, FRONT................23-95
SEAT TRACK MANUAL ADJUSTER -
REMOVAL, FRONT....................23-95
SEAT TRACK POWER ADJUSTER -
INSTALLATION, FRONT................23-95
SEAT TRACK POWER ADJUSTER -
REMOVAL, FRONT....................23-95
SEATBACK ASSIST STRAP -
INSTALLATION, FRONT................23-92
SEATBACK ASSIST STRAP - REMOVAL,
FRONT.............................23-92
SEATBACK COVER - INSTALLATION,
FRONT.............................23-93
SEATBACK COVER - REMOVAL, FRONT . . . 23-93
SEATBACK PANEL - INSTALLATION,
BENCH.............................23-99
SEATBACK PANEL - INSTALLATION,
FRONT.............................23-93
SEATBACK PANEL - REMOVAL, BENCH . . . 23-99
SEATBACK PANEL - REMOVAL, FRONT....23-92
SEAT/MIRROR MODULE - DESCRIPTION,
MEMORY...........................8E-10
SEAT/MIRROR MODULE - DIAGNOSIS
AND TESTING, MEMORY...............8E-10
SEAT/MIRROR MODULE -
INSTALLATION, MEMORY..............8E-10
SEAT/MIRROR MODULE - OPERATION,
MEMORY...........................8E-10
SEAT/MIRROR MODULE - REMOVAL,
MEMORY...........................8E-10
SEATS - CLEANING, INTAKE/EXHAUST
VALVES.....................9-105,9-32,9s-22
SEATS - DESCRIPTION, INTAKE/
EXHAUST VALVES...........9-104,9-32,9s-21
SEATS - INSPECTION, INTAKE/EXHAUST
VALVES .......................9-105,9s-22
SEATS - INSTALLATION, INTAKE/
EXHAUST VALVES...............9-106,9s-23
SEATS - OPERATION, INTAKE/EXHAUST
VALVES .......................9-104,9s-21
SEATS - REMOVAL, INTAKE/EXHAUST
VALVES .......................9-105,9s-22
SEATS - STANDARD PROCEDURE,
REFACING VALVES AND VALVE.....9-104,9s-21
SECOND ROW - INSTALLATION, BENCH
SEAT RISER........................23-101
SECOND ROW - LEFT OUTBOARD -
INSTALLATION, SEAT BELT &
RETRACTOR........................8O-17
SECOND ROW - LEFT OUTBOARD -
REMOVAL, SEAT BELT & RETRACTOR....8O-17
SECOND ROW - REMOVAL, BENCH SEAT
RISER............................23-101
SECOND ROW - RIGHT OUTBOARD -
INSTALLATION, SEAT BELT &
RETRACTOR........................8O-15
SECOND ROW - RIGHT OUTBOARD -
REMOVAL, SEAT BELT & RETRACTOR
....8O-15
SECOND ROW - RIGHT OUTBOARD
WITH REAR HVAC - LWB -
INSTALLATION, SEAT BELT &
RETRACTOR
........................8O-16
SECOND ROW - RIGHT OUTBOARD
WITH REAR HVAC - LWB - REMOVAL,
SEAT BELT & RETRACTOR
.............8O-16
SECOND ROW - THREE PASSENGER
BENCH - INSTALLATION, SEAT BELT
BUCKLE
............................8O-15
SECOND ROW - THREE PASSENGER
BENCH - REMOVAL, SEAT BELT
BUCKLE
............................8O-15
SECOND ROW INBOARD - 50/50 BENCH
- INSTALLATION, SEAT BELT BUCKLE
....8O-13
SECOND ROW INBOARD - 50/50 BENCH
- REMOVAL, SEAT BELT BUCKLE
........8O-13
SECTION IDENTIFICATION AND
INFORMATION - DESCRIPTION
........8W-01-6
SECURITY - DESCRIPTION, VEHICLE
THEFT
..............................8Q-1
SECURITY - OPERATION, VEHICLE THEFT
. . 8Q-1
SECURITY SYSTEM - DIAGNOSIS AND
TESTING, VEHICLE THEFT
..............8Q-3
SELECTION, ADJUSTMENTS - OUTPUT
FLANGE SHIM
........................21-7
SELECTOR - INSTALLATION, GEARSHIFT
CABLE
.............................21-84SELECTOR - REMOVAL, GEARSHIFT
CABLE.............................21-81
SELF-DIAGNOSTICS - DIAGNOSIS AND
TESTING............................8J-2
SENDING UNIT / SENSOR -
DESCRIPTION, FUEL LEVEL.............14-5
SENDING UNIT / SENSOR -
INSTALLATION, FUEL LEVEL.............14-5
SENDING UNIT / SENSOR - OPERATION,
FUEL LEVEL..........................14-5
SENDING UNIT / SENSOR - REMOVAL,
FUEL LEVEL..........................14-5
SENSE - PCM INPUT - OPERATION,
IGNITION...........................8E-15
SENSITIVE DEVICES - STANDARD
PROCEDURE, ELECTROSTATIC
DISCHARGE (ESD).................8W-01-8
SENSOR - 2.4L - DESCRIPTION, ENGINE
COOLANT TEMPERATURE...............7-21
SENSOR - 2.4L - INSTALLATION, ENGINE
COOLANT TEMPERATURE...............7-21
SENSOR - 2.4L - REMOVAL, ENGINE
COOLANT TEMPERATURE...............7-21
SENSOR - 3.3/3.8L - DESCRIPTION,
ENGINE COOLANT TEMPERATURE........7-21
SENSOR - 3.3/3.8L - INSTALLATION,
ENGINE COOLANT TEMPERATURE........7-22
SENSOR - 3.3/3.8L - REMOVAL, ENGINE
COOLANT TEMPERATURE...............7-21
SENSOR - AWD - INSTALLATION, REAR
WHEEL SPEED........................5-80
SENSOR - AWD - REMOVAL, REAR
WHEEL SPEED........................5-80
SENSOR - DESCRIPTION, AMBIENT
TEMP.............................8M-11
SENSOR - DESCRIPTION, BATTERY
TEMPERATURE......................8F-23
SENSOR - DESCRIPTION, CAMSHAFT
POSITION............................8I-4
SENSOR - DESCRIPTION, CRANKSHAFT
POSITION..........................14-25
SENSOR - DESCRIPTION, ENGINE SPEED . 14-26
SENSOR - DESCRIPTION, EVAPORATOR
TEMPERATURE......................24-27
SENSOR - DESCRIPTION, FUEL LEVEL
SENDING UNIT.......................14-5
SENSOR - DESCRIPTION, HEATED SEAT . . 8G-12
SENSOR - DESCRIPTION, INFRARED
