tire size CHRYSLER VOYAGER 2020 Vehicle Warranty

MAX LOAD AND INFLATION
The maximum load and inflation pressure is marked on the tire sidewall
in English and metric units.
PLY COMPOSITION AND MATERIALS
The number of plies and their generic composition of cord materials in
the sidewall and tread areas can be found on at least one sidewall of a
tire.
RADIAL MARKING
A radial ply tire will have the word “radial” marked on at least one
sidewall. An “R” found in the tire size marking also refers to the tire
being a radial ply tire.
UNIFORM TIRE QUALITY GRADING SYSTEM (UTQG)
The Uniform Tire Quality Grading Standards (UTQG) were created to
help you make an informed decision when purchasing passenger car tires
by providing relative information about a tire’s treadwear, traction, and
temperature characteristics. Here is a breakdown of the different catego-
ries that the UTQG grades:
TREAD WEAR
The tread wear grade is a comparative rating based on the wear rate of
the tire when tested under controlled conditions on a specified govern-
ment test course. For example, a tire graded150would wear one and a
half (1½) times as well on the government course as a tire graded 100. The
relative performance of tires depends upon the actual conditions of their
use, however, and may depart significantly from the norm due to
variations in driving habits, service practices, and differences in road
characteristics and climate.
TRACTION
The traction grades, from highest to lowest, are AA, A, BandC. Those
grades represent the tire’s ability to stop on wet pavement as measured
under controlled conditions on specific government test surfaces of
asphalt and concrete. A tire marked C may have poor traction perfor-
mance.
FALKEN TIRE CORPORATION
107

•EXPLOSION OF TIRE/RIM ASSEMBLY DUE TO IMPROPER
MOUNTING. Only specially trained persons should mount tires.
• FAILURE TO MOUNT RADIAL TIRES ON APPROVED RIMS.
• FAILURE TO DEFLATE SINGLE OR DUAL ASSEMBLIES COM-
PLETELY BEFORE DEMOUNTING.
• TIRE SPINNING. On slippery surfaces such as snow, mud, ice, etc.,
do not spin tires in excess of 35 mph (55 kph), as indicated on the
speedometer.
• EXCESSIVE WHEEL SPINNING. This can also result in tire disinte-
gration or axle failure.
WARNING!
Vehicle handling, traction, ride comfort and other performance
parameters may be significantly affected by a change in tire size or
type. Before replacing tires, always consult and follow the vehicle
owner ’s manual because some vehicle manufacturers prohibit
changing tire size. When selecting tires that are different from the
original equipment size make certain:
1. The tires have adequate load-carrying capacity based on the vehicle placard,
2. The tires have sufficient inflation pressure to carry the load and
3. There is proper clearance with no interference points between the tire and vehicle.
The consumer must be aware to always drive safely and obey all
traffic laws. Avoid sudden, sharp turns or aggressive lane changes.
Failure to follow any of these warnings may result in loss of control
of the vehicle, leading to an accident and serious injury or death.
TIRE CARE AND MAINTENANCE GUIDE
The easiest way to help ensure satisfactory mileage and performance
from your Goodyear or Dunlop tires is to give them a simple but frequent
(at least monthly) inspection for proper inflation, even tread wear and the
presence of any damage.
DO MAINTAIN PROPER INFLATION PRESSURE IN YOUR TIRES
Proper inflation pressure is necessary for optimum tire performance,
safety and fuel economy. Check inflation pressures at least once a month
and before long trips. Use an accurate tire pressure gauge. Always check
GOODYEAR DUNLOP TIRES
128

DON’T MIX TIRES OF DIFFERENT SIZES AND TYPES ON THE
SAME AXLE
For optimum handling and control, Goodyear recommends fitment of
four (4) tires of the same type and size unless otherwise specified by the
vehicle manufacturer.
WARNING!
Before you replace your tires, always consult the vehicle owner ’s
manual and follow the vehicle manufacturer ’s replacement tire
recommendations. Vehicle handling may be significantly affected
by a change in tire size or type. When selecting tires that are
different from the Original Equipment size, see a professional
installer in order to make certain that proper clearance, load-
carrying capacity and inflation pressure are selected. Never exceed
the maximum load capacity and inflation pressure listed on the
sidewall of the tire. Always drive safely and obey all traffic laws.
Avoid sudden, sharp turns or aggressive lane changes. Failure to
follow this warning may result in loss of control of the vehicle,
leading to an accident and serious injury or death.
When replacing tires, you must maintain the outside diameter and
load-carrying capacity of the Original Equipment tire. Inflation pressure
may need to be adjusted to avoid overloading the tire. Consult the Tire &
Rim Association Load and Inflation Tables, ETRTO or JATMA standards
for correct load and inflation information.
NEVER FIT TIRES TO A VEHICLE THAT HAVE LESS LOAD-
CARRYING CAPACITY THAN REQUIRED BY THE ORIGINAL
EQUIPMENT MANUFACTURER
Examples: Many vehicles, such as large passenger vans, require Load
Range E tires as designated by the vehicle manufacturer. Fitment of a tire,
such as a Load Range D, with less carrying capacity is not allowed. In
other cases, tires of the same size may carry different load indexes in the
service description. You must make certain the replacement tires fitted to
the vehicle have a load-carrying capacity equal to or greater than what
the Original Equipment manufacturer specifies.
GOODYEAR DUNLOP TIRES
132

