clock setting Citroen BERLINGO 2005 1.G User Guide

Downloaded from www.Manualslib.com manuals search engine 230
ENGINECHECKING AND SETTING THE VALVE TIMING
Engine: RFK
Tensioning the timing belt.
Turn the tensioner roller (9)anti-clockwise, using a hexagonal spanner at «c».
Place the index «a»in position «e».
IMPERATIVE: The index «a» should go past the slot «f» by an angular value of 10°.
If it does not, replace the tensioner roller or the tensioner roller and timing belt assembly.
Then bring the index «a»to its adjustment position «f», by turning the tensioner roller in the direction
of the arrow «d».
WARNING: The index «a» must not go past the slot «f».
If it does, restart the operation to tension the timing belt.
IMPERATIVE : The tensioner roller must not turn during the tightening of its fixing. If it does
turn, restart the operation to tension the timing belt.
Tighten the screw (10)of the tensioner roller (9)to 2,1 ± 0,2 m.daN.
IMPERATIVE: The hexagonal tensioner roller drive should be at approx. 15° below the level of
the cylinder head gasket «g».
Otherwise, replace the tensioner roller or the tensioner roller and timing belt assembly.
B1EP1GXD
B1EP1GZC
C4
Angl.-t2-page135-239-2005 9/01/06 10:14 Page 230

Downloaded from www.Manualslib.com manuals search engine 233
ENGINE
CHECKING AND SETTING THE VALVE TIMING
Engines: 8HX - 8HZ
B1EP18EC
Checking the setting (continued).
Remove:
- The accessories drive belt.
- The accessories drive pulley.
- The lower timing cover (3).
IMPERATIVE: The magnetic track should show no signs of damage
and should not be approached by any other source of magnetism.
Reposition the screw (2).
Remove tool [3].
Rotate the engine by means of the crankshaft pinion screw (2)
(clockwise), to bring it to the pegging position.
Position the tool [4].
Peg the crankshaft pinion (1), using tool [5].
Peg the high pressure pump pinion, using tool [5].
NOTE: Index «a»of the roller tensioner must be centred within
the area «b».
Check the correct positioning of index «a».
Remove tools [4]and [5].
Rotate the engine ten times.
Fit the tools [4]and [5].
If pegging is not possible, carry out the operation to remove/refit the
timing belt
(see corresponding operation).
B1JP03SCB1EP18DCB1EP18FC
XSARA
Angl.-t2-page135-239-2005 9/01/06 10:14 Page 233

Downloaded from www.Manualslib.com manuals search engine 235
ENGINE
CHECKING AND SETTING THE VALVE TIMING
Engines: 8HX - 8HZ
Setting the timing (continued).
Remove the tool [3].
Rotate the engine by means of the crankshaft pinion screw (2)
(clockwise), to bring it to the pegging position.
Peg the camshaft pulley, using tool [4].
Peg:
- The crankshaft pinion (6), using tool [5].
- The high pressure pump pinion, using tool [5].
Support the engine with the aid of a roller jack equipped with a chock.
Remove:
- The RH engine support (7).
- The intermediate engine support
(right hand side)(8).
B1JP03SCB1EP18DCB1EP195CB1BP2LYC
XSARA
Angl.-t2-page135-239-2005 9/01/06 10:14 Page 235

Downloaded from www.Manualslib.com manuals search engine 241
ENGINE
CHECKING THE VALVE TIMING
Engines: 9HX - 9HY - 9HZ
Turn the engine in the normal direction of rotation until the peg [1]engages in the setting hole.
Peg the flywheel at «b», using tool [1].
Move aside the electrical harness (6).
Remove:
- The engine support (7).
- The screw (8).
- The accessories drive pulley (9).
- The lower timing cover (10).
- The upper timing cover (11).
- The tool [1].
Refit the screw (8).
Rotate the crankshaft six times
(clockwise).
IMPERATIVE: Never turn it backwards.
B1BP305C
B1EP1HJD
C4
Angl.-t2-page240-282-2005 9/01/06 10:16 Page 241

Downloaded from www.Manualslib.com manuals search engine 245
ENGINE
CHECKING AND SETTING THE VALVE TIMING
Engines: 9HX - 9HY - 9HZ
Checking and setting the timing (continued).
Peg the crankshaft at «e», using tool [3].
Remove:
- The timing belt protector (13).
- The engine speed sensor (14).
Slacken the screw (12)of the tensioner roller and keep it slackened using an allen spanner at «d».
Detension the timing belt by pivoting the tensioner roller
(clockwise).
Remove the timing belt, starting with the coolant pump pinion.
Checks.
ESSENTIAL: Just prior to refitting, proceed to the checks as below.
Check:
- That the rollers and the coolant pump pulley turn freely
(without play and without tight spot).
- That there are no signs of oil leaks (at the crankshaft and camshaft seals).
- That there are no leaks of coolant fluid (at the coolant pump).
- That the track of the engine speed sensor target (14)is not damaged or scratched.
Replace any components that are defective
(if necessary).
B1EP1HMC
C4
Angl.-t2-page240-282-2005 9/01/06 10:16 Page 245