TEMPERATURE......................24-29
SENSOR - DESCRIPTION, INLET AIR
TEMPERATURE......................14-30
SENSOR - DESCRIPTION, KNOCK.........8I-8
SENSOR - DESCRIPTION, MAP..........14-30
SENSOR - DESCRIPTION, O2...........14-32
SENSOR - DESCRIPTION, PINCH........8N-17
SENSOR - DESCRIPTION, THROTTLE
POSITION..........................14-36
SENSOR - DESCRIPTION,
TRANSMISSION RANGE.......21-248,21s-150
SENSOR - DIAGNOSIS AND TESTING,
AMBIENT TEMPERATURE..............8M-12
SENSOR - DIAGNOSIS AND TESTING,
HEATED SEAT .......................8G-12
SENSOR - DIAGNOSIS AND TESTING,
TIRE PRESSURE
................22-10,22s-2
SENSOR - FWD - INSTALLATION, REAR
WHEEL SPEED
........................5-81
SENSOR - FWD - REMOVAL, REAR
WHEEL SPEED
........................5-81
SENSOR - INPUT - DESCRIPTION,
SPEED
.....................21-239,21s-140
SENSOR - INPUT - INSTALLATION,
SPEED
.....................21-240,21s-141
SENSOR - INPUT - OPERATION, SPEED
. 21-240,
21s-140
SENSOR - INPUT - REMOVAL, SPEED
. . . 21-240,
21s-141
SENSOR - INSTALLATION, FRONT
WHEEL SPEED
........................5-80
SENSOR - INSTALLATION, FUEL LEVEL
SENDING UNIT
.......................14-5
SENSOR - INSTALLATION, PINCH
........8N-17
SENSOR - INSTALLATION,
TRANSMISSION RANGE
.......21-249,21s-152
SENSOR - INSTALLATION, VEHICLE
SPEED
............................21-115
SENSOR - OPERATION, AMBIENT TEMP
. . 8M-11SENSOR - OPERATION, BATTERY
TEMPERATURE......................8F-23
SENSOR - OPERATION, CAMSHAFT
POSITION............................8I-4
SENSOR - OPERATION, CRANKSHAFT
POSITION..........................14-25
SENSOR - OPERATION, ENGINE SPEED . . . 14-26
SENSOR - OPERATION, EVAPORATOR
TEMPERATURE......................24-28
SENSOR - OPERATION, FUEL LEVEL
SENDING UNIT.......................14-5
SENSOR - OPERATION, HEATED SEAT....8G-12
SENSOR - OPERATION, INFRARED
TEMPERATURE......................24-29
SENSOR - OPERATION, KNOCK...........8I-8
SENSOR - OPERATION, MAP...........14-30
SENSOR - OPERATION, O2.............14-32
SENSOR - OPERATION, PINCH..........8N-17
SENSOR - OPERATION, THROTTLE
POSITION..........................14-36
SENSOR - OPERATION, TRANSMISSION
RANGE.....................21-248,21s-151
SENSOR - OUTPUT - DESCRIPTION,
SPEED.....................21-241,21s-142
SENSOR - OUTPUT - INSTALLATION,
SPEED.....................21-242,21s-143
SENSOR - OUTPUT - OPERATION,
SPEED.....................21-241,21s-142
SENSOR - OUTPUT - REMOVAL, SPEED . 21-241,
21s-143
SENSOR - REMOVAL, BATTERY
TEMPERATURE........................8F-23
SENSOR - REMOVAL, CRANKSHAFT
POSITION..........................14-25
SENSOR - REMOVAL, FRONT WHEEL
SPEED..............................5-79
SENSOR - REMOVAL, FUEL LEVEL
SENDING UNIT.......................14-5
SENSOR - REMOVAL, PINCH...........8N-17
SENSOR - REMOVAL, TRANSMISSION
RANGE.....................21-249,21s-151
SENSOR - REMOVAL, VEHICLE SPEED . . . 21-115
SENSOR - SPECIFICATIONS, BATTERY
TEMPERATURE......................8F-22
SENSOR - TPM - CAUTION........22-10,22s-2
SENSOR - TPM - DESCRIPTION....22-10,22s-1
SENSOR - TPM - INSTALLATION....22-12,22s-3
SENSOR - TPM - OPERATION......22-10,22s-2
SENSOR - TPM - REMOVAL.......22-11,22s-2
SENSOR AIR GAP, SPECIFICATIONS -
WHEEL SPEED........................5-79
SENSOR CIRCUIT - DIAGNOSIS AND
TESTING, AMBIENT TEMPERATURE......8M-12
SENSOR RETRAIN - STANDARD
PROCEDURE, TIRE PRESSURE.....22-10,22s-2
SENSOR RETURN - PCM INPUT -
OPERATION.........................8E-15
SENTRY KEY IMMOBILIZER MODULE -
DESCRIPTION.......................8E-18
SENTRY KEY IMMOBILIZER MODULE -
INSTALLATION.......................8E-19
SENTRY KEY IMMOBILIZER MODULE -
OPERATION.........................8E-18
SENTRY KEY IMMOBILIZER MODULE -
REMOVAL..........................8E-18
SENTRY KEY REMOTE ENTRY MODULE -
DESCRIPTION
........................8Q-3
SENTRY KEY REMOTE ENTRY MODULE -
DIAGNOSIS AND TESTING
..............8Q-5
SENTRY KEY REMOTE ENTRY MODULE -
INSTALLATION
.......................8Q-6
SENTRY KEY REMOTE ENTRY MODULE -
OPERATION
..........................8Q-4
SENTRY KEY REMOTE ENTRY MODULE -
REMOVAL
...........................8Q-5
SENTRY KEY REMOTE ENTRY SYSTEM -
DIAGNOSIS AND TESTING
..............8Q-3
SERVO - DESCRIPTION
.................8P-4
SERVO - INSTALLATION
................8P-5
SERVO - OPERATION
..................8P-4
SERVO - REMOVAL
....................8P-5
SET SWITCH - DESCRIPTION,
MEMORY
.....................8N-12,8N-55
SET SWITCH - INSTALLATION,
MEMORY
.....................8N-13,8N-56
SET SWITCH - OPERATION,
MEMORY
.....................8N-13,8N-56
RSINDEX31
Description Group-Page Description Group-Page Description Group-Page

SET SWITCH - REMOVAL, MEMORY.....8N-13,
8N-56
SETTING - STANDARD PROCEDURE,
PINION FACTOR................8E-15,8E-23