NOTE:

Goodyear
manufactured
and/or
marketed
European-
Metric

passenger
tires
and
P-Metric
passenger
tires
are
interchangeable
as
long

as
they
have
the
same
section
width,
same
aspect
ratio,
same
rim

diameter.
CAUTION!
Never substitute a “Standard Load” (SL) tire for an Extra Load (XL)
or Reinforced tire. If the vehicle was originally equipped with
“Extra Load” (XL) or Reinforced tires, replace those tires with
similar-sized Extra Load (XL) or Reinforced tires.
GOODYEAR DUNLOP TIRES
FOLLOW THESE ADDITIONAL GUIDELINES
When
installing
only
two
tires,
fit
the
tires
with
the
deepest
tread
depth

on
the
rear
axle.
If
radials
and
non-radials
must
be
fitted
to
the
same

vehicle,
fit
radials
on
rear
axle.
Never
mix
radials
and
non-radials
on
the

same
axle.
When
fitting

tires
or
all-season
tires
to

performance
vehicles,
always
fit
in
sets
of
four.
It
is
not
recommended

to

fit
tires
with
different
speed
ratings.
If
tires
with
different
speed
ratings

are
installed
on
a
vehicle,
they
should
be
installed
with
like
pairs
on

the
same
axle.
The
speed
capability
of
the
vehicle
will
become
limited
to
that
of
the

lowest
speed
rated
tires.
Use
of
lift
kits
with
some
vehicle/tire
combinations
can
cause
instability.

When
changing
tire
sizes,


always
consult
Dealer
for
optimum
rim
width

and
carefully
check
vehicle/tire
clearances.
RETREADED TIRES
Retreaded
passenger
and
light
truck
tires
are
not
warranted
by
Goodyear

for
any
reason.
Speed
ratings
and
U.S.
Department
of
Transportation
test

compliance
certifications
are
voided
for
retreaded
tires.
DOMAINTAIN VEHICLESUSPENSION, WHEELALIGNMENT
AND BALANCE AND ROTATE YOURTIRES
Lack
of
rotation,
worn
suspension
parts,
underinflation/

overinflation,
wheel
imbalance
and
misalignment
can
cause
vibration

or
irregular
tire
wear.
Rotate
your
tires
according
to
your
vehicle

manufacturer ’s
recom-mendations
or
at
maximum
intervals
of
6,000

miles
/
10,000
km.
133

GENERAL EXCLUSIONS
1. No Hankook Tire employee, retailer or dealer has the authority tomake any warranty, representation, promise or agreement on behalf of
Hankook Tire except as stated in this policy.
2. Tires used in racing related activities or competitive events are not covered by this warranty.
3. Limitation of remedy: to the extent permitted by law, HANKOOK disclaims liability for all consequential and incidental damages. Some
provinces and states do not allow the exclusion or limitation of
incidental or consequential damages, so the above limitation or
exclusion may not apply to you. This warranty gives you specific legal
rights, and you may also have the rights which vary from province to
province in Canada, and from state to state in the U.S.A.
HANKOOK’S OBLIGATIONS
Replacement qualifying under this warranty will be made by a partici-
pating Hankook Dealer or a participating Car Dealer.
OWNER’S OBLIGATIONS
1. You must present the tire to a participating Hankook Dealer or aparticipating Car Dealer.
2. For free replacement, a proof of purchase date such as car dealer invoice should be presented.
3. No claim will be recognized unless submitted on a Hankook claim form completely filled out and signed by the owner or a participating
Hankook Dealer or Car Dealer.
WARNING FOR YOUR SAFETY
•TIRE DEMOUNTING AND MOUNTING
Improper tire mounting and inflation procedures may cause tire beads
to break with explosive force during installation of the tire on the rim,
causing personal injury and property damage. Follow the Rubber
Manufacturers Association installation and safety procedure for
mounting and inflating tires. Tire and rim must match in size. Rim
parts must match by manufacturer ’s design. Clean rim. Lubricate rim
HANKOOK TIRES
141