Downloaded from www.Manualslib.com manuals search engine 247
ENGINE
CHECKING AND SETTING THE VALVE TIMING
Engines: 9HX - 9HY - 9HZ
Adjusting the timing belt tension.
Act on the tensioner roller (18)to align the marks «j»and «h», avoiding detensioning the timing belt,
using an allen spanner at «d».
Should this fail, repeat the operation to tension the timing belt.
Hold the tensioner roller (18).
Tighten the tensioner roller fixing nut to 3,7 ± 0,3 m.daN.
Check the position of the tensioner roller
(the alignment of the marks «j» and «h»should be correct).
Remove tools [2]and [3].
Rotate the crankshaft six times
(clockwise).
IMPERATIVE: Never rotate the engine backwards.
WARNING: Do not touch or damage the track of the target of the engine speed sensor (14).
Peg the crankshaft, using tool [3].
Check the position of the tensioner roller
(the alignment of the marks «j»and «h»should be correct).
If this is not the case, repeat the operation to tension the timing belt.
Peg the camshaft pulley, using tool [2].
B1EP1HNC
C4
Angl.-t2-page240-282-2005 9/01/06 10:16 Page 247

Downloaded from www.Manualslib.com manuals search engine 251
ENGINE
CHECKING AND SETTING THE VALVE TIMING
Engines: 9HZ - 9HY
Refit the screw (10).
Rotate the crankshaft six times
(clockwise).
IMPERATIVE: Never turn it backwards.
Peg the camshaft at «c», using tool [2]
(oil the peg).
WARNING: The magnetic track should not show any sign of damage and should not be
approached by any other magnetic source.
Peg the crankshaft at «d», using tool [3].
ESSENTIAL: Should it not be possible to peg the camshaft, check that the offset between
the camshaft pinion hole and the pegging hole is not more than 1 mm. If it is more, repeat
the operation to position the timing belt
(see corresponding operation).
Note: The index «e»of the dynamic tensioner roller should be centred in the interval «d».
Check the correct positioning of the index «e».
If it is not correct, repeat the operation to tension the timing belt
(see corresponding operation).
Remove tools [2] and [3].
B1EP1E4D
B1EP1E5C
XSARA PICASSO
Angl.-t2-page240-282-2005 9/01/06 10:16 Page 251

Downloaded from www.Manualslib.com manuals search engine 255
ENGINE
CHECKING AND SETTING THE VALVE TIMING
Engines: 9HZ - 9HY
B1EP1E6D
Refit the screw (10).
Turn the crankshaft to bring the camshaft towards its pegging point.
Peg the camshaft at «c», using tool [2]
(oil the pegs).
WARNING: Do not press or damage the track of the engine speed sensor target (13).
Peg the crankshaft at «e», using tool [3].
Remove:
- The timing belt protector (13).
- The engine speed sensor (14).
Slacken the screw (15)of the tensioner roller, and keep it slackened using an allen
spanner at «d».
Detension the timing belt by pivoting the tensioner roller
(clockwise).
Remove the timing belt, starting with the coolant pump pinion.
Checks.
ESSENTIAL: Just prior to refitting, proceed to the checks as below.
Check:
- That the rollers and the coolant pump pulley turn freely
(without play and without tight spot).
- That there are no signs of oil leaks (at the crankshaft and camshaft seals).
- That there are no leaks of coolant fluid (at the coolant pump).
- That the track of the engine speed sensor target (15)is not damaged or scratched.
Replace any components that are defective
(if necessary).
XSARA PICASSO
Angl.-t2-page240-282-2005 9/01/06 10:16 Page 255

Downloaded from www.Manualslib.com manuals search engine 257
ENGINE
CHECKING AND SETTING THE VALVE TIMING
Engines: 9HZ - 9HY
B1EP1E8C
Adjusting the timing belt tension.
Act on the tensioner roller (18)to align the marks «g»and «h», avoiding detensioning the
timing belt, using an allen spanner at «d».
Should this fail, repeat the operation to tension the timing belt.
Hold the tensioner roller (18).
Tighten the tensioner roller fixing nut to 3,7 ± 0,3 m.daN.
Check the position of the tensioner roller
(the alignment of the marks «g»and «h»should
be correct).
Remove tools [2] and [3].
Rotate the crankshaft six times
(clockwise).
IMPERATIVE: Never rotate the engine backwards.
WARNING: Do not touch or damage the track of the target of the engine speed sensor
(14).
Peg the crankshaft, using tool[3].
Check the position of the tensioner roller
(the alignment of the marks «g» and «h»should
be correct).
If this is not the case, repeat the operation to tension the timing belt.
Peg the camshaft pulley, using tool [2].
IMPERATIVE: Should it be impossible to peg the camshaft, check that the offset
between the camshaft hole and the pegging hole is not more than 1 mm. If the offset
is too great, repeat the operation.
Remove tools [2] and [3].
XSARA PICASSO
Angl.-t2-page240-282-2005 9/01/06 10:16 Page 257

Downloaded from www.Manualslib.com manuals search engine 261
ENGINE
CHECKING AND SETTING THE VALVE TIMING
Engine: WJY
Setting the timing (continued).
Peg the camshaft hub, using tool[4].
Peg the injection pump hub, using tool[3].
Slacken screws (5)and (6).
Slacken screw (9)of the tensioner roller (8).
Remove the timing belt.
Refitting.
Retighten screws (5)and (6) by hand.
Turn the pinions (10)and(7)clockwise in order to place them at end of slots.
Fit the timing belt on the crankshaft.
Hold the belt, using tool [5].
Position the timing belt in the following sequence:
- Guide roller (11).
- Injection pump pinion (7).
- Camshaft pinion (10).
- Coolant pump pinion (12).
- Tensioner roller (8).
B1EP16PDB1EP1EDCB1EP132C
XSARA
B1EP1EEC
Angl.-t2-page240-282-2005 9/01/06 10:16 Page 261