SETTING TRANSMITTER CODES -
STANDARD PROCEDURE..............8M-11
SEVERAL LOADS - STANDARD
PROCEDURE, TESTING FOR A SHORT
TO GROUND ON FUSES POWERING . . . 8W-01-10
SHAFT - ASSEMBLY, INPUT........21-96,21s-5
SHAFT - ASSEMBLY, INTERMEDIATE....21-107,
21s-17
SHAFT - ASSEMBLY, ROCKER ARMS.....9-109,
9s-27
SHAFT - DESCRIPTION, INPUT.....21-93,21s-1
SHAFT - DESCRIPTION, INTERMEDIATE . 21-100,
21s-9
SHAFT - DESCRIPTION, PROPELLER......3-21
SHAFT - DESCRIPTION, SHIFT FORK....21-113
SHAFT - DIAGNOSIS AND TESTING,
HALF............................3-1,3-13
SHAFT - DISASSEMBLY, INPUT.....21-93,21s-1
SHAFT - DISASSEMBLY, INTERMEDIATE . 21-100,
21s-10
SHAFT - DISASSEMBLY, ROCKER ARMS . . 9-109,
9s-27
SHAFT - FRONT - DESCRIPTION, HALF.....3-1
SHAFT - FRONT - INSTALLATION, HALF.....3-4
SHAFT - FRONT - REMOVAL, HALF........3-2
SHAFT - FRONT - SPECIFICATIONS, HALF . . 3-15,
3-6
SHAFT - INSTALLATION, PROPELLER......3-22
SHAFT - INSTALLATION, ROCKER ARMS . . 9-110,
9s-28
SHAFT - OPERATION, PROPELLER........3-21
SHAFT - REAR - DESCRIPTION, HALF.....3-13
SHAFT - REAR - INSTALLATION, HALF.....3-14
SHAFT - REAR - REMOVAL, HALF........3-13
SHAFT - REMOVAL, PROPELLER.........3-21
SHAFT - REMOVAL, ROCKER ARMS . 9-109,9s-27
SHAFT - RHD - INSTALLATION, PEDAL
TORQUE........................5-39,5s-43
SHAFT - RHD - REMOVAL, PEDAL
TORQUE........................5-39,5s-42
SHAFT - SPECIFICATIONS, PROPELLER....3-22
SHAFT COVER SEAL - INSTALLATION,
INPUT.............................21-14
SHAFT COVER SEAL - REMOVAL, INPUT . . 21-13
SHAFT END SEAL - INSTALLATION,
INPUT.............................21-16
SHAFT END SEAL - REMOVAL, INPUT....21-15
SHAFT INNER SEAL - INSTALLATION,
HALF..............................21-12
SHAFT INNER SEAL - REMOVAL, HALF . . . 21-12
SHAFT SEAL - INSTALLATION, INPUT.....21-18
SHAFT SEAL - INSTALLATION, OUTER
HALF..............................21-19
SHAFT SEAL - REMOVAL, INPUT........21-17
SHAFT SEAL - REMOVAL, OUTER HALF . . . 21-19
SHAFTS AND CARRIER ASSEMBLY -
DESCRIPTION, BALANCE................9-69
SHAFTS AND CARRIER ASSEMBLY -
INSTALLATION, BALANCE...............9-72
SHAFTS AND CARRIER ASSEMBLY -
OPERATION, BALANCE.................9-69
SHAFTS AND CARRIER ASSEMBLY -
REMOVAL, BALANCE...................9-69
SHIELD - INSTALLATION, FRONT
WHEELHOUSE SPLASH................23-55
SHIELD - NO CUPHOLDER -
INSTALLATION, QUAD BUCKET SEAT
SIDE..............................23-97
SHIELD - NO CUPHOLDER - REMOVAL,
QUAD BUCKET SEAT SIDE.............23-97
SHIELD - REMOVAL, FRONT
WHEELHOUSE SPLASH................23-55
SHIELD/CUPHOLDER - FLAP AND
SPRING ASSEMBLY - INSTALLATION,
QUAD BUCKET SEAT SIDE............23-107
SHIELD/CUPHOLDER - FLAP AND
SPRING ASSEMBLY - REMOVAL, QUAD
BUCKET SEAT SIDE
..................23-107
SHIELD/CUPHOLDER - INSTALLATION,
QUAD BUCKET SEAT SIDE
.............23-96
SHIELD/CUPHOLDER - REMOVAL, QUAD
BUCKET SEAT SIDE
...................23-96
SHIELDS - DESCRIPTION, HEAT
..........11-6
SHIELDS - INSTALLATION, HEAT
.........11-7SHIELDS - OPERATION, HEAT............11-7
SHIELDS - REMOVAL, HEAT.............11-7
SHIFT CABLE - INSTALLATION, GEAR....21-205
SHIFT CABLE - REMOVAL, GEAR.......21-204,
21s-105
SHIFT COVER - DESCRIPTION.........21-113
SHIFT FORK AND SHAFT - DESCRIPTION . 21-113
SHIFT INTERLOCK SOLENOID -
DESCRIPTION...............21-233,21s-133
SHIFT INTERLOCK SOLENOID -
DIAGNOSIS AND TESTING, BRAKE/
TRANSMISSION..............21-235,21s-135
SHIFT INTERLOCK SOLENOID -
INSTALLATION...............21-236,21s-136
SHIFT INTERLOCK SOLENOID -
OPERATION.................21-233,21s-134
SHIFT INTERLOCK SOLENOID -
REMOVAL..................21-235,21s-135
SHIFT LEVER - INSTALLATION, GEAR.....19-21
SHIFT LEVER - REMOVAL, GEAR........19-21
SHIM SELECTION, ADJUSTMENTS -
OUTPUT FLANGE......................21-7
SHOCK ABSORBER - DESCRIPTION.......2-37
SHOCK ABSORBER - INSTALLATION......2-38
SHOCK ABSORBER - OPERATION.........2-37
SHOCK ABSORBER - REMOVAL..........2-37
SHOCK ABSORBER (UPPER BUSHING) -
ASSEMBLY..........................2-38
SHOCK ABSORBER (UPPER BUSHING) -
DISASSEMBLY........................2-37
SHOE LINING - INSPECTION, REAR
DRUM BRAKE...................5-22,5s-21
SHOES - ADJUSTMENT, PARKING BRAKE . . 5-73,
5s-76
SHOES - ADJUSTMENT, REAR DRUM
BRAKE.........................5-23,5s-22
SHOES - CLEANING, DISC BRAKE....5-16,5-18,
5s-15,5s-17
SHOES - INSPECTION, DISC BRAKE . . 5-16,5-18,
5s-15,5s-17
SHOES - INSTALLATION, REAR DISC
BRAKE.........................5-19,5s-18
SHOES - INSTALLATION, REAR DRUM
BRAKE.........................5-22,5s-21
SHOES - PARKING BRAKE -
INSTALLATION...................5-72,5s-75
SHOES - PARKING BRAKE - REMOVAL....5-67,
5s-69
SHOES - REMOVAL, REAR DISC BRAKE . . . 5-17,
5s-16
SHOES - REMOVAL, REAR DRUM BRAKE . . 5-19,
5s-18
SHOES (CONTINENTAL TEVES BRAKES) -