•WORN TIRES
Never drive on worn tires. Tires should be replaced by trained
personnel when 2/32 nds inch (1.6 mm) of tread depth remain, as
indicated by treadwear indicators molded into the tread grooves. Use
of worn-out tires (less than 2/32 nds of an inch remaining tread depth)
increases the probability of tire failure. In most states, it is illegal to
drive with less than 2/32 nds of an inch of remaining tread depth.
• SPEED LIMITS
Operating your vehicle in excess of lawful speed limits or the
maximum speeds justified by driving conditions can be dangerous.
Excessive speed creates heat buildup in a tire, leading to possible tire
failure.
• SPEED-RATED TIRES
Speed-rated tires are identified by letters S, T, H, V, W, or Z as either
part of the size designation (e.g., HR), or part of the service description
adjacent to the size designation (e.g., 94H) and indicates the maximum
speed capability of the tire when properly loaded and inflated.
However, even when properly loaded and inflated, driving for pro-
longed periods at high speeds can cause tire damage and possible tire
failure which could lead to an accident. Original equipment speed-
rated tires must be replaced with tires of the same or higher speed
rating if the speed capability of the vehicle is to be maintained.
Consult your Hankook dealer for the tires best suited to your vehicle
driving habit. Repairing of speed-rated tires must be done in accor-
dance with RMA repair procedures and is limited to one 1/4 diameter
repair in the tread area.
• TIRE ROTATION
Rotate your tires for longer tire life. Front and rear tires perform
different jobs and can wear differently. Consult your vehicle Owner ’s
Manual for mileage recommendations and rotation patterns.
HANKOOK TIRES
143

12. Tires that are misapplied due to insufficient speed rating, or under-sized, or oversized tires.
13. Tires that have become unserviceable because chemical corrosion, vandalism, chains and flat spotting.
14. Tires involved in any racing-related activities.
15. This limited warranty applies only to the original purchaser and is nontransferable.
OWNERS OBLIGATION:
In order to be eligible for KUMHO’s limited warranty program, the
owner must:
1. Conform to all pertaining policies detailed herein.
2. Present tire to any authorized KUMHO dealer for inspection alongwith a copy of their original purchase receipt. Dealer will inspect tire
in order to identify whether or not it qualifies for warranty based on
the policies detailed herein.
3. Pay the amounts due on a new tire, less the amount of credit including taxes, mounting and balancing charges and/or the cost of other
services ordered.
To
locate
an
authorized
KUMHO/Marshal
dealer,
use
our
web
address

WWW.KUMHOTIREUSA.COM
or
call
(800)
HI-KUMHO

1-800-445-8646
.
OTHER
RIGHTS:
This
limited
warranty
gives
the
owner
of
KUMHO
tires
specific
legal

rights
and
you
may
also
have
other
rights,
which
vary
from
state
to
state.
KUMHO TIRES
149

3. Applicable taxes and costs of mounting and balancing and any otherservice charges are payable by the owner.
4. The owner must rotate the tires every 5,000 miles.
5. The following are exclusions to the Limited Tread Wear Warranty: •Tires branded NA,Blem, etc.
• Tires exhibiting uneven or rapid wear which is caused by mechanical
irregularity in the vehicle such as misalignment, (a measured tread
difference of 2/32nds of an inch or more across the tread on the same
tire).
• Tires worn-out or damaged due to:
Improper inflation, improper mounting, uneven wear, overloading or
off-road driving, run flat or racing, accident, fire or chemicals, use on
RV or commercial vehicle, vandalism or gross abuse, defective
mechanical condition of vehicle, road hazard damage (e.g., irrepa-
rable cut, puncture, snag, bruise or impact break) and lack of tire
rotation.
• Original equipment tires on new vehicles.
6. For staggered/split fitment applications (different size tires on the front and rear axles), Kumho Tire will cover half the number of miles
of the standard mileage warranty since these tires cannot be rotated as
recommended by Kumho.
III. ROAD HAZARD PROTECTION
Every KR21/ KU39/ KU27/ KU22 II/ KU31/ TA31/ TA11 (Available 3rd
Quarter 2015) steel belted radial passenger tire that has bean irreparably
damaged due to a normal road hazard conditions (e.g., irreparable cut,
puncture, snag, bruise or impact break) within the first 2/32 of the
original tread depth (O.T.D.) and within 12 months from the date of
purchase, will be replaced free of charge with an equivalent KUMHO tire.
To be eligible, you must present your original invoice showing date of
purchase. Tires not within 2/32 of the O.T.D. will not be issued a
pro-rated credit. Tires that reflect damage due to continued run flat or
acute underinflation are excluded.
KUMHO TIRES
152