INSTALLATION, FRONT DISC BRAKE......5s-15
SHOES (CONTINENTAL TEVES BRAKES) -
REMOVAL, FRONT DISC BRAKE.........5s-14
SHOES (DISC/DISC BRAKES) -
INSTALLATION, FRONT DISC BRAKE......5-16
SHOES (DISC/DISC BRAKES) -
REMOVAL, FRONT DISC BRAKE..........5-14
SHOES (DISC/DRUM BRAKES) -
INSTALLATION, FRONT DISC BRAKE......5-17
SHOES (DISC/DRUM BRAKES) -
REMOVAL, FRONT DISC BRAKE..........5-15
SHOES (TRW BRAKES) - INSTALLATION,
FRONT DISC BRAKE..................5s-16
SHOES (TRW BRAKES) - REMOVAL,
FRONT DISC BRAKE
..................5s-14
SHORT TO GROUND - STANDARD
PROCEDURE, TESTING FOR A
........8W-01-9
SHORT TO GROUND ON FUSES
POWERING SEVERAL LOADS -
STANDARD PROCEDURE, TESTING
FOR A
..........................8W-01-10
SHROUD - LOWER - INSTALLATION
......19-22
SHROUD - LOWER - REMOVAL
.........19-21
SHROUD - UPPER - INSTALLATION
......19-23
SHROUD - UPPER - REMOVAL
..........19-23
SHUT DOWN RELAY - DESCRIPTION,
AUTO
...............................8I-3
SHUT DOWN RELAY - OPERATION, AUTO
. . . 8I-3
SIDE - INSTALLATION, LIFTGATE
........23-44
SIDE - REMOVAL, LIFTGATE
............23-44
SIDE COVER - INSTALLATION, FRONT
SEAT CUSHION
......................23-94
SIDE COVER - REMOVAL, FRONT SEAT
CUSHION
...........................23-94SIDE GEAR END PLAY - ADJUSTMENT,
DIFFERENTIAL.......................21-70
SIDE MOLDINGS - INSTALLATION, BODY . . 23-46
SIDE MOLDINGS - REMOVAL, BODY.....23-45
SIDE SHIELD - NO CUPHOLDER -
INSTALLATION, QUAD BUCKET SEAT.....23-97
SIDE SHIELD - NO CUPHOLDER -
REMOVAL, QUAD BUCKET SEAT.........23-97
SIDE SHIELD/CUPHOLDER - FLAP AND
SPRING ASSEMBLY - INSTALLATION,
QUAD BUCKET SEAT.................23-107
SIDE SHIELD/CUPHOLDER - FLAP AND
SPRING ASSEMBLY - REMOVAL, QUAD
BUCKET SEAT......................23-107
SIDE SHIELD/CUPHOLDER -
INSTALLATION, QUAD BUCKET SEAT.....23-96
SIDE SHIELD/CUPHOLDER - REMOVAL,
QUAD BUCKET SEAT..................23-96
SIDE VIEW MIRROR - INSTALLATION.....23-59
SIDE VIEW MIRROR - REMOVAL........23-59
SIDE VIEW MIRROR GLASS -
INSTALLATION.......................23-59
SIDE VIEW MIRROR GLASS - REMOVAL . . 23-59
SIDEVIEW MIRROR - REMOVAL.........8N-49
SIGNAL LAMP - INSTALLATION,
PARK/TURN.........................8L-18
SIGNAL LAMP - REMOVAL, PARK/TURN . . 8L-18
SIGNAL SYSTEM - DESCRIPTION, TURN . . 8L-17
SIGNAL SYSTEM - OPERATION, TURN....8L-18
SILL PLATE - INSTALLATION, LIFTGATE . . . 23-79
SILL PLATE - INSTALLATION, SLIDING
DOOR.............................23-82
SILL PLATE - REMOVAL, LIFTGATE.......23-79
SILL PLATE - REMOVAL, SLIDING DOOR . . 23-82
SILL TRIM PLATE - INSTALLATION,
DOOR.............................23-77
SILL TRIM PLATE - REMOVAL, DOOR....23-77
SINGLE ZONE - DESCRIPTION...........24-2
SINGLE ZONE - OPERATION.............24-4
SLAVE CYLINDER - INSTALLATION........6-11
SLAVE CYLINDER - REMOVAL...........6-11
SLEEVE - INSTALLATION, HEADREST.....23-90
SLEEVE - REMOVAL, HEADREST........23-90
SLIDING DOOR - INSTALLATION.........23-30
SLIDING DOOR - REMOVAL............23-29
SLIDING DOOR ADJUSTMENT -
STANDARD PROCEDURE..............8N-28
SLIDING DOOR ADJUSTMENTS,
ADJUSTMENTS......................23-30
SLIDING DOOR CONTROL MODULE -
DESCRIPTION.......................8E-19
SLIDING DOOR CONTROL MODULE -
INSTALLATION.......................8E-20
SLIDING DOOR CONTROL MODULE -
OPERATION.........................8E-19
SLIDING DOOR CONTROL MODULE -
REMOVAL..........................8E-19
SLIDING DOOR GLASS - INSTALLATION . . 23-110
SLIDING DOOR GLASS - REMOVAL.....23-110
SLIDING DOOR LOCK MOTOR -
INSTALLATION..................8N-44,8N-6
SLIDING DOOR LOCK MOTOR -
REMOVAL......................8N-44,8N-6
SLIDING DOOR MOTOR - DESCRIPTION . . 8N-30
SLIDING DOOR MOTOR - INSTALLATION . . 8N-31
SLIDING DOOR MOTOR - OPERATION....8N-30
SLIDING DOOR MOTOR - REMOVAL
.....8N-30
SLIDING DOOR SILL PLATE -
INSTALLATION
.......................23-82
SLIDING DOOR SILL PLATE - REMOVAL
. . 23-82
SLIDING DOOR STOP BUMPER BEZEL -
INSTALLATION
.......................23-25
SLIDING DOOR STOP BUMPER BEZEL -
REMOVAL
..........................23-25
SLIDING DOOR SYSTEM - DESCRIPTION,
POWER
............................8N-19
SLIDING DOOR SYSTEM - DIAGNOSIS
AND TESTING, POWER
................8N-22
SLIDING DOOR SYSTEM - OPERATION,
POWER
............................8N-21
SLIDING DOOR WEATHERSTRIP -
INSTALLATION
......................23-115
SLIDING DOOR WEATHERSTRIP -
REMOVAL
.........................23-115
SOCKET - INSTALLATION, STABILIZER
....23-33
SOCKET - REMOVAL, STABILIZER
.......23-33
SOLENOID - DESCRIPTION, EVAP/PURGE
. 25-12
32 INDEXRS
Description Group-Page Description Group-Page Description Group-Page

STRIKER - REMOVAL, LATCH . 23-19,23-41,23-62
STRIKER - REMOVAL, REAR LATCH......23-29
STRIPPED THREAD REPAIR - STANDARD
PROCEDURE, MANIFOLD..............9-145
STRUCTURAL ADHESIVE LOCATIONS -
SPECIFICATIONS....................23-156
STRUCTURAL COLLAR - INSTALLATION....9-48
STRUCTURAL COLLAR - REMOVAL.......9-47
STRUT ASSEMBLY - ASSEMBLY..........2-23
STRUT ASSEMBLY - DESCRIPTION.......2-19
STRUT ASSEMBLY - DIAGNOSIS AND
TESTING............................2-20
STRUT ASSEMBLY - DISASSEMBLY.......2-21
STRUT ASSEMBLY - INSTALLATION.......2-25
STRUT ASSEMBLY - OPERATION.........2-20
STRUT ASSEMBLY - REMOVAL...........2-21
STUDS - FRONT - INSTALLATION,
WHEEL MOUNTING...................22-21
STUDS - FRONT - REMOVAL, WHEEL
MOUNTING.........................22-20
STUDS - REAR - INSTALLATION, WHEEL
MOUNTING.........................22-22
STUDS - REAR - REMOVAL, WHEEL
MOUNTING.........................22-21
SUCTION LINE - INSTALLATION . . . 24-107,24-95
SUCTION LINE - REMOVAL.......24-106,24-94
SUN VISOR - INSTALLATION...........23-82
SUN VISOR - REMOVAL...............23-82
SUN VISOR SUPPORT - INSTALLATION.....23-83
SUN VISOR SUPPORT - REMOVAL.......23-83
SUNROOF - DESCRIPTION............23-116
SUNROOF - DIAGNOSIS AND TESTING . . . 23-116
SUNROOF ASSEMBLY - INSTALLATION . . 23-120
SUNROOF ASSEMBLY - REMOVAL......23-120
SUNROOF GLASS PANEL ADJUSTMENT,
ADJUSTMENTS.....................23-120
SUNROOF MOTOR - INSTALLATION.....23-121
SUNROOF MOTOR - REMOVAL.........23-121
SUNROOF SWITCH - INSTALLATION.....23-123
SUNROOF SWITCH - REMOVAL........23-123
SUNSHADE - INSTALLATION...........23-121
SUNSHADE - REMOVAL..............23-120
SUPPLEMENTAL CABIN HEATER -
DIAGNOSIS AND TESTING, DIESEL......24-113
SUPPLEMENTAL DIESEL HEATER
WIRING - INSTALLATION.............24-119
SUPPLEMENTAL DIESEL HEATER
WIRING - REMOVAL.................24-119
SUPPLY - PCM OUTPUT - OPERATION, 5
VOLT ..............................8E-15
SUPPLY - PCM OUTPUT - SBEC
CONTROLLER - OPERATION, 8-VOLT.....8E-15
SUPPORT - INSTALLATION, LUMBAR....23-106
SUPPORT - INSTALLATION, SUN VISOR . . . 23-83
SUPPORT - REMOVAL, LUMBAR.......23-106
SUPPORT - REMOVAL, SUN VISOR......23-83
SUPPORT CYLINDER - INSTALLATION....23-43
SUPPORT CYLINDER - REMOVAL........23-43
SUPPORT PLATE - DRUM BRAKE -
INSTALLATION...................5-56,5s-58
SUPPORT PLATE - DRUM BRAKE -
REMOVAL......................5-56,5s-58
SUPPRESSION COMPONENTS -
DESCRIPTION, RADIO NOISE...........8A-11
SUPPRESSION COMPONENTS -
OPERATION, RADIO NOISE.............8A-12
SURFACE PREPARATION - STANDARD
PROCEDURE, ENGINE GASKET.......9-11,9-85
SUSPENSION - DESCRIPTION, FRONT......2-2
SUSPENSION - DESCRIPTION, REAR
......2-27
SUSPENSION - OPERATION, FRONT
........2-2
SUSPENSION - OPERATION, REAR
........2-28
SUSPENSION AND STEERING -
DIAGNOSIS AND TESTING
..............2-50
SUSPENSION FASTENER TORQUE,
SPECIFICATIONS - FRONT
................2-3
SUSPENSION FASTENER TORQUE,
SPECIFICATIONS - REAR
................2-28
SUSPENSION, SPECIAL TOOLS - FRONT
....2-3
SUSPENSION, SPECIAL TOOLS - REAR
....2-28
SWITCH - DESCRIPTION
................8P-6
SWITCH - DESCRIPTION, AUTOSTICK
. . . 21-189
SWITCH - DESCRIPTION, BRAKE FLUID
LEVEL
..........................5-10,5s-9
SWITCH - DESCRIPTION, BRAKE LAMP
....8L-4
SWITCH - DESCRIPTION, DOOR
CYLINDER LOCK
.....................8N-40SWITCH - DESCRIPTION, DRIVER
HEATED SEAT ........................8G-8
SWITCH - DESCRIPTION, DRIVER SEAT . . 8N-10,
8N-53
SWITCH - DESCRIPTION, EXTERIOR
HANDLE...........................8N-11
SWITCH - DESCRIPTION, FULL OPEN....8N-12,
8N-31
SWITCH - DESCRIPTION, HORN..........8H-5
SWITCH - DESCRIPTION, LEFT B-PILLAR . 8N-32
SWITCH - DESCRIPTION, MEMORY SET . . 8N-12,
8N-55
SWITCH - DESCRIPTION, OIL PRESSURE . 9-141
SWITCH - DESCRIPTION, PASSENGER
HEATED SEAT .......................8G-12
SWITCH - DESCRIPTION, PASSENGER
SEAT.........................8N-13,8N-56
SWITCH - DESCRIPTION, REAR
WINDOW DEFOGGER..................8G-4
SWITCH - DESCRIPTION, REAR
WIPER/WASHER.....................8R-11
SWITCH - DESCRIPTION, RIGHT
B-PILLAR..........................8N-32
SWITCH - DIAGNOSIS AND TESTING,
BRAKE LAMP........................8L-4
SWITCH - DIAGNOSIS AND TESTING,
DOOR CYLINDER LOCK...............8N-40
SWITCH - DIAGNOSIS AND TESTING,
DOOR LOCK....................8N-4,8N-41
SWITCH - DIAGNOSIS AND TESTING,
DRIVER HEATED SEAT.................8G-9
SWITCH - DIAGNOSIS AND TESTING,
DRIVER SEAT...................8N-11,8N-54
SWITCH - DIAGNOSIS AND TESTING,
FAILED PARK........................8R-2
SWITCH - DIAGNOSIS AND TESTING,
FRONT WIPER/WASHER................8R-2
SWITCH - DIAGNOSIS AND TESTING,
HEADLAMP.........................8L-12
SWITCH - DIAGNOSIS AND TESTING,
MEMORY.....................8N-13,8N-56
SWITCH - DIAGNOSIS AND TESTING,
MULTI-FUNCTION....................8L-18
SWITCH - DIAGNOSIS AND TESTING,
PASSENGER HEATED SEAT.............8G-13
SWITCH - DIAGNOSIS AND TESTING,
PASSENGER SEAT..............8N-14,8N-57