V. CASING CREDIT
1. Casing of KUMHO radial commercial truck tires are warranted toremain serviceable through the second retreaded life for 66 months
from the date of manufacture.
2. KLS02a, KLD01a, and KLT02e casing warranty is valid through the second retreaded life for 72 months from the date of manufacture.
3. If an examination by KUMHO shows that a casing of a KUMHO radial truck tire delivers unsatisfactory service due to factors within the
manufacturer ’s control, KUMHO will give a credit toward the pur-
chase price of a comparable new KUMHO tire in the amount indicated
in the Casing Credit table.
Tire Size Casing Value
8.25R15, 7.50R16, 8R17.5 $30.00
215/75R17.5, 235/75R17.5 $30.00
225/70R19.5, 245/70R19.5 $30.00
265/70R19.5, 285/70R19.5 $30.00
8.25R16 $35.00
255/70R22.5 $50.00
9.00R20, 10R22.5 $60.00
10.00R20, 295/80R22.5 $80.00
11.00R20, 12.00R20 $90.00
10.00R22, 11.00R22, 12.00R24 $90.00
11R22.5, 295/75R22.5 $95.00
11R24.5, 285/75R24.5 $95.00
12R22.5, 315/80R22.5 $100.00
385/65R22.5, 425/65R22.5,
445/65R22.5 $100.00
4. Radial truck tires used in mining service are not eligible under this
program.
VI. REPLACEMENT WARRANTY
If you receive a replacement tire under this warranty, it will be covered by
the manufacturer ’s warranty and the supplemental limited mileage
warranty that Kumho Tire U.S.A., Inc., than gives on that tire.
THIS IS THE ONLY EXPRESS WARRANTY GIVEN BY KUMHO
APPLICABLE TO KUMHO/MARSHAL REPLACEMENT TIRES.
KUMHO DOES NOT MAKE ANY OTHER EXPRESS WARRANTY
KUMHO TIRES
154

MICHELIN
NOTE:

:our
vehicle
manufacturer
may
provide
additional
tire
warranty

coverage
over
and
above
what
is
provided
by
Michelin.
Consult
your

vehicle
owner ’s
manual
for
further
information.
NOTE:

Some
MICHELIN®
Self-Supporting
Zero
Pressure
(ZP)
tires
can
only
be

mounted
on
special
SH-M
(Symmetric
Hump
-
Modified)
wheels.
These

tires
bear
the
special
SH-M
designation,
molded
into
the
sidewall
of
the

tire,
next
to
the
ZP
designation.
DO
NOT
MOUNT
A
TIRE
WITH
THE

SH-M
DESIGNA TION

ON
THE
SIDEW ALL


ON
A
STANDARD

WHEEL.
DOING
SO
VOIDS
THIS
LIMITED
WARRANTY
AND
COULD

CAUSE
THE
TIRE
TO
BECOME
UNSERVICEABLE
AT
LOW
OR
ZERO

PRESSURE,
RESULTING
IN
SERIOUS
PERSONAL
INJURY
OR
DEA TH.

Treadwear
–
Mileage


Warranty
Coverage
for
MICHELIN®
Passenger

and
Light
Truck
Tires
MICHELIN®
passenger
and
light
truck
tires
are
covered
by
a
manufac-
turer ’s
limited
warranty
for
treadwear.
For
the
mileage
warranty
associ-
ated
with
a
specific
tire
line,
please
see
your
Michelin
tire
retailer
or
visit

us
at

www.michelinman.com/promise.
Some
vehicles
come
from
the

vehicle
manufacturer
with
“split
fitments”
–
meaning
different
size
tires

on
the
front
and
rear
axles.
Because
these
tires
cannot
be
rotated
as

recommended
by
Michelin,
the
mileage
warranty
on
each
rear
tire
will

cover
half
the
number
of
miles
as
the
standard
mileage
warranty
for
that

particular
tire
design.
Michelin
Self-Supporting
Zero
Pressure
(ZP)
tires

have
the
same
mileage
warranty
as
the
standard
tire
line
of
which
they

are
a
part,
up
to
but
not
exceeding
30,000
miles.
DOT-approved
compe-
tition
tires
(e.g.,
MICHELIN®
Pilot®
Sport
Cup
tires)
are
excluded
from

any
mileage
warranty .

MICHELIN®

tires
must
be
used


during


months
only,
defined
as
a
period


beginning
on
or
after
September

1st
of
a
given
year
and
ending
no
later
than
April
30th
of
the
following

year.
MICHELIN

tires
require
documentation
of
the
timing
of
the

installation
and
removal
of
the
tires
each

to
maintain
coverage

under
the
limited
warranty
for
treadwear .
An
important
reminder:
No
tire
manufacturer


can
guarantee
you
a
certain
number
of
miles
from

a
given
tire.
Driving
habits,
driving
conditions,
road
conditions,
and

vehicle
maintenance
all
play
a
part
in
the
tread
life
of
a
tire.
If
a
tire
does

not
reach
the
warranted
mileage,
and
the
owner
of
the
tires
has
complied

with
the
terms
and
conditions
of
the
warranty,
Michelin
will
replace
the



tires
as
described
under
“How
Replacement
Charges
are
calculated”.
161