SWITCH - DIAGNOSIS AND TESTING,
REMOTE...........................8N-49
SWITCH - DIAGNOSIS AND TESTING,
TRACTION CONTROL...................5-82
SWITCH - DIAGNOSIS AND TESTING,
WINDOW...........................8N-64
SWITCH - EXPORT - DESCRIPTION,
DOOR CYLINDER LOCK................8N-3
SWITCH - EXPORT - DESCRIPTION,
POWER FOLDAWAY MIRROR...........8N-48
SWITCH - EXPORT - DIAGNOSIS AND
TESTING, DOOR CYLINDER LOCK........8N-3
SWITCH - EXPORT - INSTALLATION,
DOOR CYLINDER LOCK................8N-4
SWITCH - EXPORT - INSTALLATION,
HOOD AJAR.........................8Q-3
SWITCH - EXPORT - INSTALLATION,
POWER FOLDAWAY MIRROR
...........8N-49
SWITCH - EXPORT - OPERATION, DOOR
CYLINDER LOCK
......................8N-3
SWITCH - EXPORT - OPERATION,
POWER FOLDAWAY MIRROR
...........8N-48
SWITCH - EXPORT - REMOVAL, DOOR
CYLINDER LOCK
......................8N-3
SWITCH - EXPORT - REMOVAL, HOOD
AJAR
...............................8Q-3
SWITCH - EXPORT - REMOVAL, POWER
FOLDAWAY MIRROR
..................8N-48
SWITCH - INSTALLATION
...............8P-6
SWITCH - INSTALLATION, ADJUSTABLE
PEDALS
............................5s-10
SWITCH - INSTALLATION, BACK-UP
LAMP
..............................21-62
SWITCH - INSTALLATION, BRAKE FLUID
LEVEL
.........................5-11,5s-10
SWITCH - INSTALLATION, BRAKE LAMP
. . . 8L-5
SWITCH - INSTALLATION, CENTER
CONSOLE LAMP
.....................8L-21
SWITCH - INSTALLATION, CLUTCH
PEDAL INTERLOCK
....................6-14SWITCH - INSTALLATION, CLUTCH
PEDAL UPSTOP.......................6-16
SWITCH - INSTALLATION, DOOR
CYLINDER LOCK.....................8N-41
SWITCH - INSTALLATION, DOOR LOCK....8N-4,
8N-42
SWITCH - INSTALLATION, DRIVER
HEATED SEAT .......................8G-10
SWITCH - INSTALLATION, DRIVER SEAT . . 8N-12,
8N-55
SWITCH - INSTALLATION, EXTERIOR
HANDLE...........................8N-12
SWITCH - INSTALLATION, FULL OPEN....8N-13
SWITCH - INSTALLATION, GLOVE BOX
LAMP..............................8L-22
SWITCH - INSTALLATION, HEADLAMP....8L-13
SWITCH - INSTALLATION, IGNITION......19-16
SWITCH - INSTALLATION, LEFT
B-PILLAR..........................8N-32
SWITCH - INSTALLATION, MEMORY SET . 8N-13,
8N-56
SWITCH - INSTALLATION, MULTI-
FUNCTION..........................8L-18
SWITCH - INSTALLATION, OIL
PRESSURE.....................9-141,9-54
SWITCH - INSTALLATION, PASSENGER
HEATED SEAT .......................8G-14
SWITCH - INSTALLATION, PASSENGER
SEAT.........................8N-15,8N-57
SWITCH - INSTALLATION, REMOTE......8N-49
SWITCH - INSTALLATION, RIGHT
B-PILLAR..........................8N-32
SWITCH - INSTALLATION, SUNROOF....23-123
SWITCH - INSTALLATION, WASHER
FLUID LEVEL........................8R-12
SWITCH - INSTALLATION, WINDOW.....8N-65
SWITCH - OPERATION.................8P-6
SWITCH - OPERATION, AUTOSTICK.....21-189
SWITCH - OPERATION, BRAKE FLUID
LEVEL..........................5-10,5s-9
SWITCH - OPERATION, BRAKE LAMP......8L-4
SWITCH - OPERATION, DOOR CYLINDER
LOCK..............................8N-40
SWITCH - OPERATION, DRIVER HEATED
SEAT ...............................8G-8
SWITCH - OPERATION, DRIVER SEAT....8N-11,
8N-54
SWITCH - OPERATION, EXTERIOR
HANDLE...........................8N-11
SWITCH - OPERATION, FULL OPEN . 8N-12,8N-31
SWITCH - OPERATION, LEFT B-PILLAR . . . 8N-32
SWITCH - OPERATION, MEMORY SET . . . 8N-13,
8N-56
SWITCH - OPERATION, OIL PRESSURE . . . 9-141
SWITCH - OPERATION, PASSENGER
HEATED SEAT .......................8G-12
SWITCH - OPERATION, PASSENGER
SEAT.........................8N-13,8N-56
SWITCH - OPERATION, REAR WINDOW
DEFOGGER..........................8G-4
SWITCH - OPERATION, REAR WIPER/
WASHER...........................8R-11
SWITCH - OPERATION, RIGHT B-PILLAR . . 8N-32
SWITCH - REMOVAL...................8P-6
SWITCH - REMOVAL, ADJUSTABLE
PEDALS............................5s-10
SWITCH - REMOVAL, BACK-UP LAMP....21-62
SWITCH - REMOVAL, BRAKE FLUID
LEVEL.........................5-11,5s-10
SWITCH - REMOVAL, BRAKE LAMP.......8L-5
SWITCH - REMOVAL, CENTER CONSOLE
LAMP..............................8L-21
SWITCH - REMOVAL, CLUTCH PEDAL
INTERLOCK..........................6-13
SWITCH - REMOVAL, CLUTCH PEDAL
UPSTOP.............................6-15
SWITCH - REMOVAL, DOOR CYLINDER
LOCK..............................8N-41
SWITCH - REMOVAL, DOOR LOCK . . 8N-4,8N-42
SWITCH - REMOVAL, DRIVER HEATED
SEAT ..............................8G-10
SWITCH - REMOVAL, DRIVER SEAT.....8N-12,
8N-55
SWITCH - REMOVAL, EXTERIOR HANDLE
. 8N-11
SWITCH - REMOVAL, FULL OPEN
.......8N-13
SWITCH - REMOVAL, GLOVE BOX LAMP
. . 8L-22
SWITCH - REMOVAL, HEADLAMP
........8L-13
SWITCH - REMOVAL, IGNITION
.........19-14
34 INDEXRS
Description Group-Page Description Group-Page Description Group-Page

SWITCH - REMOVAL, LEFT B-PILLAR....8N-32
SWITCH - REMOVAL, MEMORY SET.....8N-13,
8N-56
SWITCH - REMOVAL, MULTI-FUNCTION . . . 8L-18
SWITCH - REMOVAL, OIL PRESSURE....9-141,
9-54
SWITCH - REMOVAL, PASSENGER
HEATED SEAT .......................8G-14
SWITCH - REMOVAL, PASSENGER SEAT . . 8N-14,
8N-57
SWITCH - REMOVAL, REMOTE..........8N-49
SWITCH - REMOVAL, RIGHT B-PILLAR . . . 8N-32
SWITCH - REMOVAL, SUNROOF........23-123
SWITCH - REMOVAL, WASHER FLUID
LEVEL.............................8R-12
SWITCH - REMOVAL, WINDOW.........8N-65
SWITCH ASSY - DESCRIPTION,
SOLENOID/PRESSURE.........21-237,21s-137
SWITCH ASSY - INSTALLATION,
SOLENOID/PRESSURE.........21-239,21s-139
SWITCH ASSY - OPERATION, SOLENOID/
PRESSURE..................21-237,21s-137
SWITCH ASSY - REMOVAL, SOLENOID/
PRESSURE..................21-238,21s-138
SWITCHES - DESCRIPTION, REMOTE.....8A-12
SWITCHES - DIAGNOSIS AND TESTING,
REMOTE...........................8A-12
SWITCHES - INSTALLATION, REMOTE....8A-14
SWITCHES - OPERATION, REMOTE......8A-12
SWITCHES - REMOVAL, REMOTE........8A-13
SYMBOLS - DESCRIPTION,
INTERNATIONAL....................Intro.-5
SYMBOLS - DESCRIPTION,
INTERNATIONAL.......................0-1
SYNCHRONIZER - DESCRIPTION.......21-114
SYNCHRONIZER - DISASSEMBLY.......21-114
SYNCHRONIZING CABLE ADJUSTMENT,
INSTALLATION.................23-102,23-88
T850 MANUAL TRANSAXLE - ASSEMBLY . . 21-42
T850 MANUAL TRANSAXLE -
DESCRIPTION.......................21-21
T850 MANUAL TRANSAXLE -
DISASSEMBLY.......................21-35
T850 MANUAL TRANSAXLE -
INSTALLATION.......................21-51
T850 MANUAL TRANSAXLE -
OPERATION.........................21-24
T850 MANUAL TRANSAXLE - REMOVAL . . 21-31
T850 MANUAL TRANSAXLE -
SPECIFICATIONS.....................21-56
T850 TRANSAXLE - SPECIAL TOOLS.......6-6
T850 TRANSAXLE - SPECIAL TOOLS.....21-58
TABLE, SPECIFICATIONS -
SPECIFICATIONS.................8N-29,8N-9
TAIL LAMP - INSTALLATION............8L-19
TAIL LAMP - REMOVAL................8L-18
TAIL LAMP UNIT - INSTALLATION.......8L-19
TAIL LAMP UNIT - REMOVAL...........8L-19
TANK - DESCRIPTION, FUEL............14-10
TANK - INSTALLATION, FUEL...........14-12
TANK - OPERATION, FUEL..............14-11
TANK - REMOVAL, FUEL...............14-11
TANK - STANDARD PROCEDURE,
DRAINING FUEL......................14-2
TANK FILLER TUBE - INSTALLATION,
FUEL..............................14-13
TANK FILLER TUBE - REMOVAL, FUEL....14-12
TAPE ATTACHED - INSTALLATION,
EXTERIOR NAME PLATES..............23-51
TAPE ATTACHED - REMOVAL, EXTERIOR
NAME PLATES.......................23-51
TASK MANAGER - DESCRIPTION........25-24
TASK MANAGER - OPERATION..........25-24
TD - INSTALLATION, CLUTCH DISC AND
PRESSURE PLATE - 2.5L...............6-12
TD - REMOVAL, CLUTCH DISC AND
PRESSURE PLATE - 2.5L...............6-11
TEMP SENSOR - DESCRIPTION,
AMBIENT..........................8M-11
TEMP SENSOR - OPERATION, AMBIENT
. . 8M-11
TEMPERATURE CONTROL (ATC) -
INSTALLATION, AUTOMATIC
............24-29
TEMPERATURE CONTROL (ATC) -
REMOVAL, AUTOMATIC
................24-28
TEMPERATURE CONTROL (MTC) -
INSTALLATION, MANUAL
..............24-29
TEMPERATURE CONTROL (MTC) -
REMOVAL, MANUAL
..................24-29TEMPERATURE CONTROL SYSTEM -
OPERATION, AUTOMATIC.............24-112
TEMPERATURE CONTROL SYSTEM -
OPERATION, MANUAL................24-112
TEMPERATURE SENSOR - 2.4L -
DESCRIPTION, ENGINE COOLANT.........7-21
TEMPERATURE SENSOR - 2.4L -
INSTALLATION, ENGINE COOLANT........7-21
TEMPERATURE SENSOR - 2.4L -
REMOVAL, ENGINE COOLANT............7-21
TEMPERATURE SENSOR - 3.3/3.8L -
DESCRIPTION, ENGINE COOLANT.........7-21
TEMPERATURE SENSOR - 3.3/3.8L -
INSTALLATION, ENGINE COOLANT........7-22
TEMPERATURE SENSOR - 3.3/3.8L -
REMOVAL, ENGINE COOLANT............7-21
TEMPERATURE SENSOR - DESCRIPTION,
BATTERY...........................8F-23
TEMPERATURE SENSOR - DESCRIPTION,
EVAPORATOR.......................24-27
TEMPERATURE SENSOR - DESCRIPTION,
INFRARED..........................24-29
TEMPERATURE SENSOR - DESCRIPTION,
INLET AIR..........................14-30
TEMPERATURE SENSOR - DIAGNOSIS
AND TESTING, AMBIENT..............8M-12
TEMPERATURE SENSOR - OPERATION,
BATTERY...........................8F-23
TEMPERATURE SENSOR - OPERATION,
EVAPORATOR.......................24-28
TEMPERATURE SENSOR - OPERATION,
INFRARED..........................24-29
TEMPERATURE SENSOR - REMOVAL,
BATTERY.............................8F-23
TEMPERATURE SENSOR -
SPECIFICATIONS, BATTERY.............8F-22
TEMPERATURE SENSOR CIRCUIT -
DIAGNOSIS AND TESTING, AMBIENT....8M-12
TENSION - STANDARD PROCEDURE,
CHECKING POWER STEERING BELT........7-8
TENSION RELEASE - STANDARD
PROCEDURE, PARKING BRAKE
AUTOMATIC ADJUSTER............5-58,5s-61
TENSION RESET - STANDARD
PROCEDURE, PARKING BRAKE
AUTOMATIC ADJUSTER............5-59,5s-61
TENSION, SPECIFICATIONS -
ACCESSORY DRIVE BELT................7-5
TENSIONER - 2.4L - INSTALLATION,
BELT ...............................7-10
TENSIONER - 2.4L - REMOVAL, BELT......7-10
TENSIONER - 3.3/3.8L - INSTALLATION,
BELT ...............................7-12
TENSIONER - 3.3/3.8L - REMOVAL, BELT . . . 7-12
TENSIONER - DESCRIPTION, SEAT BELT . . 8O-17
TENSIONER - OPERATION, SEAT BELT....8O-17
TENSIONER & PULLEY - INSTALLATION,
TIMING BELT.........................9-69
TENSIONER & PULLEY - REMOVAL,
TIMING BELT.........................9-68
TERMINAL - INSTALLATION.........8W-01-14
TERMINAL - REMOVAL.............8W-01-14
TERMINAL REPAIR - STANDARD
PROCEDURE, GRID LINE...............8G-4
TEST - 2.5L DIESEL - DIAGNOSIS AND
TESTING, SYSTEM CHARGE LEVEL......24-68
TEST - DIAGNOSIS AND TESTING, A/C
COOL DOWN.........................24-6
TEST - DIAGNOSIS AND TESTING, A/C
PERFORMANCE.......................24-7
TEST - DIAGNOSIS AND TESTING,
CONTROL CIRCUIT..............8F-30,8F-32
TEST - DIAGNOSIS AND TESTING,
COOLING SYSTEM LEAK.................7-2
TEST - DIAGNOSIS AND TESTING,
CYLINDER COMBUSTION PRESSURE
LEAKAGE.........................9-83,9-9
TEST - DIAGNOSIS AND TESTING,
CYLINDER COMPRESSION PRESSURE
. . 9-83,9-9
TEST - DIAGNOSIS AND TESTING, FEED
CIRCUIT
.......................8F-33,8F-35
TEST - DIAGNOSIS AND TESTING, FEED
CIRCUIT RESISTANCE
............8F-32,8F-34
TEST - DIAGNOSIS AND TESTING,
HEATER PERFORMANCE
...............24-10
TEST - DIAGNOSIS AND TESTING,
POWER STEERING SYSTEM FLOW
AND PRESSURE
......................19-1TEST - DIAGNOSIS AND TESTING, ROAD . . . 8P-3
TEST - DIAGNOSIS AND TESTING,
ROAD.......................21-119,21s-27
TEST - DIAGNOSIS AND TESTING,
STARTING SYSTEM..............8F-28,8F-30
TEST - GASOLINE ENGINES -
DIAGNOSIS AND TESTING, SYSTEM
CHARGE LEVEL......................24-67
TEST - STANDARD PROCEDURE,
IGNITION-OFF DRAW..................8F-13
TEST - STANDARD PROCEDURE,
OPEN-CIRCUIT VOLTAGE...............8F-13
TEST MODE, OPERATION - DRB IIIT
STATE DISPLAY.......................25-9
TESTS - DIAGNOSIS AND TESTING,
CLUTCH AIR PRESSURE........21-122,21s-30
TESTS - DIAGNOSIS AND TESTING,
HYDRAULIC PRESSURE........21-120,21s-28
THEFT SECURITY - DESCRIPTION,
VEHICLE............................8Q-1
THEFT SECURITY - OPERATION, VEHICLE . . 8Q-1
THEFT SECURITY SYSTEM - DIAGNOSIS
AND TESTING, VEHICLE................8Q-3
THERMOSTAT - 2.4L - INSTALLATION,
ENGINE COOLANT.....................7-23
THERMOSTAT - 2.4L - REMOVAL,
ENGINE COOLANT.....................7-23
THERMOSTAT - 3.3/3.8L -
INSTALLATION, ENGINE COOLANT........7-24
THERMOSTAT - 3.3/3.8L - REMOVAL,
ENGINE COOLANT.....................7-23
THERMOSTAT - DESCRIPTION, ENGINE
COOLANT............................7-22
THERMOSTAT - DIAGNOSIS AND
TESTING, ENGINE COOLANT.............7-23
THERMOSTAT - OPERATION, ENGINE
COOLANT............................7-22
THERMOWRAP - DESCRIPTION.........8F-19
THERMOWRAP - INSTALLATION.........8F-19
THERMOWRAP - OPERATION...........8F-19
THERMOWRAP - REMOVAL............8F-19
THIRD ROW - INSTALLATION, BENCH
SEAT RISER........................23-101
THIRD ROW - REMOVAL, BENCH SEAT
RISER............................23-101
THREAD REPAIR - DESCRIPTION, FRONT
CRADLE CROSSMEMBER...............13-9
THREAD REPAIR - STANDARD
PROCEDURE, MANIFOLD STRIPPED......9-145
THREADED HOLE REPAIR -
DESCRIPTION......................Intro.-5
THREADS - STANDARD PROCEDURE,
REPAIR OF DAMAGED OR WORN.....9-10,9-86
THREE PASSENGER BENCH -
INSTALLATION, SEAT BELT BUCKLE -
SECOND ROW.......................8O-15
THREE PASSENGER BENCH - REMOVAL,
SEAT BELT BUCKLE - SECOND ROW.....8O-15
THREE ZONE - DESCRIPTION,
AUTOMATIC..........................24-3
THREE ZONE - DESCRIPTION, MANUAL....24-2
THREE ZONE - OPERATION, MANUAL.....24-5
THREE ZONE ATC - OPERATION..........24-5
THROTTLE BODY - DESCRIPTION........14-35
THROTTLE BODY - INSTALLATION.......14-35
THROTTLE BODY - OPERATION.........14-35
THROTTLE BODY - REMOVAL...........14-35
THROTTLE CONTROL CABLE -
INSTALLATION.......................14-36
THROTTLE CONTROL CABLE - REMOVAL . . 14-35
THROTTLE POSITION SENSOR -
DESCRIPTION.......................14-36
THROTTLE POSITION SENSOR -
OPERATION.........................14-36
TIE ROD - INSTALLATION, OUTER.......19-34
TIE ROD - REMOVAL, OUTER...........19-34
TIMING BELT - INSTALLATION...........9-65
TIMING BELT - REMOVAL...............9-63
TIMING BELT COVER(S) - INSTALLATION . . . 9-62
TIMING BELT COVER(S) - REMOVAL
......9-61
TIMING BELT TENSIONER & PULLEY -
INSTALLATION
........................9-69
TIMING BELT TENSIONER & PULLEY -
REMOVAL
...........................9-68
TIMING CHAIN AND CAMSHAFT
SPROCKET - INSTALLATION
............9-157
TIMING CHAIN AND CAMSHAFT
SPROCKET - REMOVAL
................9-156
RSINDEX35
Description Group-Page Description Group-Page Description Group-Page